The macro 'HPRE_ADDR' is unnecessary, so expanding it.
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently, an invalid dma address may be unmapped when calling
'xx_data_clr_all' in error path, so check dma address of sqe in/out
if initialized before calling 'dma_free_coherent' or 'dma_unmap_single'.

Fixes: a9214b0b ("crypto: hisilicon - fix the check on dma address")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently,'cra_driver_name' cannot be used to specify ecdh algorithm
with a special curve, so extending it with curve name.

Fixes: 6763f5ea ("crypto: ecdh - move curve_id of ECDH from ...")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently, 'cra_driver_name' cannot be used to specify ecdh algorithm
with a special curve, so extending it with curve name.

Although using 'cra_name' can also specify a special curve, but ecdh
generic driver cannot be specified when vendor hardware accelerator
has registered.

Fixes: 6763f5ea ("crypto: ecdh - move curve_id of ECDH from ...")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Actual data length of the 'secret' is not equal to the 'secret_size'.

Since the 'curve_id' has removed in the 'secret', the 'secret_size'
should subtract the length of the 'curve_id'.

Fixes: 6763f5ea ("crypto: ecdh - move curve_id of ECDH from ...")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 8a63b199 ("crypto: ux500 - Add driver for HASH hardware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix function name in nitrox_reqmgr.c kernel-doc comment
to remove a warning.

drivers/crypto/cavium/nitrox/nitrox_reqmgr.c:382: warning: expecting
prototype for nitrox_se_request(). Prototype was for
nitrox_process_se_request() instead
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Pointer 'sg' is being initialized however this value is never
read as 'sg' is assigned a same value in for_each_sg().
Remove the redundant assignment.

Cleans up clang warning:

drivers/crypto/cavium/nitrox/nitrox_reqmgr.c:161:22: warning: Value
stored to 'sg' during its initialization is never read
[clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

No maintainer exists for ixp4xx_crypto, since I have access to a board
with it, I propose to maintain it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

drivers/crypto/ixp4xx_crypto.c is missing in the IXP4XX arch file list.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch fixes all alignment issues reported by checkpatch.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

fixes all single statement issues reported by checkpatch
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch fixes all checkpatch report about static init.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fixes all whitespace issues reported by checkpatch
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Convert all old printk to dev_xxx.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fixes all issues reported by checkpatch about "unsigned", lets convert
them to unsigned int.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Testing ixp4xx_crypto lead to:
alg: skcipher: ecb(des)-ixp4xx encryption overran dst buffer on test vector 0, cfg="two even aligned splits"

The HW overwrites destination always when sg_nents() > 1.
The problem seems that the HW always write areq->cryptlen bytes on the
last SG.
A comment in driver's code seems to give a clue that multiple SG was not
planned "This was never tested by Intel for more than one dst buffer, I think".
So let's add a fallback for this situation.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Crypto selftests fail on ixp4xx since it do not update IV after skcipher
requests.

Fixes: 81bef015 ("crypto: ixp4xx - Hardware crypto support for IXP4xx CPUs")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Testing ixp4xx_crypto with CONFIG_DMA_API_DEBUG lead to the following error:
DMA-API: platform ixp4xx_crypto.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=24 bytes]

This is due to dma_unmap using the wrong address.

Fixes: 0d44dc59 ("crypto: ixp4xx - Fix handling of chained sg buffers")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

pm_runtime_resume_and_get() wraps around pm_runtime_get_sync() and
decrements the runtime PM usage counter in case the latter function
fails and keeps the counter balanced.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Qualcomm crypto engine does not handle the following scenarios and
will issue an abort. In such cases, pass on the transformation to
a fallback algorithm.

- DES3 algorithms with all three keys same.
- AES192 algorithms.
- 0 length messages.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add register programming sequence for enabling AEAD
algorithms on the Qualcomm crypto engine.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove various redundant checks in qce_auth_cfg. Also allow qce_auth_cfg
to take auth_size as a parameter which is a required setting for ccm(aes)
algorithms
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Introduce support to enable following algorithms in Qualcomm Crypto Engine.

- authenc(hmac(sha1),cbc(des))
- authenc(hmac(sha1),cbc(des3_ede))
- authenc(hmac(sha256),cbc(des))
- authenc(hmac(sha256),cbc(des3_ede))
- authenc(hmac(sha256),cbc(aes))
- ccm(aes)
- rfc4309(ccm(aes))
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

rf4309 is the specification that uses aes ccm algorithms with IPsec
security packets. Add a submode to identify rfc4309 ccm(aes) algorithm
in the crypto driver.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Qualcomm crypto engine allows for IV registers and status register
to be concatenated to the output. This option is enabled by setting the
RESULTS_DUMP field in GOPROC  register. This is useful for most of the
algorithms to either retrieve status of operation or in case of
authentication algorithms to retrieve the mac. But for ccm
algorithms, the mac is part of the output stream and not retrieved
from the IV registers, thus needing a separate buffer to retrieve it.
Make enabling RESULTS_DUMP field optional so that algorithms can choose
whether or not to enable the option.
Note that in this patch, the enabled algorithms always choose
RESULTS_DUMP to be enabled. But later with the introduction of ccm
algorithms, this changes.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

MAC_FAILED gets set in the status register if authenthication fails
for ccm algorithms(during decryption). Add support to catch and flag
this error.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The variable err is being initialized with a value that is
never read and it is being updated later with a new value.  The
initialization is redundant and can be removed

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use 'hlist_for_each_entry' instead of hand writing it.
This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Annotate the firmware files CCP might need using MODULE_FIRMWARE().
This will get them included into an initrd when CCP is also included
there. Otherwise the CCP module will not find its firmware when loaded
before the root-fs is mounted.
This can cause problems when the pre-loaded SEV firmware is too old to
support current SEV and SEV-ES virtualization features.

Fixes: e9372060 ("crypto: ccp - Allow SEV firmware to be chosen based on Family and Model")
Cc: stable@vger.kernel.org # v4.20+
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Unify similar build rules.

sha256-core.S opts out it because it is generated from sha512-armv8.pl.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Generate *.S by Perl like arch/{mips,x86}/crypto/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Unify similar build rules.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Generate *.S by Perl like arch/{mips,x86}/crypto/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Commit b9d79e4c ("fbmem: Mark proc_fb_seq_ops as __maybe_unused")
places the '__maybe_unused' in an entirely incorrect location between
the "struct" keyword and the structure name.

It's a wonder that gcc accepts that silently, but clang quite reasonably
warns about it:

    drivers/video/fbdev/core/fbmem.c:736:21: warning: attribute declaration must precede definition [-Wignored-attributes]
    static const struct __maybe_unused seq_operations proc_fb_seq_ops = {
                        ^

Fix it.

Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull drm fixes from Dave Airlie:
 "Bit later than usual, I queued them all up on Friday then promptly
  forgot to write the pull request email. This is mainly amdgpu fixes,
  with some radeon/msm/fbdev and one i915 gvt fix thrown in.

  amdgpu:
   - MPO hang workaround
   - Fix for concurrent VM flushes on vega/navi
   - dcefclk is not adjustable on navi1x and newer
   - MST HPD debugfs fix
   - Suspend/resumes fixes
   - Register VGA clients late in case driver fails to load
   - Fix GEM leak in user framebuffer create
   - Add support for polaris12 with 32 bit memory interface
   - Fix duplicate cursor issue when using overlay
   - Fix corruption with tiled surfaces on VCN3
   - Add BO size and stride check to fix BO size verification

  radeon:
   - Fix off-by-one in power state parsing
   - Fix possible memory leak in power state parsing

  msm:
   - NULL ptr dereference fix

  fbdev:
   - procfs disabled warning fix

  i915:
   - gvt: Fix a possible division by zero in vgpu display rate
     calculation"

* tag 'drm-next-2021-05-10' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: Use device specific BO size & stride check.
  drm/amdgpu: Init GFX10_ADDR_CONFIG for VCN v3 in DPG mode.
  drm/amd/pm: initialize variable
  drm/radeon: Avoid power table parsing memory leaks
  drm/radeon: Fix off-by-one power_state index heap overwrite
  drm/amd/display: Fix two cursor duplication when using overlay
  drm/amdgpu: add new MC firmware for Polaris12 32bit ASIC
  fbmem: Mark proc_fb_seq_ops as __maybe_unused
  drm/msm/dpu: Delete bonkers code
  drm/i915/gvt: Prevent divided by zero when calculating refresh rate
  amdgpu: fix GEM obj leak in amdgpu_display_user_framebuffer_create
  drm/amdgpu: Register VGA clients after init can no longer fail
  drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown
  drm/amdgpu: fix r initial values
  drm/amd/display: fix wrong statement in mst hpd debugfs
  amdgpu/pm: set pp_dpm_dcefclk to readonly on NAVI10 and newer gpus
  amdgpu/pm: Prevent force of DCEFCLK on NAVI10 and SIENNA_CICHLID
  drm/amdgpu: fix concurrent VM flushes on Vega/Navi v2
  drm/amd/display: Reject non-zero src_y and src_x for video planes

Pull block fix from Jens Axboe:
 "Turns out the bio max size change still has issues, so let's get it
  reverted for 5.13-rc1. We'll shake out the issues there and defer it
  to 5.14 instead"

* tag 'block-5.13-2021-05-09' of git://git.kernel.dk/linux-block:
  Revert "bio: limit bio max size"

Pull cifs fixes from Steve French:
 "Three small SMB3 chmultichannel related changesets (also for stable)
  from the SMB3 test event this week.

  The other fixes are still in review/testing"

* tag '5.13-rc-smb3-part3' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: if max_channels set to more than one channel request multichannel
  smb3: do not attempt multichannel to server which does not support it
  smb3: when mounting with multichannel include it in requested capabilities