- 19 Sep, 2012 3 commits
-
-
Thierry Reding authored
Power management callbacks defined by SIMPLE_DEV_PM_OPS are only used if the PM_SLEEP Kconfig symbol has been defined. If not, the compiler will complain about them being unused. However, since the callback for this driver doesn't do anything it can just as well be dropped. Signed-off-by:
Thierry Reding <thierry.reding@avionic-design.de> Acked-by:
Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by:
Chris Ball <cjb@laptop.org>
-
Kyungsik Lee authored
It is expected that Extended CSD register (the size of this register is larger than CID/CSD) will be referenced more frequently as more fields have been added to Extended CSD and it seems that it is not a good option to double the memory used. This patch is intended to avoid the use of bounce buffer for reading Extended CSD register in mmc_send_cxd_data(). It will provide a better performance gain by removing memcpy() overhead for a half KiB and a redundant bounce buffer allocated repeatedly at the cost of providing DMA-capable buffer from upper caller (but on-stack buffer is allowed with no performance gain). Signed-off-by:
Kyungsik Lee <kyungsik.lee@lge.com> Reviewed-by:
Venkatraman S <svenkatr@ti.com> Signed-off-by:
-
Chris Ball authored
Tested on OLPC XO-4/MMP3, where the card detection pin for one of the controllers is a sideband GPIO. The third cell in the cd-gpios property controls whether the GPIO is active high/active low. (Also, pass host_caps2 through from platdata to the mmc host.) Acked-by:
Haojian Zhuang <haojian.zhuang@gmail.com> [kliu5@marvell.com: Compile fix] Signed-off-by:
-
- 11 Sep, 2012 1 commit
-
-
Chris Ball authored
mmc_gpio_request_ro() doesn't store the requested gpio in ctx->ro_gpio. As a result, subsequent calls to mmc_gpio_get_ro() will always fail with -ENOSYS because the gpio number isn't available to that function. Cc: stable <stable@vger.kernel.org> Acked-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
- 04 Sep, 2012 36 commits
-
-
Sachin Kamat authored
module_pci_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Acked-by:
Harald Welte <laforge@gnumonks.org> Signed-off-by:
-
Sachin Kamat authored
module_pci_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by:
-
Sachin Kamat authored
module_pci_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by:
-
Sachin Kamat authored
module_spi_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by:
-
Jingoo Han authored
This patch fixes the checkpatch error and warnings listed below: ERROR: return is not a function, parentheses are not required WARNING: Prefer pr_err(... to printk(KERN_ERR, ... WARNING: quoted string split across lines WARNING: line over 80 characters WARNING: braces {} are not necessary for single statement blocks Signed-off-by:Jingoo Han <jg1.han@samsung.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
-
Johan Rudholm authored
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init. Signed-off-by:
Johan Rudholm <johan.rudholm@stericsson.com> Acked-by:
Ulf Hansson <ulf.hansson@linaro.org> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jaehoon Chung authored
Fixed the below message. WARNING: drivers/mmc/host/built-in.o(.text+0x5ee8): Section mismatch in reference from the function dw_mci_probe() to the function .init.text:dw_mci_init_slot() The function dw_mci_probe() references the function __init dw_mci_init_slot(). This is often because dw_mci_probe lacks a __init annotation or the annotation of dw_mci_init_slot is wrong Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Will Newton <will.newton@imgtec.com> Signed-off-by:
-
Joseph Lo authored
When compiling a kernel that supports only Tegra30 and not Tegra20, the SDHCI driver will fail to compile since the of_match_device() failure fallback code unconditinally references soc_data_tegra20, which is only compiled in when Tegra20 support is enabled. In Kernel 3.7, both Tegra20 and Tegra30 will only support booting using device tree, Hence, there is never a need to fall back to using soc_data_tegra20 if of_mach_device() fails. Instead, make this case an error. This removes the reference to soc_data_tegra20, and hence solves the compile failure. Signed-off-by:
Joseph Lo <josephl@nvidia.com> Tested-by:
Stephen Warren <swarren@wwwdotorg.org> Signed-off-by:
-
Chris Ball authored
Signed-off-by: -
Venkatraman S authored
I can continue to look after this driver. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Venkatraman S authored
Consolidate the duplicated code around the handling of CMD_TIMEOUT, CMD_CRC, DATA_TIMEOUT, DATA_CRC and CARD_ERR handling into a single function. This generally shrinks code bloat, but is also required for implementing software based guard timers. Signed-off-by:
-
Venkatraman S authored
Flushing spurious IRQs from HSMMC IP is done twice in omap_hsmmc_irq and omap_hsmmc_do_irq. Consolidate them to one location. Signed-off-by:
-
Venkatraman S authored
SYSCONFIG register of HSMMC IP is managed by the omap hwmod abstraction layer. Resetting the IP and configuring the correct SYSCONFIG mode is centrally managed by hwmod. Remove code which manipulates IP reset and SYSCONFIG directly in the driver. Signed-off-by:
-
Venkatraman S authored
Some straight forward cleanup of unnecessary #include's and host variables. Some of the verbose and redundant debug messages are converted to use dev_vdbg. Signed-off-by:
-
Venkatraman S authored
The function mmc_omap_report_irq uses raw printks and the actual output was disabled by a static variable. Make the function use dev_vdbg macro and use it under the standard CONFIG_MMC_DEBUG flag. Signed-off-by:
-
Venkatraman S authored
Get rid of some unnecessary includes in the driver and a few unused variables. Signed-off-by:
-
Venkatraman S authored
ext_csd exported through debugfs is printed in reverse order (from byte 511 to 0), which causes confusion. Fix the for loop to print ext_csd in natural order. Signed-off-by:
-
Venkatraman S authored
HPI can be issued only in programming state to bring the card to transfer state. If the card is already in transfer state, doing a HPI is redundant. Fix this by adding transfer state to the list of exceptions to doing HPI and return without error. Signed-off-by:
-
Sonic Zhang authored
Without reset, SD controller may stay in disable mode, SD card can't be detected when resume from power saving mode. Signed-off-by:
Sonic Zhang <sonic.zhang@analog.com> Signed-off-by:
-
Sonic Zhang authored
mmc core suspend and resume functions had already called sdh_set_ios with proper flags. Signed-off-by:
Bob Liu <lliubbo@gmail.com> Signed-off-by:
-
Sonic Zhang authored
In BF60x RSI controller: 1) MMR read/write width differs. 2) PWR and CTL MMRs are merged to together. 3) ROD and PD_DAT3 bit masks are obsolete. 4) New RSI block size MMR is defined. 5) The definition of DMA descriptor set size is changed. 6) set_ios should powers up controller in 2 steps. In addition, this patch cleans up the spin locks. Signed-off-by:
-
Sonic Zhang authored
bf518 RSI dma doesn't work in array mode. Signed-off-by:
-
Sonic Zhang authored
Signed-off-by:
-
NeilBrown authored
1/ If regulator_get fails, return an error. This is important if it failed with EPROBE_DEFER, as the probe needs to be deferred. 2/ Don't set .set_power until the regulator has been found, or the deferred probe will not bother calling omap_hsmmc_reg_get(). Signed-off-by:
NeilBrown <neilb@suse.de> Acked-by:
Rajendra Nayak <rnayak@ti.com> Signed-off-by:
-
Julia Lawall authored
Add missing usb_free_urb on failure path after usb_alloc_urb. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @km exists@ local idexpression e; expression e1,e2,e3; type T,T1; identifier f; @@ * e = usb_alloc_urb(...) ... when any when != e = e1 when != e1 = (T)e when != e1(...,(T)e,...) when != &e->f if(...) { ... when != e2(...,(T1)e,...) when != e3 = e when forall ( return <+...e...+>; | * return ...; ) } // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Sebastian Hesselbarth authored
This patch adds device tree support and binding documentation for sdhci-dove. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com> Signed-off-by:
-
Chao Xie authored
Prepare the clock before enabling it. Signed-off-by:
Chao Xie <xiechao.mail@gmail.com> Signed-off-by:
-
Ludovic Desroches authored
Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by:
-
Philip Rakity authored
The vmmc regulator should not rely on the platform code to enable it. Expliciitly enable and disable the regulator inside the driver. Signed-off-by:
Philip Rakity <prakity@marvell.com> Signed-off-by:
-
Philip Rakity authored
On some systems the host controller does not support vccq signaling. This is supplied by a dedicated regulator (vqmmc). Add support for this regulator. Signed-off-by:
-
Jerry Huang authored
The register of eSDHC Host Controller Capabilities is not compatible with standard SDHC register, and eSDHC cannot support End Attribute in NOP ADMA descriptor. With this patch eSDHC can works in ADMA mode and performance can be improved. Signed-off-by:
Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by:
Pan Jiafei <Jiafei.Pan@freescale.com> Signed-off-by:
Jason Jin <Jason.jin@freescale.com> Acked-by:
Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by:
-
Daniel Mack authored
Signed-off-by:
Daniel Mack <zonque@gmail.com> Signed-off-by:
-
Paul Walmsley authored
After commit 26b88520 ("mmc: omap_hsmmc: remove private DMA API implementation"), the Nokia N800 here stopped booting: [ 2.086181] Waiting for root device /dev/mmcblk0p1... [ 2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000 [ 2.331451] Internal error: : 406 [#1] ARM [ 2.335784] Modules linked in: [ 2.339050] CPU: 0 Not tainted (3.6.0-rc3 #60) [ 2.344146] PC is at default_idle+0x28/0x30 [ 2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0 ... This turned out to be due to memory corruption caused by long-broken PIO code in drivers/mmc/host/omap.c. (Previously, this driver had been using DMA; but the above commit caused the MMC driver to fall back to PIO mode with an unmodified Kconfig.) The PIO code, added with the rest of the driver in commit 730c9b7e ("[MMC] Add OMAP MMC host driver"), confused bytes with 16-bit words. This bug caused memory located after the PIO transfer buffer to be corrupted with transfers larger than 32 bytes. The driver also did not increment the buffer pointer after the transfer occurred. This bug resulted in data corruption during any transfer larger than 64 bytes. Signed-off-by:
Paul Walmsley <paul@pwsan.com> Reviewed-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Ian Chen authored
For several MoviNAND eMMC parts, there are known issues with secure erase and secure trim. For these specific MoviNAND devices, we skip these operations. Specifically, there is a bug in the eMMC firmware that causes unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE enabled. References: http://forum.xda-developers.com/showthread.php?t=1644364 https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkBSigned-off-by:
Ian Chen <ian.cy.chen@samsung.com> Reviewed-by:
Namjae Jeon <linkinjeon@gmail.com> Acked-by:
-
Doug Anderson authored
The documentation for the dw_mmc part says that the low power mode should normally only be set for MMC and SD memory and should be turned off for SDIO cards that need interrupts detected. The best place I could find to do this is when the SDIO interrupt was first enabled. I rely on the fact that dw_mci_setup_bus() will be called when it's time to reenable. Signed-off-by:
Doug Anderson <dianders@chromium.org> Acked-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
-
Seungwon Jeon authored
Data transfer will be continued until all the bytes are transmitted, even if data crc error occurs during a multiple-block data transfer. This means RXDR/TXDR interrupts will occurs until data transfer is terminated. Early setting of host->sg to NULL prevents going into xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts occurs. And checking error interrupt status in the xxx_data_pio functions is no need because dw_mci_interrupt does do the same. This patch also removes it. Signed-off-by:
-
