Replace custom type ssi_fips_state_t with underlying enum.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace custom type ssi_fips_error_t with underlying enum.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace references to type tdes_keys_t with struct tdes_keys.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix location of pointer in variables definitions and dereference.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove explicit comparisons to NULL in ccree driver.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix mismatched braces between if and else.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix several cases of needless braces around single statement blocks.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant blank lines in brace blocks
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix cases where the else clause was not located correctly after the if
brace.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix cases in ccree where explicit comparsion to true/false
was made.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add and/or remove redundant and/or missing spaces in ccree source
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Start holding the lock for all cases irrespective of number of fb,
there could be a deadlock since this number could change in the
lifetime of this lock
Signed-off-by: Dhananjay Balan <mail@dbalan.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch introduces new module parameter, dev, which takes a string
representing the device that the external synth is connected to, e.g.
ttyS0, ttyUSB0 etc. This is then used to communicate with the synth.
That way, speakup can support more than ttyS*. As of this patch, it
only supports ttyS*, ttyUSB* and selected synths for lp*. dev parameter
is only available for tty-migrated synths.

Users will either use dev or ser as both serve same purpose. This patch
maintains backward compatility by allowing ser to be specified. When
both are specified, whichever is non-default, i.e. not ttyS0, is used.
If both are non-default then dev is used.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds functionality to validate and convert either a device
name or 'ser' memmber of synth into dev_t. Subsequent patch in this set
will call it to convert user-specified device into device number. For
device name, this patch does some basic sanity checks on the string
passed in. It currently supports ttyS*, ttyUSB* and, for selected
synths, lp*.

The patch also introduces a string member variable named 'dev_name' to
struct spk_synth. 'dev_name' represents the device name - ttyUSB0 etc -
which needs conversion to dev_t.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function converts strings like ttyS0 and ttyUSB0 to dev_t like
(4, 64) and (188, 0). It does this by scanning tty_drivers list for
corresponding device name and index. If the driver is not registered,
this function returns -ENODEV. It also acquires tty_mutex.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit bb4a64b7.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit c6ce019e.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 48d3cfb3.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit be6faff7.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 10a8593a.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b32cdde1.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 7eba570e.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit af437671.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b065307f.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 5776aad3.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 7d6e221d.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 9b1aa455.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 1877e4ba.

The whole series is broken, so back it all out.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of IIO new device support, features and cleanups for the 4.13 cycle.

A few reverts here. One was a general failure to notice a device was already
supported by another driver.  The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.

Reverts
* bma180
  - Revert addition of support for the BMA250E it is already supported by
    the bmc150-accel and better supported at that. Oops.
* hi8435
  - The fix for cleanup of the reset gpio stuff isn't a good way to go.  It
    breaks systems where an inverting level convertor is used.  The right fix
    is to make the original devicetree correct - even if it involves patching
    the devicetree in kernel.

New Device Support
* stm32-adc
  - STM32H7 support and bindings.

Features
* core
  - add a hardware triggered operating mode for systems in which the actual
    trigger is never seen by the kernel.  This is typically only used when
    a device 'can' use other triggers, but if a particular magic one is
    enabled the interrupt is effectively handled in hardware and we never see
    it.
* st-lsm6dsx
  - support active low interrupts.
* stm32-adc
  - Make the core adc clock optional as not all hardware supported requires it.
  - Make the bus clock optional in the per instance driver as it may be shared
    by all instances of the ADC and is handled by the core.
  - Rework to have a data structure representing the device type specific
    elements.
* stm32-trigger (and counter)
  - Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
  - Add an attribute to configure device modes for quadrature counting etc.

Clean ups and minor fixes
* IIO core.
  - use __sysfs_match_string() helper rather than open coding the same.
* ad7791
  - use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
  - handle return value of clk_prepare_enable
* cpcap
  - Fix default register values and ensure the battery thermistor is enabled
    correctly.
  - Fix the reported die temperature where we can - docs are lacking.
  - Remove the hung interrupt quirk as no longer happens due to fix in the
    mfd driver.
* hi8435
  - Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
  - Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
  - Make the use of iio_info_mask* elements consistent for all channels.
    This doesn't have any visible effect, but acts as clear documentation of
    which channels various resulting attributes apply to.
* lpc32xx
  - handle the return value of clk_prepare_enable.
* meson-saradc
  - NULL instead of 0 for pointer.
* mma9551
  - use NULL for GPIO connection ID to aid implementation fo ACPI support.
    Here the connection ID doesn't actually tell us anything and it is much
    easier to deal with the driver if it's not there.
* mpu6050
  - Fix lock issues through use of a local mux.
  - Replace sprintf with scnprintf as appropriate.
  - Check whoami against all known values.  This allows for a small number of
    boards where we are really fishing for the part not being present at all.
    It is unfortunately common to have undescribed changes to use newer chips.
    We paper over this but just emitting a warning for those cases as long as
    we know about.
* mxs-lradc
  - Fix some non static warnings.
* rcar-adc
  - Part of making the naming for this part consistent across the kernel.
* st_accel
  - drop some spi_device_id entries for variants with no SPI support
* st_magn
  - drop some spi_device_id entries for variants with no SPI support.
* sx9500
  - Use devm_gpiod_get instead of indexed value with an index of 0 on all
    occasions.
* twl4030
  - Drop unused twl4030_get_madc_conversion as callers removed now throughout
    kernel.
  - Unexport twl4030_madc_conversion() as no used only within this driver.
  - Drop twl4030_madc_user_params as not used now.
  - Drop twl4030_madc_request.func_cb as not used now.
  - Fold the twl4030-madc.h header into the driver as no longer used anywhere
    else in the kernel.
* xilinx
  - Handle the return value of clk_prepare_enable

This patch adds definition of tty_open_by_driver when CONFIG_TTY is not
defined. This was supposed to have been included in commit
12e84c71 ("tty: export
tty_open_by_driver"). The patch follows convention for other such
functions and returns NULL.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

synths[] array caches currently loaded synths. synth_add checks
synths[] before adding a new one. It however ignores the result of
do_synth_init. So when do_synth_init fails, the failed synth is still
cached. Since, as a result module loading fails too, synth_remove -
which is responsible for removing the cached synth - is never called.
Next time the failing synth is added again it succeeds because
synth_add finds it cached inside synths[].

This patch fixes this by caching a synth only after do_synth_init
succeeds.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CHECK: Macro argument reuse 'pframe' - possible side-effects?

Convert get_tofr_ds macro to inline functions to fix checkpatch check
Signed-off-by: Jaya Durga <rjdurga@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch.pl warnings of the form "function definition argument
'foo' should also have an identifier name" in header files.
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed checkpatch.pl warnings of "function definition argument FOO should
also have an identifier name"
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed checkpatch.pl warnings of the form "function definition argument
'foo' should also have an identifier name" in header files.
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed checkpatch warnings "Use #include <linux/FOO> instead of <asm/FOO>"
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed style of permissions to octal.
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix multiple style issues (CHECK spaces preferred around that $operator).
Signed-off-by: Galo Navarro <anglor@varoa.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We were waiting for a completion notification of HW DMA
operation using an interruptible wait which can result
in data corruption if a signal interrupted us while
DMA was not yet completed.

Fix this by moving to uninterrupted wait.

Fixes: abefd674 ("staging: ccree: introduce CryptoCell HW driver").
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ccree driver has build time configurable support
to work on top of coherent (e.g. ACP) vs. none coherent bus
connections. Turn it to run-time configurable option
based on device tree.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>