- 12 Feb, 2024 5 commits
-
-
Marc Kleine-Budde authored
Stefan Mätje <stefan.maetje@esd.eu> says: The purpose of this patch is to introduce a new CAN driver to support the esd GmbH 402 family of CAN interface boards. The hardware design is based on a CAN controller implemented in a FPGA attached to a PCIe link. More information on these boards can be found following the links included in the commit message. This patch supports all boards but will operate the CAN-FD capable boards only in Classic-CAN mode. The CAN-FD support will be added when the initial patch has stabilized. The patch is reuses the previous work of my former colleague: Link: https://lore.kernel.org/linux-can/1426592308-23817-1-git-send-email-thomas.koerper@esd.eu The patch is based on the linux-can-next main branch. Changed in v11: No functional, only editorial changes due to feedback on v10. - Make lifetime of macros used for hardware timestamp calculation very short by #undef-ing them after use. - Fixed insertion order of new entry in MAINTAINERS file. Changed in v10: Most changes due to feedback by Vincent Mailhol https://lore.kernel.org/linux-can/CAMZ6RqLOAC930GNOU+pWuoi6FgYwFOuFrSyAzVjvE2fuVgy8oA@mail.gmail.com - Add support for ethtool operations by using default operations provided by the can_dev module for drivers with hardware time stamp support. - Factor out core unregistration into pci402_unregister_core(). - Factor out getting next TX fifo index into acc_tx_fifo_next(). - Stop counting alloc_can_err_skb() failures in rx_dropped statistic. - Add CAN_ERR_CNT flag in CAN error frames as needed. - Rework function acc_reset_fpga(). To clear I^2C bus enable bit is not necessary after FPGA reset. - Simplify struct acc_bmmsg_rxtxdone layout. - Additional non functional changes due to feedback by Vincent - Some spelling corrections: ESDACC -> esdACC Changes in v9: - Fix returning success error code in case of allocation failure in pci402_probe(). Changes in v8: - Rebased to 6.6-rc2 on linux-can-next branch main Changes in v7: - Numerous changes. Find the quoted with inline comments about changes below after the changes list. Stuff that I don't understand and where I have questions is marked with ????. Unfortunately I will be AFK till 28th of November. Changes in v6: - Fixed the statistic handling of RX overrun errors and increase net_device_stats::rx_errors instead of net_device_stats::rx_dropped. - Added a patch to not increase rx statistics when generating a CAN rx error message frame as suggested on the linux-can list. - Added a patch to not not increase rx_bytes statistics for RTR frames as suggested on the linux-can list. The last two patches change the statistics handling from the previous style used in other drivers to the newly suggested one. Changes in v5: - Added the initialization for netdev::dev_port as it is implemented for another CAN driver. See https://lore.kernel.org/linux-can/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr Changes in v4: - Fixed the build failure on ARCH=arm64 that was found by the Intel kernel test robot. See https://lore.kernel.org/linux-can/202109120608.7ZbQXkRh-lkp@intel.com Removed error monitoring code that used GCC's built-in compiler functions for atomic access (__sync_* functions). GCC versions after 9 (tested with "gcc-10 (Ubuntu 10.3.0-1ubuntu1~20.04)") don't implement the intrinsic atomic as in-line code but call "__aarch64_ldadd4_acq_rel" on arm64. This GCC support function is not exported by the kernel and therefore the module build post-processing fails. Removed that code because the error monitoring never showed a problem during the development this year. Changes in v3: - Rework the bus-off restart logic in acc_set_mode() and handle_core_msg_errstatechange() to call netif_wake_queue() from the error active event. - Changed pci402_init_card() to allocate a variable sized array of struct acc_core using devm_kcalloc() instead of using a fixed size array in struct pci402_card. - Changed handle_core_msg_txabort() to release aborted TX frames in TX FIFO order. - Fixed the acc_close() function to abort all pending TX request in esdACC controller. - Fixed counting of transmit aborts in handle_core_msg_txabort(). It is now done like in can_flush_echo_skb(). - Fixed handle_core_msg_buserr() to create error frames including the CAN RX and TX error counters that were missing. - Fixed acc_set_bittiming() neither to touch LOM mode setting of esdACC controller nor to enter or leave RESET mode. The esdACC controller is going active on the CAN bus in acc_open() and is going inactive (RESET mode) again in acc_close(). - Rely on the automatic release of memory fetched by devm_kzalloc(). But still use devm_irq_free() explicitely to make sure that the interrupt handler is disconnected at that point. This avoids a possible crash in non-MSI mode due to the IRQ triggered by another device on the same PCI IRQ line. - Changed to use DMA map API instead of pci_*_consistent compatibility wrappers. - Fixed stale email references and updated copyright information. - Removed any traces of future CAN-FD support. Changes in v2: - Avoid warning triggered by -Wshift-count-overflow on architectures with 32-bit dma_addr_t. - Fixed Makefile not to build the kernel module always. Doing this renamed esd402_pci.c to esd_402_pci-core.c as recommended by Marc. previous versions: v1 - https://lore.kernel.org/linux-can/20210728203647.15240-1-Stefan.Maetje@esd.eu v2 - https://lore.kernel.org/linux-can/20210730173805.3926-1-Stefan.Maetje@esd.eu v3 - https://lore.kernel.org/linux-can/20210908164640.23243-1-stefan.maetje@esd.eu v4 - https://lore.kernel.org/linux-can/20210916172152.5127-1-stefan.maetje@esd.eu v5 - https://lore.kernel.org/linux-can/20211109155326.2608822-1-stefan.maetje@esd.eu v6 - https://lore.kernel.org/linux-can/20211201220328.3079270-1-stefan.maetje@esd.eu v7 - https://lore.kernel.org/linux-can/20221106224156.3619334-1-stefan.maetje@esd.eu v8 - https://lore.kernel.org/linux-can/20231025141635.1459606-1-stefan.maetje@esd.eu v9 - https://lore.kernel.org/linux-can/20231107184103.2802678-1-stefan.maetje@esd.eu v10 - https://lore.kernel.org/linux-can/20231120175657.4070921-1-stefan.maetje@esd.eu Link: https://lore.kernel.org/all/20231122160211.2110448-1-stefan.maetje@esd.euSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Stefan Mätje authored
This patch adds support for the PCI based PCIe/402 CAN interface family from esd GmbH that is available with various form factors (https://esd.eu/en/products/402-series-can-interfaces). All boards utilize a FPGA based CAN controller solution developed by esd (esdACC). For more information on the esdACC see https://esd.eu/en/products/esdacc. This driver detects all available CAN interface board variants of the family but atm. operates the CAN-FD capable devices in Classic-CAN mode only! A later patch will introduce the CAN-FD functionality in this driver. Co-developed-by: Thomas Körper <thomas.koerper@esd.eu> Signed-off-by: Thomas Körper <thomas.koerper@esd.eu> Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Link: https://lore.kernel.org/all/20231122160211.2110448-3-stefan.maetje@esd.euSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Stefan Mätje authored
Adding myself (Stefan Mätje) as a maintainer for the upcoming driver of the PCIe/402 interface card family. Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Link: https://lore.kernel.org/all/20231122160211.2110448-2-stefan.maetje@esd.euSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Oliver Hartkopp authored
The ISO15765-2 standard supports to take the PDUs communication parameters blocksize (BS) and Separation Time minimum (STmin) either from the first received flow control (FC) "static" or from every received FC "dynamic". Add a new CAN_ISOTP_DYN_FC_PARMS flag to support dynamic FC parameters. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20231208165729.3011-1-socketcan@hartkopp.netSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Nicolas Maier authored
CAN RAW sockets allow userspace to tell if a received CAN frame comes from the same socket, another socket on the same host, or another host. See commit 1e55659c ("can-raw: add msg_flags to distinguish local traffic"). However, this feature is missing in CAN BCM sockets. Add the same feature to CAN BCM sockets. When reading a received frame (opcode RX_CHANGED) using recvmsg, two flags in msg->msg_flags may be set following the previous convention (from CAN RAW), to distinguish between 'own', 'local' and 'remote' CAN traffic. Update the documentation to reflect this change. Signed-off-by: Nicolas Maier <nicolas.maier.dev@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20240120081018.2319-1-socketcan@hartkopp.netSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
- 10 Feb, 2024 11 commits
-
-
David S. Miller authored
Christian Marangi says: ==================== net: phy: Introduce PHY Package concept Idea of this big series is to introduce the concept of PHY package in DT and give PHY drivers a way to derive the base address from DT. The concept of PHY package is nothing new and is already a thing in the kernel with the API phy_package_join/leave/read/write. What is currently lacking is describing this in DT and better reference a base address to calculate offset from. In the scenario of a PHY package where multiple address are used and there isn't a way to get the base address of the PHY package from some regs, getting the information from DT is the only way. A possible example to this problem is this: ethernet-phy-package@0 { compatible = "qcom,qca8075-package"; #address-cells = <1>; #size-cells = <0>; reg = <0>; qcom,package-mode = "qsgmii"; ethernet-phy@1 { reg = <1>; }; phy4: ethernet-phy@4 { reg = <4>; }; }; The mdio parse functions are changed to address for this additional special node, the function is changed to simply detect this node and search also in this. (we match the node name to be "ethernet-phy-package") PHY driver can then use introduced helper of_phy_package_join to join the PHY to the PHY package and derive the base address from DT. Changes v7: - Rebase on top of net-next - Add Reviewed-by tag for DT patch - Change tx-driver-strength to tx-drive-strength - Drop driver reference in DT Changes v6: - Back to absolute PHY implementation - Correctly drop refcount for node on error condition and on PHY leave - Drop DT include patch in favor for 3 boolean vendor property - Fix Documentation problem for compatible and missing type and description - Drop redundand gpio-controller dependency and description - Skip scanphy with invalid PHY Package node and make reg mandatory - Rework fiber read status to use more generic function - Split qca808x LED generalization patch to permit easier review - Correctly return -EINVAL with wrong data passed to vendor property - Drop removing LED ops for qca807x PHY driver with gpio-controller Changes v5: - Rebase on top of net-next - Change implementation to base addr + offset in subnode - Adapt to all the changes and cleanup done to at803x Changes v4: - Rework DT implementation - Drop of autojoin support and rework to simple helper - Rework PHY driver to the new implementation - Add compatible for qca807x package - Further cleanup patches Changes v3: - Add back compatible implementation - Detach patch that can be handled separately (phy_package_mmd, phy_package extended) - Rework code to new simplified implementation with base addr + offset - Improve documentation with additional info and description Changes v2: - Drop compatible "ethernet-phy-package", use node name prefix matching instead - Improve DT example - Add reg for ethernet-phy-package - Drop phy-mode for ethernet-phy-package - Drop patch for generalization of phy-mode - Drop global-phy property (handle internally to the PHY driver) - Rework OF phy package code and PHY driver to handle base address - Fix missing of_node_put - Add some missing docs for added variables in struct - Move some define from dt-bindings include to PHY driver - Handle qsgmii validation in PHY driver - Fix wrong include for gpiolib - Drop reduntant version.h include ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
QCA8072/5 have up to 2 LEDs attached for PHY. LEDs can be configured to be ON/hw blink or be set to HW control. Hw blink mode is set to blink at 4Hz or 250ms. PHY can support both copper (TP) or fiber (FIBRE) kind and supports different HW control modes based on the port type. HW control modes supported for netdev trigger for copper ports are: - LINK_10 - LINK_100 - LINK_1000 - TX - RX - FULL_DUPLEX - HALF_DUPLEX HW control modes supported for netdev trigger for fiber ports are: - LINK_100 - LINK_1000 - TX - RX - FULL_DUPLEX - HALF_DUPLEX LED support conflicts with GPIO controller feature and must be disabled if gpio-controller is used for the PHY. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Generalize some qca808x LED functions in preparation for qca807x LED support. The LED implementation of qca808x and qca807x is the same but qca807x supports also Fiber port and have different hw control bits for Fiber port. To limit code duplication introduce micro functions that takes reg instead of LED index to tweak all the supported LED modes. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
The LED implementation of qca808x and qca807x is the same but qca807x supports also Fiber port and have different hw control bits for Fiber port. In preparation for qca807x introduction, move all the common define to shared header. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Robert Marko authored
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s. They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC, while second one is SGMII for connection to MAC or fiber. Both models have a combo port that supports 1000BASE-X and 100BASE-FX fiber. PHY package can be configured in 3 mode following this table: First Serdes mode Second Serdes mode Option 1 PSGMII for copper Disabled ports 0-4 Option 2 PSGMII for copper 1000BASE-X / 100BASE-FX ports 0-4 Option 3 QSGMII for copper SGMII for ports 0-3 copper port 4 Each PHY inside of QCA807x series has 4 digitally controlled output only pins that natively drive LED-s. But some vendors used these to driver generic LED-s controlled by userspace, so lets enable registering each PHY as GPIO controller and add driver for it. These are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x boards. Co-developed-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Some PHY driver might require additional regs call after genphy_c37_read_status() is called. Expand genphy_c37_read_status to provide a bool wheather the link has changed or not to permit PHY driver to skip additional regs call if nothing has changed. Every user of genphy_c37_read_status() is updated with the new additional bool. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Document Qcom QCA807x PHY package. Qualcomm QCA807X Ethernet PHY is PHY package of 2 or 5 IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. Document the required property to make the PHY package correctly configure and work. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Move more function to shared library in preparation for introduction of new PHY Family qca807x that will make use of both functions from at803x and qca808x as it's a transition PHY with some implementation of at803x and some from the new qca808x. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Add devm/of_phy_package_join helper to join PHYs in a PHY package. These are variant of the manual phy_package_join with the difference that these will use DT nodes to derive the base_addr instead of manually passing an hardcoded value. An additional value is added in phy_package_shared, "np" to reference the PHY package node pointer in specific PHY driver probe_once and config_init_once functions to make use of additional specific properties defined in the PHY package node in DT. The np value is filled only with of_phy_package_join if a valid PHY package node is found. A valid PHY package node must have the node name set to "ethernet-phy-package". Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Add support for scanning PHY in PHY package nodes. PHY packages nodes are just container for actual PHY on the MDIO bus. Their PHY address defined in the PHY package node are absolute and reflect the address on the MDIO bus. mdio_bus.c and of_mdio.c is updated to now support and parse also PHY package subnode by checking if the node name match "ethernet-phy-package". As PHY package reg is mandatory and each PHY in the PHY package must have a reg, every invalid PHY Package node is ignored and will be skipped by the autoscan fallback. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Document ethernet PHY package nodes used to describe PHY shipped in bundle of 2-5 PHY. The special node describe a container of PHY that share common properties. This is a generic schema and PHY package should create specialized version with the required additional shared properties. Example are PHY packages that have some regs only in one PHY of the package and will affect every other PHY in the package, for example related to PHY interface mode calibration or global PHY mode selection. The PHY package node MUST declare the base address used by the PHY driver for global configuration by calculating the offsets of the global PHY based on the base address of the PHY package. Each reg of the PHYs defined in the PHY package node is absolute and describe the real address of the Ethernet PHY on the bus. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 09 Feb, 2024 24 commits
-
-
Heiner Kallweit authored
Use generic MDIO helpers to simplify the code. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/422ae70f-7305-45fd-ab3e-0dd604b9fd6c@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== igc: ethtool: Flex filter cleanup Kurt Kanzenbach says: This series contains some cosmetics for the flex filter code. The fixes have been merged separately via -net already. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: igc: Unify filtering rule fields igc: Use netdev printing functions for flex filters igc: Use reverse xmas tree ==================== Link: https://lore.kernel.org/r/20240207191656.1250777-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Sitnicki authored
udpgso regression test configures routing and device MTU directly through uAPI (Netlink, ioctl) to do its job. While there is nothing wrong with it, it takes more effort than doing it from shell. Looking forward, we would like to extend the udpgso regression tests to cover the EIO corner case [1], once it gets addressed. That will require a dummy device and device feature manipulation to set it up. Which means more Netlink code. So, in preparation, pull out network configuration into the shell script part of the test, so it is easily extendable in the future. Also, because it now easy to setup routing, add a second local IPv6 address. Because the second address is not managed by the kernel, we can "replace" the corresponding local route with a reduced-MTU one. This unblocks the disabled "ipv6 connected" test case. Add a similar setup for IPv4 for symmetry. [1] https://lore.kernel.org/netdev/87jzqsld6q.fsf@cloudflare.com/Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/r/20240207-jakub-krn-635-v3-1-3dfa3da8a7d3@cloudflare.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Heiner Kallweit authored
Convert EEE handling to use linkmode bitmaps. This prepares for removing the legacy bitmaps from struct ethtool_keee. No functional change intended. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/c5a61d57-d2b0-427f-93b3-fcf7721165f3@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Heiner Kallweit authored
Convert EEE handling to use linkmode bitmaps. This prepares for removing the legacy bitmaps from struct ethtool_keee. No functional change intended. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/948562fb-c5d8-4912-8b88-bec56238732a@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Heiner Kallweit authored
After 3a2746320403 ("leds: trigger: netdev: Display only supported link speed attribute") the check for valid link modes can be simplified. In addition factor it out, so that it can be re-used by the upcoming LED support for RTL8125. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/8876a9f4-7a2d-48c3-8eae-0d834f5c27c5@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Paolo Abeni authored
The altnames test uses the forwarding/lib.sh and that dependency currently causes failures when running the test after install: make -C tools/testing/selftests/ TARGETS=net install ./tools/testing/selftests/kselftest_install/run_kselftest.sh \ -t net:altnames.sh # ... # ./altnames.sh: line 8: ./forwarding/lib.sh: No such file or directory # RTNETLINK answers: Operation not permitted # ./altnames.sh: line 73: tests_run: command not found # ./altnames.sh: line 65: pre_cleanup: command not found Address the issue leveraging the TEST_INCLUDES infrastructure provided by commit 2a0683be ("selftests: Introduce Makefile variable to list shared bash scripts") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/f7b1e9d468224cbc136d304362315499fe39848f.1707298927.git.pabeni@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Michael Chan says: ==================== bnxt_en: Ntuple and RSS updates This patch series adds more ntuple and RSS features following recent patches to add support for user configured ntuple filters. Additional features include L2 ether filters, partial tuple masks, IP filters besides TCP/UDP, drop action, saving and re-applying user filters after driver reset, user configured RSS key, and RSS for IPSEC. ==================== Link: https://lore.kernel.org/r/20240205223202.25341-1-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Ajit Khaparde authored
IPSec uses two distinct protocols, Authentication Header (AH) and Encapsulating Security Payload (ESP). Add support to configure RSS based on AH and ESP headers. This functionality will be enabled based on the capabilities indicated by the firmware in HWRM_VNIC_QCAPS. Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-14-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Pavan Chebbi authored
The cached user filters slated to be reapplied need to be cleared if configured MAC changes, RSS key changes, number of rings changes, or ntuple is disabled. Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-13-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Pavan Chebbi authored
Store the user configured or generated Toeplitz key in bp->rss_hash_key. The key stays constant across ifdown/ifup unless updated by the user. Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-12-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Pavan Chebbi authored
Walk the usr_fltr_list and call firmware to add these filters when we open the NIC. This will restore all user created filters after reset. Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-11-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Pavan Chebbi authored
Driver should not free user created filters from its memory when closing since we are going to reconfigure them when we open again. If the "all" parameter is false, do not free user configured filters in bnxt_free_ntp_fltrs() and bnxt_free_l2_filters(). Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-10-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Pavan Chebbi authored
Driver needs to maintain a lookup list of all the user configured filters. This is required in order to reconfigure these filters upon interface toggle. We can look up this list to follow the order with which they should be re-applied. Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-9-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Pavan Chebbi authored
Since we are going to do filter deletion at multiple places in the upcoming patches, add a function that does the deletion. Future patches add more code into this function. Since we are passing the address of the filter base to free the entire filter structure, add a comment to make sure that the base is always at the beginning of the structure. Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-8-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Vikas Gupta authored
Add drop action for protocols TCP/UDP/ICMP 1) Drop action for TCP/UDP is supported via flow type tcp4/udp4/tcp6/udp6. 2) Drop action for ICMPV4/ICMPV6/wildcard is supported via flow type ipv4/ipv6. Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-7-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Vikas Gupta authored
Enable flow type ipv4/ipv6 1) for protocols ICMPV4 and ICMPV6. 2) for wildcard match. Wildcard matches to TCP/UDP/ICMP. Note that, IPPROTO_RAW(255) i.e. a reserved protocol considered for a wildcard. Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-6-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Edwin Peer authored
Support subfield masking for IP addresses and ports. Previously, only entire fields could be included or excluded in NTUPLE filters. Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://lore.kernel.org/r/20240205223202.25341-5-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Michael Chan authored
Implement ETHTOOL_GRXCLSRULE for the user defined ether filters. Use the common functions to walk the L2 filter hash table. Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://lore.kernel.org/r/20240205223202.25341-4-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Michael Chan authored
Add ETHTOOL_SRXCLSRLINS and ETHTOOL_SRXCLSRLDEL support for inserting and deleting L2 ether filter rules. Destination MAC address and optional VLAN are supported for each filter entry. This is currently only supported on older BCM573XX and BCM574XX chips only. Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240205223202.25341-3-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Michael Chan authored
While individual filter structures are allocated as needed, there is an array to keep track of the software filter IDs that we allocate ahead of time. Rather than relying on a fixed maximum filter count to allocate this array, get the maximum from the firmware when available. Move these filter related maximum counts queried from the firmware to the bnxt_hw_resc struct. If the firmware is not providing these maximum counts, fall back to the hard-coded constant. Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://lore.kernel.org/r/20240205223202.25341-2-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Victor Nogueira authored
Add 8 new mirred tdc tests that target mirred to block: - Add mirred mirror to egress block action - Add mirred mirror to ingress block action - Add mirred redirect to egress block action - Add mirred redirect to ingress block action - Try to add mirred action with both dev and block - Try to add mirred action without specifying neither dev nor block - Replace mirred redirect to dev action with redirect to block - Replace mirred redirect to block action with mirror to dev Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20240202020726.529170-1-victor@mojatatu.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Markus Elfring authored
A wrapper function is available since the commit 890cc39a ("drivers: provide devm_platform_get_and_ioremap_resource()"). Thus reuse existing functionality instead of keeping duplicate source code. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Link: https://lore.kernel.org/r/f87065d0-e398-4ffa-bfa4-9ff99d73f206@web.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Markus Elfring authored
A wrapper function is available since the commit 890cc39a ("drivers: provide devm_platform_get_and_ioremap_resource()"). Thus reuse existing functionality instead of keeping duplicate source code. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Link: https://lore.kernel.org/r/46f64db3-3f8f-4c6c-8d70-38daeefccac1@web.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-