Quite a few of the existing supported chips that use
mv88e6085_g1_ieee_pri_map as ->ieee_pri_map (including, incidentally,
mv88e6085 itself) actually have a reset value of 0xfa50 in the
G1_IEEE_PRI register.

The data sheet for the mv88e6095, however, does describe a reset value
of 0xfa41.

So rather than changing the value in the existing callback, introduce
a new variant with the 0xfa50 value. That will be used by the upcoming
mv88e6250, and existing chips can be switched over one by one,
preferably double-checking both the data sheet and actual hardware in
each case - if anybody actually feels this is important enough to
care.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when rx csum is disabled, vmxnet3 driver does not turn
off lro, which can cause performance issues if user does not turn off
lro explicitly. This patch adds fix_features support which is used to
turn off LRO whenever RXCSUM is disabled.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Rishi Mehta <rmehta@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: add struct nexthop to fib{6}_info

Set 10 of 11 to improve route scalability via support for nexthops as
standalone objects for fib entries.
    https://lwn.net/Articles/763950/

This sets adds 'struct nexthop' to fib_info and fib6_info. IPv4
already handles multiple fib_nh entries in a single fib_info, so
the conversion to use a nexthop struct is fairly mechanical. IPv6
using a nexthop struct with a fib6_info impacts a lot of core logic
which is built around the assumption of a single, builtin fib6_nh
per fib6_info. To make this easier to review, this set adds
nexthop to fib6_info and adds checks in most places fib6_info is
used. The next set finishes the IPv6 conversion, walking through
the places that need to consider all fib6_nh within a nexthop struct.

Offload drivers - mlx5, mlxsw and rocker - are changed to fail FIB
entries using nexthop objects. That limitation can be removed once
the drivers are updated to properly support separate nexthops.

This set starts by adding accessors for fib_nh and fib_nhs in a
fib_info. This makes it easier to extract the number of nexthops
in the fib entry and a specific fib_nh once the entry references
a struct nexthop. Patch 2 converts more of IPv4 code to use
fib_nh_common allowing a struct nexthop to use a fib6_nh with an
IPv4 entry.

Patches 3 and 4 add 'struct nexthop' to fib{6}_info and update
references to both take a different path when it is set. New
exported functions are added to the nexthop code to validate a
nexthop struct when configured for use with a fib entry. IPv4
is allowed to use a nexthop with either v4 or v6 entries. IPv6
is limited to v6 entries only. In both cases list_heads track
the fib entries using a nexthop struct for fast correlation on
events (e.g., device events or nexthop events like delete or
replace).

The last 3 patches add hooks to drivers listening for FIB
notificationas. All 3 of them reject the routes as unsupported,
returning an error message to the user via extack. For mlxsw
at least this is a stop gap measure until the driver is updated for
proper support.

Functional tests for nexthops have already been committed. Those tests
will be active after the next patch set which makes the code paths
created by this set and the next one live.

Existing code paths moved to the else branch of 'if (f{6}i->nh)' checks
are covered by existing tests under selftests/net.

v3
- remove ip6_create_rt_rcu from ip6_pol_route in patch 4 and use pcpu
  routes for REJECT routes with the blackhole nexthop (request from Wei)

v2
- no code changes from v1
- commit messages for first 4 patches updated
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add struct nexthop and nh_list list_head to fib6_info. nh_list is the
fib6_info side of the nexthop <-> fib_info relationship. Since a fib6_info
referencing a nexthop object can not have 'sibling' entries (the old way
of doing multipath routes), the nh_list is a union with fib6_siblings.

Add f6i_list list_head to 'struct nexthop' to track fib6_info entries
using a nexthop instance. Update __remove_nexthop_fib to walk f6_list
and delete fib entries using the nexthop.

Add a few nexthop helpers for use when a nexthop is added to fib6_info:
- nexthop_fib6_nh - return first fib6_nh in a nexthop object
- fib6_info_nh_dev moved to nexthop.h and updated to use nexthop_fib6_nh
  if the fib6_info references a nexthop object
- nexthop_path_fib6_result - similar to ipv4, select a path within a
  multipath nexthop object. If the nexthop is a blackhole, set
  fib6_result type to RTN_BLACKHOLE, and set the REJECT flag

Update the fib6_info references to check for nh and take a different path
as needed:
- rt6_qualify_for_ecmp - if a fib entry uses a nexthop object it can NOT
  be coalesced with other fib entries into a multipath route
- rt6_duplicate_nexthop - use nexthop_cmp if either fib6_info references
  a nexthop
- addrconf (host routes), RA's and info entries (anything configured via
  ndisc) does not use nexthop objects
- fib6_info_destroy_rcu - put reference to nexthop object
- fib6_purge_rt - drop fib6_info from f6i_list
- fib6_select_path - update to use the new nexthop_path_fib6_result when
  fib entry uses a nexthop object
- rt6_device_match - update to catch use of nexthop object as a blackhole
  and set fib6_type and flags.
- ip6_route_info_create - don't add space for fib6_nh if fib entry is
  going to reference a nexthop object, take a reference to nexthop object,
  disallow use of source routing
- rt6_nlmsg_size - add space for RTA_NH_ID
- add rt6_fill_node_nexthop to add nexthop data on a dump

As with ipv4, most of the changes push existing code into the else branch
of whether the fib entry uses a nexthop object.

Update the nexthop code to walk f6i_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 'struct nexthop' and nh_list list_head to fib_info. nh_list is the
fib_info side of the nexthop <-> fib_info relationship.

Add fi_list list_head to 'struct nexthop' to track fib_info entries
using a nexthop instance. Add __remove_nexthop_fib and add it to
__remove_nexthop to walk the new list_head and mark those fib entries
as dead when the nexthop is deleted.

Add a few nexthop helpers for use when a nexthop is added to fib_info:
- nexthop_cmp to determine if 2 nexthops are the same
- nexthop_path_fib_result to select a path for a multipath
  'struct nexthop'
- nexthop_fib_nhc to select a specific fib_nh_common within a
  multipath 'struct nexthop'

Update existing fib_info_nhc to use nexthop_fib_nhc if a fib_info uses
a 'struct nexthop', and mark fib_info_nh as only used for the non-nexthop
case.

Update the fib_info functions to check for fi->nh and take a different
path as needed:
- free_fib_info_rcu - put the nexthop object reference
- fib_release_info - remove the fib_info from the nexthop's fi_list
- nh_comp - use nexthop_cmp when either fib_info references a nexthop
  object
- fib_info_hashfn - use the nexthop id for the hashing vs the oif of
  each fib_nh in a fib_info
- fib_nlmsg_size - add space for the RTA_NH_ID attribute
- fib_create_info - verify nexthop reference can be taken, verify
  nexthop spec is valid for fib entry, and add fib_info to fi_list for
  a nexthop
- fib_select_multipath - use the new nexthop_path_fib_result to select a
  path when nexthop objects are used
- fib_table_lookup - if the 'struct nexthop' is a blackhole nexthop, treat
  it the same as a fib entry using 'blackhole'

The bulk of the changes are in fib_semantics.c and most of that is
moving the existing change_nexthops into an else branch.

Update the nexthop code to walk fi_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert more IPv4 code to use fib_nh_common over fib_nh to enable routes
to use a fib6_nh based nexthop. In the end, only code not using a
nexthop object in a fib_info should directly access fib_nh in a fib_info
without checking the famiy and going through fib_nh_common. Those
functions will be marked when it is not directly evident.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use helpers to access fib_nh and fib_nhs fields of a fib_info. Drop the
fib_dev macro which is an alias for the first nexthop. Replacements:

  fi->fib_dev    --> fib_info_nh(fi, 0)->fib_nh_dev
  fi->fib_nh     --> fib_info_nh(fi, 0)
  fi->fib_nh[i]  --> fib_info_nh(fi, i)
  fi->fib_nhs    --> fib_info_num_path(fi)

where fib_info_nh(fi, i) returns fi->fib_nh[nhsel] and fib_info_num_path
returns fi->fib_nhs.

Move the existing fib_info_nhc to nexthop.h and define the new ones
there. A later patch adds a check if a fib_info uses a nexthop object,
and defining the helpers in nexthop.h avoid circular header
dependencies.

After this all remaining open coded references to fi->fib_nhs and
fi->fib_nh are in:
- fib_create_info and helpers used to lookup an existing fib_info
  entry, and
- the netdev event functions fib_sync_down_dev and fib_sync_up.

The latter two will not be reused for nexthops, and the fib_create_info
will be updated to handle a nexthop in a fib_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit had an unintended side effect with reject routes:
rt6i_pcpu is expected to always be initialized for all fib6_info except
the null entry. The commit mentioned below skips it for reject routes
and ends up leaking references to the loopback device. For example,

    ip netns add foo
    ip -netns foo li set lo up
    ip -netns foo -6 ro add blackhole 2001:db8:1::1
    ip netns exec foo ping6 2001:db8:1::1
    ip netns del foo

ends up spewing:
    unregister_netdevice: waiting for lo to become free. Usage count = 3

The fib_nh_common_init is not needed for reject routes (no ipv4 caching
or encaps), so move the alloc_percpu_gfp after it and adjust the goto label.

Fixes: f40b6ae2 ("ipv6: Move pcpu cached routes to fib6_nh")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds LRO support for the HiNIC driver.
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ariel Levkovich says:

====================
Support MPLS features in bonding and vlan net devices

Netdevice HW MPLS features are not passed from device driver's netdevice to
upper netdevice, specifically VLAN and bonding netdevice which are created
by the kernel when needed.

This prevents enablement and usage of HW offloads, such as TSO and checksumming
for MPLS tagged traffic when running via VLAN or bonding interface.

The patches introduce changes to the initialization steps of the VLAN and bonding
netdevices to inherit the MPLS features from lower netdevices to allow the HW
offloads.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

During the creation of the VLAN interface net device,
the various device features and offloads are being set based
on the parent device's features.
The code initiates the basic, vlan and encapsulation features
but doesn't address the MPLS features set and they remain blank.
As a result, all device offloads that have significant performance
effect are disabled for MPLS traffic going via this VLAN device such
as checksumming and TSO.

This patch makes sure that MPLS features are also set for the
VLAN device based on the parent which will allow HW offloads of
checksumming and TSO to be performed on MPLS tagged packets.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting the bonding interface net device features,
the kernel code doesn't address the slaves' MPLS features
and doesn't inherit them.

Therefore, HW offloads that enhance performance such as
checksumming and TSO are disabled for MPLS tagged traffic
flowing via the bonding interface.

The patch add the inheritance of the MPLS features from the
slave devices with a similar logic to setting the bonding device's
VLAN and encapsulation features.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net/tls: small general improvements

This series cleans up and improves the tls code, mostly the offload
parts.

First a slight performance optimization - avoiding unnecessary re-
-encryption of records in patch 1.  Next patch 2 makes the code
more resilient by checking for errors in skb_copy_bits().  Next
commit removes a warning which can be triggered in normal operation,
(especially for devices explicitly making use of the fallback path).
Next two paths change the condition checking around the call to
tls_device_decrypted() to make it easier to extend.  Remaining
commits are centered around reorganizing struct tls_context for
better cache utilization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

All callers pass prot->version as the last parameter
of tls_advance_record_sn(), yet tls_advance_record_sn()
itself needs a pointer to prot.  Pass prot from callers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct tls_context is slightly badly laid out.  If we reorder things
right we can save 16 bytes (320 -> 304) but also make all fast path
data fit into two cache lines (one read only and one read/write,
down from four cache lines).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ctx->prot holds the same information as per-direction contexts.
Almost all code gets TLS version from this structure, convert
the last two stragglers, this way we can improve the cache
utilization by moving the per-direction data into cold cache lines.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tls_device_decrypted() is only called from decrypt_skb_update(),
when ctx->decrypted == false, there is no need to re-check the bit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the RX config of a TLS socket is SW, there is no point iterating
over the fragments and checking if frame is decrypted.  It will
always be fully encrypted.  Note that in fully encrypted case
the function doesn't actually touch any offload-related state,
so it's safe to call for TLS_SW, today.  Soon we will introduce
code which can only be called for offloaded contexts.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's possible that TCP stack will decide to retransmit a packet
right when that packet's data gets acked, especially in presence
of packet reordering.  This means that packets may be in flight,
even though tls_device code has already freed their record state.
Make fill_sg_in() and in turn tls_sw_fallback() not generate a
warning in that case, and quietly proceed to drop such frames.

Make the exit path from tls_sw_fallback() drop monitor friendly,
for users to be able to troubleshoot dropped retransmissions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In light of recent bugs, we should make a better effort of
checking return values.  In theory none of the functions should
fail today.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If strparser gets cornered into starting a new message from
an sk_buff which already has frags, it will allocate a new
skb to become the "wrapper" around the fragments of the
message.

This new skb does not inherit any metadata fields.  In case
of TLS offload this may lead to unnecessarily re-encrypting
the message, as skb->decrypted is not set for the wrapper skb.

Try to be conservative and copy all fields of old skb
strparser's user may reasonably need.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang warns:

drivers/net/ethernet/mscc/ocelot_ace.c:335:37: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
        struct ocelot_vcap_u64 payload = { 0 };
                                           ^
                                           {}
drivers/net/ethernet/mscc/ocelot_ace.c:336:28: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
        struct vcap_data data = { 0 };
                                  ^
                                  {}
drivers/net/ethernet/mscc/ocelot_ace.c:683:37: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
        struct ocelot_ace_rule del_ace = { 0 };
                                           ^
                                           {}
drivers/net/ethernet/mscc/ocelot_ace.c:743:28: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
        struct vcap_data data = { 0 };
                                  ^
                                  {}
4 warnings generated.

One way to fix these warnings is to add additional braces like Clang
suggests; however, there has been a bit of push back from some
maintainers[1][2], who just prefer memset as it is unambiguous, doesn't
depend on a particular compiler version[3], and properly initializes all
subobjects. Do that here so there are no more warnings.

[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
[3]: https://lore.kernel.org/lkml/20181116150432.2408a075@redhat.com/

Fixes: b5962294 ("net: mscc: ocelot: Add support for tcam")
Link: https://github.com/ClangBuiltLinux/linux/issues/505Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot triggered following splat when strict netlink
validation is enabled:

net/ipv4/devinet.c:1766 suspicious rcu_dereference_check() usage!

This occurs because we hold RTNL mutex, but no rcu read lock.
The second call site holds both, so just switch to the _rtnl variant.

Reported-by: syzbot+bad6e32808a3a97b1515@syzkaller.appspotmail.com
Fixes: 2638eb8b ("net: ipv4: provide __rcu annotation for ifa_list")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
expose flash update status to user

When user is flashing device using devlink, he currenly does not see any
information about what is going on, percentages, etc.
Drivers, for example mlxsw and mlx5, have notion about the progress
and what is happening. This patchset exposes this progress
information to userspace.

Example output for existing flash command:
$ devlink dev flash pci/0000:01:00.0 file firmware.bin
Preparing to flash
Flashing 100%
Flashing done

See this console recording which shows flashing FW on a Mellanox
Spectrum device:
https://asciinema.org/a/247926

Please see individual patches for changelog.
v2->v3 only adds tags and the last selftest patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Utilizes the devlink flash code.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement mlxfw status_notify op by passing notification down to
devlink. Also notify about flash update begin and end.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new op status_notify which is called to update the user about
flashing status.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a function to be called from drivers during flash. It sends
notification to userspace about flash update progress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the error messages are printed to dmesg. Propagate them also
to directly to user doing the flashing through extack.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Benefit from the devlink flash update implementation and ethtool
fallback to it and move firmware flash implementation there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Benefit from the devlink flash update implementation and ethtool
fallback to it and move firmware flash implementation there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add option for enabling RMII phy mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wei Liang Lim <wei.liang.lim@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
FDB updates for SJA1105 DSA driver

This patch series adds:

- FDB switchdev support for the second generation of switches (P/Q/R/S).
  I could test/code these now that I got a board with a SJA1105Q.

- Management route support for SJA1105 P/Q/R/S. This is needed to send
  PTP/STP/management frames over the CPU port.

- Logic to hide private DSA VLANs from the 'bridge fdb' commands.

The new FDB code was also tested and still works on SJA1105T.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

TX VLANs and RX VLANs are an internal implementation detail of DSA for
frame tagging.  They work by installing special VLANs on switch ports in
the operating modes where no behavior change w.r.t. VLANs can be
observed by the user.

Therefore it makes sense to hide these VLANs in the 'bridge fdb'
command, as well as translate the pvid into the RX VID and TX VID on
'bridge fdb add' and 'bridge fdb del' commands.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic patch that simplifies the code by removing a
redundant check. A logical AND-with-zero performed on a zero is still
zero.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for manipulating the L2 forwarding database (dump,
add, delete) for the second generation of NXP SJA1105 switches.

At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>