Add hotplug support.  We have to make the interrupt handler threaded so
we can call drm_helper_hpd_irq_event().  Keeping in mind that we will
want to share the interrupt with other HDMI interface drivers (eg, audio
and CEC) put the groundwork in now for that, rather than just using
IRQF_ONESHOT.

Also, we must not call drm_helper_hpd_irq_event() until we have fully
setup the connector; keep the interrupt(s) muted until after that point.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add core imx-drm support for hotplug connector support.  We need to
setup the poll helper after we've setup the connectors; the helper
scans the connectors to determine their capabilities.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Various cleanups are possible after the previous round of changes; these
have no real functional bearing other than tidying up the code.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

It is now no longer necessary to keep this structure around; we can
allocate it upon DRM driver load and destroy it thereafter without
affecting the other components now.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This mutex doesn't protect anything anymore; get rid of it.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Since we're now operating like a conventional DRM driver, doing all
the initialisation within the driver's ->load callback, we don't
need to mess around with the mode groups - we can rely on the one
in the DRM platform code.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The core imx_drm_connector and imx_drm_encoder code is no longer
required - the connectors and encoders are all using the component
support, so we can remove this.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Now that our bind function is only ever called during the main DRM
driver ->load callback, we don't need to have the imx_drm_connector or
imx_drm_encoder abstractions anymore.  So let's get rid of it, and move
the DRM connector and encoder setup into the connector support files.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Provide two helper functions to assist with cleaning up imx-drm
connectors and encoders.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Provide a helper function to parse possible crtcs before the encoder
is registered.  The crtc mask is derived from the position of the
CRTCs registered in the drm_device.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The component helper provides us the drm_device which is being
registered.  Rather than having to reference a global in imx-drm-core,
use this to get the imxdrm device, and also use it to register the CRTC
against.

This means we never have CRTCs/encoders/connectors without the drivers
private data being accessible.

Remove the module owner field as well; this provides no protection
against the device being unbound.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

imx-fb.c doesn't need to be separate from imx-drm-core.c - all it is
doing is setting up the minimum and maximum sizes of the scanout
buffers, and setting up the mode_config function pointers.  Move the
contents into imx-drm-core.c and kill this file.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Now that we know when the components of the imx-drm subsystem will be
initialised, we can move the fbdev helper initialisation and teardown
into imx-drm-core.  This gives us the required ordering that DRM wants
in both driver load and unload methods.

We can also stop exporting the imx_drm_device_get() and
imx_drm_device_put() methods; nothing but the fbdev helper was making
use of these.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Delay publishing sysfs connector entries until all components have
initialised.  This reduces the probability of generating false hotplug
events when we're uncertain whether the driver can fully initialise.
This also pulls that code out of the individual imx-drm connector
drivers.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use the componentised device support for imx-drm.  This requires all
the sub-components and the master device to register with the component
device support.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The encoder format passed into imx_drm_crtc_panel_format*() is the
encoder format used for DRM in most cases; the HDMI encoder sets
this to none, but this is incorrect, it should be TMDS.

Since this is the case, we can pass the drm_encoder structure
directly into this function and use the supplied fields there to
configure the CRTC.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Provide a common connector mode validation function, which can be used
to limit the available modes according to other components in the
system.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The DRM core indexes vblank by number, so there's little point
maintaining a list, and have to scan the list to find the appropriate
structure.  Instead, use an array of pointers to the CRTCs.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Address the following issues:
- imx_drm_encoder_get_mux_id() searches the CRTC list for the matching
  CRTC, and returns the position within this list as the MUX programming
  value for encoders.  This is sub-optimal for two reasons:
  1. It relies upon the CRTC list not changing during the lifetime of
     the driver.
  2. It is dependent on the initialisation order of the CRTCs.

  We address (1) in this patch, leaving (2) until a better solution can
  be found, as (2) requires larger changes.

- imx_drm_encoder is unused.  Instead, pass the drm_encoder which is
  slightly more useful; all callers pass encoder->crtc as the required
  crtc, so move this inside the function.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Extracted from another patch by Fabio Estevam, this adds the DT
configuration for HDMI output on the IMX6 SoCs
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There's no point in using the clk API for this; we end up having to
violate the layering this provides.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This is nonsense; clk_round_rate() is just clk_set_rate() without the
side effect of changing the hardware.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The DI clock selection was very rudimentary: it would statically use
either the IPU internal clock or the DI external clock depending on
which "encoder" was being used.  In the case of HDMI, it would always
use the IPU clock.

Moreover, using the IPU clock resulted in fractional divisors, which
are achieved by skipping clock pulses.  This can result in the HDMI
PHY PLL being frequency modulated, and the attached device is then
unable to properly lock on to the TMDS clock.

We need at least 1% accurate and stable clocks for HDMI.

Arrange for the DI clock to be sourced from the IPU internal clock
if it can satisfy our requirements, otherwise switch to the DI
external clock and try and set the external clock to our desired
pixel clock rate.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Many of the variables for the audio clock regenerator (CTS/N) were not
initialised in any way.  The pixel rate which was being used also
wasn't being adjusted at all when the display mode is modified.

Get rid of the seaprate 'pixel_clk_rate', and use the stored pixel
clock rate instead.  Pass this desired pixel clock rate into
hdmi_set_clk_regenerator().  Collapse down hdmi_init_clk_regenerator()
since it is a copy of hdmi_set_clk_regenerator(), and pass a default
pixel clock rate.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There are a load of read-modify-write patterns to change bitfields in
various registers in this driver; provide a helper to perform this
manipulation.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Rather than manually writing each register sequentially, we can use a
loop to reduce the amount of code.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Rather than having large if() and switch() statements, provide a table
to look up the register settings for various clock rates.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes for ARM platforms.  Most are fixes for DTS
  files, mostly from DT conversion on OMAP which is still finding a few
  issues here and there.

  There's a couple of small stale code removal patches that we usually
  queue for the next release instead, but they seemed harmless enough to
  bring in now.

  Also, a fix for backlight on some PXA platforms, and a cache
  configuration fix for Tegra, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
  MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
  ARM: tegra: only run PL310 init on systems with one
  ARM: tegra: Add head numbers to display controllers
  ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
  ARM: tegra: fix RTC0 alias for Cardhu
  ARM: dove: dt: revert PMU interrupt controller node
  Documentation: dt: OMAP: Update Overo/Tobi
  ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
  ARM: dts: omap3-tobi: Use the correct vendor prefix
  ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
  ARM: OMAP2+: Remove legacy macros for zoom platforms
  ARM: OMAP2+: Remove MACH_NOKIA_N800
  ARM: dts: N900: add missing compatible property
  ARM: dts: N9/N950: fix boot hang with 3.14-rc1
  ARM: OMAP1: nokia770: enable tahvo-usb
  ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
  ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
  ARM: dts: omap3-gta04: Fix mmc1 properties.
  ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
  ARM: OMAP2+: add missing ARCH_HAS_OPP
  ...

Pull regulator fixes from Mark Brown:
 "Mostly unexciting driver fixes, plus one fix to lower the severity of
  the log message when we don't use an optional regulator - the fixes
  for ACPI system made this come up more often and it was correctly
  observed that it was causing undue concern for users"

* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: max14577: Fix invalid return value on DT parse success
  regulator: core: Change dummy supplies error message to a warning
  regulator: s5m8767: Add missing of_node_put
  regulator: s5m8767: Use of_get_child_by_name
  regulator: da9063: Bug fix when setting max voltage on LDOs 5-11

Pull timer fix from Thomas Gleixner:
 "Serialize the registration of a new sched_clock in the currently ARM
  only generic sched_clock facilty to avoid sched_clock havoc"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched_clock: Prevent callers from seeing half-updated data

Pull x86 fixes from Thomas Gleixner:

 - a bugfix which prevents a divide by 0 panic when the newly introduced
   try_msr_calibrate_tsc() fails

 - enablement of the Baytrail platform to utilize the newfangled msr
   based calibration

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: tsc: Add missing Baytrail frequency to the table
  x86, tsc: Fallback to normal calibration if fast MSR calibration fails

Pull irq fixes from Thomas Gleixner:
 "Another four fixlets to tame the ARM orion irq chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: orion: Fix getting generic chip pointer.
  irqchip: orion: clear stale interrupts in irq_startup
  irqchip: orion: use handle_edge_irq on bridge irqs
  irqchip: orion: clear bridge cause register on init

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for reported issues for 3.14-rc4

  The majority of these are for USB gadget, phy, and musb driver issues.
  And there's a few new device ids thrown in for good measure"

* tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: need to mask when writting endptflush and endptprime
  usb: musb: correct use of schedule_delayed_work()
  usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP
  usb: gadget: fix NULL pointer dereference
  usb: gadget: printer: using gadget_is_otg to check otg support at runtime
  phy: let phy_provider_register be the last step in registering PHY
  phy-core: Don't allow building phy-core as a module
  phy-core: Don't propagate -ENOSUPP from phy_pm_runtime_get_sync to caller
  phy-core: phy_get: Leave error logging to the caller
  phy,phy-bcm-kona-usb2.c: Add dependency on HAS_IOMEM
  usb: musb: correct use of schedule_delayed_work()
  usb: musb: do not sleep in atomic context
  USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8
  USB: EHCI: add delay during suspend to prevent erroneous wakeups
  usb: gadget: bcm63xx_udc: fix build failure on DMA channel code
  usb: musb: do not sleep in atomic context
  usb: gadget: s3c2410_udc: Fix build error
  usb: musb: core: Fix remote-wakeup resume
  usb: musb: host: Fix SuperSpeed hub enumeration
  usb: musb: fix obex in g_nokia.ko causing kernel panic

Pull TTY revert from Greg KH:
 "Here is a single commit, a revert of a sysfs file change that ended up
  breaking a userspace tool"

* tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "tty: Set correct tty name in 'active' sysfs attribute"

Pull staging tree fix from Greg KH:
 "Here is a single android driver fix for 3.14-rc4 that fixes a reported
  problem in the binder driver"

* tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: binder: Fix death notifications

Pull char/misc fix from Greg KH:
 "Here is a single commit, to fix a reported problem in the mei driver"

* tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: set client's read_cb to NULL when flow control fails

Add myself as an additional maintainer for the Broadcom mobile
SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>