- 04 Aug, 2015 40 commits
-
-
Tomas Winkler authored
commit 9098f84c upstream. Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler, let's add it. Fixes: add710ea ("mmc: boot partition ro lock support") Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Joe Thornber authored
commit 1c751879 upstream. Allocate memory using GFP_NOIO when deleting a btree. dm_btree_del() can be called via an ioctl and we don't want to recurse into the FS or block layer. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Dennis Yang authored
commit 4c7e3093 upstream. redistribute3() shares entries out across 3 nodes. Some entries were being moved the wrong way, breaking the ordering. This manifested as a BUG() in dm-btree-remove.c:shift() when entries were removed from the btree. For additional context see: https://www.redhat.com/archives/dm-devel/2015-May/msg00113.htmlSigned-off-by:
Dennis Yang <shinrairis@gmail.com> Signed-off-by:
-
Joe Thornber authored
commit 6096d91a upstream. The metadata space map has a simplified 'bootstrap' mode that is operational when extending the space maps. Whilst in this mode it's possible for some refcount decrement operations to become queued (eg, as a result of shadowing one of the bitmap indexes). These decrements were not being applied when switching out of bootstrap mode. The effect of this bug was the leaking of a 4k metadata block. This is detected by the latest version of thin_check as a non fatal error. Signed-off-by:
-
Mikulas Patocka authored
commit dd4c1b7d upstream. If the number_of_areas argument was zero the kernel would crash on div-by-zero. Add better input validation. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
AMAN DEEP authored
commit 34968106 upstream. virt_dev->num_cached_rings counts on freed ring and is not updated correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring is added into cache and then num_rings_cache is incremented as below: virt_dev->ring_cache[rings_cached] = virt_dev->eps[ep_index].ring; virt_dev->num_rings_cached++; here, free ring pointer is added to a current index and then index is incremented. So current index always points to empty location in the ring cache. For getting available free ring, current index should be decremented first and then corresponding ring buffer value should be taken from ring cache. But In function xhci_endpoint_init(), the num_rings_cached index is accessed before decrement. virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; virt_dev->num_rings_cached--; This is bug in manipulating the index of ring cache. And it should be as below: virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; Signed-off-by:
Aman Deep <aman.deep@samsung.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Johannes Thumshirn authored
commit d23f47d4 upstream. Destroy serial_minors IDR on module exit, reclaiming the allocated memory. This was detected by the following semantic patch (written by Luis Rodriguez <mcgrof@suse.com>) <SmPL> @ defines_module_init @ declarer name module_init, module_exit; declarer name DEFINE_IDR; identifier init; @@ module_init(init); @ defines_module_exit @ identifier exit; @@ module_exit(exit); @ declares_idr depends on defines_module_init && defines_module_exit @ identifier idr; @@ DEFINE_IDR(idr); @ on_exit_calls_destroy depends on declares_idr && defines_module_exit @ identifier declares_idr.idr, defines_module_exit.exit; @@ exit(void) { ... idr_destroy(&idr); ... } @ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @ identifier declares_idr.idr, defines_module_exit.exit; @@ exit(void) { ... +idr_destroy(&idr); } </SmPL> Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Claudio Cappelli authored
commit f6d7fb37 upstream. Add device Olivetti Olicard 300 (Network Connect: MT6225) - IDs 2020:4000. T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=4000 Rev=03.00 S: Manufacturer=Network Connect S: Product=MT6225 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Signed-off-by:
Claudio Cappelli <claudio.cappelli.linux@gmail.com> Suggested-by:
Lars Melin <larsm17@gmail.com> [johan: amend commit message with devices info ] Signed-off-by:
-
Peter Sanford authored
commit f98a7aa8 upstream. Add the USB serial console device ID for Aruba Networks 7xxx series controllers which have a USB port for their serial console. Signed-off-by:
Peter Sanford <peter@sanford.io> Signed-off-by:
-
Felipe Balbi authored
commit be9d3988 upstream. Currently, we're calling musb_start() twice for DRD ports in some situations. This has been observed to cause enumeration issues after suspend/resume cycles with AM335x. In order to fix the problem, we just have to fix the check on musb_has_gadget() so that it only returns true if current mode is Host and ignore the fact that we have or not a gadget driver loaded. Fixes: ae44df2e (usb: musb: call musb_start() only once in OTG mode) Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Dan Carpenter authored
commit 83ed07c5 upstream. Static checkers complain that the current condition is never true. It seems pretty likely that it's a typo and "URB" was intended instead of "USB". Fixes: 3d97ff63 ('usbdevfs: Use scatter-gather lists for large bulk transfers') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
John Youn authored
commit aebda618 upstream. This fixes an issue introduced in commit b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by:
Huang Rui <ray.huang@amd.com> Tested-by:
Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
Subbaraya Sundeep Bhatta authored
commit 76e838c9 upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by:
Subbaraya Sundeep Bhatta <sbhatta@xilinx.com> Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by:
-
Subbaraya Sundeep Bhatta authored
commit 891b1dc0 upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by:
-
Mikulas Patocka authored
commit d531be2c upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Aleksei Mamlin authored
commit 08c85d2a upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Zidan Wang authored
commit a077e81e upstream. the enum of "DAC Polarity" should be wm8960_enum[1]. Signed-off-by:
Zidan Wang <zidan.wang@freescale.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Axel Lin authored
commit ebb6ad73 upstream. VMID Control 0 BIT[2:1] is VMID Divider Enable and Select 00 = VMID disabled (for OFF mode) 01 = 2 x 50kΩ divider (for normal operation) 10 = 2 x 250kΩ divider (for low power standby) 11 = 2 x 5kΩ divider (for fast start-up) So WM8903_VMID_RES_250K should be 2 << 1, which is 4. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Axel Lin authored
commit 12c35005 upstream. WM8955_K_8_0_MASK bits is controlled by WM8955_PLL_CONTROL_3 rather than WM8955_PLL_CONTROL_2. Signed-off-by:
-
Axel Lin authored
commit 14ba3ec1 upstream. According to the datasheet: R10 (0Ah) VMID Impedance Control BIT 3:2 VMIDSEL DEFAULT 00 DESCRIPTION: VMID impedance selection control 00: 75kΩ output 01: 300kΩ output 10: 2.5kΩ output WM8737_VMIDSEL_MASK is 0xC (VMIDSEL - [3:2]), so it needs to left shift WM8737_VMIDSEL_SHIFT bits for setting these bits. Signed-off-by:
-
Dan Carpenter authored
commit 474ff0ae upstream. My static checker complains that: sound/soc/fsl/imx-wm8962.c:196 imx_wm8962_probe() warn: we tested 'ret' before and it was 'false' The intent was that we use "ret" to check imx_audmux_v2_configure_port(). Fixes: 8de2ae2a ('ASoC: fsl: add imx-wm8962 machine driver') Signed-off-by:
-
Richard Fitzgerald authored
commit 15575ed5 upstream. The Arizona codec drivers had an incorrect dB scaling for the noise generator gain that started at 0dB and went upwards. Actually the highest setting is 0dB. Signed-off-by:
Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 1fa2337a upstream. The maximum size for a DiSEqC command is 6, according to the userspace API. However, the code allows to write up much more values: drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23 Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 12f4543f upstream. The maximum size for a DiSEqC command is 6, according to the userspace API. However, the code allows to write up to 7 values: drivers/media/dvb-frontends/s5h1420.c:193 s5h1420_send_master_cmd() error: buffer overflow 'cmd->msg' 6 <= 7 Signed-off-by:
-
Mauro Carvalho Chehab authored
commit d7b76c91 upstream. If userspace sends an invalid bandwidth, it should either return EINVAL or switch to auto mode. This driver will go past an array and program the hardware on a wrong way if this happens. Signed-off-by:
-
Jan Leupold authored
commit 2ab5f39b upstream. The DT-Property "atmel,adc-startup-time" is stored in an u8 for a microsecond value. When trying to increase the value of STARTUP in Register AT91_ADC_MR some higher values can't be reached. Change the type in function parameter and private structure field from u8 to u32. Signed-off-by:
Jan Leupold <leupold@rsi-elektrotechnik.de> [nicolas.ferre@atmel.com: change commit message, increase u16 to u32 for startup time] Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> [-js: only change at91_adc_state for 3.12]
-
JM Friedt authored
commit adfa9698 upstream. The value sent on the SPI bus is shifted by an erroneous number of bits. The shift value was already computed in the iio_chan_spec structure and hence subtracting this argument to 16 yields an erroneous data position in the SPI stream. Signed-off-by:
JM Friedt <jmfriedt@femto-st.fr> Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Cyrille Pitchen authored
commit 93563a6a upstream. For TX transactions, the TXCOMP bit in the Status Register is cleared when the first data is written into the Transmit Holding Register. In the lines from at91_do_twi_transfer(): at91_twi_write_data_dma(dev); at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); the TXCOMP interrupt may be enabled before the DMA controller has actually started to write into the THR. In such a case, the TXCOMP bit is still set into the Status Register so the interrupt is triggered immediately. The driver understands that a transaction completion has occurred but this transaction hasn't started yet. Hence the TXCOMP interrupt is no longer enabled by at91_do_twi_transfer() but instead by at91_twi_write_data_dma_callback(). Also, the TXCOMP bit in the Status Register in not a clear on read flag but a snapshot of the transmission state at the time the Status Register is read. When a NACK error is dectected by the I2C controller, the TXCOMP, NACK and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP interrupt is triggered at the same time. Also setting the TXRDY to 1 triggers the DMA controller to write the next data into the THR. Such a write resets the TXCOMP bit to 0 in the SR. So depending on when the interrupt handler reads the SR, it may fail to detect the NACK error if it relies on the TXCOMP bit. The NACK bit and its interrupt should be used instead. For RX transactions, the TXCOMP bit in the Status Register is cleared when the START bit is set into the Control Register. However to unify the management of the TXCOMP bit when the DMA controller is used, the TXCOMP interrupt is now enabled by the DMA callbacks for both TX and RX transfers. Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Joseph Qi authored
commit 6f6a6fda upstream. If updating journal superblock fails after journal data has been flushed, the error is omitted and this will mislead the caller as a normal case. In ocfs2, the checkpoint will be treated successfully and the other node can get the lock to update. Since the sb_start is still pointing to the old log block, it will rewrite the journal data during journal recovery by the other node. Thus the new updates will be overwritten and ocfs2 corrupts. So in above case we have to return the error, and ocfs2_commit_cache will take care of the error and prevent the other node to do update first. And only after recovering journal it can do the new updates. The issue discussion mail can be found at: https://oss.oracle.com/pipermail/ocfs2-devel/2015-June/010856.html http://comments.gmane.org/gmane.comp.file-systems.ext4/48841 [ Fixed bug in patch which allowed a non-negative error return from jbd2_cleanup_journal_tail() to leak out of jbd2_fjournal_flush(); this was causing xfstests ext4/306 to fail. -- Ted ] Reported-by:
Yiwen Jiang <jiangyiwen@huawei.com> Signed-off-by:
Joseph Qi <joseph.qi@huawei.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Tested-by:
-
Dmitry Monakhov authored
commit b4f1afcd upstream. jbd2_cleanup_journal_tail() can be invoked by jbd2__journal_start() So allocations should be done with GFP_NOFS [Full stack trace snipped from 3.10-rh7] [<ffffffff815c4bd4>] dump_stack+0x19/0x1b [<ffffffff8105dba1>] warn_slowpath_common+0x61/0x80 [<ffffffff8105dcca>] warn_slowpath_null+0x1a/0x20 [<ffffffff815c2142>] slab_pre_alloc_hook.isra.31.part.32+0x15/0x17 [<ffffffff8119c045>] kmem_cache_alloc+0x55/0x210 [<ffffffff811477f5>] ? mempool_alloc_slab+0x15/0x20 [<ffffffff811477f5>] mempool_alloc_slab+0x15/0x20 [<ffffffff81147939>] mempool_alloc+0x69/0x170 [<ffffffff815cb69e>] ? _raw_spin_unlock_irq+0xe/0x20 [<ffffffff8109160d>] ? finish_task_switch+0x5d/0x150 [<ffffffff811f1a8e>] bio_alloc_bioset+0x1be/0x2e0 [<ffffffff8127ee49>] blkdev_issue_flush+0x99/0x120 [<ffffffffa019a733>] jbd2_cleanup_journal_tail+0x93/0xa0 [jbd2] -->GFP_KERNEL [<ffffffffa019aca1>] jbd2_log_do_checkpoint+0x221/0x4a0 [jbd2] [<ffffffffa019afc7>] __jbd2_log_wait_for_space+0xa7/0x1e0 [jbd2] [<ffffffffa01952d8>] start_this_handle+0x2d8/0x550 [jbd2] [<ffffffff811b02a9>] ? __memcg_kmem_put_cache+0x29/0x30 [<ffffffff8119c120>] ? kmem_cache_alloc+0x130/0x210 [<ffffffffa019573a>] jbd2__journal_start+0xba/0x190 [jbd2] [<ffffffff811532ce>] ? lru_cache_add+0xe/0x10 [<ffffffffa01c9549>] ? ext4_da_write_begin+0xf9/0x330 [ext4] [<ffffffffa01f2c77>] __ext4_journal_start_sb+0x77/0x160 [ext4] [<ffffffffa01c9549>] ext4_da_write_begin+0xf9/0x330 [ext4] [<ffffffff811446ec>] generic_file_buffered_write_iter+0x10c/0x270 [<ffffffff81146918>] __generic_file_write_iter+0x178/0x390 [<ffffffff81146c6b>] __generic_file_aio_write+0x8b/0xb0 [<ffffffff81146ced>] generic_file_aio_write+0x5d/0xc0 [<ffffffffa01bf289>] ext4_file_write+0xa9/0x450 [ext4] [<ffffffff811c31d9>] ? pipe_read+0x379/0x4f0 [<ffffffff811b93f0>] do_sync_write+0x90/0xe0 [<ffffffff811b9b6d>] vfs_write+0xbd/0x1e0 [<ffffffff811ba5b8>] SyS_write+0x58/0xb0 [<ffffffff815d4799>] system_call_fastpath+0x16/0x1b Signed-off-by:
Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by:
-
Michal Hocko authored
commit 7444a072 upstream. ext4_free_blocks is looping around the allocation request and mimics __GFP_NOFAIL behavior without any allocation fallback strategy. Let's remove the open coded loop and replace it with __GFP_NOFAIL. Without the flag the allocator has no way to find out never-fail requirement and cannot help in any way. Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Eryu Guan authored
commit 8974fec7 upstream. Currently ext4_ind_migrate() doesn't correctly handle a file which contains a hole at the beginning of the file. This caused the migration to be done incorrectly, and then if there is a subsequent following delayed allocation write to the "hole", this would reclaim the same data blocks again and results in fs corruption. # assmuing 4k block size ext4, with delalloc enabled # skip the first block and write to the second block xfs_io -fc "pwrite 4k 4k" -c "fsync" /mnt/ext4/testfile # converting to indirect-mapped file, which would move the data blocks # to the beginning of the file, but extent status cache still marks # that region as a hole chattr -e /mnt/ext4/testfile # delayed allocation writes to the "hole", reclaim the same data block # again, results in i_blocks corruption xfs_io -c "pwrite 0 4k" /mnt/ext4/testfile umount /mnt/ext4 e2fsck -nf /dev/sda6 ... Inode 53, i_blocks is 16, should be 8. Fix? no ... Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
-
Eryu Guan authored
commit d6f123a9 upstream. Currently the check in ext4_ind_migrate() is not enough before doing the real conversion: a) delayed allocated extents could bypass the check on eh->eh_entries and eh->eh_depth This can be demonstrated by this script xfs_io -fc "pwrite 0 4k" -c "pwrite 8k 4k" /mnt/ext4/testfile chattr -e /mnt/ext4/testfile where testfile has two extents but still be converted to non-extent based file format. b) only extent length is checked but not the offset, which would result in data lose (delalloc) or fs corruption (nodelalloc), because non-extent based file only supports at most (12 + 2^10 + 2^20 + 2^30) blocks This can be demostrated by xfs_io -fc "pwrite 5T 4k" /mnt/ext4/testfile chattr -e /mnt/ext4/testfile sync If delalloc is enabled, dmesg prints EXT4-fs warning (device dm-4): ext4_block_to_path:105: block 1342177280 > max in inode 53 EXT4-fs (dm-4): Delayed block allocation failed for inode 53 at logical offset 1342177280 with max blocks 1 with error 5 EXT4-fs (dm-4): This should not happen!! Data will be lost If delalloc is disabled, e2fsck -nf shows corruption Inode 53, i_size is 5497558142976, should be 4096. Fix? no Fix the two issues by a) forcing all delayed allocation blocks to be allocated before checking eh->eh_depth and eh->eh_entries b) limiting the last logical block of the extent is within direct map Signed-off-by:
-
Lukas Czerner authored
commit 9705acd6 upstream. On delalloc enabled file system on invalidatepage operation in ext4_da_page_release_reservation() we want to clear the delayed buffer and remove the extent covering the delayed buffer from the extent status tree. However currently there is a bug where on the systems with page size > block size we will always remove extents from the start of the page regardless where the actual delayed buffers are positioned in the page. This leads to the errors like this: EXT4-fs warning (device loop0): ext4_da_release_space:1225: ext4_da_release_space: ino 13, to_free 1 with only 0 reserved data blocks This however can cause data loss on writeback time if the file system is in ENOSPC condition because we're releasing reservation for someones else delayed buffer. Fix this by only removing extents that corresponds to the part of the page we want to invalidate. This problem is reproducible by the following fio receipt (however I was only able to reproduce it with fio-2.1 or older. [global] bs=8k iodepth=1024 iodepth_batch=60 randrepeat=1 size=1m directory=/mnt/test numjobs=20 [job1] ioengine=sync bs=1k direct=1 rw=randread filename=file1:file2 [job2] ioengine=libaio rw=randwrite direct=1 filename=file1:file2 [job3] bs=1k ioengine=posixaio rw=randwrite direct=1 filename=file1:file2 [job5] bs=1k ioengine=sync rw=randread filename=file1:file2 [job7] ioengine=libaio rw=randwrite filename=file1:file2 [job8] ioengine=posixaio rw=randwrite filename=file1:file2 [job10] ioengine=mmap rw=randwrite bs=1k filename=file1:file2 [job11] ioengine=mmap rw=randwrite direct=1 filename=file1:file2 Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Darrick J. Wong authored
commit 292db1bc upstream. ext4 isn't willing to map clusters to a non-extent file. Don't signal this with an out of space error, since the FS will retry the allocation (which didn't fail) forever. Instead, return EUCLEAN so that the operation will fail immediately all the way back to userspace. (The fix is either to run e2fsck -E bmap2extent, or to chattr +e the file.) Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Theodore Ts'o authored
commit 89d96a6f upstream. Normally all of the buffers will have been forced out to disk before we call invalidate_bdev(), but there will be some cases, where a file system operation was aborted due to an ext4_error(), where there may still be some dirty buffers in the buffer cache for the device. So try to force them out to memory before calling invalidate_bdev(). This fixes a warning triggered by generic/081: WARNING: CPU: 1 PID: 3473 at /usr/projects/linux/ext4/fs/block_dev.c:56 __blkdev_put+0xb5/0x16f() Signed-off-by:
-
Theodore Ts'o authored
commit bdf96838 upstream. The commit cf108bca: "ext4: Invert the locking order of page_lock and transaction start" caused __ext4_journalled_writepage() to drop the page lock before the page was written back, as part of changing the locking order to jbd2_journal_start -> page_lock. However, this introduced a potential race if there was a truncate racing with the data=journalled writeback mode. Fix this by grabbing the page lock after starting the journal handle, and then checking to see if page had gotten truncated out from under us. This fixes a number of different warnings or BUG_ON's when running xfstests generic/086 in data=journalled mode, including: jbd2_journal_dirty_metadata: vdc-8: bad jh for block 115643: transaction (ee3fe7 c0, 164), jh->b_transaction ( (null), 0), jh->b_next_transaction ( (null), 0), jlist 0 - and - kernel BUG at /usr/projects/linux/ext4/fs/jbd2/transaction.c:2200! ... Call Trace: [<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117 [<c02b2de5>] __ext4_journalled_invalidatepage+0x10f/0x117 [<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117 [<c027d883>] ? lock_buffer+0x36/0x36 [<c02b2dfa>] ext4_journalled_invalidatepage+0xd/0x22 [<c0229139>] do_invalidatepage+0x22/0x26 [<c0229198>] truncate_inode_page+0x5b/0x85 [<c022934b>] truncate_inode_pages_range+0x156/0x38c [<c0229592>] truncate_inode_pages+0x11/0x15 [<c022962d>] truncate_pagecache+0x55/0x71 [<c02b913b>] ext4_setattr+0x4a9/0x560 [<c01ca542>] ? current_kernel_time+0x10/0x44 [<c026c4d8>] notify_change+0x1c7/0x2be [<c0256a00>] do_truncate+0x65/0x85 [<c0226f31>] ? file_ra_state_init+0x12/0x29 - and - WARNING: CPU: 1 PID: 1331 at /usr/projects/linux/ext4/fs/jbd2/transaction.c:1396 irty_metadata+0x14a/0x1ae() ... Call Trace: [<c01b879f>] ? console_unlock+0x3a1/0x3ce [<c082cbb4>] dump_stack+0x48/0x60 [<c0178b65>] warn_slowpath_common+0x89/0xa0 [<c02ef2cf>] ? jbd2_journal_dirty_metadata+0x14a/0x1ae [<c0178bef>] warn_slowpath_null+0x14/0x18 [<c02ef2cf>] jbd2_journal_dirty_metadata+0x14a/0x1ae [<c02d8615>] __ext4_handle_dirty_metadata+0xd4/0x19d [<c02b2f44>] write_end_fn+0x40/0x53 [<c02b4a16>] ext4_walk_page_buffers+0x4e/0x6a [<c02b59e7>] ext4_writepage+0x354/0x3b8 [<c02b2f04>] ? mpage_release_unused_pages+0xd4/0xd4 [<c02b1b21>] ? wait_on_buffer+0x2c/0x2c [<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8 [<c02b5a5b>] __writepage+0x10/0x2e [<c0225956>] write_cache_pages+0x22d/0x32c [<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8 [<c02b6ee8>] ext4_writepages+0x102/0x607 [<c019adfe>] ? sched_clock_local+0x10/0x10e [<c01a8a7c>] ? __lock_is_held+0x2e/0x44 [<c01a8ad5>] ? lock_is_held+0x43/0x51 [<c0226dff>] do_writepages+0x1c/0x29 [<c0276bed>] __writeback_single_inode+0xc3/0x545 [<c0277c07>] writeback_sb_inodes+0x21f/0x36d ... Signed-off-by:
-
Haggai Eran authored
commit cab46214 upstream. With an RTL8191SU USB adaptor, sometimes the hints for a fragmented packet are set, but the packet length is too large. Allocate enough space to prevent memory corruption and a resulting kernel panic [1]. [1] http://www.spinics.net/lists/linux-wireless/msg136546.htmlSigned-off-by:
Haggai Eran <haggai.eran@gmail.com> ACKed-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Felix Fietkau authored
commit 300f77c0 upstream. AR93xx and newer needs to stop rx before tx to avoid getting the DMA engine or MAC into a stuck state. This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Marcel Holtmann authored
commit ecffc804 upstream. The SKB returned from the Intel specific version information command is missing a kfree_skb. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
