- 27 Apr, 2014 3 commits
-
-
Neil Horman authored
commit 6f8a1b33 upstream. Commit 03bbcb2e (iommu/vt-d: add quirk for broken interrupt remapping on 55XX chipsets) properly disables irq remapping on the 5500/5520 chipsets that don't correctly perform that feature. However, when I wrote it, I followed the errata sheet linked in that commit too closely, and explicitly tied the activation of the quirk to revision 0x13 of the chip, under the assumption that earlier revisions were not in the field. Recently a system was reported to be suffering from this remap bug and the quirk hadn't triggered, because the revision id register read at a lower value that 0x13, so the quirk test failed improperly. Given this, it seems only prudent to adjust this quirk so that any revision less than 0x13 has the quirk asserted. [ tglx: Removed the 0x12 comparison of pci id 3405 as this is covered by the <= 0x13 check already ] Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Link: http://lkml.kernel.org/r/1394649873-14913-1-git-send-email-nhorman@tuxdriver.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
commit a94cdd1f upstream. In read_all_bytes, we do unsigned char i; ... bt->read_data[0] = BMC2HOST; bt->read_count = bt->read_data[0]; ... for (i = 1; i <= bt->read_count; i++) bt->read_data[i] = BMC2HOST; If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the 'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the overflow and finish the loop after 255 iterations every time. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Reported-and-debugged-by:
Rui Hui Dian <rhdian@novell.com> Cc: Tomas Cech <tcech@suse.cz> Cc: Corey Minyard <minyard@acm.org> Cc: <openipmi-developer@lists.sourceforge.net> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Mikulas Patocka authored
commit e79323bd upstream. smp_read_barrier_depends() can be used if there is data dependency between the readers - i.e. if the read operation after the barrier uses address that was obtained from the read operation before the barrier. In this file, there is only control dependency, no data dependecy, so the use of smp_read_barrier_depends() is incorrect. The code could fail in the following way: * the cpu predicts that idx < entries is true and starts executing the body of the for loop * the cpu fetches map->extent[0].first and map->extent[0].count * the cpu fetches map->nr_extents * the cpu verifies that idx < extents is true, so it commits the instructions in the body of the for loop The problem is that in this scenario, the cpu read map->extent[0].first and map->nr_extents in the wrong order. We need a full read memory barrier to prevent it. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
- 14 Apr, 2014 37 commits
-
-
Greg Kroah-Hartman authored
-
Stephen Boyd authored
commit 3617f2ca upstream. When a CPU is hot removed we'll cancel all the delayed work items via gov_cancel_work(). Normally this will just cancels a delayed timer on each CPU that the policy is managing and the work won't run, but if the work is already running the workqueue code will wait for the work to finish before continuing to prevent the work items from re-queuing themselves like they normally do. This scheme will work most of the time, except for the case where the work function determines that it should adjust the delay for all other CPUs that the policy is managing. If this scenario occurs, the canceling CPU will cancel its own work but queue up the other CPUs works to run. For example: CPU0 CPU1 ---- ---- cpu_down() ... __cpufreq_remove_dev() cpufreq_governor_dbs() case CPUFREQ_GOV_STOP: gov_cancel_work(dbs_data, policy); cpu0 work is canceled timer is canceled cpu1 work is canceled <work runs> <waits for cpu1> od_dbs_timer() gov_queue_work(*, *, true); cpu0 work queued cpu1 work queued cpu2 work queued ... cpu1 work is canceled cpu2 work is canceled ... At the end of the GOV_STOP case cpu0 still has a work queued to run although the code is expecting all of the works to be canceled. __cpufreq_remove_dev() will then proceed to re-initialize all the other CPUs works except for the CPU that is going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs() will trample over the queued work and debugobjects will spit out a warning: WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc() ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x10 Modules linked in: CPU: 0 PID: 1491 Comm: sh Tainted: G W 3.10.0 #19 [<c010c178>] (unwind_backtrace+0x0/0x11c) from [<c0109dec>] (show_stack+0x10/0x14) [<c0109dec>] (show_stack+0x10/0x14) from [<c01904cc>] (warn_slowpath_common+0x4c/0x6c) [<c01904cc>] (warn_slowpath_common+0x4c/0x6c) from [<c019056c>] (warn_slowpath_fmt+0x2c/0x3c) [<c019056c>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0388a7c>] (debug_print_object+0x94/0xbc) [<c0388a7c>] (debug_print_object+0x94/0xbc) from [<c0388e34>] (__debug_object_init+0x2d0/0x340) [<c0388e34>] (__debug_object_init+0x2d0/0x340) from [<c019e3b0>] (init_timer_key+0x14/0xb0) [<c019e3b0>] (init_timer_key+0x14/0xb0) from [<c0635f78>] (cpufreq_governor_dbs+0x3e8/0x5f8) [<c0635f78>] (cpufreq_governor_dbs+0x3e8/0x5f8) from [<c06325a0>] (__cpufreq_governor+0xdc/0x1a4) [<c06325a0>] (__cpufreq_governor+0xdc/0x1a4) from [<c0633704>] (__cpufreq_remove_dev.isra.10+0x3b4/0x434) [<c0633704>] (__cpufreq_remove_dev.isra.10+0x3b4/0x434) from [<c08989f4>] (cpufreq_cpu_callback+0x60/0x80) [<c08989f4>] (cpufreq_cpu_callback+0x60/0x80) from [<c08a43c0>] (notifier_call_chain+0x38/0x68) [<c08a43c0>] (notifier_call_chain+0x38/0x68) from [<c01938e0>] (__cpu_notify+0x28/0x40) [<c01938e0>] (__cpu_notify+0x28/0x40) from [<c0892ad4>] (_cpu_down+0x7c/0x2c0) [<c0892ad4>] (_cpu_down+0x7c/0x2c0) from [<c0892d3c>] (cpu_down+0x24/0x40) [<c0892d3c>] (cpu_down+0x24/0x40) from [<c0893ea8>] (store_online+0x2c/0x74) [<c0893ea8>] (store_online+0x2c/0x74) from [<c04519d8>] (dev_attr_store+0x18/0x24) [<c04519d8>] (dev_attr_store+0x18/0x24) from [<c02a69d4>] (sysfs_write_file+0x100/0x148) [<c02a69d4>] (sysfs_write_file+0x100/0x148) from [<c0255c18>] (vfs_write+0xcc/0x174) [<c0255c18>] (vfs_write+0xcc/0x174) from [<c0255f70>] (SyS_write+0x38/0x64) [<c0255f70>] (SyS_write+0x38/0x64) from [<c0106120>] (ret_fast_syscall+0x0/0x30) Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Xiaoguang Chen authored
commit 95731ebb upstream. Cpufreq governors' stop and start operations should be carried out in sequence. Otherwise, there will be unexpected behavior, like in the example below. Suppose there are 4 CPUs and policy->cpu=CPU0, CPU1/2/3 are linked to CPU0. The normal sequence is: 1) Current governor is userspace. An application tries to set the governor to ondemand. It will call __cpufreq_set_policy() in which it will stop the userspace governor and then start the ondemand governor. 2) Current governor is userspace. The online of CPU3 runs on CPU0. It will call cpufreq_add_policy_cpu() in which it will first stop the userspace governor, and then start it again. If the sequence of the above two cases interleaves, it becomes: 1) Application stops userspace governor 2) Hotplug stops userspace governor which is a problem, because the governor shouldn't be stopped twice in a row. What happens next is: 3) Application starts ondemand governor 4) Hotplug starts a governor In step 4, the hotplug is supposed to start the userspace governor, but now the governor has been changed by the application to ondemand, so the ondemand governor is started once again, which is incorrect. The solution is to prevent policy governors from being stopped multiple times in a row. A governor should only be stopped once for one policy. After it has been stopped, no more governor stop operations should be executed. Also add a mutex to serialize governor operations. [rjw: Changelog. And you owe me a beverage of my choice.] Signed-off-by:
Xiaoguang Chen <chenxg@marvell.com> Acked-by:
-
Ard Biesheuvel authored
commit 8ceee728 upstream. The GHASH setkey() function uses SSE registers but fails to call kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and then having to deal with the restriction that they cannot be called from interrupt context, move the setkey() implementation to the C domain. Note that setkey() does not use any particular SSE features and is not expected to become a performance bottleneck. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by:
H. Peter Anvin <hpa@linux.intel.com> Fixes: 0e1227d3 (crypto: ghash - Add PCLMULQDQ accelerated implementation) Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Finn Thain authored
commit e571c58f upstream. Skip the futex_atomic_cmpxchg_inatomic() test in futex_init(). It causes a fatal exception on 68030 (and presumably 68020 also). Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1403061006440.5525@nippy.intranetSigned-off-by:
-
Heiko Carstens authored
commit 03b8c7b6 upstream. If an architecture has futex_atomic_cmpxchg_inatomic() implemented and there is no runtime check necessary, allow to skip the test within futex_init(). This allows to get rid of some code which would always give the same result, and also allows the compiler to optimize a couple of if statements away. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Finn Thain <fthain@telegraphics.com.au> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Link: http://lkml.kernel.org/r/20140302120947.GA3641@osirisSigned-off-by:
-
Vineet Gupta authored
commit 61fb4bfc upstream. Despite the switch to right UART driver (prev patch), serial console still doesn't work due to missing CONFIG_SERIAL_OF_PLATFORM Also fix the default cmdline in DT to not refer to out-of-tree ARC framebuffer driver for console. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <Francois.Bedard@synopsys.com> Signed-off-by:
-
Mischa Jonker authored
commit 6eda477b upstream. The Synopsys APB DW UART has a couple of special features that are not in the System C model. In 3.8, the 8250_dw driver didn't really use these features, but from 3.9 onwards, the 8250_dw driver has become incompatible with our model. Signed-off-by:
Mischa Jonker <mjonker@synopsys.com> Signed-off-by:
-
Sasha Levin authored
[ Upstream commit bf39b424 ] Binding might result in a NULL device which is later dereferenced without checking. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 7563487c ] There are three buffer overflows addressed in this patch. 1) In isdnloop_fake_err() we add an 'E' to a 60 character string and then copy it into a 60 character buffer. I have made the destination buffer 64 characters and I'm changed the sprintf() to a snprintf(). 2) In isdnloop_parse_cmd(), p points to a 6 characters into a 60 character buffer so we have 54 characters. The ->eazlist[] is 11 characters long. I have modified the code to return if the source buffer is too long. 3) In isdnloop_command() the cbuf[] array was 60 characters long but the max length of the string then can be up to 79 characters. I made the cbuf array 80 characters long and changed the sprintf() to snprintf(). I also removed the temporary "dial" buffer and changed it to use "p" directly. Unfortunately, we pass the "cbuf" string from isdnloop_command() to isdnloop_writecmd() which truncates anything over 60 characters to make it fit in card->omsg[]. (It can accept values up to 255 characters so long as there is a '\n' character every 60 characters). For now I have just fixed the memory corruption bug and left the other problems in this driver alone. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
YOSHIFUJI Hideaki authored
[ Upstream commit 77bc6bed ] Return -EINVAL unless all of user-given strings are correctly NUL-terminated. Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
Pablo Neira authored
[ Upstream commit 8b7b9324 ] nla_strcmp compares the string length plus one, so it's implicitly including the nul-termination in the comparison. int nla_strcmp(const struct nlattr *nla, const char *str) { int len = strlen(str) + 1; ... d = memcmp(nla_data(nla), str, len); However, if NLA_STRING is used, userspace can send us a string without the nul-termination. This is a problem since the string comparison will not match as the last byte may be not the nul-termination. Fix this by skipping the comparison of the nul-termination if the attribute data is nul-terminated. Suggested by Thomas Graf. Cc: Florian Westphal <fw@strlen.de> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 43a43b60 ] After commit c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue") some counters are now updated in process context and thus need to disable bh before doing so, otherwise deadlocks can happen on 32-bit archs. Fabio Estevam noticed this while while mounting a NFS volume on an ARM board. As a compensation for missing this I looked after the other *_STATS_BH and found three other calls which need updating: 1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling) 2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ... (only in case of icmp protocol with raw sockets in error handling) 3) ping6_v6_sendmsg (error handling) Fixes: c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue") Reported-by:
Fabio Estevam <festevam@gmail.com> Tested-by:
Fabio Estevam <fabio.estevam@freescale.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Paul Durrant authored
[ Upstream commit 0576eddf ] This patch removes a test in start_new_rx_buffer() that checks whether a copy operation is less than MAX_BUFFER_OFFSET in length, since MAX_BUFFER_OFFSET is defined to be PAGE_SIZE and the only caller of start_new_rx_buffer() already limits copy operations to PAGE_SIZE or less. Signed-off-by:
Paul Durrant <paul.durrant@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Sander Eikelenboom <linux@eikelenboom.it> Reported-By:
Sander Eikelenboom <linux@eikelenboom.it> Tested-By:
-
Michael S. Tsirkin authored
[ Upstream commit a39ee449 ] vhost fails to validate negative error code from vhost_get_vq_desc causing a crash: we are using -EFAULT which is 0xfffffff2 as vector size, which exceeds the allocated size. The code in question was introduced in commit 8dd014ad vhost-net: mergeable buffers support CVE-2014-0055 Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
[ Upstream commit d8316f39 ] When mergeable buffers are disabled, and the incoming packet is too large for the rx buffer, get_rx_bufs returns success. This was intentional in order for make recvmsg truncate the packet and then handle_rx would detect err != sock_len and drop it. Unfortunately we pass the original sock_len to recvmsg - which means we use parts of iov not fully validated. Fix this up by detecting this overrun and doing packet drop immediately. CVE-2014-0077 Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit fc0d48b8 ] Currently, if the card supports CTAG acceleration we do not account for the vlan header even if we are configuring an 8021AD vlan. This may not be best since we'll do software tagging for 8021AD which will cause data copy on skb head expansion Configure the length based on available hw offload capabilities and vlan protocol. CC: Patrick McHardy <kaber@trash.net> Signed-off-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Oliver Neukum authored
[ Upstream commit 14a0d635 ] This fixes a race which happens by freeing an object on the stack. Quoting Julius: > The issue is > that it calls usbnet_terminate_urbs() before that, which temporarily > installs a waitqueue in dev->wait in order to be able to wait on the > tasklet to run and finish up some queues. The waiting itself looks > okay, but the access to 'dev->wait' is totally unprotected and can > race arbitrarily. I think in this case usbnet_bh() managed to succeed > it's dev->wait check just before usbnet_terminate_urbs() sets it back > to NULL. The latter then finishes and the waitqueue_t structure on its > stack gets overwritten by other functions halfway through the > wake_up() call in usbnet_bh(). The fix is to just not allocate the data structure on the stack. As dev->wait is abused as a flag it also takes a runtime PM change to fix this bug. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Reported-by:
Grant Grundler <grundler@google.com> Tested-by:
-
Vlad Yasevich authored
[ Upstream commit 51dfe7b9 ] Including hardware acceleration features in vlan_features breaks stacked vlans (Q-in-Q) by marking the bottom vlan interface as capable of acceleration. This causes one of the tags to be lost and the packets are sent with a sing vlan header. CC: Nithin Nayak Sujir <nsujir@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Li RongQing authored
[ Not applicable upstream commit, the code here has been removed upstream. ] Neighbor Solicitation is ipv6 protocol, so we should check skb->protocol with ETH_P_IPV6 Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Cc: WANG Cong <amwang@redhat.com> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit f518338b ] Commit 812e44dd ("ip6mr: advertise new mfc entries via rtnl") reuses the function ip6mr_fill_mroute() to notify mfc events. But this function was used only for dump and thus was always setting the flag NLM_F_MULTI, which is wrong in case of a single notification. Libraries like libnl will wait forever for NLMSG_DONE. CC: Thomas Graf <tgraf@suug.ch> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 65886f43 ] Commit 8cd3ac9f ("ipmr: advertise new mfc entries via rtnl") reuses the function ipmr_fill_mroute() to notify mfc events. But this function was used only for dump and thus was always setting the flag NLM_F_MULTI, which is wrong in case of a single notification. Libraries like libnl will wait forever for NLMSG_DONE. CC: Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 1c104a6b ] Commit 3ff661c3 ("net: rtnetlink notify events for FDB NTF_SELF adds and deletes") reuses the function nlmsg_populate_fdb_fill() to notify fdb events. But this function was used only for dump and thus was always setting the flag NLM_F_MULTI, which is wrong in case of a single notification. Libraries like libnl will wait forever for NLMSG_DONE. CC: Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
David Stevens authored
[ Upstream commit 7346135d ] This patch fixes a NULL pointer dereference in the event of an skb allocation failure in arp_reduce(). Signed-Off-By:
David L Stevens <dlstevens@us.ibm.com> Acked-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
-
lucien authored
[ Upstream commit e367c2d0 ] In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as transport),the ipsec header need to be added in the first fragment, so the mtu will decrease to reserve space for it, then the second fragment come, the mtu should be turn back, as the commit 0c183379 said. however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use *mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway equal with the first fragment's. and cannot turn back. when I test through ping6 -c1 -s5000 $ip (mtu=1280): ...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232 ...frag (1232|1216) ...frag (2448|1216) ...frag (3664|1216) ...frag (4880|164) which should be: ...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232 ...frag (1232|1232) ...frag (2464|1232) ...frag (3696|1232) ...frag (4928|116) so delete the min() when change back the mtu. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Fixes: 75a493e6 ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size") Acked-by:
-
Heiner Kallweit authored
[ Upstream commit ecab6701 ] tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore age needs to be added to the condition. Age calculation in ipv6_create_tempaddr is different from the one in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS. This can cause age in ipv6_create_tempaddr to be less than the one in addrconf_verify and therefore unnecessary temporary address to be generated. Use age calculation as in addrconf_modify to avoid this. Signed-off-by:
Heiner Kallweit <heiner.kallweit@web.de> Signed-off-by:
-
Matthew Leach authored
[ Upstream commit dbb490b9 ] When copying in a struct msghdr from the user, if the user has set the msg_namelen parameter to a negative value it gets clamped to a valid size due to a comparison between signed and unsigned values. Ensure the syscall errors when the user passes in a negative value. Signed-off-by:
Matthew Leach <matthew.leach@arm.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit c3f9b018 ] Lars Persson reported following deadlock : -000 |M:0x0:0x802B6AF8(asm) <-- arch_spin_lock -001 |tcp_v4_rcv(skb = 0x8BD527A0) <-- sk = 0x8BE6B2A0 -002 |ip_local_deliver_finish(skb = 0x8BD527A0) -003 |__netif_receive_skb_core(skb = 0x8BD527A0, ?) -004 |netif_receive_skb(skb = 0x8BD527A0) -005 |elk_poll(napi = 0x8C770500, budget = 64) -006 |net_rx_action(?) -007 |__do_softirq() -008 |do_softirq() -009 |local_bh_enable() -010 |tcp_rcv_established(sk = 0x8BE6B2A0, skb = 0x87D3A9E0, th = 0x814EBE14, ?) -011 |tcp_v4_do_rcv(sk = 0x8BE6B2A0, skb = 0x87D3A9E0) -012 |tcp_delack_timer_handler(sk = 0x8BE6B2A0) -013 |tcp_release_cb(sk = 0x8BE6B2A0) -014 |release_sock(sk = 0x8BE6B2A0) -015 |tcp_sendmsg(?, sk = 0x8BE6B2A0, ?, ?) -016 |sock_sendmsg(sock = 0x8518C4C0, msg = 0x87D8DAA8, size = 4096) -017 |kernel_sendmsg(?, ?, ?, ?, size = 4096) -018 |smb_send_kvec() -019 |smb_send_rqst(server = 0x87C4D400, rqst = 0x87D8DBA0) -020 |cifs_call_async() -021 |cifs_async_writev(wdata = 0x87FD6580) -022 |cifs_writepages(mapping = 0x852096E4, wbc = 0x87D8DC88) -023 |__writeback_single_inode(inode = 0x852095D0, wbc = 0x87D8DC88) -024 |writeback_sb_inodes(sb = 0x87D6D800, wb = 0x87E4A9C0, work = 0x87D8DD88) -025 |__writeback_inodes_wb(wb = 0x87E4A9C0, work = 0x87D8DD88) -026 |wb_writeback(wb = 0x87E4A9C0, work = 0x87D8DD88) -027 |wb_do_writeback(wb = 0x87E4A9C0, force_wait = 0) -028 |bdi_writeback_workfn(work = 0x87E4A9CC) -029 |process_one_work(worker = 0x8B045880, work = 0x87E4A9CC) -030 |worker_thread(__worker = 0x8B045880) -031 |kthread(_create = 0x87CADD90) -032 |ret_from_kernel_thread(asm) Bug occurs because __tcp_checksum_complete_user() enables BH, assuming it is running from softirq context. Lars trace involved a NIC without RX checksum support but other points are problematic as well, like the prequeue stuff. Problem is triggered by a timer, that found socket being owned by user. tcp_release_cb() should call tcp_write_timer_handler() or tcp_delack_timer_handler() in the appropriate context : BH disabled and socket lock held, but 'owned' field cleared, as if they were running from timer handlers. Fixes: 6f458dfb ("tcp: improve latencies of timer triggered events") Reported-by:
Lars Persson <lars.persson@axis.com> Tested-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Peter Boström authored
[ Upstream commit dd38743b ] With TX VLAN offload enabled the source MAC address for frames sent using the VLAN interface is currently set to the address of the real interface. This is wrong since the VLAN interface may be configured with a different address. The bug was introduced in commit 2205369a ("vlan: Fix header ops passthru when doing TX VLAN offload."). This patch sets the source address before calling the create function of the real interface. Signed-off-by:
Peter Boström <peter.bostrom@netrounds.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit c88507fb ] DST_NOCOUNT should only be used if an authorized user adds routes locally. In case of routes which are added on behalf of router advertisments this flag must not get used as it allows an unlimited number of routes getting added remotely. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
-
Anton Nayshtut authored
[ Upstream commit d2d273ff ] Without this fix, ipv6_exthdrs_offload_init doesn't register IPPROTO_DSTOPTS offload, but returns 0 (as the IPPROTO_ROUTING registration actually succeeds). This then causes the ipv6_gso_segment to drop IPv6 packets with IPPROTO_DSTOPTS header. The issue detected and the fix verified by running MS HCK Offload LSO test on top of QEMU Windows guests, as this test sends IPv6 packets with IPPROTO_DSTOPTS. Signed-off-by:
Anton Nayshtut <anton@swortex.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit de144391 ] Some applications didn't expect recvmsg() on a non blocking socket could return -EINTR. This possibility was added as a side effect of commit b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines"). To hit this bug, you need to be a bit unlucky, as the u->readlock mutex is usually held for very small periods. Fixes: b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines") Signed-off-by:
-
Florian Westphal authored
[ Upstream commit e588e2f2 ] Quoting Alexander Aring: While fragmentation and unloading of 6lowpan module I got this kernel Oops after few seconds: BUG: unable to handle kernel paging request at f88bbc30 [..] Modules linked in: ipv6 [last unloaded: 6lowpan] Call Trace: [<c012af4c>] ? call_timer_fn+0x54/0xb3 [<c012aef8>] ? process_timeout+0xa/0xa [<c012b66b>] run_timer_softirq+0x140/0x15f Problem is that incomplete frags are still around after unload; when their frag expire timer fires, we get crash. When a netns is removed (also done when unloading module), inet_frag calls the evictor with 'force' argument to purge remaining frags. The evictor loop terminates when accounted memory ('work') drops to 0 or the lru-list becomes empty. However, the mem accounting is done via percpu counters and may not be accurate, i.e. loop may terminate prematurely. Alter evictor to only stop once the lru list is empty when force is requested. Reported-by:
Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Reported-by:
Alexander Aring <alex.aring@gmail.com> Tested-by:
Florian Westphal <fw@strlen.de> Acked-by:
-
Linus Lüssing authored
[ Upstream commit 6565b9ee ] MLD queries are supposed to have an IPv6 link-local source address according to RFC2710, section 4 and RFC3810, section 5.1.14. This patch adds a sanity check to ignore such broken MLD queries. Without this check, such malformed MLD queries can result in a denial of service: The queries are ignored by any MLD listener therefore they will not respond with an MLD report. However, without this patch these malformed MLD queries would enable the snooping part in the bridge code, potentially shutting down the according ports towards these hosts for multicast traffic as the bridge did not learn about these listeners. Reported-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Linus Lüssing <linus.luessing@web.de> Reviewed-by:
-
Daniel Borkmann authored
[ Upstream commit c485658b ] While working on ec0223ec ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable"), we noticed that there's a skb memory leakage in the error path. Running the same reproducer as in ec0223ec and by unconditionally jumping to the error label (to simulate an error condition) in sctp_sf_do_5_1D_ce() receive path lets kmemleak detector bark about the unfreed chunk->auth_chunk skb clone: Unreferenced object 0xffff8800b8f3a000 (size 256): comm "softirq", pid 0, jiffies 4294769856 (age 110.757s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 89 ab 75 5e d4 01 58 13 00 00 00 00 00 00 00 00 ..u^..X......... backtrace: [<ffffffff816660be>] kmemleak_alloc+0x4e/0xb0 [<ffffffff8119f328>] kmem_cache_alloc+0xc8/0x210 [<ffffffff81566929>] skb_clone+0x49/0xb0 [<ffffffffa0467459>] sctp_endpoint_bh_rcv+0x1d9/0x230 [sctp] [<ffffffffa046fdbc>] sctp_inq_push+0x4c/0x70 [sctp] [<ffffffffa047e8de>] sctp_rcv+0x82e/0x9a0 [sctp] [<ffffffff815abd38>] ip_local_deliver_finish+0xa8/0x210 [<ffffffff815a64af>] nf_reinject+0xbf/0x180 [<ffffffffa04b4762>] nfqnl_recv_verdict+0x1d2/0x2b0 [nfnetlink_queue] [<ffffffffa04aa40b>] nfnetlink_rcv_msg+0x14b/0x250 [nfnetlink] [<ffffffff815a3269>] netlink_rcv_skb+0xa9/0xc0 [<ffffffffa04aa7cf>] nfnetlink_rcv+0x23f/0x408 [nfnetlink] [<ffffffff815a2bd8>] netlink_unicast+0x168/0x250 [<ffffffff815a2fa1>] netlink_sendmsg+0x2e1/0x3f0 [<ffffffff8155cc6b>] sock_sendmsg+0x8b/0xc0 [<ffffffff8155d449>] ___sys_sendmsg+0x369/0x380 What happens is that commit bbd0d598 clones the skb containing the AUTH chunk in sctp_endpoint_bh_rcv() when having the edge case that an endpoint requires COOKIE-ECHO chunks to be authenticated: ---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ----------> <------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] --------- ------------------ AUTH; COOKIE-ECHO ----------------> <-------------------- COOKIE-ACK --------------------- When we enter sctp_sf_do_5_1D_ce() and before we actually get to the point where we process (and subsequently free) a non-NULL chunk->auth_chunk, we could hit the "goto nomem_init" path from an error condition and thus leave the cloned skb around w/o freeing it. The fix is to centrally free such clones in sctp_chunk_destroy() handler that is invoked from sctp_chunk_free() after all refs have dropped; and also move both kfree_skb(chunk->auth_chunk) there, so that chunk->auth_chunk is either NULL (since sctp_chunkify() allocs new chunks through kmem_cache_zalloc()) or non-NULL with a valid skb pointer. chunk->skb and chunk->auth_chunk are the only skbs in the sctp_chunk structure that need to be handeled. While at it, we should use consume_skb() for both. It is the same as dev_kfree_skb() but more appropriately named as we are not a device but a protocol. Also, this effectively replaces the kfree_skb() from both invocations into consume_skb(). Functions are the same only that kfree_skb() assumes that the frame was being dropped after a failure (e.g. for tools like drop monitor), usage of consume_skb() seems more appropriate in function sctp_chunk_destroy() though. Fixes: bbd0d598 ("[SCTP]: Implement the receive and verification of AUTH chunk") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <yasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 24b9bf43 ] I stumbled upon this very serious bug while hunting for another one, it's a very subtle race condition between inet_frag_evictor, inet_frag_intern and the IPv4/6 frag_queue and expire functions (basically the users of inet_frag_kill/inet_frag_put). What happens is that after a fragment has been added to the hash chain but before it's been added to the lru_list (inet_frag_lru_add) in inet_frag_intern, it may get deleted (either by an expired timer if the system load is high or the timer sufficiently low, or by the fraq_queue function for different reasons) before it's added to the lru_list, then after it gets added it's a matter of time for the evictor to get to a piece of memory which has been freed leading to a number of different bugs depending on what's left there. I've been able to trigger this on both IPv4 and IPv6 (which is normal as the frag code is the same), but it's been much more difficult to trigger on IPv4 due to the protocol differences about how fragments are treated. The setup I used to reproduce this is: 2 machines with 4 x 10G bonded in a RR bond, so the same flow can be seen on multiple cards at the same time. Then I used multiple instances of ping/ping6 to generate fragmented packets and flood the machines with them while running other processes to load the attacked machine. *It is very important to have the _same flow_ coming in on multiple CPUs concurrently. Usually the attacked machine would die in less than 30 minutes, if configured properly to have many evictor calls and timeouts it could happen in 10 minutes or so. An important point to make is that any caller (frag_queue or timer) of inet_frag_kill will remove both the timer refcount and the original/guarding refcount thus removing everything that's keeping the frag from being freed at the next inet_frag_put. All of this could happen before the frag was ever added to the LRU list, then it gets added and the evictor uses a freed fragment. An example for IPv6 would be if a fragment is being added and is at the stage of being inserted in the hash after the hash lock is released, but before inet_frag_lru_add executes (or is able to obtain the lru lock) another overlapping fragment for the same flow arrives at a different CPU which finds it in the hash, but since it's overlapping it drops it invoking inet_frag_kill and thus removing all guarding refcounts, and afterwards freeing it by invoking inet_frag_put which removes the last refcount added previously by inet_frag_find, then inet_frag_lru_add gets executed by inet_frag_intern and we have a freed fragment in the lru_list. The fix is simple, just move the lru_add under the hash chain locked region so when a removing function is called it'll have to wait for the fragment to be added to the lru_list, and then it'll remove it (it works because the hash chain removal is done before the lru_list one and there's no window between the two list adds when the frag can get dropped). With this fix applied I couldn't kill the same machine in 24 hours with the same setup. Fixes: 3ef0eb0d ("net: frag, move LRU list maintenance outside of rwlock") CC: Florian Westphal <fw@strlen.de> CC: Jesper Dangaard Brouer <brouer@redhat.com> CC: David S. Miller <davem@davemloft.net> Signed-off-by:
Nikolay Aleksandrov <nikolay@redhat.com> Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Daniel Fu authored
commit 3b9c10e9 upstream. If the current CPU has no cpuidle driver, drv will be NULL in cpuidle_driver_ref(). Check if that is the case before trying to bump up the driver's refcount to prevent the kernel from crashing. [rjw: Subject and changelog] Signed-off-by:
Daniel Fu <danifu@nvidia.com> Signed-off-by:
-
