- 11 Jun, 2014 40 commits
-
-
Amir Vadai authored
This function sets the n'th cpu - local cpu's first. For example: in a 16 cores server with even cpu's local, will get the following values: cpumask_set_cpu_local_first(0, numa, cpumask) => cpu 0 is set cpumask_set_cpu_local_first(1, numa, cpumask) => cpu 2 is set ... cpumask_set_cpu_local_first(7, numa, cpumask) => cpu 14 is set cpumask_set_cpu_local_first(8, numa, cpumask) => cpu 1 is set cpumask_set_cpu_local_first(9, numa, cpumask) => cpu 3 is set ... cpumask_set_cpu_local_first(15, numa, cpumask) => cpu 15 is set Curently this function will be used by multi queue networking devices to calculate the irq affinity mask, such that as many local cpu's as possible will be utilized to handle the mq device irq's. Signed-off-by:
Amir Vadai <amirv@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2014-06-11 This series contains updates to igb, i40e and i40evf. Todd makes a change to igb to un-hide invariant returns by getting rid of the E1000_SUCCESS define and converting those returns to return 0. Jacob separates the hardware logic from the set function, so that we can re-use it during a ptp_reset in igb. This enables the reset to return functionality to the last know timestamp mode, rather than resetting the value. Ashish implements context flags for headwb and headwb_addr so that we do not have to keep them always enabled. Shannon updates the admin queue API for the new firmware, which adds set_pf_content, nvm_config_read/write, replaces set_phy_reset with set_phy_debug and removes nvm_read/write_reg_se. Cleans up the driver to use the stored base_queue value since there is no need to read the PCI register for the PF's base queue on every single transmit queue enable and disable as we already have the value stored from reading the capability features at startup. Anjali changes the notion of source and destination for FD_SB in ethtool to align i40e with other drivers. Adds flow director statistics to the PF stats. Fixes a bug in ethtool for flow director drop packet filter where the drop action comes down as a ring_cookie value, so allow it as a special value that can be used to configure destination control. Mitch fixes the i40evf to keep the driver from going down when it is already in a down state. This prevents a CPU soft lock in napi_disable(). Also change the i40evf to check the admin queue error bits since the firmware can indicate any admin queue error states to the driver via some bits in the length registers. Neerav separates out the DCB capability and enabled flags because currently if the firmware reports DCB capability the driver enables I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver inserts a tag when transmitting a packet from the port even if there are no DCB traffic classes configured at the port. So by adding the additional flag, I40E_FLAG_DCB_CAPABLE, that will be set when the DCB capability is present and the existing enabled flag will only be set if there are more than one traffic classes configured at the port. Greg fixes the i40e driver to not automatically accept tagged packets by default so that the system must request a VLAN tag packet filter to get packets with that tag. Greg also converts i40e to use the in-kernel ether_addr_copy() instead of mempcy(). Jesse removes the FTYPE field from the receive descriptor to match the hardware implementation. ==================== Signed-off-by: -
David S. Miller authored
Daniel Borkmann says: ==================== SCTP update This set contains transport path selection improvements in SCTP. Please see individual patches for details. ==================== Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Daniel Borkmann authored
This fixes the following sparse warning: net/sctp/associola.c:1556:29: warning: incorrect type in initializer (different base types) net/sctp/associola.c:1556:29: expected bool [unsigned] [usertype] preload net/sctp/associola.c:1556:29: got restricted gfp_t Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
In function sctp_select_active_and_retran_path(), we walk the transport list in order to look for the two most recently used ACTIVE transports (trans_pri, trans_sec). In case we didn't find anything ACTIVE, we currently just camp on a possibly PF or INACTIVE transport that is primary path; this behavior actually dates back to linux-history tree of the very early days of lksctp, and can yield a behavior that chooses suboptimal transport paths. Instead, be a bit more clever by reusing and extending the recently introduced sctp_trans_elect_best() handler. In case both transports are evaluated to have the same score resulting from their states, break the tie by looking at: 1) transport patch error count 2) last_time_heard value from each transport. This is analogous to Nishida's Quick Failover draft [1], section 5.1, 3: The sender SHOULD avoid data transmission to PF destinations. When all destinations are in either PF or Inactive state, the sender MAY either move the destination from PF to active state (and transmit data to the active destination) or the sender MAY transmit data to a PF destination. In the former scenario, (i) the sender MUST NOT notify the ULP about the state transition, and (ii) MUST NOT clear the destination's error counter. It is recommended that the sender picks the PF destination with least error count (fewest consecutive timeouts) for data transmission. In case of a tie (multiple PF destinations with same error count), the sender MAY choose the last active destination. Thus for sctp_select_active_and_retran_path(), we keep track of the best, if any, transport that is in PF state and in case no ACTIVE transport has been found (hence trans_{pri,sec} is NULL), we select the best out of the three: current primary_path and retran_path as well as a possible PF transport. The secondary may still camp on the original primary_path as before. The change in sctp_trans_elect_best() with a more fine grained tie selection also improves at the same time path selection for sctp_assoc_update_retran_path() in case of non-ACTIVE states. [1] http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05Signed-off-by: -
Daniel Borkmann authored
Be more precise in transport path selection and use ktime helpers instead of jiffies to compare and pick the better primary and secondary recently used transports. This also avoids any side-effects during a possible roll-over, and could lead to better path decision-making. Signed-off-by:
-
Daniel Borkmann authored
This patch just refactors and moves the code for the active path selection into its own helper function outside of sctp_assoc_control_transport() which is already big enough. No functional changes here. Signed-off-by:
-
Daniel Borkmann authored
Add two minimal helper functions analogous to time_before() and time_after() that will later on both be needed by SCTP code. Signed-off-by:
-
David S. Miller authored
Phoebe Buckheister says: ==================== Recent llsec code introduced a memory leak on decryption failures during rx. This fixes said leak, and optimizes the receive loops for monitor and wpan devices to only deliver skbs to devices that are actually up. Also changes a dev_kfree_skb to kfree_skb when an invalid packet is dropped before being pushed into the stack. ==================== Signed-off-by: -
Phoebe Buckheister authored
Only one WPAN devices can be active at any given time, so only deliver packets to that one interface that is actually up. Multiple monitors may be up at any given time, but we don't have to deliver to monitors that are down either. Signed-off-by:
Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by:
-
Phoebe Buckheister authored
mac802154 RX did not free skbs on decryption failure, assuming that the caller would when the local rx handler returned _DROP. This was false. Signed-off-by:
-
Catherine Sullivan authored
Bump versions. Change-ID: Ic4a84354955061ca18321b1e97c9c30fe1563b5c Signed-off-by:
Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Shannon Nelson authored
No need to read the PCI register for the PF's base queue on every single Tx queue enable and disable as we already have the value stored from reading the capability features at startup. Change-ID: Ic02fb622757742f43cb8269369c3d972d4f66555 Signed-off-by:
Shannon Nelson <shannon.nelson@intel.com> Signed-off-by:
-
Anjali Singhai Jain authored
A drop action comes down as a ring_cookie value, so allow it as a special value that can be used to configure destination control. Also fix the output to filter read command accordingly. Change-ID: I9956723cee42f3194885403317dd21ed4a151144 Signed-off-by:
Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by:
-
Anjali Singhai Jain authored
Add members to stat struct to keep track of Flow director ATR and SideBand filter packet matches. Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c Signed-off-by:
-
Jesse Brandeburg authored
This change drops the FTYPE field from the Rx descriptor, to match the hardware implementation. Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
-
Mitch Williams authored
FW can indicate any admin queue error states to the driver via some bits in the length registers. Each time we process an admin queue message, check these bits and log any errors we find. Since the VF really can't do much, we just print the message and depend on the PF driver to clear things up on our behalf. Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Signed-off-by:
-
Greg Rose authored
Linux gives us a function to copy Ethernet MAC addresses, let's use it. Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd Signed-off-by:
Greg Rose <gregory.v.rose@intel.com> Signed-off-by:
-
Greg Rose authored
Remove the filter created by the firmware with the default MAC address it reads out of the NVM storage and a promiscuous VLAN tag and replace it with a filter that will not accept tagged packets by default. The system must request a VLAN tag packet filter to get packets with that tag. Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a Signed-off-by:
-
Neerav Parikh authored
Currently if the firmware reports DCB capability the driver enables I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver inserts a tag when transmitting a packet from the port even if there are no DCB traffic classes configured at the port. This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set when the DCB capability is present and the existing flag I40E_FLAG_DCB_ENABLED will be set only if there are more than one traffic classes configured at the port. Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5 Signed-off-by:
Neerav Parikh <neerav.parikh@intel.com> Signed-off-by:
-
Mitch Williams authored
If the device is down, there's no place to go but up, so don't try to go down even more. This prevents a CPU soft lock in napi_disable(). Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314 Signed-off-by:
-
Anjali Singhai Jain authored
In XL710 devices we program FD filter's fields from Tx perspective of the flow. However the user interface exposed in ethtool should be compliant with the previous generation of drivers where a filter src and dst field are from the RX perspective. This patch changes the ethtool interface in this regard to match the other drivers. Change-ID: Iec6ccddd87357c4fb53ccf33aa0fae699faf70cf Signed-off-by:
-
Shannon Nelson authored
Add set_pf_context, replace set_phy_reset with set_phy_debug, add nvm_config_read/write, remove nvm_read/write_reg_se and add some PHY types. With these changes we bump the API version to 1.2. Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e Signed-off-by:
-
Ashish Shah authored
Set appropriate fields in Tx queue configuration virtchnl message to pf to enable headwb and setup headwb addr. Then use that info from the VF to set headwb and headwb_addr instead of always enabling them. Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622 Signed-off-by:
Ashish Shah <ashish.n.shah@intel.com> Signed-off-by:
-
Jacob Keller authored
This patch separates the hardware logic from the set function, so that we can re-use it during a ptp_reset. This enables the reset to return functionality to the last known timestamp mode, rather than resetting the value. We initialize the mode to off during the ptp_init cycle. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Todd Fujinaka authored
Return a 0 directly rather than a constant. Reported-by:
Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by:
Todd Fujinaka <todd.fujinaka@intel.com> Tested-by:
-
Lendacky, Thomas authored
MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc architecture. Rename this #define in xgbe.h to avoid the redefined warning issued during compilation. Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Ben Hutchings authored
Use dma_addr_t for DMA address parameters and u32 for shared memory offset parameters. Do not assume that dma_addr_t is the same as unsigned long; it will not be in PAE configurations. Truncate DMA addresses to 32 bits when printing them. This is OK because the DMA mask for this device is 32-bit (per default). Also rename the DMA address parameters from 'skb' to 'dma'. Compile-tested only. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
David S. Miller authored
Or Gerlitz says: ==================== mlx4 SRIOV fixes The patch from Wei Yang is a designed fix to a regression introduced by earlier commit of him. Jack added a fix to the resource management which we got from IBM. Let's get that into 3.16-rc1 1st and later see to what stable version/s this should go. ==================== Signed-off-by: -
Wei Yang authored
Following commit befdf897 "net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()", there are two mlx4 pci callbacks which will attempt to release the mlx4_priv object -- .shutdown and .remove. This leads to a use-after-free access to the already freed mlx4_priv instance and trigger a "Kernel access of bad area" crash when both .shutdown and .remove are called. During reboot or kexec, .shutdown is called, with the VFs probed to the host going through shutdown first and then the PF. Later, the PF will trigger VFs' .remove since VFs still have driver attached. Fix that by keeping only one driver entry which releases mlx4_priv. Fixes: befdf897 ('net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()') CC: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by:
-
Jack Morgenstein authored
The Hypervisor driver tracks free slots and reserved slots at the global level and tracks allocated slots and guaranteed slots per VF. Guaranteed slots are treated as reserved by the driver, so the total reserved slots is the sum of all guaranteed slots over all the VFs. As VFs allocate resources, free (global) is decremented and allocated (per VF) is incremented for those resources. However, reserved (global) is never changed. This means that effectively, when a VF allocates a resource from its guaranteed pool, it is actually reducing that resource's free pool (since the global reserved count was not also reduced). The fix for this problem is the following: For each resource, as long as a VF's allocated count is <= its guaranteed number, when allocating for that VF, the reserved count (global) should be reduced by the allocation as well. When the global reserved count reaches zero, the remaining global free count is still accessible as the free pool for that resource. When the VF frees resources, the reverse happens: the global reserved count for a resource is incremented only once the VFs allocated number falls below its guaranteed number. This fix was developed by Rick Kready <kready@us.ibm.com> Reported-by:
Rick Kready <kready@us.ibm.com> Signed-off-by:
-
Rickard Strandqvist authored
Logical conjunction always evaluates to false: minor < 2 && minor > 1 I guess what you wanted is rather: minor > 2 || minor < 1 This was partly found using a static code analysis program called cppcheck. Signed-off-by:
Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by:
-
Rickard Strandqvist authored
A check on a memory allocation is checked incorrectly. This was partly found using a static code analysis program called cppcheck. Signed-off-by:
Geoff Levand <geoff@infradead.org> Signed-off-by:
-
françois romieu authored
Fix following compilation warning: [...] CC drivers/net/phy/amd-xgbe-phy.o drivers/net/phy/amd-xgbe-phy.c:1353:30: warning: ‘amd_xgbe_phy_ids’ defined but not used [-Wunused-variable] static struct mdio_device_id amd_xgbe_phy_ids[] = { ^ Signed-off-by:Francois Romieu <romieu@fr.zoreil.com> Acked-by:
-
Alexei Starovoitov authored
- 'struct nlattr' must be 2 byte aligned - provide big-endian input data for nlattr/nlattr_nest tests Signed-off-by:
Alexei Starovoitov <ast@plumgrid.com> Acked-by:
-
Alexei Starovoitov authored
The macro 'A' used in internal BPF interpreter: #define A regs[insn->a_reg] was easily confused with the name of classic BPF register 'A', since 'A' would mean two different things depending on context. This patch is trying to clean up the naming and clarify its usage in the following way: - A and X are names of two classic BPF registers - BPF_REG_A denotes internal BPF register R0 used to map classic register A in internal BPF programs generated from classic - BPF_REG_X denotes internal BPF register R7 used to map classic register X in internal BPF programs generated from classic - internal BPF instruction format: struct sock_filter_int { __u8 code; /* opcode */ __u8 dst_reg:4; /* dest register */ __u8 src_reg:4; /* source register */ __s16 off; /* signed offset */ __s32 imm; /* signed immediate constant */ }; - BPF_X/BPF_K is 1 bit used to encode source operand of instruction In classic: BPF_X - means use register X as source operand BPF_K - means use 32-bit immediate as source operand In internal: BPF_X - means use 'src_reg' register as source operand BPF_K - means use 32-bit immediate as source operand Suggested-by:Chema Gonzalez <chema@google.com> Signed-off-by:
-
David S. Miller authored
Linus Lüssing says: ==================== bridge: multicast snooping patches / exports The first patch is simply a cosmetic patch. So far I (and maybe others too?) have been regularly confusing these two structs, therefore I'd suggest renaming them and therefore making the follow-up patches easier to understand and nicer to fit in. The second patch fixes a minor issue, but probably not worth for stable. On the other hand the first two patches are also preparations for the third and fourth patch: These two patches are exporting functionality needed to marry the bridge multicast snooping with the batman-adv multicast optimizations recently added for the 3.15 kernel, allowing to use these optimzations in common setups having a bridge on top of e.g. bat0, too. So far these bridged setups would fall back to simple flooding through the batman-adv mesh network for any multicast packet entering bat0. More information about the batman-adv multicast optimizations currently implemented can be found here: http://www.open-mesh.org/projects/batman-adv/wiki/Basic-multicast-optimizations The integration on the batman-adv side could afterwards look like this, for instance: http://git.open-mesh.org/batman-adv.git/commitdiff/576b59dd3e34737c702e548b21fa72059262f796?hp=f95ce7131746c65fbcdffcf2089cab59e2c2f7ac ==================== Signed-off-by:
-
Linus Lüssing authored
Adding bridge support to the batman-adv multicast optimization requires batman-adv knowing about the existence of bridged-in IGMP/MLD queriers to be able to reliably serve any multicast listener behind this same bridge. Signed-off-by:
Linus Lüssing <linus.luessing@web.de> Signed-off-by:
-
Linus Lüssing authored
With this new, exported function br_multicast_list_adjacent(net_dev) a list of IPv4/6 addresses is returned. This list contains all multicast addresses sensed by the bridge multicast snooping feature on all bridge ports of the bridge interface of net_dev, excluding addresses from the specified net_device itself. Adding bridge support to the batman-adv multicast optimization requires batman-adv knowing about the existence of bridged-in multicast listeners to be able to reliably serve them with multicast packets. Signed-off-by:
-
Linus Lüssing authored
MLDv1 (RFC2710 section 6), MLDv2 (RFC3810 section 7.6.2), IGMPv2 (RFC2236 section 3) and IGMPv3 (RFC3376 section 6.6.2) specify that the querier with lowest source address shall become the selected querier. So far the bridge stopped its querier as soon as it heard another querier regardless of its source address. This results in the "wrong" querier potentially becoming the active querier or a potential, unnecessary querying delay. With this patch the bridge memorizes the source address of the currently selected querier and ignores queries from queriers with a higher source address than the currently selected one. This slight optimization is supposed to make it more RFC compliant (but is rather uncritical and therefore probably not necessary to be queued for stable kernels). Signed-off-by:
-
