Merge all chip type specific prefixed (rtl2831u_ and rtl2832u_)
callback to top level callback prefixed as rtl28xxu_.

rtl2831u_foo() => rtl28xxu_foo()
rtl2832u_foo() => rtl28xxu_foo()
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Detect automatically whether chip is old RTL2831U or newer
RTL2832U/RTL2832P. Detection is based I2C command that is found only
from newer RTL2832U models.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Buffer needed for USB control message is small so move it to state
and get rid of alloc/free used for each control message.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Pass correct device pointer to dev_* logging in order to print
module name and bus id correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

I prefer dev over priv and I want keep all my drivers in line with
that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

There was 2 muxed I2C adapters, one for demod tuner bus and one for
internal use. Idea of internal I2C adapter was to force I2C repeater
close when demod access its registers. Driver has also delayed work
queue based method to close I2C repeater.

After regmap conversion internal I2C adapter based repeater close
left unused - only work queue method was in use. We could not use
internal mux adapter method with regmap as it makes recursive regmap
call, which causes deadlock as regmap has own locking. Due to that
remove whole method totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

We are consumer of DVB frontend provided by rtl28xxu module. Due to
that we must use refcount to ensure none could remove rtl28xxu when
we are alive (or when we are streaming, if more fine-grained
refcounting is wanted).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This driver, rtl28xxu, offers frontend service for rtl2832_sdr
module, thus we are producer and rtl2832_sdr module is consumer.
Due to that, reference counting should be done in way rtl2832_sdr
takes refrence to rtl28xxu. Remove wrong refcount.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Logic is so simple that there is no idea to separate tuner selection to
own function, instead do it in a callback and get rid of one function.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVB FE callback functionality went broken after I moved tuners to
demod muxed I2C adapter. That happens because driver state was
carried by I2C adapter and when mux is used there is one adapter
more in a chain.
USB adapter <-> I2C adapter <-> muxed I2C adapter
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Put demod to soft reset in order to save power when sleep. That drops
power usage ~30mA @5V on USB dongle I tested. In real life it does
not matter much as USB IF powers off demod too, but now it is done
twice - demod and USB IF.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

I have implemented tons of things for that driver, more than anyone
else, so lets claim copyright and module authorship.

Cc: Thomas Mair <thomas.mair86@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove all the stuff that is not needed anymore. Rename variable.
Remove extra new lines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Small cleanups. Remove unneeded variables. Some checkpatch issues.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Pass correct device, platform device, for logging system in order
to format printouts correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Both mn88472 and mn88473 slave demods are connected to master I2C
bus, not the bus behind master demod I2C gate like tuners. Use
correct bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

RTL2832 SDR module implements kernel platform driver. Change old
binding to that one.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

That SDR driver module was abusing DVB frontend SEC (satellite
equipment controller) device and due to that it was also using
legacy DVB binding. Platform bus is pseudo-bus provided by kernel
driver model and it fits cases like that, where any other busses
are not suitable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

'dev' sounds better than 's' for such variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Provide register read and write callbacks for SDR module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Chips uses 8-bit register addresses with 5 pages. Extend register
address by using register page as a first byte of address, defining
virtual register addresses. That is common method of handling
register pages and regmap also uses it. Remove page + address
conversion glue which was there for regmap.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

There is no need to do software reset on init() as it is done a bit
later on end of set_frontend(). Software reset usually means
restarting (resetting to starting point) chip internal state machine
(FSM). Naturally it is done after all parameters are programmed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Enable regmap register cache in order to reduce IO.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

RTL2832 demod integrated into RTL2832U has PID filter. PID filtering
is provided by rtl2832 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement PID filter. This demod has PID filter size of 32 PIDs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Demod lock flags are derived from demod state machine states. States
are running from 1 to 11, where highest state 11 means demod is
fully locked and streaming. Naturally smaller state numbers means
there is some partial locks.

Define now state 10 as missing synch and lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

We don't need it anymore as all users are using muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Tuners are connected to demod I2C adapter. Use that muxed adapter
for each tuner. That allows us to get rid of hackish FE gate control
solution.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Estimate signal strength from IF digital AGC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read BER to return values calculated by DVBv5
statistics.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read SNR to return values calculated by DVBv5
statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 BER.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 CNR.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use regmap to cover register access routines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use platform data configuration for rtl2832 demod driver. Old
configuration are still left as it is used for rtl2832_sdr driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Move all needed configuration values to platform data structure
and remove old configuration code where possible.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Pass correct device pointer to dev_* logging functions in order
print logs correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Rename it device state variable to dev. Both priv and dev are very
common terms for such variable in kernel, but I like use dev in
order to keep drivers consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Exported resources are not needed anymore as all users are using
callbacks carried via platform data. Due to that we will remove
those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Switch demod resource use from exported symbols to callbacks its
provides.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>