ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices.  QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.

ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.

ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.

Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.

The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.

The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:

https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52

The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>

ath.git patches for v6.2. Major changes:

ath10k

* store WLAN firmware version in SMEM image table

For SDIO/USB interface, since the tranferring speed is slower than
that in PCIE, it may have race condition when the driver sets down
H2C command to the FW.

In the function rtw_fw_send_h2c_command, before the patch, box_reg
is written first, then box_ex_reg is written. FW starts to work and
fetch the value of box_ex_reg,  when the most significant byte of
box_reg(4 bytes) is written. Meanwhile, for SDIO/USB interface,
since the transferring speed is slow, the driver is still in writing
the new value of box_ex_reg through the bus, and FW may get the
wrong value of box_ex_reg at the moment.

To prevent the above driver/FW racing situation, box_ex_reg is
written first then box_reg. Furthermore, it is written in 4 bytes at
a time, instead of written in one byte one by one. It can increase
the speed for SDIO/USB interface.
Signed-off-by: Ji-Pin Jou <neo_jou@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221124064442.28042-1-pkshih@realtek.com

Commit 399500da ("ssb: pick PCMCIA host code support from b43 driver")
removes the config B43_PCMCIA.

Clean up the last reference to this removed config B43_PCMCIA in the
b43_print_driverinfo() function.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221122131248.23738-1-lukas.bulwahn@gmail.com

Commit a8b5aef2 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width")
introduced a line where the pointer returned by ieee80211_find_sta() is
used after rcu_read_unlock().

Move rcu_read_unlock() a bit lower to fix this.

Fixes: a8b5aef2 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3c82ad09-7593-3be1-1d2c-e58505fb43cb@gmail.com

urbs does not be freed in exception paths in __lf_x_usb_enable_rx().
That will trigger memory leak. To fix it, add kfree() for urbs within
"error" label. Compile tested only.

Fixes: 68d57a07 ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221119051900.1192401-1-william.xuanziyang@huawei.com

Zero-length arrays are deprecated[1] and are being replaced with
flexible array members in support of the ongoing efforts to tighten the
FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing
with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3.

Replace zero-length array with flexible-array member.

This results in no differences in binary output.

[1] https://github.com/KSPP/linux/issues/78

Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221118211146.never.395-kees@kernel.org

In a SoC based solution, it would be useful to know the versions of the
various binary firmware blobs the system is running on. On a QCOM based
SoC, this info can be obtained from socinfo debugfs infrastructure. For
this to work, respective subsystem drivers have to export the firmware
version information to an SMEM based version information table.

Having firmware version information at one place will help quickly
figure out the firmware versions of various subsystems on the device
instead of going through builds/logs in an event of a system crash.

Fill WLAN firmware version information in SMEM version table to be
printed as part of socinfo debugfs infrastructure on a Qualcomm based
SoC.

This change is applicable only for SNOC/QMI based targets.

Example:
cat /sys/kernel/debug/qcom_socinfo/cnss/name
QC_IMAGE_VERSION_STRING=WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221117180534.2267-1-quic_youghand@quicinc.com

Zero-length arrays are deprecated[1] and are being replaced with
flexible array members in support of the ongoing efforts to tighten the
FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing
with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3.

Replace zero-length array with flexible-array member.

This results in no differences in binary output (most especially because
struct pda_antenna_gain is unused). The struct is kept for future
reference.

[1] https://github.com/KSPP/linux/issues/78

Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221118234240.gonna.369-kees@kernel.org

The index RTW89_PHYSTS_BITMAP_NUM is not a valid physts IE page.
So, fix the check condition.

Fixes: eb4e52b3 ("rtw89: fix incorrect channel info during scan")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221118042322.26794-1-pkshih@realtek.com

During doing change_interface(), hardware is power-off, so some components
are inaccessible and return error. This causes things unexpected, and we
don't have a warning message for that. So, ignore some IO operations in
this situation, and add a warning message to indicate something wrong.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117085235.53777-1-pkshih@realtek.com

There are some registers for transmit waveform control, two of them used
in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls
whether to apply band edge filter to transmit waveform. TX_SHAPE controls
whether to apply triangular mask to transmit waveform. It is found for
some chip, these two should be turned off during OFDMA UL traffic for
better performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-3-pkshih@realtek.com

Add macro to get FD(frequency domain) CFO field from ie_type 1, and correct
the naming for preamble CFO field. Each IC could assign the CFO source to
either FD CFO or preamble CFO in chip_info. Based on the suggestion from HW
designer, rtw8852b and its derived versions will have better CFO tracking
performance with FD CFO.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-2-pkshih@realtek.com

When coexistence mechanism is under free-run mode, it could adjust WiFi
and BT TX power to avoid interference with each other. For other cases,
it should keep original TX power from regular predefined tables, so
set correct values to 255 for these cases.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117061832.42057-1-pkshih@realtek.com

Prefer struct_size() over open-coded versions of idiom:

sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count

where count is the max number of items the flexible array is supposed to
contain.

In this particular case, in the open-coded version sizeof(typeof-flex-array-elements)
is implicit in _count_ because the type of the flex array data is u8:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h:941:
 941 struct brcmf_dload_data_le {
 942         __le16 flag;
 943         __le16 dload_type;
 944         __le32 len;
 945         __le32 crc;
 946         u8 data[];
 947 };

Link: https://github.com/KSPP/linux/issues/160Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/41845ad3660ed4375f0c03fd36a67b2e12fafed5.1668548907.git.gustavoars@kernel.org

One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct brcmf_dload_data_le.

Important to mention is that doing a build before/after this patch results
in no binary output differences.

This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines
on memcpy() and help us make progress towards globally enabling
-fstrict-flex-arrays=3 [1].

Link: https://github.com/KSPP/linux/issues/230
Link: https://github.com/KSPP/linux/issues/79
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/905f5b68cf93c812360d081caae5b15221db09b6.1668548907.git.gustavoars@kernel.org

Prefer struct_size() over open-coded versions of idiom:

sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count

where count is the max number of items the flexible array is supposed to
contain.

Also, use array_size() in call to memcpy().

Link: https://github.com/KSPP/linux/issues/160Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/de0226a549c8d000d8974e207ede786220a3df1a.1668466470.git.gustavoars@kernel.org

One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct brcmf_gscan_config.

Important to mention is that doing a build before/after this patch results
in no binary output differences.

This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines
on memcpy() and help us make progress towards globally enabling
-fstrict-flex-arrays=3 [1].

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/241
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7694550aa9a2753a73a687f61af9441c8cf52fd7.1668466470.git.gustavoars@kernel.org

David Howells says:

====================
rxrpc: Fix oops and missing config conditionals

The patches that were pulled into net-next previously[1] had some issues
that this patchset fixes:

 (1) Fix missing IPV6 config conditionals.

 (2) Fix an oops caused by calling udpv6_sendmsg() directly on an AF_INET
     socket.

 (3) Fix the validation of network addresses on entry to socket functions
     so that we don't allow an AF_INET6 address if we've selected an
     AF_INET transport socket.

Link: https://lore.kernel.org/r/166794587113.2389296.16484814996876530222.stgit@warthog.procyon.org.uk/ [1]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan reported a new warning after my recent patch:

New smatch warnings:
net/core/dev.c:6409 napi_disable() error: uninitialized symbol 'new'.

Indeed, we must first wait for STATE_SCHED and STATE_NPSVC to be cleared,
to make sure @new variable has been initialized properly.

Fixes: 4ffa1d1c ("net: adopt try_cmpxchg() in napi_{enable|disable}()")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "pkt" was supposed to have been deleted in a previous patch.  It
leads to an uninitialized variable bug.

Fixes: 72f0c6fb ("rxrpc: Allocate ACK records at proposal and queue for transmission")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The error handling for if skb_copy_bits() fails was accidentally deleted
so the rxkad_decrypt_ticket() function is not called.

Fixes: 5d7edbc9 ("rxrpc: Get rid of the Rx ring")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of cpu_relax in mtk_pending_work routine since MTK_RESETTING is
set only in mtk_pending_work() and it runs holding rtnl lock
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restore user configured MTU running mtk_hw_init() during tx timeout routine
since it will be overwritten after a hw reset.
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 9ea4d311 ("net: ethernet: mediatek: add the whole ethernet reset into the reset process")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Carpenter reported that Smatch found an instance where a pointer
which had previously been assumed could be null (as indicated by a
null check) was later dereferenced without a similar check.

In practice this doesn't lead to a problem because currently the
pointers used are all non-null.  Nevertheless this patch addresses
the reported problem.

In addition, I spotted another bug that arose in the same commit.
When the command to initialize a routing table memory region was
added, the number of entries computed for the non-hashed table
was wrong (it ended up being a Boolean rather than the count
intended).  This bug is fixed here as well.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/kernel-janitors/Y3OOP9dXK6oEydkf@kiliTested-by: Caleb Connolly <caleb.connolly@linaro.com>
Fixes: 5cb76899 ("net: ipa: reduce arguments to ipa_table_init_add()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-next-2022-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v6.2

Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.

Major changes:

ath11k

* support configuring channel dwell time during scan

rtw89

* new dynamic header firmware format support

* Wake-over-WLAN support

rtl8xxxu

* enable IEEE80211_HW_SUPPORT_FAST_XMIT
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: support vrf processing

This patchset adds the VRF processing in SCTP. Simliar to TCP/UDP,
it includes socket bind and socket/association lookup changes.

For socket bind change, it allows sockets to bind to a VRF device
and allows multiple sockets with the same IP and PORT to bind to
different interfaces in patch 1-3.

For socket/association lookup change, it adds dif and sdif check
in both asoc and ep lookup in patch 4 and 5, and when binding to
nodev, users can decide if accept the packets received from one
l3mdev by setup a sysctl option in patch 6.

Note with VRF support, in a netns, an association will be decided
by src ip + src port + dst ip + dst port + bound_dev_if, and it's
possible for ss to have:

  State       Local Address:Port      Peer Address:Port
   ESTAB     192.168.1.2%vrf-s1:1234
   `- ESTAB   192.168.1.2%veth1:1234   192.168.1.1:1234
   ESTAB     192.168.1.2%vrf-s2:1234
   `- ESTAB   192.168.1.2%veth2:1234   192.168.1.1:1234

See the selftest in patch 7 for more usage.

Also, thanks Carlo for testing this patch series on their use.

v1->v2:
  - In Patch 5, move sctp_sk_bound_dev_eq() definition to net/sctp/
    input.c to avoid a build error when IP_SCTP is disabled, as Paolo
    suggested.
  - In Patch 7, avoid one sleep by disabling the IPv6 dad, and remove
    another sleep by using ss to check if the server's ready, and also
    delete two unncessary sleeps in sctp_hello.c, as Paolo suggested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds 12 small test cases: 01-04 test for the sysctl
net.sctp.l3mdev_accept. 05-10 test for only binding to a right
l3mdev device, the connection can be created. 11-12 test for
two socks binding to different l3mdev devices at the same time,
each of them can process the packets from the corresponding
peer. The tests run for both IPv4 and IPv6 SCTP.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add sysctl net.sctp.l3mdev_accept to allow
users to change the pernet global l3mdev_accept.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch at first adds a pernet global l3mdev_accept to decide if it
accepts the packets from a l3mdev when a SCTP socket doesn't bind to
any interface. It's set to 1 to avoid any possible incompatible issue,
and in next patch, a sysctl will be introduced to allow to change it.

Then similar to inet/udp_sk_bound_dev_eq(), sctp_sk_bound_dev_eq() is
added to check either dif or sdif is equal to sk_bound_dev_if, and to
check sid is 0 or l3mdev_accept is 1 if sk_bound_dev_if is not set.
This function is used to match a association or a endpoint, namely
called by sctp_addrs_lookup_transport() and sctp_endpoint_is_match().
All functions that needs updating are:

sctp_rcv():
  asoc:
  __sctp_rcv_lookup()
    __sctp_lookup_association() -> sctp_addrs_lookup_transport()
    __sctp_rcv_lookup_harder()
      __sctp_rcv_init_lookup()
         __sctp_lookup_association() -> sctp_addrs_lookup_transport()
      __sctp_rcv_walk_lookup()
         __sctp_rcv_asconf_lookup()
           __sctp_lookup_association() -> sctp_addrs_lookup_transport()

  ep:
  __sctp_rcv_lookup_endpoint() -> sctp_endpoint_is_match()

sctp_connect():
  sctp_endpoint_is_peeled_off()
    __sctp_lookup_association()
      sctp_has_association()
        sctp_lookup_association()
          __sctp_lookup_association() -> sctp_addrs_lookup_transport()

sctp_diag_dump_one():
  sctp_transport_lookup_process() -> sctp_addrs_lookup_transport()
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add skb_sdif function in struct sctp_af to get the enslaved device
for both ipv4 and ipv6 when adding SCTP VRF support in sctp_rcv in
the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_get_port_local(), when binding to IP and PORT, it should
also check sk_bound_dev_if to match listening sk if it's set by
SO_BINDTOIFINDEX, so that multiple sockets with the same IP and
PORT, but different sk_bound_dev_if can be listened at the same
time.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When binding to an ipv6 address, it calls ipv6_chk_addr() to check if
this address is on any dev. If a socket binds to a l3mdev but no dev
is passed to do this check, all l3mdev and slaves will be skipped and
the check will fail.

This patch is to pass the bound_dev to make sure the devices under the
same l3mdev can be returned in ipv6_chk_addr(). When the bound_dev is
not a l3mdev or l3slave, l3mdev_master_dev_rcu() will return NULL in
__ipv6_chk_addr_and_flags(), it will keep compitable with before when
NULL dev was passed.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After binding to a l3mdev, it should use the route table from the
corresponding VRF to verify the addr when binding to an address.

Note ipv6 doesn't need it, as binding to ipv6 address does not
verify the addr with route lookup.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix duplicate check on polling timeout.

Fixes: 1efa9bfe ("net: libwx: Implement interaction with firmware")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following 1b16b3fd ("net: phy: mscc: macsec: clear encryption keys when freeing a flow"),
go one step further and instead of calling memzero_explicit on the key
when freeing a flow, simply not copy the key in the first place as it's
only used when a new flow is set up.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: change GSI firmware load specification

Currently, GSI firmware must be loaded for IPA before it can be
used--either by the modem, or by the AP.  New hardware supports a
third option, with the bootloader taking responsibility for loading
GSI firmware.  In that case, neither the AP nor the modem needs to
do that.

The first patch in this series deprecates the "modem-init" Device
Tree property in the IPA binding, using a new "qcom,gsi-loader"
property instead.  The second and third implement logic in the code
to support either the "old" or the "new" way of specifying how GSI
firmware is loaded.

The last two patches implement a new value for the "qcom,gsi-loader"
property.  If the value is "skip", neither the AP nor modem needs to
load the GSI firmware.  The first of these patches implements the
change in the IPA binding; the second implements it in the code.
====================

Link: https://lore.kernel.org/r/20221116073257.34010-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Define a new value "skip" for the "qcom,gsi-loader" Device Tree
property.  If used, it indicates that neither the AP nor the modem
need to load GSI firmware (because it has already been loaded--for
example by the boot loader).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new enumerated value to those defined for the qcom,gsi-loader
property.  If the qcom,gsi-loader is "skip", the GSI firmware will
already be loaded, so neither the AP nor modem is required to load
GSI firmware.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce a new way of specifying how the GSI firmware gets loaded
for IPA.  Currently, this is indicated by the presence or absence of
the Boolean "modem-init" Device Tree property.  The new property
must have a value--either "self" or "modem"--which indicates whether
the AP or modem is the GSI firmware loader, respectively.

For legacy systems, the new property will not exist, and the
"modem-init" property will be used.  For newer systems, the
"qcom,gsi-loader" property *must* exist, and must have one of the
two prescribed values.  It is an error to have both properties
defined, and it is an error for the new property to have an
unrecognized value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>