- 10 May, 2015 2 commits
-
-
Maxime Ripard authored
A few lines in our DTSIs are over the 80 characters limit, making checkpatch complain about that. If possible (and relevant), wrap these lines to 80 characters. Signed-off-by:Maxime Ripard <maxime.ripard@free-electrons.com>
-
Maxime Ripard authored
The FSF address triggers a warning on checkpatch, saying that the FSF license is already present in the Linux source code, and that it has already changed in the past. Remove it from our DT, as suggested. Signed-off-by:
-
- 02 May, 2015 1 commit
-
-
Marcus Cooper authored
Currently none of the target boards nor the driver supports IR TX. However this pin is used in a few instances as a GPIO. Split the pin ctrl descriptions so that only the IR RX is configured to be used. Signed-off-by:
Marcus Cooper <codekipper@gmail.com> Signed-off-by:
-
- 29 Apr, 2015 1 commit
-
-
Marcus Cooper authored
The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash, a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles, a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV. This patch adds basic support for the device, more information can be found here (http://linux-sunxi.org/MK808C). Signed-off-by:
-
- 27 Apr, 2015 36 commits
-
-
Chen-Yu Tsai authored
On sun6i we already have PLL6 as AHB1 clock's parent. However this was previously set in the dma controller node, which takes effect when the dma controller is probed. We want this to take effect as soon as possible, so hrtimer rate calculation is correct, and to be sure the AHB1 clock rate remains as stable as possible. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Chen-Yu Tsai authored
The clock driver now supports a muxable ahb clock. Update the dtsi with the proper compatible and add the new parent clocks. This also adds the new pll6/4 output for pll6 on sun7i-a20. The output is not used on sun4/5i. Also use assigned-clocks to reparent ahb to pll6. We want ahb to have a stable, non-changing clock rate. cpu/axi clock rate changes as a result of newly added cpufreq support. Signed-off-by:
-
Hans de Goede authored
The Jesurun Q5 has a black plastic casing with the approximate dimensions of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to power) and an programmable green led. On the board there is also an unpopulated IR receiver and the UART. The devices is equipped with an AXP209 PMU. For more details see: http://linux-sunxi.org/Jesurun_Q5Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
Add a node for the chipone-icn8318 touchscreen found on the Utoo P66 tablet. Signed-off-by:
-
Hans de Goede authored
The Orangepi mini is a development board using the Allwinner A20 SoC, with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports, ir receiver and a headphones jack. Also see: http://linux-sunxi.org/Xunlong_Orange_Pi_Mini http://www.orangepi.org/Signed-off-by:
-
Hans de Goede authored
The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM, microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports, ir receiver and a headphones jack. Also see: http://linux-sunxi.org/Xunlong_Orange_Pi http://www.orangepi.org/Signed-off-by:
-
Maxime Ripard authored
The A20 has a few SRAM that can be mapped either to a device or to the CPU, with the mapping being controlled by a SRAM controller. Since most of the time these SRAM won't be accessible by the CPU, we can't use the mmio-sram driver and compatible. Signed-off-by:
-
Hans de Goede authored
The A13 / A10s has a few SRAM that can be mapped either to a device or to the CPU, with the mapping being controlled by a SRAM controller. Since most of the time these SRAM won't be accessible by the CPU, we can't use the mmio-sram driver and compatible. Signed-off-by:
-
Hans de Goede authored
The A10 has a few SRAM that can be mapped either to a device or to the CPU, with the mapping being controlled by a SRAM controller. Since most of the time these SRAM won't be accessible by the CPU, we can't use the mmio-sram driver and compatible. Signed-off-by:
-
Hans de Goede authored
The eMMC on the A13 based Utoo-P66 tablet does not properly support hpi, and trying to enable it results in the eMMC not working, so add a child-node describing the eMMC, and set the broken-hpi property on it. Signed-off-by:
-
Chen-Yu Tsai authored
Add enable-method property to enable SMP support. Signed-off-by:
-
Chen-Yu Tsai authored
The core temperature sensor now supports thermal zones. Add a thermal zone mapping for the cpus with passive cooling (cpufreq throttling). Signed-off-by:
-
Chen-Yu Tsai authored
The cpu core is clocked from the "cpu" clock. Add a reference to it in the first cpu node. Also add "cpu0" label to the node. The operating points were taken from the a list compiled by Maxime Ripard, which is based on A31 FEX files from the sunxi-boards repository. Not all boards have the same settings. The settings in this patch are the ones shared by A/B/C revisions, plus the default clock setting from u-boot. Signed-off-by:
-
Maxime Ripard authored
Add UART aliases and stdout-path property for all the Allwinner boards so that we won't have to rely on the bootargs' console= value, while working with legacy bootloaders. While we're at it, also remove the mentions of earlyprintk in the bootargs, that will remove our default bootargs entirely, and allow the kernel to boot on a system even if DEBUG_LL is configured for another system. Signed-off-by: -
Hans de Goede authored
Remove the unused usb1_vbus_pin_csq908 node (vbus is always on on the cs908), and sort the remaining nodes alphabetically. Signed-off-by:
-
Chen-Yu Tsai authored
Since the phy core already supports specifying a regulator to handle during power up/down, it was decided to drop the regulator support in the sun9i usb phy driver. This patch switches the DT to the core bindings. This and the phy driver would be in the same release and should not be a problem as far as DT stability goes. Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Chen-Yu Tsai authored
The A80 SoC has the architected timer, but the existing firmware from Allwinner does not set CNTFRQ at all. Signed-off-by:
-
Chen-Yu Tsai authored
The A23 SoC has the architected timer, but the existing firmware from Allwinner does not set CNTFRQ at all. Signed-off-by:
-
Chen-Yu Tsai authored
The Hummingbird A31 has an AMPAK AP6210 WiFi+Bluetooth module. The WiFi part is a BCM43362 IC connected to MMC1 in the A31 SoC via SDIO. The IC also takes a power enable signal via GPIO. This is supported with the new power sequencing bindings. The WiFi module supports out-of-band interrupt signaling via GPIO, but this is not enabled yet. Signed-off-by:
-
Chen-Yu Tsai authored
mmc1 is used to connect to the WiFi chip on the Hummingbird A31. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Sometimes we need to specify non-probably information for sdio devices in the devicetree, this is done through child nodes addressed by the reg property, whereby the reg property refers to the sdio function number, see; Documentation/devicetree/bindings/mmc/mmc.txt This commit adds the necessary address- and size-cells properties to the mmc controller nodes in the dtsi files, so that dts files needing such a child node do not need to specify these themselves. Signed-off-by:
-
Chen-Yu Tsai authored
This patch adds the AXP221 regulators. Only the ones directly used on the board are added. Signed-off-by:
-
Chen-Yu Tsai authored
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller. Signed-off-by:
-
Chen-Yu Tsai authored
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller. Signed-off-by:
-
Boris BREZILLON authored
The p2wi controller has only one possible pinmux setting. Use it by default in the dtsi, instead of having to set it in each board's dts. Signed-off-by:
Boris BREZILLON <boris.brezillon@free-electrons.com> [wens@csie.org: reformat commit title; rename p2wi pins and use as default] Signed-off-by:
-
Tyler Baker authored
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This device tree has been derived from the sun9i-a80-optimus.dts as they are very similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM definitions will need to be updated in the future. [1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdfSigned-off-by:
Tyler Baker <tyler.baker@linaro.org> Signed-off-by:
-
Aleksei Mamlin authored
This patch adds vendor-prefix for Wexler. WEXLER trademark owned by AVIRSA Electronics, a member of the diversified holding AVIRSA. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Aleksei Mamlin authored
This patch add support for Wexler TAB7200 tablet. The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480), capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot, mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port. Signed-off-by:
-
Hans de Goede authored
The touchscreen controller in the A13 and later has a different temperature curve than the one in the original A10, change the compatible for the A13 and later so that the kernel will use the correct curve. Reported-by:
Tong Zhang <lovewilliam@gmail.com> Signed-off-by:
-
Tyler Baker authored
Add a cubietech vendor prefix, as it is missing. The cubietruck, cubieboard2, and cubieboard all already reference this prefix. Signed-off-by:
-
Hans de Goede authored
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips lcd screen, 512MB RAM & 4GB emmc. Signed-off-by:
-
Hans de Goede authored
The auxtek-t004: http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash, toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and a 2 micro-usb receptacles, one for power and one for USB OTG. The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq support for it. Signed-off-by:
-
Hans de Goede authored
Add A13 mmc2 pinmux settings, note these are for a 8bit bus. Signed-off-by:
-
Hans de Goede authored
The A13 and the A10s use the same die (this has been confirmed by Allwinner), as such there is no need to differentiate between the ehci/ohci parts of both, the only reasons there were different allwinner,sun5i-a*-foo compatible between these 2 parts is costemetically and because we could when we still had 2 completely different dtsi files. The allwinner,sun5i-a*-foo compatible strings are not used for binding at all, the actual driver binds to the generic-?hci compatible, so we can safely remove this cosmetical difference and simplify the dtsi files. Signed-off-by:
-
Hans de Goede authored
Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet. Signed-off-by:
-
