If building a kernel without FTRACE but with TRACING, dwc3.ko fails to
link due to missing trace events. Fix this by using the correct
Kconfig symbol on Makefile.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In

	dwc3_request	*r = NULL;
	r = A;

the first assignment has no effect. Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistake in dev_warn warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In the following test we get stuck by sleeping forever in _dwc3_set_mode()
after which dual-role switching doesn't work.

On dra7-evm's dual-role port,
- Load g_zero gadget driver and enumerate to host
- suspend to mem
- disconnect USB cable to host and connect otg cable with Pen drive in it.
- resume system
- we sleep indefinitely in _dwc3_set_mode due to.
  dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()->
	dwc3_gadget_stop()->wait_event_lock_irq()

To fix this instead of waiting indefinitely with wait_event_lock_irq()
we use wait_event_interruptible_lock_irq_timeout() and print
and error message if there was a timeout.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Declared dwc2_force_mode() function as static, because it was used
only in core.c file, for fixing sparse error.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds a way to enable an external vbus supply in host mode,
when dwc2 drvvbus signal is not used.

This patch is very similar to the one done in U-Boot dwc2 driver [1]. It
also adds dynamic vbus supply management depending on the role and state
of the core.

[1] https://lists.denx.de/pipermail/u-boot/2017-March/283434.htmlSigned-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.

The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.

If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.

Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.

Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().

Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Enable the power down option based on the core capability.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Affected cases:
ClearPortFeature's
 USB_PORT_FEAT_SUSPEND

SetPortFeature's
 USB_PORT_FEAT_SUSPEND
 USB_PORT_FEAT_RESET
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The GPWRDN interrupts are those that occur in both Host and
Device mode while core is in hibernated state.

Export dwc2_core_init to be able to use it in GPWRDN_IDSTS
interrupt handler.

Here we have duplicated init functions in host and gadget sides
so I have left things as it was(used corresponing functions for
host and gadget), maybe in the future we'll resolve this problem
and will use dwc2_core_init for both sides.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Do changes to allow entering hibernated state from USB_SUSPEND
interrupt. All code is added under if conditions and mustn't impact
existing functionality.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

These are wrapper functions which are calling device or host
enter/exit hibernation functions.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add host/device hibernation functions which must be wrapped
by core's  dwc2_enter_hibernation()/dwc2_exit_hibernation()
functions.

Make dwc2_backup_global_registers dwc2_restore_global_register
non-static to use them in both host/gadget sides.

Added function names:
dwc2_gadget_enter_hibernation()
dwc2_gadget_exit_hibernation()
dwc2_host_enter_hibernation()
dwc2_host_exit_hibernation()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add common (host/device) helper functions, which will be called while
exiting from hibernation, from both sides.

dwc2_restore_essential_regs()
dwc2_hib_restore_common()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Move hptxfsiz to host register's backup/restore functions, not
needed to have it in global register's backup/restore functions.

Add backup for glpmcfg, and read/write for gi2cctl and pcgcctl.
As requires programming guide.

Affected functions:
dwc2_backup_host_registers()
dwc2_restore_host_registers()
dwc2_backup_global_registers()
dwc2_restore_global_registers()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It will be set once corresponding set_feature command comes.

True if device is allowed to wake-up host by remote-wakeup
signalling.

This is preparation for remote wake-up support implementation,
it will not be implemented until gadget stack provide interface
for bringing remote wake-up signalling.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added a flag to indicate that core is in hibernation,
it is used to determine the hibernation state of the core.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add parameter remote_wakeup to dwc2_restore_device_registers()
to be able to restore device registers according to programming
guide for dwc-otg. It says that in case of rem_wakeup DCTL must not
be restored here.

Remove setting of DCTL_PWRONPRGDONE from this function, because it
will be done in function responsible for exiting from hibernation.

WA for enabled EPx's IN and OUT in DDMA mode. On entering to
hibernation wrong value read and saved from DIEPDMAx,
as result BNA interrupt asserted on hibernation exit
by restoring from saved area.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Moved dtxfsiz from dwc2_gregs_backup to dwc2_dregs_backup,
because it is device register.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add parameter and it's initialization, needed for hibernation.

Reimplement dwc2_set_param_power_down() to support hibernation too.
Now 'power_down' parameter can be initialized with 0, 1 or 2.
0 - No
1 - Partial power down
2 - Hibernation
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

No-op change, only rename.

This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.

Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Set 'lpm_capable' flag in the gadget structure so
indicating that LPM is supported.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This is useful on platforms (e.g. TI AM437x) that don't
have ID available on a GPIO but do have the OTG block.

We can obtain the ID state via the OTG block and use it
for dual-role switching.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This fixes "utmi_phy_clk_enable: timeout waiting for phy to stabilize"
error message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The nop_reset and shutdown methods are called in a context that can sleep,
so use gpiod_set_value_cansleep instead of gpiod_set_value.

If you've connected the reset line to a GPIO expander, you'd get a kernel
"slowpath" warning with gpiod_set_value.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The show() method should use scnprintf() not snprintf() because snprintf()
may returns a value that exceeds its second argument.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We don't support PRTCAP == OTG yet, so prevent user from
setting it via debugfs.

Fixes: 41ce1456 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add OTG and GHWPARAMS6 register definitions
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Amlogic Meson GXL and AXG SoCs come with a (host-only) dwc3 USB
controller. To use this controller a clock has to be enabled and a reset
line has to be pulsed.
Enabling the clock works identical to other SoCs. However, the reset
line has to be pulsed (using reset_control_reset) instead of using a
level reset (reset_control_{assert,deassert}).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some SoCs (such as Amlogic Meson GXL for example) share the reset line
with other components (in case of the Meson GXL example there's a shared
reset line between the USB2 PHYs, USB3 PHYs and the dwc3 controller).
Additionally SoC implementations may prefer a reset pulse over level
resets.

For now this falls back to the old defaults, which are:
- reset lines are exclusive
- level resets are being used
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Amlogic Meson GX SoCs (GXL and AXG) come with a (host-only) dwc3 USB
controller. This requires a clock to be enabled and a reset line to be
pulsed to get the hardware into a known state.
Add the documentation for this IP block, similar to "qcom,dwc3.txt".
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Assign true or false to boolean variables instead of an integer value.

This issue was detected with the help of Coccinelle.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added core state checking in dwc2_hsotg_ep_queue() function
to make sure that application will submit requests only in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added call_gadget() function call when entering to L1 state
to inform gadget that core is in L1 state.

Did the same thing when exiting from L1 state
to inform gadget that core is in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Configure core in device mode to support LPM according to
programming guide.
Device will start giving valid responses for LPM tokens.
After this patch device side LPM will start working.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Enable "LPM Transaction Received" interrupt for receive an
interrupt when host will send LPM token.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This interrupt indicates that an LPM transaction
was received on the USB bus. After getting this
interrupt we are going from L0 state to L1 state.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a function which will be called if device is in L1 sleep state
and Resume/Remote Wakeup Detected interrupt is asserted.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make field names of GLPMCFG register in definitions to be
the same with the databook.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>