Change the name of controller to a more meaningful one.
Signed-off-by: Marcos Alano <marcoshalano@gmail.com>
Link: https://lore.kernel.org/r/20220212191014.1754721-1-marcoshalano@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The PS/2 bus defines the data and clock line be open drain, therefore
for both enforce the particular GPIO flags in the driver.

Without enforcing to flag at least the clock gpio as open drain we run
into the following warning:

WARNING: CPU: 1 PID: 40 at drivers/gpio/gpiolib.c:3175 gpiochip_enable_irq+0x54/0x90

gpiochip_enable_irq() warns on a GPIO being configured as output while
serving as IRQ source without being flagged as open drain.
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Link: https://lore.kernel.org/r/20220215180829.63543-4-danilokrummrich@dk-develop.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sending the data before processing the stop bit from the device already
saves the data of the current xfer in case the stop bit is missed.

However, when TX xfers are enabled this introduces a race condition when
a peripheral driver using the bus immediately requests a TX xfer from IRQ
context.

Therefore the data must be send after receiving the stop bit, although
it is possible the data is lost when missing the stop bit.
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Link: https://lore.kernel.org/r/20220215160208.34826-5-danilokrummrich@dk-develop.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Actually, there's no extra clock pulse to wait for.

The assumption of an extra clock pulse was mistakenly derived from the
fact that by the time this driver was introduced the GPIO controller of
the test machine (bcm2835) generated spurious interrupts.

Since now spurious interrupts are handled properly this can and must be
removed in order to make TX xfers work properly.

While at it, remove duplicate gpiod_direction_input(). The data gpio
must already be configured to act as input when receiving the ACK bit.

This patch is tested with the original hardware (peripherals and board)
the driver was developed on.
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Link: https://lore.kernel.org/r/20220215160208.34826-4-danilokrummrich@dk-develop.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Using jiffies for the IRQ timekeeping is not sufficient for two reasons:

(1) Usually jiffies have a resolution of 1ms to 10ms. The IRQ intervals
    based on the clock frequency of PS2 protocol specification (10kHz -
    16.7kHz) are between ~60us and 100us only. Therefore only those IRQ
    intervals can be detected which are either at the end of a transfer
    or are overly delayed. While this is sufficient in most cases, since
    we have quite a lot of ways to detect faulty transfers, it can
    produce false positives in rare cases: When the jiffies value
    changes right between two interrupt that are in time, we wrongly
    assume that we missed one or more clock cycles.

(2) Some gpio controllers (e.g. the one in the bcm283x chips) may generate
    spurious IRQs when processing interrupts in the frequency given by PS2
    devices.

Both issues can be fixed by using ktime resolution for IRQ timekeeping.

However, it is still possible to miss clock cycles without detecting
them. When the PS2 device generates the falling edge of the clock signal
we have between ~30us and 50us to sample the data line, because after
this time we reach the next rising edge at which the device changes the
data signal already. But, the only thing we can detect is whether the
IRQ interval is within the given period. Therefore it is possible to
have an IRQ latency greater than ~30us to 50us, sample the wrong bit on
the data line and still be on time with the next IRQ. However, this can
only happen when within a given transfer the IRQ latency increases
slowly.

___            ______            ______            ______            ___
   \          /      \          /      \          /      \          /
    \        /        \        /        \        /        \        /
     \______/          \______/          \______/          \______/

    |-----------------|                 |--------|
         60us/100us                      30us/50us
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Link: https://lore.kernel.org/r/20220215160208.34826-3-danilokrummrich@dk-develop.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Refactor struct ps2_gpio_data in order to clearly separate RX and TX
state data.

This change intends to increase code readability and does not bring any
functional change.
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Link: https://lore.kernel.org/r/20220215160208.34826-2-danilokrummrich@dk-develop.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

MT6358 pmic keys behave differently than mt6397 and mt6323: there are
two interrupts per key: one for press, the other one for release (_r)
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220121140323.4080640-4-mkorpershoek@baylibre.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add the binding documentation of the mtk-pmic-keys for the MT6358 PMICs.

MT6358 is a little different since it used separate IRQs for the
release key (_r) event
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220121140323.4080640-3-mkorpershoek@baylibre.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some pmics of the mt6397 family (such as MT6358), have two IRQs per
physical key: one for press event, another for release event.

The mtk-pmic-keys driver assumes that each key only has one
IRQ. The key index and the RES_IRQ resource index have a 1/1 mapping.

This won't work for MT6358, as we have multiple resources (2) for one key.

To prepare mtk-pmic-keys to support MT6358, retrieve IRQs by name
instead of by index.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220121140323.4080640-2-mkorpershoek@baylibre.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with mainline to bring in the latest API changes.

change 'postion' to 'position'
Signed-off-by: Qinghua Jin <qhjin.dev@gmail.com>
Link: https://lore.kernel.org/r/20220106084215.355295-1-qhjin.dev@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull input fix from Dmitry Torokhov:
 "A small fixup to the Zinitix touchscreen driver to avoid enabling the
  IRQ line before we successfully requested it"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: zinitix - make sure the IRQ is allocated before it gets enabled

Pull ARM SoC fix from Olof Johansson:
 "One more fix for 5.16

  I had missed one patch when I sent up what I thought was the last
  batch of fixes for this release. This one fixes issues on the
  Raspberry Pi platforms due to gpio init changes this release, so
  hopefully we can get it merged before final release is cut"

* tag 'soc-fixes-5.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: gpio-ranges property is now required

Merge tag 'perf-tools-fixes-for-v5.16-2022-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Revert "libtraceevent: Increase libtraceevent logging when verbose",
   breaks the build with libtraceevent-1.3.0, i.e. when building with
   'LIBTRACEEVENT_DYNAMIC=1'.

 - Avoid early exit in 'perf trace' due to running SIGCHLD handler
   before it makes sense to. It can happen when using a BPF source code
   event that have to be first built into an object file.

* tag 'perf-tools-fixes-for-v5.16-2022-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  Revert "libtraceevent: Increase libtraceevent logging when verbose"
  perf trace: Avoid early exit due to running SIGCHLD handler before it makes sense to

This reverts commit f7d6779d.

This bisected regression has impacted suspend-resume stability
since 5.15-rc1. It regressed -stable via 5.14.10.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215315
Fixes: f7d6779d ("drm/amdgpu: stop scheduler when calling hw_fini (v2)")
Cc: Guchun Chen <guchun.chen@amd.com>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Zinitix BT532 is another touch controller that seem to implement the
same interface as an already supported BT541. Add it to the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.

To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.

We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.

Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This converts the Zinitix BT4xx and BT5xx touchscreen bindings to YAML,
fix them up a bit and extends them.

We list all the existing BT4xx and BT5xx components with compatible
strings.  These are all similar, use the same bindings and work in
similar ways.

We rename the supplies from the erroneous vdd/vddo to the actual supply
names vcca/vdd as specified on the actual component. It is long
established that supplies shall be named after the supply pin names of a
component.  The confusion probably stems from that in a certain product
the rails to the component were named vdd/vddo. Drop some notes on how OS
implementations should avoid confusion by first looking for vddo, and if
that exists assume the legacy binding pair and otherwise use vcca/vdd.

Add reset-gpios as sometimes manufacturers pulls a GPIO line to the reset
line on the chip.

Add optional touchscreen-fuzz-x and touchscreen-fuzz-y properties.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Fixed dt_schema_check]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-3-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.

Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The power button on Cherry Trail systems with an AXP288 PMIC is connected
to both the power button pin of the PMIC as well as to a power button GPIO
on the Cherry Trail SoC itself. This leads to double power button event
reporting which is a problem.

Since reporting power button presses through the PMIC is not supported on
all PMICs used on Cherry Trail systems, we want to keep the GPIO
power button events, so the axp20x-pek code checks for the presence of
a GPIO power button and in that case does not register its input-device.

On most systems the GPIO power button also can wake-up the system from
suspend, so the axp20x-pek driver would also not register its interrupt
handler. But on some systems there was a bug causing wakeup by the GPIO
power button handler to not work.

Commit 9747070c ("Input: axp20x-pek - always register interrupt
handlers") was added as a work around for this registering the axp20x-pek
interrupts, but not the input-device on Cherry Trail systems.

In the mean time the root-cause of the GPIO power button wakeup events
not working has been found and fixed by the "pinctrl: cherryview: Do not
allow the same interrupt line to be used by 2 pins" patch,
so this is no longer necessary.

This reverts the workaround going back to only registering the
interrupt handlers on systems where we also register the input-device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20220106111647.66520-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since [1], added in 5.7, the absence of a gpio-ranges property has
prevented GPIOs from being restored to inputs when released.
Add those properties for BCM283x and BCM2711 devices.

[1] commit 2ab73c6d ("gpio: Support GPIO controllers without
    pin-ranges")

Link: https://lore.kernel.org/r/20220104170247.956760-1-linus.walleij@linaro.org
Fixes: 2ab73c6d ("gpio: Support GPIO controllers without pin-ranges")
Fixes: 266423e6 ("pinctrl: bcm2835: Change init order for gpio hogs")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211206092237.4105895-3-phil@raspberrypi.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ARM SoC fixes from Olof Johansson:
 "A few more fixes have come in, nothing overly severe but would be good
  to get in by final release:

   - More specific compatible fields on the qspi controller for socfpga,
     to enable quirks in the driver

   - A runtime PM fix for Renesas to fix mismatched reference counts on
     errors"

* tag 'soc-fixes-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: socfpga: change qspi to "intel,socfpga-qspi"
  dt-bindings: spi: cadence-quadspi: document "intel,socfpga-qspi"
  reset: renesas: Fix Runtime PM usage

Pull i2c fixes from Wolfram Sang:
 "Fix the regression with AMD GPU suspend by reverting the
  handling of bus regulators in the I2C core.

  Also, there is a fix for the MPC driver to prevent an
  out-of-bound-access"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: core: support bus regulator controlling in adapter"
  i2c: mpc: Avoid out of bounds memory access

Pull power supply fixes from Sebastian Reichel:
 "Three fixes for the 5.16 cycle:

   - Avoid going beyond last capacity in the power-supply core

   - Replace 1E6L with NSEC_PER_MSEC to avoid floating point calculation
     in LLVM resulting in a build failure

   - Fix ADC measurements in bq25890 charger driver"

* tag 'for-v5.16-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: reset: ltc2952: Fix use of floating point literals
  power: bq25890: Enable continuous conversion for ADC at charging
  power: supply: core: Break capacity loop

Pull xfs fix from Darrick Wong:

 - Make the old ALLOCSP ioctl behave in a consistent manner with newer
   syscalls like fallocate.

* tag 'xfs-5.16-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: map unwritten blocks in XFS_IOC_{ALLOC,FREE}SP just like fallocate

Pull cgroup fixes from Tejun Heo:
 "This contains the cgroup.procs permission check fixes so that they use
  the credentials at the time of open rather than write, which also
  fixes the cgroup namespace lifetime bug"

* 'for-5.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  selftests: cgroup: Test open-time cgroup namespace usage for migration checks
  selftests: cgroup: Test open-time credential usage for migration checks
  selftests: cgroup: Make cg_create() use 0755 for permission instead of 0644
  cgroup: Use open-time cgroup namespace for process migration perm checks
  cgroup: Allocate cgroup_file_ctx for kernfs_open_file->priv
  cgroup: Use open-time credentials for process migraton perm checks

Pull block fix from Jens Axboe:
 "Just the md bitmap regression this time"

* tag 'block-5.16-2022-01-07' of git://git.kernel.dk/linux-block:
  md/raid1: fix missing bitmap update w/o WriteMostly devices

Pull EDAC fix from Tony Luck:
 "Fix 10nm EDAC driver to release and unmap resources on systems without
  HBM"

* tag 'edac_urgent_for_v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/i10nm: Release mdev/mbase when failing to detect HBM

This largely reverts commit 5a7b95fb. It
breaks suspend with AMD GPUs, and we couldn't incrementally fix it. So,
let's remove the code and go back to the drawing board. We keep the
header extension to not break drivers already populating the regulator.
We expect to re-add the code handling it soon.

Fixes: 5a7b95fb ("i2c: core: support bus regulator controlling in adapter")
Reported-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Link: https://lore.kernel.org/r/1295184560.182511.1639075777725@mail.yahoo.comReported-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Link: https://lore.kernel.org/r/7143a7147978f4104171072d9f5225d2ce355ec1.camel@yandex.ru
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1850Tested-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # 5.14+

This reverts commit 08efcb4a.

This breaks the build as it will prefer using libbpf-devel header files,
even when not using LIBBPF_DYNAMIC=1, breaking the build.

This was detected on OpenSuSE Tumbleweed with libtraceevent-devel 1.3.0,
as described by Jiri Slaby:

=======================================================================
It breaks build with LIBTRACEEVENT_DYNAMIC and version 1.3.0:
> util/debug.c: In function ‘perf_debug_option’:
> util/debug.c:243:17: error: implicit declaration of function
‘tep_set_loglevel’ [-Werror=implicit-function-declaration]
>   243 |                 tep_set_loglevel(TEP_LOG_INFO);
>       |                 ^~~~~~~~~~~~~~~~
> util/debug.c:243:34: error: ‘TEP_LOG_INFO’ undeclared (first use in this
function); did you mean ‘TEP_PRINT_INFO’?
>   243 |                 tep_set_loglevel(TEP_LOG_INFO);
>       |                                  ^~~~~~~~~~~~
>       |                                  TEP_PRINT_INFO
> util/debug.c:243:34: note: each undeclared identifier is reported only once
for each function it appears in
> util/debug.c:245:34: error: ‘TEP_LOG_DEBUG’ undeclared (first use in this
function)
>   245 |                 tep_set_loglevel(TEP_LOG_DEBUG);
>       |                                  ^~~~~~~~~~~~~
> util/debug.c:247:34: error: ‘TEP_LOG_ALL’ undeclared (first use in this
function)
>   247 |                 tep_set_loglevel(TEP_LOG_ALL);
>       |                                  ^~~~~~~~~~~

It is because the gcc's command line looks like:
gcc
...
-I/home/abuild/rpmbuild/BUILD/tools/lib/
...
-DLIBTRACEEVENT_VERSION=65790
...
=======================================================================

The proper way to fix this is more involved and so not suitable for this
late in the 5.16-rc stage.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/lkml/bc2b0786-8965-1bcd-2316-9d9bb37b9c31@kernel.org
Cc: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: https://lore.kernel.org/lkml/YddGjjmlMZzxUZbN@kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

When running 'perf trace' with an BPF object like:

  # perf trace -e openat,tools/perf/examples/bpf/hello.c

the event parsing eventually calls llvm__get_kbuild_opts() that runs a
script and that ends up with SIGCHLD delivered to the 'perf trace'
handler, which assumes the workload process is done and quits 'perf
trace'.

Move the SIGCHLD handler setup directly to trace__run(), where the event
is parsed and the object is already compiled.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Christy Lee <christyc.y.lee@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220106222030.227499-1-jolsa@kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull kvm fixes from Paolo Bonzini:
 "Two small fixes for x86:

   - lockdep WARN due to missing lock nesting annotation

   - NULL pointer dereference when accessing debugfs"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Check for rmaps allocation
  KVM: SEV: Mark nested locking of kvm->lock

Pull drm fixes from Dave Airlie:
 "There is only the amdgpu runtime pm regression fix in here:

  amdgpu:

   - suspend/resume fix

   - fix runtime PM regression"

* tag 'drm-fixes-2022-01-07' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: disable runpm if we are the primary adapter
  fbdev: fbmem: add a helper to determine if an aperture is used by a fw fb
  drm/amd/pm: keep the BACO feature enabled for suspend

With TDP MMU being the default now, access to mmu_rmaps_stat debugfs
file causes following oops:

BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 PID: 3185 Comm: cat Not tainted 5.16.0-rc4+ #204
RIP: 0010:pte_list_count+0x6/0x40
 Call Trace:
  <TASK>
  ? kvm_mmu_rmaps_stat_show+0x15e/0x320
  seq_read_iter+0x126/0x4b0
  ? aa_file_perm+0x124/0x490
  seq_read+0xf5/0x140
  full_proxy_read+0x5c/0x80
  vfs_read+0x9f/0x1a0
  ksys_read+0x67/0xe0
  __x64_sys_read+0x19/0x20
  do_syscall_64+0x3b/0xc0
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7fca6fc13912

Return early when rmaps are not present.
Reported-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220105040337.4234-1-nikunj@amd.com>
Cc: stable@vger.kernel.org
Fixes: 3bcd0662 ("KVM: X86: Introduce mmu_rmaps_stat per-vm debugfs file")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Both source and dest vms' kvm->locks are held in sev_lock_two_vms.
Mark one with a different subtype to avoid false positives from lockdep.

Fixes: c9d61dcb (KVM: SEV: accept signals in sev_lock_two_vms)
Reported-by: Yiru Xu <xyru1999@gmail.com>
Tested-by: Jinrong Liang <cloudliang@tencent.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1641364863-26331-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull rdma fixes from Jason Gunthorpe:
 "Last pull for 5.16, the reversion has been known for a while now but
  didn't get a proper fix in time. Looks like we will have several
  info-leak bugs to take care of going foward.

   - Revert the patch fixing the DM related crash causing a widespread
     regression for kernel ULPs. A proper fix just didn't appear this
     cycle due to the holidays

   - Missing NULL check on alloc in uverbs

   - Double free in rxe error paths

   - Fix a new kernel-infoleak report when forming ah_attr's without
     GRH's in ucma"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/core: Don't infoleak GRH fields
  RDMA/uverbs: Check for null return of kmalloc_array
  Revert "RDMA/mlx5: Fix releasing unallocated memory in dereg MR flow"
  RDMA/rxe: Prevent double freeing rxe_map_set()

Pull tracing fixes from Steven Rostedt:
 "Three minor tracing fixes:

   - Fix missing prototypes in sample module for direct functions

   - Fix check of valid buffer in get_trace_buf()

   - Fix annotations of percpu pointers"

* tag 'trace-v5.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Tag trace_percpu_buffer as a percpu pointer
  tracing: Fix check for trace_percpu_buffer validity in get_trace_buf()
  ftrace/samples: Add missing prototypes direct functions

When a task is writing to an fd opened by a different task, the perm check
should use the cgroup namespace of the latter task. Add a test for it.
Tested-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

When a task is writing to an fd opened by a different task, the perm check
should use the credentials of the latter task. Add a test for it.
Tested-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>