The i40e driver attempts to display the UDP tunnel name by doing a check
against the type, where for non-zero types we use "vxlan" and for zero
type we use "geneve". This is not future proof, because if new tunnel
types get added, we'll incorrectly label them. It also depends on the
value of UDP_TUNNEL_TYPE_GENEVE == 0, which is brittle.

Instead, replace this with a function that can return a constant string
depending on the type. For now we'll use "unknown" for types we don't
know about, and we can expand this in the future if new types get added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Compiler reported several places where driver compared
signed and unsigned types.  Cast or change the types to remove
the warnings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This just reorders some local vars and makes the code flow
clearer.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The compiler warned on an oddly indented bit of code, and when
investigating that, noted that the functions themselves had
an odd flow. The if condition was checked, and would exclude
a call to AQ, but then the aq_ret would be checked unconditionally
which just looks really weird, and is likely to cause objections.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As it turns out there was only a small set of errors
on 32 bit, and we just needed to be using the right calls
for dealing with timespec64 variables.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There are some rare cases where the release resource call will return an
admin Q timeout. In these cases the code needs to try to release the
resource again until it succeeds or it times out.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During certain events such as a CORER, multiple devices will run a work
task to handle some cleanup. This can cause issues due to
a single-threaded workqueue which can mean that a device doesn't cleanup
in time. Prevent this by removing the single-threaded restriction on the
module workqueue. This avoids the need to add more complex yielding
logic in our service task routine. This is also similar to what other
drivers such as fm10k do.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem found in systems when entering
S4 state.  This patch fixes the problem by ensuring that
the misc vector's IRQ is disabled as well.  Without this
patch a stack trace can be seen upon entering S4 state.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix incorrect variable assignment.
Based on line 1511: aq_ret = I40_ERR_PARAM; the correct variable to be
used in this instance is aq_ret instead of ret. Also, variable ret is
updated at line 1602 just before return, so assigning a value to this
variable in this code block is useless.

Addresses-Coverity-ID: 1397693
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Michael Chan says:

====================
bnxt_en: Fix kbuild errors and rename phys_port_name.

Fix 2 more kbuild errors (the first one already fixed by DaveM), and rename
the physical port name.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the phys_port_name for the external physical port to be in
"pA" format and that of VF-rep to be in "pCvfD" format as
suggested by Jakub Kicinski.

Fixes: c124a62f ("bnxt_en: add support for port_attr_get and get_phys_port_name")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes the build error:
‘struct net_device’ has no member named ‘switchdev_ops’
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c124a62f ("bnxt_en: add support for port_attr_get and and get_phys_port_name")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And define empty functions in bnxt_vfr.h when CONFIG_BNXT_SRIOV is not
defined.

This fixes build error when CONFIG_BNXT_SRIOV is switched off:
>> drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c:165:16: error: 'struct
>> bnxt' has no member named 'sriov_lock'
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 4ab0c6a8 ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
network related warning fixes

Various fixes for warnings in network code and drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable owned_by_user is always set, but only used
when kernel is configured with LOCKDEP enabled.

Get rid of the warning by moving the code to put the call
to owned_by_user into the the rcu_protected call.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

warning: ‘recent_old_fops’ defined but not used
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

warning: variable ‘netdev’ set but not used
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a couple of warnings where variable ‘txq’ set but not used
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>v, i);
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes warning because location is u32 and can never be netative
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a netdev (PF netdev or representor) is opened or closed, set the
physical port config bit appropriately - which powers UP/DOWN the PHY
module for the physical interface.

The PHY is powered first in the HW/FW configuration step when opening
the netdev and again last in the HW/FW configuration step when closing
the netdev.

This is only applicable when there is a physical port associated with
the netdev and if the NSP support this. Otherwise we silently ignore
this step.

The 'nfp_eth_set_configured' can actually return positive values -
updated the function documentation appropriately.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

we can use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
1. drivers/net/appletalk/ipddp.c
2. drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.c

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested by Jakub Kicinski.

Fixes: c124a62f ("bnxt_en: add support for port_attr_get and and get_phys_port_name")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On resume, the ibmvnic driver will fail to resume normal operation.
The main crq gets closed on suspend by the vnic server and doesn't get
reopened again as the interrupt for the transport event that would reset
the main crq comes in after the driver has been suspended.

This patch resolves the issue by removing the calls to kick the receive
interrupts handlers and instead directly invoking the main crq interrupt
handler. This will ensure that we see the transport event necessary to
properly resume the driver.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
netvsc: minor fixes

This fixes fallout from previous patch related to RTNL and RCU
annotaiton. Also one patch sent to wrong list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This value has been calculated in rndis_device_attach since 4.11.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since these files use rtnl_derefernce make sure and include rtnetlink.h
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of channels returned by rndis_filter_device_add maybe
less than the number requested. Therefore set correct real
number of queues.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In interrupt handler, prefetch the first incoming ring element
so that it is in cache by the time NAPI poll gets to it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This condition already uses an object of type ipv6hdr in the line above.
Use the object directly instead of calling ipv6_hdr
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove accidental rtnl_unlock from earlier testing.

Fixes: 3962981f ("netvsc: add rtnl annotations in rndis")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

This series includes updating the firmware interface, adding
methods to get and set VEPA/VEB bridge modes, some minor DCBX and ETS
refinements, and 3 patches from Sathya Perla to implement initial
VF representors for SRIOV switching.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the switchdev_port_attr_get() and
ndo_get_phys_port_name() methods for the PF and the VF-reps.
Using this support a user application can deduce that the PF
(when in the ESWITCH_SWDEV mode) and it's VF-reps form a switch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the RX/TX and a simple netdev implementation
for VF-reps. The VF-reps use the RX/TX rings of the PF. For each VF-rep
the PF driver issues a VFR_ALLOC FW cmd that returns "cfa_code"
and "cfa_action" values. The FW sets up the filter tables in such
a way that VF traffic by default (in absence of other rules)
gets punted to the parent PF. The cfa_code value in the RX-compl
informs the driver of the source VF. For traffic being transmitted
from the VF-rep, the TX BD is tagged with a cfa_action value that
informs the HW to punt it to the corresponding VF.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is a part of a patch-set that introduces support for
VF-reps in the bnxt_en driver. The driver registers eswitch mode
get/set methods with the devlink interface that allow a user to
enable SRIOV switchdev mode. When enabled, the driver registers
a VF-rep netdev object for each VF with the stack. This can
essentially bring the VFs unders the management perview of the
hypervisor and applications such as OVS.

The next patch in the series, adds the RX/TX routines and a slim
netdev implementation for the VF-reps.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In addition to the ETS weight, older firmware also requires the min_bw
parameter to be set for it to work properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report DCB_CAP_DCBX_LLD_MANAGED only if the firmware DCBX agent is enabled
and running for PF or VF.  Otherwise, if both LLDP and DCBX agents are
disabled in firmware, we report DCB_CAP_DCBX_LLD_HOST and allow host
IEEE DCB settings.  This patch refines the current logic in the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For debugging purpose, it is sometimes useful to disable periodic
port statistics updates, so that the firmware logs will not be
filled with statistics update messages.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of duplicating the logic multiple times.  Also, it is unnecessary
to zero the buffer in .get_ethtool_stats() because it is already zeroed
by the caller.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To allow users to set the hardware bridging mode to VEB or VEPA.  Only
single function PF can change the bridging mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>