Commits · dcef0d06b34a80071da4496556e85f9bf3b3c0bf · Kirill Smelkov / linux

23 Feb, 2012 1 commit

PCI: Disable cardbus bridge MEM1 prefetchable bit · dcef0d06

Yinghai Lu authored Feb 10, 2012

Some BIOSes enable prefetch on both MEM0 and MEM1.  But the cardbus code
assumes MEM1 is non-pref...

Discussion could be found at:
	https://lkml.org/lkml/2012/1/12/1
	https://bugzilla.kernel.org/show_bug.cgi?id=41622#c23Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

dcef0d06

17 Feb, 2012 3 commits

PCI / PM: Disable wakeup during shutdown for devices not enabled to wake up · 5b415f1e

Rafael J. Wysocki authored Feb 07, 2012

If a PCI device is enabled to generate wakeup signals (PME) when put
into a low-power state by runtime PM, it will be still enabled to
generate those signals after the system shutdown, unless its driver's
.shutdown() callback takes care of the wakeup signals generation
setting.  Moreover, there are devices that are not enabled to wake
up the system and that are configured by runtime PM to generate
wakeup signals so that (runtime) remote wakeup works with them.
Those devices should be reconfigured during system shutdown so that
they don't generate wakeup signals, but at least some drivers don't
do that.  However, that very well may be done by the PCI core so
that drivers don't have to worry about it.  For this reason, modify
pci_device_shutdown() to disable the generation of wakeup events for
devices not supposed to wake up the system.

References: https://bugzilla.kernel.org/show_bug.cgi?id=37952Reported-and-tested-by: Kamil Iskra <kamil.54002@iskra.name>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

5b415f1e

PCI: Fix /sys warning when sriov enabled and card is hot removed · 09cedbef

Yinghai Lu authored Feb 04, 2012

sysfs is a bit stricter now and emits warnings in more cases.

For SRIOV hotplug, we are calling pci_stop_dev() for each VF first
(after we update pci_stop_bus_devices) which remove each VF subdir.  So
double check the VF dir in /sys before trying to remove the physfn link.
Signed-of-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

09cedbef

PCI: pcie: Add support for setting default ASPM policy · ad71c962

Matthew Garrett authored Feb 03, 2012

Distributions may wish to provide different defaults for PCIE ASPM
depending on their target audience. Provide a configuration option for
choosing the default policy.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

ad71c962

14 Feb, 2012 36 commits

PCI: Add quirk for still enabled interrupts on Intel Sandy Bridge GPUs · f67fd55f

Thomas Jarosch authored Dec 07, 2011

Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.

These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.

Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.

Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
  Probably the IRQ ends up somewhere unnoticed.

According to reports on the net, the Intel DH61WW board is also affected.

Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: Charlie Suffin <charlie.suffin@stratus.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

f67fd55f

PCI: Annotate PCI quirks in initcall_debug style · 3209874a

Arjan van de Ven authored Jan 30, 2012

While diagnosing some boot time issues on a platform, all that I
could see in the bootgraph/dmesg was that the system was spending
a lot of time in applying one or more PCI quirks... which
was virtually undebuggable.

This patch adds printk's in "initcall_debug" style to the dmesg,
which are added when the user asks for the initcall_debug
(the nr one tool to use when debugging boot hangs or boot time issues)
kernel command line option.

v2: add #includes so quirks can build on non-x86
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

3209874a

PCI hotplug: cpcihp: fix debug module parameter to be bool · 309c6651

Danny Kukawka authored Jan 30, 2012

Fix debug variable from module parameter to be really bool to
fix 'warning: return from incompatible pointer type'.
Acked-by: Scott Murray <scott@spiteful.org>
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

309c6651

PCI: check for pci bar restore completion and retry · 26f41062

Kay, Allen M authored Jan 26, 2012

On some OEM systems, pci_restore_state() is called while FLR has not yet
completed.  As a result, PCI BAR register restore is not successful.  This fix
reads back the restored value and compares it with saved value and re-tries 10
times before giving up.
Signed-off-by: Jean Guyader <jean.guyader@eu.citrix.com>
Signed-off-by: Eric Chanudet <eric.chanudet@citrix.com>
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

26f41062

PCI: pciehp: Disable/enable link during slot power off/on · 2debd928

Yinghai Lu authored Jan 27, 2012

On a system with a repeater on the system board to support gen2 hotplug,
we found that when an ExpressModule is removed from some slots,
/var/log/messages will be full of "card present/not present" warnings.

It turns out the root complex is continually trying to train the link to
the repeater because the repeater has not been reset.

This patch will disable the link at removal time to allow the repeater
to be reset properly.  This also prevents a potential AER message at
removal time.

Also, when testing hotplug on a system under development, we found if we
boot the system without an EM installed, and later hot-add an EM, it
does not work with Linux, but another OS is ok.  The root cause is that
BIOS left link disabled when slot was empty at boot time, and other OS
is modifying the link disable bit in link ctrl during power on/off.

So we should do the same thing to disable/enable link during power off/on.

-v2: check link DLLA bit instead of 100ms waiting.
     Separate link disable/enable functions to another patch.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

2debd928

PCI: pciehp: Add Disable/enable link functions · 7f822999

Yinghai Lu authored Jan 27, 2012

Will use it during power off/on of slots
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

7f822999

PCI: pciehp: Add pcie_wait_link_not_active() · bffe4f72

Yinghai Lu authored Jan 27, 2012

Will use it for link disable status checking.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

bffe4f72

PCI: pciehp: make check_link_active more helpful · 4e2ce405

Yinghai Lu authored Jan 27, 2012

A few changes:
  - remove the 'inline' and let the complier decide
  - return a bool to indicate whether the link was active
  - add a debug message to indicate link state when it beocmes active
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

4e2ce405

PCI: pciehp: replace unconditional sleep with config space access check · 2f5d8e4f

Yinghai Lu authored Jan 27, 2012

During reviewing
|	PCI: pciehp: wait 1000 ms before Link Training check
Linus said:
>...
> That's a *long* time, and it's irritating to the user. It makes the
> user think "the machine is slow".
>...
> And quite frankly, an unconditional one-second delay here seems bad.
>Two seconds was unacceptable, one second is just bad.

Try to access the pci conf of a pci device that is supposed to show up
in 1s.  If we can read back a valid vendor/device id, we can return
early.

Related discussion could be found:
	https://lkml.org/lkml/2011/12/6/339

-v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device()
    and reuse it from pciehp code. Suggested by Matthew Wilcox.
-v3: According to Kenj, don't use array in stack, and don't wait too long
    for crs, also return fail status if not found.
    Also separate pci_bus_dev_read_vendor_id() change to another patch.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

2f5d8e4f

PCI: Separate pci_bus_read_dev_vendor_id from pci_scan_device · efdc87da

Yinghai Lu authored Jan 27, 2012

We can reuse it for pciehp probing.

-v2: according to Kenji, fix crs timeout checking, and export the function
     for later use when pciehp is compiled as a module.
Suggested-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

efdc87da

PCI: make sriov work with hotplug remove · ac205b7b

Yinghai Lu authored Jan 27, 2012

When hot removing a pci express module that has a pcie switch and supports
SRIOV, we got:

[ 5918.610127] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 1
[ 5918.615779] pciehp 0000:80:02.2:pcie04: Attention button interrupt received
[ 5918.622730] pciehp 0000:80:02.2:pcie04: Button pressed on Slot(3)
[ 5918.629002] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 1f9
[ 5918.637416] pciehp 0000:80:02.2:pcie04: PCI slot #3 - powering off due to button press.
[ 5918.647125] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 10
[ 5918.653039] pciehp 0000:80:02.2:pcie04: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 5918.661229] pciehp 0000:80:02.2:pcie04: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
[ 5924.667627] pciehp 0000:80:02.2:pcie04: Disabling domain:bus:device=0000:b0:00
[ 5924.674909] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 2f9
[ 5924.683262] pciehp 0000:80:02.2:pcie04: pciehp_unconfigure_device: domain:bus:dev = 0000:b0:00
[ 5924.693976] libfcoe_device_notification: NETDEV_UNREGISTER eth6
[ 5924.764979] libfcoe_device_notification: NETDEV_UNREGISTER eth14
[ 5924.873539] libfcoe_device_notification: NETDEV_UNREGISTER eth15
[ 5924.995209] libfcoe_device_notification: NETDEV_UNREGISTER eth16
[ 5926.114407] sxge 0000:b2:00.0: PCI INT A disabled
[ 5926.119342] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 5926.127189] IP: [<ffffffff81353a3b>] pci_stop_bus_device+0x33/0x83
[ 5926.133377] PGD 0
[ 5926.135402] Oops: 0000 [#1] SMP
[ 5926.138659] CPU 2
[ 5926.140499] Modules linked in:
...
[ 5926.143754]
[ 5926.275823] Call Trace:
[ 5926.278267]  [<ffffffff81353a38>] pci_stop_bus_device+0x30/0x83
[ 5926.284180]  [<ffffffff81353af4>] pci_remove_bus_device+0x1a/0xba
[ 5926.290264]  [<ffffffff81366311>] pciehp_unconfigure_device+0x110/0x17b
[ 5926.296866]  [<ffffffff81365dd9>] ? pciehp_disable_slot+0x188/0x188
[ 5926.303123]  [<ffffffff81365d6f>] pciehp_disable_slot+0x11e/0x188
[ 5926.309206]  [<ffffffff81365e68>] pciehp_power_thread+0x8f/0xe0
...

 +-[0000:80]-+-00.0-[81-8f]--
 |           +-01.0-[90-9f]--
 |           +-02.0-[a0-af]--
 |           +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Device
 |           |                               |            +-00.1 Device
 |           |                               |            +-00.2 Device
 |           |                               |            \-00.3 Device
 |           |                               \-03.0-[b3]--+-00.0 Device
 |           |                                            +-00.1 Device
 |           |                                            +-00.2 Device
 |           |                                            \-00.3 Device

root complex: 80:02.2
pci express modules: have pcie switch and are listed as b0:00.0, b1:02.0 and b1:03.0.
end devices  are b2:00.0 and b3.00.0.
VFs are: b2:00.1,... b2:00.3, and b3:00.1,...,b3:00.3

Root cause: when doing pci_stop_bus_device() with phys fn, it will stop
virt fn and remove the fn, so
	list_for_each_safe(l, n, &bus->devices)
will have problem to refer freed n that is pointed to vf entry.

Solution is just replacing list_for_each_safe() with
list_for_each_prev_safe().  This will make sure we can get valid n pointer
to PF instead of the freed VF pointer (because newly added devices are
inserted to the bus->devices list tail).

During reviewing the patch, Bjorn said:
|   The PCI hot-remove path calls pci_stop_bus_devices() via
|   pci_remove_bus_device().
|
|   pci_stop_bus_devices() traverses the bus->devices list (point A below),
|   stopping each device in turn, which calls the driver remove() method.  When
|   the device is an SR-IOV PF, the driver calls pci_disable_sriov(), which
|   also uses pci_remove_bus_device() to remove the VF devices from the
|   bus->devices list (point B).
|
|       pci_remove_bus_device
|         pci_stop_bus_device
|           pci_stop_bus_devices(subordinate)
|             list_for_each(bus->devices)             <-- A
|               pci_stop_bus_device(PF)
|                 ...
|                   driver->remove
|                     pci_disable_sriov
|                       ...
|                         pci_remove_bus_device(VF)
|                             <remove from bus_list>  <-- B
|
|   At B, we're changing the same list we're iterating through at A, so when
|   the driver remove() method returns, the pci_stop_bus_devices() iterator has
|   a pointer to a list entry that has already been freed.

Discussion thread can be found : https://lkml.org/lkml/2011/10/15/141
				 https://lkml.org/lkml/2012/1/23/360

-v5: According to Linus to make remove more robust, Change to
     list_for_each_prev_safe instead. That is more reasonable, because
     those devices are added to tail of the list before.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

ac205b7b

PCI: remove add_to_failed_list() · 67cc7e26