Merge tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.17, 2nd take" from Shawn Guo:

i.MX fixes for 3.17, 2nd take:
 - Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
   configuration missing
 - A couple small SolidRun board fixes/correction from Rabeeh
   and Russell

* tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: dts: imx53-qsrb: Fix suspend/resume
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes against v3.17-rc2" from Tony Lindgren:

Fixes for omaps, mostly to revert NAND back to using software ECC
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.

* tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default

Add some more locations that aren't catched by the general wildcard.
This includes the devicetree files, clock directory, rk3x i2c driver,
everything in a third layer under drivers like iio/adc/rockchip_saradc.c
and the i2s driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch is important for the MicroSOM implementation due to the
following details -

1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
   PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).

In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There were several issues (of varying degree of importance) pointed out
with this code late in the review cycle, yet the code was still merged.
Let's rip it out for now and look at resubmitting at a later time.

This reverts most of commit 4fbe66d9.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.

My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.

In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.

So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>

For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.
Tested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When an alias for a clock already exists the warning is printed. For
every module with a main_clk defined, a clk alias for fck is added.
There are some components that have the same main_clk defined, so this
is a really normal situation.

For example the am33xx edma device has 4 components using the same main
clock. So there are three warnings in the boot log for this already
existing clock alias:
	platform 49000000.edma: alias fck already exists
	platform 49000000.edma: alias fck already exists
	platform 49000000.edma: alias fck already exists

As this is only interesting for developers, this patch changes the
message to a debug message.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix %d confusingly prefixed with 0x in format string.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.

By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.

With this change, the following now works:

interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;

Fixes: 6e58b8f1 ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

commit 65b97cf6 introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.

Fix the issue by using the correct mask.

Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.

Fixes: 65b97cf6 (mtd: nand: omap2: handle nand on gpmc)

Cc: <stable@vger.kernel.org>	[3.7+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c5270 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf5 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d0391 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.

This defect can be observed on the following boards during legacy boot

-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull NFS client fixes from Trond Myklebust:
 "Highlights:

   - more fixes for read/write codepath regressions
     * sleeping while holding the inode lock
     * stricter enforcement of page contiguity when coalescing requests
     * fix up error handling in the page coalescing code

   - don't busy wait on SIGKILL in the file locking code"

* tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
  nfs: can_coalesce_requests must enforce contiguity
  nfs: disallow duplicate pages in pgio page vectors
  nfs: don't sleep with inode lock in lock_and_join_requests
  nfs: fix error handling in lock_and_join_requests
  nfs: use blocking page_group_lock in add_request
  nfs: fix nonblocking calls to nfs_page_group_lock
  nfs: change nfs_page_group_lock argument

Merge tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas

Pull SH driver fix from Simon Horman:
 "Confine SH_INTC to platforms that need it"

* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  sh: intc: Confine SH_INTC to platforms that need it

Pull MIPS fixes from Ralf Baechle:
 "Pretty much all across the field so with this we should be in
  reasonable shape for the upcoming -rc2"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: OCTEON: make get_system_type() thread-safe
  MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
  MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
  MIPS: EVA: Add new EVA header
  MIPS: scall64-o32: Fix indirect syscall detection
  MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
  MIPS: Loongson: Fix COP2 usage for preemptible kernel
  MIPS: NL: Fix nlm_xlp_defconfig build error
  MIPS: Remove race window in page fault handling
  MIPS: Malta: Improve system memory detection for '{e, }memsize' >= 2G
  MIPS: Alchemy: Fix db1200 PSC clock enablement
  MIPS: BCM47XX: Fix reboot problem on BCM4705/BCM4785
  MIPS: Remove duplicated include from numa.c
  MIPS: Add common plat_irq_dispatch declaration
  MIPS: MSP71xx: remove unused plat_irq_dispatch() argument
  MIPS: GIC: Remove useless parens from GICBIS().
  MIPS: perf: Mark pmu interupt IRQF_NO_THREAD

Merge tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull fix for ftrace function tracer/profiler conflict from Steven Rostedt:
 "The rewrite of the ftrace code that makes it possible to allow for
  separate trampolines had a design flaw with the interaction between
  the function and function_graph tracers.

  The main flaw was the simplification of the use of multiple tracers
  having the same filter (like function and function_graph, that use the
  set_ftrace_filter file to filter their code).  The design assumed that
  the two tracers could never run simultaneously as only one tracer can
  be used at a time.  The problem with this assumption was that the
  function profiler could be implemented on top of the function graph
  tracer, and the function profiler could run at the same time as the
  function tracer.  This caused the assumption to be broken and when
  ftrace detected this failed assumpiton it would spit out a nasty
  warning and shut itself down.

  Instead of using a single ftrace_ops that switches between the
  function and function_graph callbacks, the two tracers can again use
  their own ftrace_ops.  But instead of having a complex hierarchy of
  ftrace_ops, the filter fields are placed in its own structure and the
  ftrace_ops can carefully use the same filter.  This change took a bit
  to be able to allow for this and currently only the global_ops can
  share the same filter, but this new design can easily be modified to
  allow for any ftrace_ops to share its filter with another ftrace_ops.

  The first four patches deal with the change of allowing the ftrace_ops
  to share the filter (and this needs to go to 3.16 as well).

  The fifth patch fixes a bug that was also caused by the new changes
  but only for archs other than x86, and only if those archs implement a
  direct call to the function_graph tracer which they do not do yet but
  will in the future.  It does not need to go to stable, but needs to be
  fixed before the other archs update their code to allow direct calls
  to the function_graph trampoline"

* tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Use current addr when converting to nop in __ftrace_replace_code()
  ftrace: Fix function_profiler and function tracer together
  ftrace: Fix up trampoline accounting with looping on hash ops
  ftrace: Update all ftrace_ops for a ftrace_hash_ops update
  ftrace: Allow ftrace_ops to use the hashes from other ops

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Hummingboard has no over current hardware, so disable the over current
detection for both ports.

Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Pull x86 fixes from Ingo Molnar:
 "A couple of EFI fixes, plus misc fixes all around the map"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/arm64: Store Runtime Services revision
  firmware: Do not use WARN_ON(!spin_is_locked())
  x86_32, entry: Clean up sysenter_badsys declaration
  x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
  x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
  x86/mm: Fix RCU splat from new TLB tracepoints

Pull perf fixes from Ingo Molnar:
 "A kprobes and a perf compat ioctl fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Handle compat ioctl
  kprobes: Skip kretprobe hit in NMI context to avoid deadlock

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes from this week, it's been pretty quiet and
  nothing really stands out as particularly noteworthy here -- mostly
  minor fixes across the field:

   - ODROID booting was fixed due to PMIC interrupts missing in DT
   - a collection of i.MX fixes
   - minor Tegra fix for regulators
   - Rockchip fix and addition of SoC-specific mailing list to make it
     easier to find posted patches"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  bus: arm-ccn: Fix warning message
  ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
  ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings
  ARM: dts: ODROID i2c improvements
  ARM: dts: Enable PMIC interrupts on ODROID
  ARM: dts: imx6sx: fix the pad setting for uart CTS_B
  ARM: dts: i.MX53: fix apparent bug in VPU clks
  ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
  ARM: dts: imx6: edmqmx6: change enet reset pin
  ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
  ARM: imx: remove unnecessary ARCH_HAS_OPP select
  ARM: imx: fix TLB missing of IOMUXC base address during suspend
  ARM: imx6: fix SMP compilation again
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes

Pull gpio fixes from Linus Walleij:

 - a largeish fix for the IRQ handling in the new Zynq driver.  The
   quite verbose commit message gives the exact details.
 - move some defines for gpiod flags outside an ifdef to make stub
   functions work again.
 - various minor fixes that we can accept for -rc1.

* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio-lynxpoint: enable input sensing in resume
  gpio: move GPIOD flags outside #ifdef
  gpio: delete unneeded test before of_node_put
  gpio: zynq: Fix IRQ handlers
  gpiolib: devres: use correct structure type name in sizeof
  MAINTAINERS: Change maintainer for gpio-bcm-kona.c

Pull drm fixes from Dave Airlie:
 "Intel and radeon fixes.

  Post KS/LC git requests from i915 and radeon stacked up.  They are all
  fixes along with some new pci ids for radeon, and one maintainers file
  entry.

   - i915: display fixes and irq fixes
   - radeon: pci ids, and misc gpuvm, dpm and hdp cache"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
  MAINTAINERS: Add entry for Renesas DRM drivers
  drm/radeon: add additional SI pci ids
  drm/radeon: add new bonaire pci ids
  drm/radeon: add new KV pci id
  Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
  drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
  drm/radeon: fix active cu count for SI and CIK
  drm/radeon: re-enable selective GPUVM flushing
  drm/radeon: Sync ME and PFP after CP semaphore waits v4
  drm/radeon: fix display handling in radeon_gpu_reset
  drm/radeon: fix pm handling in radeon_gpu_reset
  drm/radeon: Only flush HDP cache for indirect buffers from userspace
  drm/radeon: properly document reloc priority mask
  drm/i915: don't try to retrain a DP link on an inactive CRTC
  drm/i915: make sure VDD is turned off during system suspend
  drm/i915: cancel hotplug and dig_port work during suspend and unload
  drm/i915: fix HPD IRQ reenable work cancelation
  drm/i915: take display port power domain in DP HPD handler
  drm/i915: Don't try to enable cursor from setplane when crtc is disabled
  drm/i915: Skip load detect when intel_crtc->new_enable==true
  ...

As reported by Dan Aloni, commit f8567a38 ("aio: fix aio request
leak when events are reaped by userspace") introduces a regression when
user code attempts to perform io_submit() with more events than are
available in the ring buffer.  Reverting that commit would reintroduce a
regression when user space event reaping is used.

Fixing this bug is a bit more involved than the previous attempts to fix
this regression.  Since we do not have a single point at which we can
count events as being reaped by user space and io_getevents(), we have
to track event completion by looking at the number of events left in the
event ring.  So long as there are as many events in the ring buffer as
there have been completion events generate, we cannot call
put_reqs_available().  The code to check for this is now placed in
refill_reqs_available().

A test program from Dan and modified by me for verifying this bug is available
at http://www.kvack.org/~bcrl/20140824-aio_bug.c .
Reported-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Dan Aloni <dan@kernelim.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: stable@vger.kernel.org      # v3.16 and anything that f8567a38 was backported to
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A message warning a user about wrong vc value was printing
out port instead.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>

Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.

(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)

Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:

Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.

* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>

This pull just contains some new pci ids.

* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: add additional SI pci ids
  drm/radeon: add new bonaire pci ids
  drm/radeon: add new KV pci id

Add the new list that Rockchip-specific patches should also be directed to.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.

This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Merge "Allwinner DT changes, take 2" from Maxime Ripard:

Only a single patch in here that fixes a DTC warning.

* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>

In __ftrace_replace_code(), when converting the call to a nop in a function
it needs to compare against the "curr" (current) value of the ftrace ops, and
not the "new" one. It currently does not affect x86 which is the only arch
to do the trampolines with function graph tracer, but when other archs that do
depend on this code implement the function graph trampoline, it can crash.

Here's an example when ARM uses the trampolines (in the future):

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 9 at kernel/trace/ftrace.c:1716 ftrace_bug+0x17c/0x1f4()
 Modules linked in: omap_rng rng_core ipv6
 CPU: 0 PID: 9 Comm: migration/0 Not tainted 3.16.0-test-10959-gf0094b28-dirty #52
 [<c02188f4>] (unwind_backtrace) from [<c021343c>] (show_stack+0x20/0x24)
 [<c021343c>] (show_stack) from [<c095a674>] (dump_stack+0x78/0x94)
 [<c095a674>] (dump_stack) from [<c02532a0>] (warn_slowpath_common+0x7c/0x9c)
 [<c02532a0>] (warn_slowpath_common) from [<c02532ec>] (warn_slowpath_null+0x2c/0x34)
 [<c02532ec>] (warn_slowpath_null) from [<c02cbac4>] (ftrace_bug+0x17c/0x1f4)
 [<c02cbac4>] (ftrace_bug) from [<c02cc44c>] (ftrace_replace_code+0x80/0x9c)
 [<c02cc44c>] (ftrace_replace_code) from [<c02cc658>] (ftrace_modify_all_code+0xb8/0x164)
 [<c02cc658>] (ftrace_modify_all_code) from [<c02cc718>] (__ftrace_modify_code+0x14/0x1c)
 [<c02cc718>] (__ftrace_modify_code) from [<c02c7244>] (multi_cpu_stop+0xf4/0x134)
 [<c02c7244>] (multi_cpu_stop) from [<c02c6e90>] (cpu_stopper_thread+0x54/0x130)
 [<c02c6e90>] (cpu_stopper_thread) from [<c0271cd4>] (smpboot_thread_fn+0x1ac/0x1bc)
 [<c0271cd4>] (smpboot_thread_fn) from [<c026ddf0>] (kthread+0xe0/0xfc)
 [<c026ddf0>] (kthread) from [<c020f318>] (ret_from_fork+0x14/0x20)
 ---[ end trace dc9ce72c5b617d8f ]---
[   65.047264] ftrace failed to modify [<c0208580>] asm_do_IRQ+0x10/0x1c
[   65.054070]  actual: 85:1b:00:eb

Fixes: 7413af1f "ftrace: Make get_ftrace_addr() and get_ftrace_addr_old() global"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

The latest rewrite of ftrace removed the separate ftrace_ops of
the function tracer and the function graph tracer and had them
share the same ftrace_ops. This simplified the accounting by removing
the multiple layers of functions called, where the global_ops func
would call a special list that would iterate over the other ops that
were registered within it (like function and function graph), which
itself was registered to the ftrace ops list of all functions
currently active. If that sounds confusing, the code that implemented
it was also confusing and its removal is a good thing.

The problem with this change was that it assumed that the function
and function graph tracer can never be used at the same time.
This is mostly true, but there is an exception. That is when the
function profiler uses the function graph tracer to profile.
The function profiler can be activated the same time as the function
tracer, and this breaks the assumption and the result is that ftrace
will crash (it detects the error and shuts itself down, it does not
cause a kernel oops).

To solve this issue, a previous change allowed the hash tables
for the functions traced by a ftrace_ops to be a pointer and let
multiple ftrace_ops share the same hash. This allows the function
and function_graph tracer to have separate ftrace_ops, but still
share the hash, which is what is done.

Now the function and function graph tracers have separate ftrace_ops
again, and the function tracer can be run while the function_profile
is active.

Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>