- 25 May, 2023 40 commits
-
-
Stephan Gerhold authored
For some reason DB410c has completely bogus regulator constraints that actually just correspond to the programmable voltages which are already provided by the regulator driver. Some of them are not just outside the recommended operating conditions of the APQ8016E SoC but even exceed the absolute maximum ratings, potentially risking permanent device damage. In practice it's not quite as dangerous thanks to the RPM firmware: It turns out that it has its own voltage constraints and silently clamps all regulator requests. For example, requesting 3.3V for L5 (allowed by the current regulator constraints!) still results in 1.8V being programmed in the actual regulator hardware. Experimentation with various voltages shows that the internal RPM voltage constraints roughly correspond to the safe "specified range" in the PM8916 Device Specification (rather than the "programmable range" used inside apq8016-sbc.dtsi right now). Combine those together with some fixed voltages used in the old msm-3.10 device tree from Qualcomm to give DB410c some actually valid voltage constraints. Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Fixes: 4c7d53d1 ("arm64: dts: apq8016-sbc: add regulators support") Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
-
Jianhua Lu authored
Remove a redundant empty line introduced by commit 51c4c2bd ("arm64: dts: qcom: sm8250-xiaomi-elish-boe: Add mdss and dsi panel") Signed-off-by:
Jianhua Lu <lujianhua000@gmail.com> Signed-off-by:
-
Kathiravan T authored
Add QUP(SPI / I2C) peripheral, PRNG, WDOG and the remaining UART nodes. While at it, enable the SPI NOR in RDP433 board. Signed-off-by:
Kathiravan T <quic_kathirav@quicinc.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Enable Display Subsystem with Visionox VTDR6130 Panel (same as on MTP8550). Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
MDP in sm8550.dtsi is not disabled (although its parent MDSS is), so board DTS does not have to enable it. Suggested-by:
-
Krzysztof Kozlowski authored
Enable the Display Clock Controller by default in SoC DTSI so unused clocks can be turned off. It does not require any external resources, so as core SoC component should be always available to boards. Suggested-by:
-
Krzysztof Kozlowski authored
Enable PM8550 PMIC flash LED controller and add two flash LEDs using four current outputs. Signed-off-by:
-
Krzysztof Kozlowski authored
Add node for PM8550 PMIC flash LED controller. Signed-off-by:
-
Luca Weiss authored
Somehow wifi was placed further up in the file than where it should be. Move it down so the nodes are sorted by reg again. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Reviewed-by:
-
Konrad Dybcio authored
We need more granularity for things like the GPU. Add the missing levels. This unfortunately requires some re-indexing, resulting in an ugly diff. Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Nikita Travkin authored
Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform. The laptop design is similar to trogdor in the choice of primary components but the specifics on usage of those differ slightly. Add the devicetree for the laptop with support for most of the hardware present. Signed-off-by:
Nikita Travkin <nikita@trvn.ru> Reviewed-by:
-
Nikita Travkin authored
Acer Aspire 1 is a laptop based on sc7180. Document it's compatible. Signed-off-by:
-
Nikita Travkin authored
mdss is useless without a display controller which makes explicitly enabling mdp redundant. Have it enabled by default to drop the extra node for all users. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Nikita Travkin authored
lpass clocks are usually blocked from HLOS by the firmware and instead are managed by the ADSP. Mark them as reserved and explicitly enable in the CrOS boards that have special, cooperative firmware. The IDP board gets lpass clocks disabled as it doesn't make use of sound anyway and might use Qualcomm firmware that blocks those clocks. [1] [1] https://lore.kernel.org/all/ZBJhmDd3zK%2FAiwBD@google.com/Signed-off-by:
-
Krzysztof Kozlowski authored
Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX and TX. Signed-off-by:
-
Krzysztof Kozlowski authored
Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX and TX. Signed-off-by:
-
Yang Xiwen authored
It's possible to use this device with a (non-standard) hub to get USB working in host mode, but dr_mode="peripheral" prevents the UDC to do so. Remove dr_mode="peripheral" and add usb-role-switch so that it defaults to otg mode and can be switched to host mode in userspace. Signed-off-by:
Yang Xiwen <forbidden405@outlook.com> Signed-off-by:
-
Luca Weiss authored
MSM8953 has two DMA controllers for the various I2C, SPI and UART busses. Add the nodes and configure all the I2C nodes so that the driver can use the DMA. Reviewed-by:
Luca Weiss <luca@z3ntu.xyz> Signed-off-by:
-
Luca Weiss authored
Add a node for the GPIOs found on the pm8953. Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
"soc" node is supposed to have unit address: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name Signed-off-by:
-
Krzysztof Kozlowski authored
Add missing reg property to touchscreen child node to fix dtbs W=1 warnings: Warning (unit_address_vs_reg): /soc@0/geniqup@ac0000/i2c@a98000/touchscreen@20/rmi4-f12@12: node has a unit name, but no reg or ranges property Fixes: be497abe ("arm64: dts: qcom: Add support for Xiaomi Mi Mix2s") Signed-off-by:
Molly Sophia <mollysophia379@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/pinctrl@f000000: simple-bus unit address format error, expected "f100000" Fixes: ffc50b2d ("arm64: dts: qcom: Add base SM8550 dtsi") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/crypto@1de0000: simple-bus unit address format error, expected "1dfa000" Fixes: 433477c3 ("arm64: dts: qcom: sm8550: add QCrypto nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/phy@88e9000: simple-bus unit address format error, expected "88e8000" Fixes: 2458a305 ("arm64: dts: qcom: sm8350: switch to combo usb3/dp phy") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/phy@1c0f000: simple-bus unit address format error, expected "1c0e000" Fixes: 6daee406 ("arm64: dts: qcom: sm8350: add PCIe devices") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/dma-controller@900000: simple-bus unit address format error, expected "9800000" Fixes: bc08fbf4 ("arm64: dts: qcom: sm8350: Define GPI DMA engines") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/thermal-sensor@4410000: simple-bus unit address format error, expected "4411000" Fixes: 7b74cba6 ("arm64: dts: qcom: sm6115: Add TSENS node") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/camss@a00000: simple-bus unit address format error, expected "acb3000" Fixes: d48a6698 ("arm64: dts: qcom: sdm845: Add CAMSS ISP node") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/camss@ca00000: simple-bus unit address format error, expected "ca00020" Fixes: f3d5d3cc ("arm64: dts: qcom: sdm630: Configure the camera subsystem") Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/camss@a00000: simple-bus unit address format error, expected "a34000" Fixes: e0531312 ("arm64: dts: qcom: msm8996: Add CAMSS support") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/spmi@fc4c0000: simple-bus unit address format error, expected "fc4cf000" Fixes: b0ad598f ("arm64: dts: qcom: msm8994: Add SPMI PMIC arbiter device") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/mmc@7824000: simple-bus unit address format error, expected "7824900" Warning (simple_bus_reg): /soc@0/mmc@7864000: simple-bus unit address format error, expected "7864900" Warning (simple_bus_reg): /soc@0/mmc@7a24000: simple-bus unit address format error, expected "7a24900" Fixes: 0484d3ce ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs") Signed-off-by:
Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/remoteproc@a21b000: simple-bus unit address format error, expected "a204000" Fixes: b1242864 ("arm64: dts: MSM8953: Add wcnss nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/iommu@1e00000: simple-bus unit address format error, expected "1e20000" Fixes: c0b9575a ("arm64: dts: qcom: msm8953: add APPS IOMMU") Signed-off-by:
-
