- 30 Nov, 2022 10 commits
-
-
Pali Rohár authored
If there's no PCI host bridge with ISA then check for PCI host bridge with alias "pci0" (first PCI host bridge) and if it exists then choose it as the primary PCI host bridge. This makes choice of primary PCI host bridge more stable across boots and updates as the last fallback candidate for primary PCI host bridge (if there is no choice) is selected arbitrary. Signed-off-by:
Pali Rohár <pali@kernel.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220820123327.20551-1-pali@kernel.org
-
Pali Rohár authored
Channel 0 of SA56004ED chip refers to internal SA56004ED chip sensor (chip itself is located on the board) and channel 1 of SA56004ED chip refers to external sensor which is connected to temperature diode of the P2020 CPU. Fixes: 54c15ec3 ("powerpc: dts: Add DTS file for CZ.NIC Turris 1.x routers") Signed-off-by:
Marek Behún <kabel@kernel.org> Signed-off-by:
-
Thomas Weißschuh authored
Commit 7ad4bd88 ("powerpc/book3e: get rid of #include <generated/compile.h>") removed the usage of the define UTS_RELEASE but forgot to drop the include. utsrelease.h is potentially generated on each build. By removing the unused include we can get rid of some spurious recompilations. Fixes: 7ad4bd88 ("powerpc/book3e: get rid of #include <generated/compile.h>") Signed-off-by:
Thomas Weißschuh <linux@weissschuh.net> Reviewed-by:
Masahiro Yamada <masahiroy@kernel.org> Reviewed-by:
Christophe Leroy <christophe.leroy@csgroup.eu> [mpe: Fix typo in change log and add more explanation] Signed-off-by:
-
Naveen N. Rao authored
For systemwide tests, use online cpu mask to only open events on online cpus. This enables this test to work on systems in lower SMT modes. Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by:
-
Naveen N. Rao authored
The systemwide perf hardware breakpoint test tries to open a perf event on each cpu. On large systems, we run out of file descriptors and fail the test. Instead, have the test set the file descriptor limit to an arbitraty high value. Reported-by:
Rohan Deshpande <rohan_d@linux.vnet.ibm.com> Signed-off-by:
-
Naveen N. Rao authored
Right now, if perf_event_open() fails for the systemwide tests, error report is printed too late, sometimes after subsequent system calls. Move use of perror() to the main function, just after the syscall. Signed-off-by:
-
Christoph Hellwig authored
ps3_system_bus_type is only used inside of system-bus.c, so remove the external declaration and the very outdated comment next to it. Signed-off-by:
Christoph Hellwig <hch@lst.de> Acked-by:
Geoff Levand <geoff@infradead.org> Signed-off-by:
-
Michael Ellerman authored
Merge our fixes branch to bring in some changes that are prerequisites for work in next.
-
Michael Ellerman authored
Merge our KVM topic branch.
-
Nicholas Piggin authored
32-bit does not trace_irqs_off() to match the trace_irqs_on() call in kvmppc_fix_ee_before_entry(). This can lead to irqs being enabled twice in the trace, and the irqs-off region between guest exit and the host enabling local irqs again is not properly traced. 64-bit code does call this, but from asm code where volatiles are live and so incorrectly get clobbered. Move the irq reconcile into C to fix both problems. Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
- 25 Nov, 2022 1 commit
-
-
Michael Ellerman authored
There's no declaration for machine_check_early_boot(), which leads to a build failure with W=1. Add one. Fixes: 2f5182cf ("powerpc/64s: early boot machine check handler") Signed-off-by:
-
- 24 Nov, 2022 29 commits
-
-
Tiezhu Yang authored
The latest version of grep claims the egrep is now obsolete so the build now contains warnings that look like: egrep: warning: egrep is obsolescent; using grep -E fix this up by moving the related file to use "grep -E" instead. sed -i "s/egrep/grep -E/g" `grep egrep -rwl arch/powerpc` Here are the steps to install the latest grep: wget http://ftp.gnu.org/gnu/grep/grep-3.8.tar.gz tar xf grep-3.8.tar.gz cd grep-3.8 && ./configure && make sudo make install export PATH=/usr/local/bin:$PATH Signed-off-by:
Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by:
-
Nayna Jain authored
Even though plpks_read_var() is currently called to read variables owned by different consumers, it internally supports only OS consumer. Fix plpks_read_var() to handle different consumers correctly. Fixes: 2454a7af ("powerpc/pseries: define driver for Platform KeyStore") Signed-off-by:
Nayna Jain <nayna@linux.ibm.com> Signed-off-by:
-
Nayna Jain authored
Replace kmalloc with kzalloc in construct_auth() function to default initialize structure with zeroes. Signed-off-by:
-
Nayna Jain authored
Logging H_CALL return codes in PLPKS driver are easy to confuse with Linux error codes. Let the caller of the function log the converted linux error code. Signed-off-by:
-
Nayna Jain authored
Some commands for eg. "cat" might continue to retry on encountering EINTR. This is not expected for original error code H_ABORTED. Map H_ABORTED to more relevant Linux error code EIO. Fixes: 2454a7af ("powerpc/pseries: define driver for Platform KeyStore") Signed-off-by:
-
Nayna Jain authored
PAPR Spec defines H_P1 actually as H_PARAMETER and maps H_ABORTED to a different numerical value. Fix the error codes as per PAPR Specification. Fixes: 2454a7af ("powerpc/pseries: define driver for Platform KeyStore") Signed-off-by:
-
Nayna Jain authored
OS_VAR_LINUX enum in PLPKS driver should be 0x02 instead of 0x01. Fixes: 2454a7af ("powerpc/pseries: define driver for Platform KeyStore") Signed-off-by:
-
Chen Lifu authored
1. ppc_override_l2cr and ppc_override_l2cr_value are only used in l2cr_init() function, remove them and used *l2cr directly. 2. has_l2cache is not used outside of the file, so mark it static and do not initialise statics to 0. Fixes the following warnings: arch/powerpc/platforms/powermac/setup.c:73:5: warning: symbol 'ppc_override_l2cr' was not declared. Should it be static? arch/powerpc/platforms/powermac/setup.c:74:5: warning: symbol 'ppc_override_l2cr_value' was not declared. Should it be static? arch/powerpc/platforms/powermac/setup.c:75:5: warning: symbol 'has_l2cache' was not declared. Should it be static? Signed-off-by:
Chen Lifu <chenlifu@huawei.com> Reviewed-by:
-
Bo Liu authored
Fixes the following W=1 kernel build warning(s): arch/powerpc/platforms/pseries/eeh_pseries.c:163: warning: Function parameter or member 'config_addr' not described in 'pseries_eeh_phb_reset' arch/powerpc/platforms/pseries/eeh_pseries.c:163: warning: Excess function parameter 'config_adddr' description in 'pseries_eeh_phb_reset' arch/powerpc/platforms/pseries/eeh_pseries.c:198: warning: Function parameter or member 'config_addr' not described in 'pseries_eeh_phb_configure_bridge' arch/powerpc/platforms/pseries/eeh_pseries.c:198: warning: Excess function parameter 'config_adddr' description in 'pseries_eeh_phb_configure_bridge' Signed-off-by:
Bo Liu <liubo03@inspur.com> Signed-off-by:
-
Russell Currey authored
In hw_breakpoint_handler(), ea is set by wp_get_instr_detail() except for 8xx, leading the variable to be passed uninitialised to wp_check_constraints(). This is safe as wp_check_constraints() returns early without using ea, so just set it to make the compiler happy. Signed-off-by:
Russell Currey <ruscur@russell.cc> Reviewed-by:
-
Shaomin Deng authored
Remove the repeated word "not" in comments. Signed-off-by:
Shaomin Deng <dengshaomin@cdjrlc.com> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a perror message. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
Naveen N. Rao authored
preempt_enable_no_resched() is just the same as preempt_enable() when we are in a irqs disabled context. kprobe_handler() and the post/fault handlers are all called with irqs disabled. As such, convert those to just use preempt_enable(). Reported-by:
-
Naveen N. Rao authored
Similar to x86 commit 2e62024c ("kprobes/x86: Use preempt_enable() in optimized_callback()"), change powerpc optprobes to use preempt_enable() rather than preempt_enable_no_resched() since powerpc also removed irq disabling for optprobes in commit f72180cc ("powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace"). Reported-by:
-
Naveen N. Rao authored
arch_prepare_kprobe() is called from register_kprobe() via prepare_kprobe(), or through register_aggr_kprobe(), both with the kprobe_mutex held. Per the comment for get_kprobe(): /* * This routine is called either: * - under the 'kprobe_mutex' - during kprobe_[un]register(). * OR * - with preemption disabled - from architecture specific code. */ As such, there is no need to disable preemption around the call to get_kprobe(). Drop the same. Reported-by:
-
ruanjinjie authored
When build Linux kernel, encounter the following warnings: ./arch/powerpc/sysdev/mpic_msgr.c:230:38: warning: cast removes address space '__iomem' of expression ./arch/powerpc/sysdev/mpic_msgr.c:230:27: warning: incorrect type in assignment (different address spaces) The data type of msgr->mer and msgr->base are 'u32 __iomem *', but converted to 'u32 *' and 'u8 *' directly and cause above warnings, now instead of using a type cast, change the size of the pointer offset to fix these warnings. Signed-off-by:
ruanjinjie <ruanjinjie@huawei.com> Reviewed-by:
-
Yang Yingliang authored
If remapping 'data->trig_page' fails, the 'data->eoi_mmio' need be unmapped before returning from xive_spapr_populate_irq_data(). Fixes: eac1e731 ("powerpc/xive: guest exploitation of the XIVE interrupt controller") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Cédric Le Goater <clg@kaod.org> Signed-off-by:
-
Stephen Rothwell authored
This is a follow on from commit 0d362be5 ("Makefile: link with -z noexecstack --no-warn-rwx-segments") for arch/powerpc/boot to address wanrings like: ld: warning: opal-calls.o: missing .note.GNU-stack section implies executable stack ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker ld: warning: arch/powerpc/boot/zImage.epapr has a LOAD segment with RWX permissions This fixes issue https://github.com/linuxppc/issues/issues/417Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Christophe JAILLET authored
At the beginning of the file, we have: #define pr_fmt(fmt) "xive: " fmt So, there is no need to duplicate "XIVE:" in debug and error messages. For the records, these useless prefix have been added in commit 5af50993 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Nicholas Piggin authored
cputime_t was a core kernel type, removed by commits ed5c8c85..b672592f. As explained in commit b672592f ("sched/cputime: Remove generic asm headers"), the final cleanup is for the arch to provide cputime_to_nsec[s](). Commit ade7667a ("powerpc: Add cputime_to_nsecs()") did that, but justdidn't remove the then-unused cputime_to_usecs(), cputime_t type, and associated remnants. Signed-off-by:
-
Michael Ellerman authored
Although the previous commit made the powerpc instruction dump usable with scripts/decodecode, there are still some problems. Because the dump is split across multiple lines, the script doesn't cope with printk timestamps or caller info. That can be fixed by printing the entire dump on one line, eg: [ 12.016307][ T112] --- interrupt: c00 [ 12.016605][ T112] Code: 4b7aae15 60000000 3d22016e 3c62ffec 39291160 38639bc0 e8890000 4b7aadf9 60000000 4bfffee8 7c0802a6 60000000 <0fe00000> 60420000 3c4c008f 384268a0 [ 12.017655][ T112] ---[ end trace 0000000000000000 ]--- That output can then be piped directly into scripts/decodecode and interpreted correctly. Printing the dump on a single line does produce a very long line, about 173 characters. That is still shorter than x86, which prints nearly 200 characters even without timestamps etc. All consoles I'm aware of will wrap the line if it's too long, so the length should not be a functional problem. If anything it should help on consoles like VGA by using less vertical space. Signed-off-by:
-
Michael Ellerman authored
Matt reported that scripts/decodecode doesn't work for the instruction dump in the powerpc oops output. Although there are scripts around that can decode it, it would be preferable if the standard in-tree script worked. All other arches prefix the instruction dump with "Code:", and that's what the script looks for, so use that. The script then works as expected: $ CROSS_COMPILE=powerpc64le-linux-gnu- ./scripts/decodecode Code: fbc1fff0 f821ffc1 7c7d1b78 7c9c2378 ebc30028 7fdff378 48000018 60000000 60000000 ebff0008 7c3ef840 41820048 <815f0060> e93f0000 5529077c 7d295378 ^D All code ======== 0: f0 ff c1 fb std r30,-16(r1) 4: c1 ff 21 f8 stdu r1,-64(r1) 8: 78 1b 7d 7c mr r29,r3 ... Note that the script doesn't cope well with printk timestamps or printk caller info. Reported-by:Matthew Wilcox <willy@infradead.org> Signed-off-by:
-
Joel Stanley authored
This is the register layout of the litesd peripheral for the fusesoc based Microwatt SoC. It requires a description of the system clock, which is hardcoded to 100MHz. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
-
Christophe Leroy authored
At the time being, with 16k pages __set_pte_at() writes table entries in reverse order: 294: 91 49 00 0c stw r10,12(r9) 298: 91 49 00 08 stw r10,8(r9) 29c: 91 49 00 04 stw r10,4(r9) 2a0: 91 49 00 00 stw r10,0(r9) Allthough there should be no impact at all as it stays in a single cacheline, reverse the writing in a more natural order. 288: 91 49 00 0c stw r10,0(r9) 28c: 91 49 00 08 stw r10,4(r9) 290: 91 49 00 04 stw r10,8(r9) 294: 91 49 00 00 stw r10,12(r9) Signed-off-by:
-
Christophe Leroy authored
While looking at code generated for code patching, I saw that pte_clear generated: 2d8: 38 a0 00 00 li r5,0 2dc: 38 e0 10 00 li r7,4096 2e0: 39 00 20 00 li r8,8192 2e4: 39 40 30 00 li r10,12288 2e8: 90 a9 00 00 stw r5,0(r9) 2ec: 90 e9 00 04 stw r7,4(r9) 2f0: 91 09 00 08 stw r8,8(r9) 2f4: 91 49 00 0c stw r10,12(r9) With 16k pages, only the first entry is used by the kernel, so no need to adapt the address of other entries. Only duplicate the first entry for hardware. Now it is: 2cc: 39 40 00 00 li r10,0 2d0: 91 49 00 00 stw r10,0(r9) 2d4: 91 49 00 04 stw r10,4(r9) 2d8: 91 49 00 08 stw r10,8(r9) 2dc: 91 49 00 0c stw r10,12(r9) Signed-off-by:
-
Dmitry Torokhov authored
This patch converts the driver to newer gpiod API, and away from OF-specific legacy gpio API that we want to stop using. While at it, let's address a few more issues: - switch to using dev_info()/pr_info() and friends - cancel work when unbinding the driver Note that the original code handled halt GPIO polarity incorrectly: in halt callback, when line polarity is "low" it would set trigger to "1" and drive halt line high, which is counter to the annotation. gpiod API will drive such line low. However I do not see any DTSes in mainline that have a DT node with "sgy,gpio-halt" compatible. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Dmitry Torokhov authored
This switches PIKA Warp away from legacy gpio API and to newer gpiod API, so that we can eventually deprecate the former. Because LEDs are normally driven by leds-gpio driver, but the platform code also wants to access the LEDs during thermal shutdown, and gpiod API does not allow locating GPIO without requesting it, the platform code is now responsible for locating GPIOs through device tree and requesting them. It then constructs platform data for leds-gpio platform device and registers it. This allows platform code to retain access to LED GPIO descriptors and use them when needed. Signed-off-by:
-
Gustavo A. R. Silva authored
When building with automatic stack variable initialization, GCC 12 complains about variables defined outside of switch case statements. Move the variable into the case that uses it, which silences the warning: arch/powerpc/xmon/xmon.c: In function ‘bpt_cmds’: arch/powerpc/xmon/xmon.c:1529:13: warning: statement will never be executed [-Wswitch-unreachable] 1529 | int mode; | ^~~~ Fixes: 09b6c112 ("powerpc/xmon: Fix compile error with PPC_8xx=y") Signed-off-by:Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Kajol Jain authored
Commit 57dc0eed ("KVM: PPC: Book3S HV P9: Implement PMU save/restore in C") removed the PMU save/restore functions from assembly code and implemented these functions in C, for power9 and later platforms. After the code refactoring, Performance Monitoring Unit (PMU) registers became part of "p9_host_os_sprs" structure and now this structure is used to save/restore pmu host registers, for power9 and later platfroms. But we still have old unused registers references. Patch removes unused host_mmcr references for Monitor Mode Control Register 3 (MMCR3)/ Sampled Instruction Event Register 2 (SIER2)/ SIER3 registers from "struct kvmppc_host_state". Fixes: 57dc0eed ("KVM: PPC: Book3S HV P9: Implement PMU save/restore in C") Signed-off-by:
Kajol Jain <kjain@linux.ibm.com> Reviewed-by:
Athira Rajeev <atrajeev@linux.vnet.ibm.com> Signed-off-by:
-
