Add support for R-Car V3U. The V3U IP differs a bit from its siblings in
such way that it have 4 TSC nodes and the interrupts are not routed to
the INTC-AP but to the ECM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126223028.3119044-2-niklas.soderlund+renesas@ragnatech.se

Currently the code checks the interval value when the temperature is
read which is bad for two reasons:

 - checking and setting the interval in the get_temp callback is
   inaccurate and awful, that can be done when changing the value.

 - Changing the thermal zone structure internals is an abuse of the
   exported structure, moreover no lock is taken here.

The goal of this patch is to solve the first item by using the 'set'
function called when changing the interval. The check is done there
and removed from the get_temp function. If the thermal zone was not
initialized yet, the interval is not updated in this case as that will
happen in the init function when registering the thermal zone device.

I don't have any hardware to test the changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Peter Kaestle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201203071738.2363701-2-daniel.lezcano@linaro.org

The module parameter can be set by using ops to get and set the
values. The change will allow to check the correctness of the interval
value everytime it is changed instead of checking in the get_temp
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Peter Kaestle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201203071738.2363701-1-daniel.lezcano@linaro.org

Prior to returning an error in probe, disable the previously
enabled clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-2-festevam@gmail.com

Currently the error message does not print the correct error code.

Fix it by initializing 'ret' to the proper error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-1-festevam@gmail.com

Remove the usage of interrupts for the normal temperature operation and
depend on the polling performed by the thermal core. This is done to
prepare to use the interrupts as they are intended to trigger once
specific trip points are passed and not to react to temperature changes
in the normal operational range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126220923.3107213-1-niklas.soderlund+renesas@ragnatech.se

The only usage of these structs is to assign their address to the
thermal_zone_attribute_groups array, which consists of pointers to
const, so make them const to allow the compiler to put them in read-only
memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201128234342.36684-1-rikard.falkeborn@gmail.com

The PID coefficients should be estimated again when there was a change to
sustainable power value made by user. This change removes unused argument
'force' and makes the function ready for such updates.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-4-lukasz.luba@arm.com

The sustainable power value might come from the Device Tree or can be
estimated in run time. The sustainable power might be updated by the user
via sysfs interface, which should trigger new estimation of PID
coefficients. There is no need to estimate it every time when the
governor is called and temperature is high. Instead, store the estimated
value and make it available via standard sysfs interface, so it can be
checked from the user-space.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-3-lukasz.luba@arm.com

Intelligent Power Allocation (IPA) is built around the PID controller
concept. The initialization code tries to setup the environment based on
the information available in DT or estimate the value based on minimum
power reported by each of the cooling device. The estimation will have an
impact on the PID controller behaviour via the related 'k_po', 'k_pu',
'k_i' coefficients and also on the power budget calculation.

This change prevents the situation when 'k_i' is relatively big compared
to 'k_po' and 'k_pu' values. This might happen when the estimation for
'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are
small.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-2-lukasz.luba@arm.com

The reference to acpi_gbl_FADT causes a build error when ACPI is not
enabled. Fix by making that conditional on CONFIG_ACPI.

../drivers/thermal/intel/intel_pch_thermal.c: In function 'pch_wpt_suspend':
../drivers/thermal/intel/intel_pch_thermal.c:217:8: error: 'acpi_gbl_FADT' undeclared (first use in this function); did you mean 'acpi_get_type'?
  if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
        ^~~~~~~~~~~~~

Fixes: ef63b043 ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117023807.8266-1-rdunlap@infradead.org

Many monitoring tools read the CPU temperature using the hwmon
interface. Expose the thermal sensors on Amlogic boards as hwmon
devices.

Without this lm_sensors' "sensors" tool does not find any temperature
sensors. Now it prints:
  cpu_thermal-virtual-0
  Adapter: Virtual device
  temp1:        +44.7 C  (crit = +110.0 C)

  ddr_thermal-virtual-0
  Adapter: Virtual device
  temp1:        +45.9 C  (crit = +110.0 C)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201115190658.631578-1-martin.blumenstingl@googlemail.com

I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.

I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de

The sysfs stats for cooling devices shows the time_in_state in msec,
remove the unwanted usertime comment.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/d5461bdf9ab6b6fee7f28f538582edbb426aa077.1605004905.git.viresh.kumar@linaro.org

- Factor out common required properties,
  - "interrupts", "clocks", and "power-domains" are required on R-Mobile
    APE6, too,
  - Invert logic to simplify descriptions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201028153541.1736279-1-geert+renesas@glider.be

If state has not changed successfully and we updated cpufreq_state,
next time when the new state is equal to cpufreq_state (not changed
successfully last time), we will return directly and miss a
freq_qos_update_request() that should have been.

Fixes: 5130802d ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Cc: v5.4+ <stable@vger.kernel.org> # v5.4+
Signed-off-by: Zhuguangqing <zhuguangqing@xiaomi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106092243.15574-1-zhuguangqing83@gmail.com

Function thermal_add_hwmon_sysfs, hwmon will be NULL when
new_hwmon_device = 0, so there is no need to check, kfree will
handle NULL point.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201102023121.3312-1-bernard@vivo.com

The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com

When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com

MT8516 does not support thermal reset. Use device_reset_optional
instead of device_reset.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-3-fparent@baylibre.com

Add binding documentation for the MediaTek MT8516 SoC.
The SoC thermal IP is similar to MT2701.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-2-fparent@baylibre.com

MT8516 Thermal IP does not support reset. Make the resets property
optional in order to be able to support MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-1-fparent@baylibre.com

On RT or even on mainline with 'threadirqs' on the command line all
interrupts which are not explicitly requested with IRQF_NO_THREAD
run their handlers in thread context. The same applies to soft interrupts.
That means they are subject to the normal scheduler rules and no other
code is going to acquire that lock from hard interrupt context either,
so the irqsave() here is pointless in all cases.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1603760790-37748-1-git-send-email-tiantao6@hisilicon.com

The trip points are checked one by one with multiple condition
branches where one condition is enough to disable the trip point.

Merge all these conditions in a single 'OR' statement.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201027013743.62392-1-bernard@vivo.com

[dlezcano] Changed patch description

Since the power actor section has one function power_actor_set_power()
move it into Intelligent Power Allocation (IPA). There is no other user
of that helper function. It would also allow to remove the check of
cdev_is_power_actor() because the code which calls it in IPA already does
the needed check. Make the function static since only IPA use it.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-5-lukasz.luba@arm.com

Since the Intelligent Power Allocation (IPA) uses different way to get
minimum and maximum power for a given cooling device, the helper functions
are not needed. There is no other code which uses them, so remove the
helper functions.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-4-lukasz.luba@arm.com

The thermal cooling device specified in DT might be instantiated for
a thermal zone trip point with a limited set of OPPs to operate on. This
configuration should be supported by Intelligent Power Allocation (IPA),
since it is a standard for other governors. Change the code and allow IPA
to get power value of lower and upper bound set for a given cooling
device.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-3-lukasz.luba@arm.com

The upper and lower limits of thermal throttle state in the
DT do not apply to the Intelligent Power Allocation (IPA) governor.
Add the clamping for cooling device upper and lower limits in the
power_actor_set_power() used by IPA.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201007024332.30322-1-michael.kao@mediatek.com

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types