- 03 Jun, 2019 1 commit
-
-
Daniel Vetter authored
With Eric's patch commit ba6e798e Author: Eric Anholt <eric@anholt.net> Date: Wed Apr 24 11:56:17 2019 -0700 drm/doc: Document expectation that userspace review looks at kernel uAPI. there's been concerns raised that we expect userspace people to do in-depth kernel patch review. That's not reasonable, same way kernel people can't review all the userspace we have. Try to clarify expectations a bit more. Cc: Eric Anholt <eric@anholt.net> Cc: Pekka Paalanen <ppaalanen@gmail.com> Cc: contact@emersion.fr Cc: wayland-devel@lists.freedesktop.org Acked-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
Simon Ser <contact@emersion.fr> Reviewed-by:
Pekka Paalanen <pekka.paalanen@collabora.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190521084849.27452-1-daniel.vetter@ffwll.ch
-
- 31 May, 2019 30 commits
-
-
Jyri Sarha authored
Implement HDMI audio support by using ASoC HDMI codec. The commit implements the necessary callbacks and configuration for the HDMI codec and registers a virtual platform device for the codec to attach. Signed-off-by:
Jyri Sarha <jsarha@ti.com> Reviewed-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
-
Jyri Sarha authored
The sii902x chip family supports also HDMI audio. Add binding for describing the necessary i2s and mclk wiring for it. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Jyri Sarha authored
Remove trailing white space from sii902x display bridge binding. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
-
Jyri Sarha authored
The pixel clock unit in the first two registers (0x00 and 0x01) of sii9022 is 10kHz, not 1kHz as in struct drm_display_mode. Division by 10 fixes the issue. Signed-off-by:
-
Jyri Sarha authored
Set output mode to HDMI or DVI according to EDID HDMI signature. Signed-off-by:
-
Tomi Valkeinen authored
The driver always sets InputBusFmt:EDGE to 0 (falling edge). Add drm_bridge_timings's input_bus_flags to reflect that the bridge samples on falling edges. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Tomi Valkeinen authored
Add DT property for defining the pin used for HPD. Signed-off-by:
-
Tomi Valkeinen authored
Add support for interrupt and hotplug handling. Both are optional. Signed-off-by:
-
Tomi Valkeinen authored
Add GPIO and interrupt related registers for HPD work. Mark INTSTS_G and GPIOI as volatile. Signed-off-by:
-
Tomi Valkeinen authored
We need to know the link bandwidth to filter out modes we cannot support, so we need to have read the display props before doing the filtering. To ensure we have up to date display props, call tc_get_display_props() in the beginning of tc_connector_get_modes(). Signed-off-by:
-
Tomi Valkeinen authored
In tc_bridge_mode_set callback, we store the pointer to the given drm_display_mode, and use the mode later. Storing a pointer in such a way looks very suspicious to me, and I have observed odd issues where the timings were apparently (at least mostly) zero. Do a copy of the drm_display_mode instead to ensure we don't refer to freed/modified data. Signed-off-by:
-
Tomi Valkeinen authored
drm_connector_helper_funcs.best_encoder is only needed when the connector can have more than one encoder, and that is never the case here. So remove tc_connector_best_encoder. Signed-off-by:
-
Tomi Valkeinen authored
We have tc_connector_mode_valid() to filter out videomdoes that the tc358767 cannot support. As it is a bridge limitation, change the code to use drm_bridge_funcs's mode_valid instead. Signed-off-by:
-
Tomi Valkeinen authored
tc_main_link_enable() checks if videomode has been set, and fails if there's no videomode. As tc_main_link_enable() no longer depends on the videomode, we can drop the check. Also, while tc_stream_enable() does depend on the videomode, we can expect that a mode has been set before drm_bridge_funcs.enable is called, so we don't need the check there either. Signed-off-by:
-
Tomi Valkeinen authored
The current link training code does unnecessary retry-loops, and does extra writes to the registers. It is easier to follow the flow and ensure it's similar to Toshiba's documentation if we deal with LT inside tc_main_link_enable() function. This patch adds tc_wait_link_training() which handles waiting for the LT phase to finish, and does the necessary LT register setups in tc_main_link_enable, without extra loops. Signed-off-by:
-
Tomi Valkeinen authored
The driver has a loop after ending link training, where it reads the DPCD link status and prints an error if that status is not ok. The loop is unnecessary, as far as I can understand from DP specs, so let's remove it. We can also print the more specific errors to help debugging. Signed-off-by:
-
Tomi Valkeinen authored
At the end of the link training, two steps have to be taken: 1) tc358767's LT mode is disabled by a write to DP0_SRCCTRL, and 2) Remove LT flag in DPCD 0x102. Toshiba's documentation tells to first write the DPCD, then modify DP0_SRCCTRL. In my testing this often causes issues, and the link disconnects right after those steps. If I reverse the steps, it works every time. There's a chance that this is DP sink specific, though, but as my testing shows this sequence to be much more reliable, let's change it. Signed-off-by:
-
Tomi Valkeinen authored
For some reason the driver has a msleep(100) after writing to DP_PHY_CTRL. Toshiba's documentation doesn't suggest any delay is needed, and I have not seen any issues with the sleep removed. Drop it, as msleep(100) is a rather big one. Signed-off-by:
Andrey Gusakov <andrey.gusakov@cogentembedded.com> Signed-off-by:
-
Tomi Valkeinen authored
Link training will sometimes fail if the DP link is enabled when tc_main_link_enable() is called. The driver makes sure the DP link is disabled when the DP output is disabled, and we never enable the DP without first disabling it, so this should never happen. However, as the HW behavior seems to be somewhat random if DP link has erroneously been left enabled, let's add a WARN_ON() for the case and set DP0CTL to 0. Signed-off-by:
-
Tomi Valkeinen authored
Currently the code writes 0 to DP0CTL in tc_stream_disable(), which disables the whole DP link instead of just the video stream. We always disable the link and the stream together from tc_bridge_disable(), so this doesn't cause any issues. Nevertheless, fix this by only clearing VID_EN in tc_stream_disable to stop the video stream while keeping the link enabled. Signed-off-by:
-
Tomi Valkeinen authored
Currently we have tc_main_link_setup(), which configures and enabled the link, but we have no counter-part for disabling the link. Add tc_main_link_disable, and rename tc_main_link_setup to tc_main_link_enable. Signed-off-by:
-
Tomi Valkeinen authored
We set up the PXL PLL inside tc_main_link_setup. This is unnecessary, and makes tc_main_link_setup depend on the video-mode, which should not be the case. As PXL PLL is used only for the video stream (and only when using the HW test pattern), let's move the PXL PLL setup into tc_stream_enable. Also, currently the PXL PLL is only disabled if the driver if removed. Let's disable the PXL PLL when the stream is disabled. Signed-off-by:
-
Tomi Valkeinen authored
It is nicer to have enable/disable functions instead of set(bool enable) style function. Split tc_main_link_stream into tc_stream_enable and tc_stream_disable. Signed-off-by:
-
Tomi Valkeinen authored
The driver currently sets the video stream registers in tc_main_link_setup. One should be able to establish the DP link without any video stream, so a more logical place is to configure the stream in the tc_main_link_stream. So move them there. Signed-off-by:
-
Tomi Valkeinen authored
The driver sets up AUX link at probe time, but, for some reason, also sets the main link's number of lanes using tc->link.base.num_lanes. This is not needed nor correct, as the number of lanes has not been decided yet. The number of lanes will be set later during main link setup. Modify aux_link_setup so that it does not use tc->link, and thus makes aux setup independent of the link probing. Signed-off-by:
-
Tomi Valkeinen authored
swing and preemp fields are not used. Remove them. Signed-off-by:
-
Tomi Valkeinen authored
Minor cleanups: - Use bool for boolean fields - Use DP_MAX_DOWNSPREAD_0_5 instead of BIT(0) - debug print down-spread and scrambler status Signed-off-by:
-
Tomi Valkeinen authored
DP always uses ANSI 8B10B encoding. Some monitors (old?) may not have the ANSI 8B10B bit set in DPCD, even if it should always be set. The tc358767 driver currently respects that flag, and turns the encoding off if the monitor does not have the bit set, which then results in the monitor not working. This patch makes the driver to always use ANSI 8B10B encoding, and drops the 'coding8b10b' field which is no longer used. Signed-off-by:
-
Tomi Valkeinen authored
We need to reset DPCD voltage-swing & pre-emphasis before starting the link training, as otherwise tc358767 will use the previous values as minimums. Signed-off-by:
-
Tomi Valkeinen authored
tc_aux_get_status() does not report AUX_TIMEOUT correctly, as it only checks the AUX_TIMEOUT if aux is still busy. Fix this by always checking for AUX_TIMEOUT. Signed-off-by:
-
- 30 May, 2019 1 commit
-
-
Maxime Ripard authored
The Allwinner SoCs have a MIPI-DSI and MIPI-D-PHY controllers supported in Linux, with a matching Device Tree binding. Now that we have the DT validation in place, let's convert the device tree bindings for that controller over to a YAML schemas. Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by:
Chen-Yu Tsai <wens@csie.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190527120910.18964-1-maxime.ripard@bootlin.com
-
- 29 May, 2019 2 commits
-
-
Imre Deak authored
Fix the breakage resulting in the stacktrace below, due to tx queue being full when trying to send an up-reply. txmsg->seqno is -1 in this case leading to a corruption of the mstb object by txmsg->dst->tx_slots[txmsg->seqno] = NULL; in process_single_up_tx_qlock(). [ +0,005162] [drm:process_single_tx_qlock [drm_kms_helper]] set_hdr_from_dst_qlock: failed to find slot [ +0,000015] [drm:drm_dp_send_up_ack_reply.constprop.19 [drm_kms_helper]] failed to send msg in q -11 [ +0,000939] BUG: kernel NULL pointer dereference, address: 00000000000005a0 [ +0,006982] #PF: supervisor write access in kernel mode [ +0,005223] #PF: error_code(0x0002) - not-present page [ +0,005135] PGD 0 P4D 0 [ +0,002581] Oops: 0002 [#1] PREEMPT SMP NOPTI [ +0,004359] CPU: 1 PID: 1200 Comm: kworker/u16:3 Tainted: G U 5.2.0-rc1+ #410 [ +0,008433] Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP, BIOS ICLSFWR1.R00.3175.A00.1904261428 04/26/2019 [ +0,013323] Workqueue: i915-dp i915_digport_work_func [i915] [ +0,005676] RIP: 0010:queue_work_on+0x19/0x70 [ +0,004372] Code: ff ff ff 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 41 56 49 89 f6 41 55 41 89 fd 41 54 55 53 48 89 d3 9c 5d fa e8 e7 81 0c 00 <f0> 48 0f ba 2b 00 73 31 45 31 e4 f7 c5 00 02 00 00 74 13 e8 cf 7f [ +0,018750] RSP: 0018:ffffc900007dfc50 EFLAGS: 00010006 [ +0,005222] RAX: 0000000000000046 RBX: 00000000000005a0 RCX: 0000000000000001 [ +0,007133] RDX: 000000000001b608 RSI: 0000000000000000 RDI: ffffffff82121972 [ +0,007129] RBP: 0000000000000202 R08: 0000000000000000 R09: 0000000000000001 [ +0,007129] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88847bfa5096 [ +0,007131] R13: 0000000000000010 R14: ffff88849c08f3f8 R15: 0000000000000000 [ +0,007128] FS: 0000000000000000(0000) GS:ffff88849dc80000(0000) knlGS:0000000000000000 [ +0,008083] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0,005749] CR2: 00000000000005a0 CR3: 0000000005210006 CR4: 0000000000760ee0 [ +0,007128] PKRU: 55555554 [ +0,002722] Call Trace: [ +0,002458] drm_dp_mst_handle_up_req+0x517/0x540 [drm_kms_helper] [ +0,006197] ? drm_dp_mst_hpd_irq+0x5b/0x9c0 [drm_kms_helper] [ +0,005764] drm_dp_mst_hpd_irq+0x5b/0x9c0 [drm_kms_helper] [ +0,005623] ? intel_dp_hpd_pulse+0x205/0x370 [i915] [ +0,005018] intel_dp_hpd_pulse+0x205/0x370 [i915] [ +0,004836] i915_digport_work_func+0xbb/0x140 [i915] [ +0,005108] process_one_work+0x245/0x610 [ +0,004027] worker_thread+0x37/0x380 [ +0,003684] ? process_one_work+0x610/0x610 [ +0,004184] kthread+0x119/0x130 [ +0,003240] ? kthread_park+0x80/0x80 [ +0,003668] ret_from_fork+0x24/0x50 Cc: Lyude Paul <lyude@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190523212433.9058-1-imre.deak@intel.com
-
Andrey Grodzovsky authored
Document the missing parameters. Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Signed-off-by:
-
- 28 May, 2019 5 commits
-
-
Sam Ravnborg authored
Drop use of the deprecated drmP.h header file. While touching the list of include files: - Divide include files in blocks of linux/* video/* drm/* etc. Be consistent in the order of the blocks - Sort individual blocks of include files Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190526180532.1641-3-sam@ravnborg.org
-
Sam Ravnborg authored
The num_supplies variable is not used, delete it. Build tested. Signed-off-by:
-
Maarten Lankhorst authored
This picks up rc2 for us as well. Signed-off-by:Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-
Benjamin Gaignard authored
Restore calls to clk_{enable/disable} deleted after applying the wrong version of the patch Fixes: fd6905fc ("drm/stm: ltdc: remove clk_round_rate comment") Signed-off-by:Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by:
Philippe Cornu <philippe.cornu@st.com> Signed-off-by:
-
Fabio Estevam authored
The 'clips' member is a pointer, so assign NULL instead of 0. This fixes the following sparse warning: drivers/gpu/drm/drm_damage_helper.c:289:31: warning: Using plain integer as NULL pointer Signed-off-by:
Fabio Estevam <festevam@gmail.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190527183714.11168-1-festevam@gmail.com
-
- 27 May, 2019 1 commit
-
-
git://anongit.freedesktop.org/drm/drm-intelDave Airlie authored
Features: - Engine discovery query (Tvrtko) - Support for DP YCbCr4:2:0 outputs (Gwan-gyeong) - HDCP revocation support, refactoring (Ramalingam) - Remove DRM_AUTH from IOCTLs which also have DRM_RENDER_ALLOW (Christian König) - Asynchronous display power disabling (Imre) - Perma-pin uC firmware and re-enable global reset (Fernando) - GTT remapping for display, for bigger fb size and stride (Ville) - Enable pipe HDR mode on ICL if only HDR planes are used (Ville) - Kconfig to tweak the busyspin durations for i915_wait_request (Chris) - Allow multiple user handles to the same VM (Chris) - GT/GEM runtime pm improvements using wakerefs (Chris) - Gen 4&5 render context support (Chris) - Allow userspace to clone contexts on creation (Chris) - SINGLE_TIMELINE flags for context creation (Chris) - Allow specification of parallel execbuf (Chris) Refactoring: - Header refactoring (Jani) - Move GraphicsTechnology files under gt/ (Chris) - Sideband code refactoring (Chris) Fixes: - ICL DSI state readout and checker fixes (Vandita) - GLK DSI picture corruption fix (Stanislav) - HDMI deep color fixes (Clinton, Aditya) - Fix driver unbinding from a device in use (Janusz) - Fix clock gating with pipe scaling (Radhakrishna) - Disable broken FBC on GLK (Daniel Drake) - Miscellaneous GuC fixes (Michal) - Fix MG PHY DP register programming (Imre) - Add missing combo PHY lane power setup (Imre) - Workarounds for early ICL VBT issues (Imre) - Fix fastset vs. pfit on/off on HSW EDP transcoder (Ville) - Add readout and state check for pch_pfit.force_thru (Ville) - Miscellaneous display fixes and refactoring (Ville) - Display workaround fixes (Ville) - Enable audio even if ELD is bogus (Ville) - Fix use-after-free in reporting create.size (Chris) - Sideband fixes to avoid BYT hard lockups (Chris) - Workaround fixes and improvements (Chris) Maintainer shortcomings: - Failure to adequately describe and give credit for all changes (Jani) Signed-off-by:
Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87sgt3n45z.fsf@intel.com
-
