- 20 May, 2017 40 commits
-
-
Mike Marciniszyn authored
commit b6eac931 upstream. The driver progress routines can call cond_resched() when a timeslice is exhausted and irqs are enabled. If the ULP had been holding a spin lock without disabling irqs and the post send directly called the progress routine, the cond_resched() could yield allowing another thread from the same ULP to deadlock on that same lock. Correct by replacing the current hfi1_do_send() calldown with a unique one for post send and adding an argument to hfi1_do_send() to indicate that the send engine is running in a thread. If the routine is not running in a thread, avoid calling cond_resched(). Fixes: Commit 831464ce ("IB/hfi1: Don't call cond_resched in atomic mode when sending packets") Reviewed-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jack Morgenstein authored
commit fb7a9174 upstream. A warning message during SRIOV multicast cleanup should have actually been a debug level message. The condition generating the warning does no harm and can fill the message log. In some cases, during testing, some tests were so intense as to swamp the message log with these warning messages, causing a stall in the console message log output task. This stall caused an NMI to be sent to all CPUs (so that they all dumped their stacks into the message log). Aside from the message flood causing an NMI, the tests all passed. Once the message flood which caused the NMI is removed (by reducing the warning message to debug level), the NMI no longer occurs. Sample message log (console log) output illustrating the flood and resultant NMI (snippets with comments and modified with ... instead of hex digits, to satisfy checkpatch.pl): <mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!... *** About 4000 almost identical lines in less than one second *** <mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!... INFO: rcu_sched detected stalls on CPUs/tasks: { 17} (...) *** { 17} above indicates that CPU 17 was the one that stalled *** sending NMI to all CPUs: ... NMI backtrace for cpu 17 CPU: 17 PID: 45909 Comm: kworker/17:2 Hardware name: HP ProLiant DL360p Gen8, BIOS P71 09/08/2013 Workqueue: events fb_flashcursor task: ffff880478...... ti: ffff88064e...... task.ti: ffff88064e...... RIP: 0010:[ffffffff81......] [ffffffff81......] io_serial_in+0x15/0x20 RSP: 0018:ffff88064e257cb0 EFLAGS: 00000002 RAX: 0000000000...... RBX: ffffffff81...... RCX: 0000000000...... RDX: 0000000000...... RSI: 0000000000...... RDI: ffffffff81...... RBP: ffff88064e...... R08: ffffffff81...... R09: 0000000000...... R10: 0000000000...... R11: ffff88064e...... R12: 0000000000...... R13: 0000000000...... R14: ffffffff81...... R15: 0000000000...... FS: 0000000000......(0000) GS:ffff8804af......(0000) knlGS:000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080...... CR2: 00007f2a2f...... CR3: 0000000001...... CR4: 0000000000...... DR0: 0000000000...... DR1: 0000000000...... DR2: 0000000000...... DR3: 0000000000...... DR6: 00000000ff...... DR7: 0000000000...... Stack: ffff88064e...... ffffffff81...... ffffffff81...... 0000000000...... ffffffff81...... ffff88064e...... ffffffff81...... ffffffff81...... ffffffff81...... ffff88064e...... ffffffff81...... 0000000000...... Call Trace: [<ffffffff813d099b>] wait_for_xmitr+0x3b/0xa0 [<ffffffff813d0b5c>] serial8250_console_putchar+0x1c/0x30 [<ffffffff813d0b40>] ? serial8250_console_write+0x140/0x140 [<ffffffff813cb5fa>] uart_console_write+0x3a/0x80 [<ffffffff813d0aae>] serial8250_console_write+0xae/0x140 [<ffffffff8107c4d1>] call_console_drivers.constprop.15+0x91/0xf0 [<ffffffff8107d6cf>] console_unlock+0x3bf/0x400 [<ffffffff813503cd>] fb_flashcursor+0x5d/0x140 [<ffffffff81355c30>] ? bit_clear+0x120/0x120 [<ffffffff8109d5fb>] process_one_work+0x17b/0x470 [<ffffffff8109e3cb>] worker_thread+0x11b/0x400 [<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400 [<ffffffff810a5aef>] kthread+0xcf/0xe0 [<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140 [<ffffffff81645858>] ret_from_fork+0x58/0x90 [<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140 Code: 48 89 e5 d3 e6 48 63 f6 48 03 77 10 8b 06 5d c3 66 0f 1f 44 00 00 66 66 66 6 As indicated in the stack trace above, the console output task got swamped. Fixes: b9c5d6a6 ("IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
-
Jack Morgenstein authored
commit 99e68909 upstream. In mlx4_ib_add, procedure mlx4_ib_alloc_eqs is called to allocate EQs. However, in the mlx4_ib_add error flow, procedure mlx4_ib_free_eqs is not called to free the allocated EQs. Fixes: e605b743 ("IB/mlx4: Increase the number of vectors (EQs) available for ULPs") Signed-off-by:
-
Shamir Rabinovitch authored
commit 771a5258 upstream. When udev renames the netdev devices, ipoib debugfs entries does not get renamed. As a result, if subsequent probe of ipoib device reuse the name then creating a debugfs entry for the new device would fail. Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part of ipoib event handling in order to avoid any race condition between these. Fixes: 1732b0ef ([IPoIB] add path record information in debugfs) Signed-off-by:
Vijay Kumar <vijay.ac.kumar@oracle.com> Signed-off-by:
Shamir Rabinovitch <shamir.rabinovitch@oracle.com> Reviewed-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
-
Michael J. Ruhl authored
commit 8561eae6 upstream. The Infiniband spec defines "A multicast address is defined by a MGID and a MLID" (section 10.5). Currently the MLID value is not validated. Add check to verify that the MLID value is in the correct address range. Fixes: 0c33aeed ("[IB] Add checks to multicast attach and detach") Reviewed-by:
Ira Weiny <ira.weiny@intel.com> Reviewed-by:
Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com> Signed-off-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
commit b312be3d upstream. The kernel commit cited below restructured ib device management so that the device kobject is initialized in ib_alloc_device. As part of the restructuring, the kobject is now initialized in procedure ib_alloc_device, and is later added to the device hierarchy in the ib_register_device call stack, in procedure ib_device_register_sysfs (which calls device_add). However, in the ib_device_register_sysfs error flow, if an error occurs following the call to device_add, the cleanup procedure device_unregister is called. This call results in the device object being deleted -- which results in various use-after-free crashes. The correct cleanup call is device_del -- which undoes device_add without deleting the device object. The device object will then (correctly) be deleted in the ib_register_device caller's error cleanup flow, when the caller invokes ib_dealloc_device. Fixes: 55aeed06 ("IB/core: Make ib_alloc_device init the kobject") Signed-off-by:
-
Ding Tianhong authored
commit a6a59932 upstream. The patch 32786821 (make skb_copy_datagram_msg() et.al. preserve ->msg_iter on error) will revert the iov buffer if copy to iter failed, but it didn't copy any datagram if the skb_checksum_complete error, so no need to revert any data at this place. v2: Sabrina notice that return -EFAULT when checksum error is not correct here, it would confuse the caller about the return value, so fix it. Fixes: 32786821 ("make skb_copy_datagram_msg() et.al. preserve->msg_iter on error") Signed-off-by:
Ding Tianhong <dingtianhong@huawei.com> Acked-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Alex Williamson authored
commit 0cfef2b7 upstream. If the mmap_sem is contented then the vfio type1 IOMMU backend will defer locked page accounting updates to a workqueue task. This has a few problems and depending on which side the user tries to play, they might be over-penalized for unmaps that haven't yet been accounted or race the workqueue to enter more mappings than they're allowed. The original intent of this workqueue mechanism seems to be focused on reducing latency through the ioctl, but we cannot do so at the cost of correctness. Remove this workqueue mechanism and update the callers to allow for failure. We can also now recheck the limit under write lock to make sure we don't exceed it. vfio_pin_pages_remote() also now necessarily includes an unwind path which we can jump to directly if the consecutive page pinning finds that we're exceeding the user's memory limits. This avoids the current lazy approach which does accounting and mapping up to the fault, only to return an error on the next iteration to unwind the entire vfio_dma. Reviewed-by:
Peter Xu <peterx@redhat.com> Reviewed-by:
Kirti Wankhede <kwankhede@nvidia.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Dennis Yang authored
commit 948f581a upstream. dm-thin does not free the discard_parent bio after all chained sub bios finished. The following kmemleak report could be observed after pool with discard_passdown option processes discard bios in linux v4.11-rc7. To fix this, we drop the discard_parent bio reference when its endio (passdown_endio) called. unreferenced object 0xffff8803d6b29700 (size 256): comm "kworker/u8:0", pid 30349, jiffies 4379504020 (age 143002.776s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 01 00 00 00 00 00 00 f0 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff81a5efd9>] kmemleak_alloc+0x49/0xa0 [<ffffffff8114ec34>] kmem_cache_alloc+0xb4/0x100 [<ffffffff8110eec0>] mempool_alloc_slab+0x10/0x20 [<ffffffff8110efa5>] mempool_alloc+0x55/0x150 [<ffffffff81374939>] bio_alloc_bioset+0xb9/0x260 [<ffffffffa018fd20>] process_prepared_discard_passdown_pt1+0x40/0x1c0 [dm_thin_pool] [<ffffffffa018b409>] break_up_discard_bio+0x1a9/0x200 [dm_thin_pool] [<ffffffffa018b484>] process_discard_cell_passdown+0x24/0x40 [dm_thin_pool] [<ffffffffa018b24d>] process_discard_bio+0xdd/0xf0 [dm_thin_pool] [<ffffffffa018ecf6>] do_worker+0xa76/0xd50 [dm_thin_pool] [<ffffffff81086239>] process_one_work+0x139/0x370 [<ffffffff810867b1>] worker_thread+0x61/0x450 [<ffffffff8108b316>] kthread+0xd6/0xf0 [<ffffffff81a6cd1f>] ret_from_fork+0x3f/0x70 [<ffffffffffffffff>] 0xffffffffffffffff Signed-off-by:
Dennis Yang <dennisyang@qnap.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit 23a60124 upstream. Otherwise the request-based DM blk-mq request_queue will be put into service without being properly exported via sysfs. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Somasundaram Krishnasamy authored
commit 117aceb0 upstream. When committing era metadata to disk, it doesn't always save the latest spacemap metadata root in superblock. Due to this, metadata is getting corrupted sometimes when reopening the device. The correct order of update should be, pre-commit (shadows spacemap root), save the spacemap root (newly shadowed block) to in-core superblock and then the final commit. Signed-off-by:
Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com> Signed-off-by:
-
Gary R Hook authored
commit 6263b51e upstream. The CCP has the ability to perform several operations simultaneously, but only one interrupt. When implemented as a PCI device and using MSI-X/MSI interrupts, use a tasklet model to service interrupts. By disabling and enabling interrupts from the CCP, coupled with the queuing that tasklets provide, we can ensure that all events (occurring on the device) are recognized and serviced. This change fixes a problem wherein 2 or more busy queues can cause notification bits to change state while a (CCP) interrupt is being serviced, but after the queue state has been evaluated. This results in the event being 'lost' and the queue hanging, waiting to be serviced. Since the status bits are never fully de-asserted, the CCP never generates another interrupt (all bits zero -> one or more bits one), and no further CCP operations will be executed. Signed-off-by:
Gary R Hook <gary.hook@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Gary R Hook authored
commit 7b537b24 upstream. The CCP has the ability to perform several operations simultaneously, but only one interrupt. When implemented as a PCI device and using MSI-X/MSI interrupts, use a tasklet model to service interrupts. By disabling and enabling interrupts from the CCP, coupled with the queuing that tasklets provide, we can ensure that all events (occurring on the device) are recognized and serviced. This change fixes a problem wherein 2 or more busy queues can cause notification bits to change state while a (CCP) interrupt is being serviced, but after the queue state has been evaluated. This results in the event being 'lost' and the queue hanging, waiting to be serviced. Since the status bits are never fully de-asserted, the CCP never generates another interrupt (all bits zero -> one or more bits one), and no further CCP operations will be executed. Signed-off-by:
-
Gary R Hook authored
commit 116591fe upstream. Ensure that we disable interrupts first when shutting down the driver. Signed-off-by:
Gary R Hook <ghook@amd.com> Signed-off-by:
-
Gary R Hook authored
commit 56467cb1 upstream. Each CCP queue can product interrupts for 4 conditions: operation complete, queue empty, error, and queue stopped. This driver only works with completion and error events. Signed-off-by:
-
Stephan Mueller authored
commit 2a2a251f upstream. Some cipher implementations will crash if you try to use them without calling setkey first. This patch adds a check so that the accept(2) call will fail with -ENOKEY if setkey hasn't been done on the socket yet. Fixes: 400c40cf ("crypto: algif - add AEAD support") Signed-off-by:
Stephan Mueller <smueller@chronox.de> Signed-off-by:
-
Mike Snitzer authored
commit 2859323e upstream. When registering an integrity profile: if the template's interval_exp is not 0 use it, otherwise use the ilog2() of logical block size of the provided gendisk. This fixes a long-standing DM linear target bug where it cannot pass integrity data to the underlying device if its logical block size conflicts with the underlying device's logical block size. Reported-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Marc Zyngier authored
commit c667186f upstream. Our 32bit CP14/15 handling inherited some of the ARMv7 code for handling the trapped system registers, completely missing the fact that the fields for Rt and Rt2 are now 5 bit wide, and not 4... Let's fix it, and provide an accessor for the most common Rt case. Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Andrew Jones authored
commit 6c7a5dce upstream. Fix potential races in kvm_psci_vcpu_on() by taking the kvm->lock mutex. In general, it's a bad idea to allow more than one PSCI_CPU_ON to process the same target VCPU at the same time. One such problem that may arise is that one PSCI_CPU_ON could be resetting the target vcpu, which fills the entire sys_regs array with a temporary value including the MPIDR register, while another looks up the VCPU based on the MPIDR value, resulting in no target VCPU found. Resolves both races found with the kvm-unit-tests/arm/psci unit test. Reviewed-by:
Levente Kurusa <lkurusa@redhat.com> Suggested-by:
Andrew Jones <drjones@redhat.com> Signed-off-by:
-
David Hildenbrand authored
commit 28bf2888 upstream. If we already entered/are about to enter SMM, don't allow switching to INIT/SIPI_RECEIVED, otherwise the next call to kvm_apic_accept_events() will report a warning. Same applies if we are already in MP state INIT_RECEIVED and SMM is requested to be turned on. Refuse to set the VCPU events in this case. Fixes: cd7764fe ("KVM: x86: latch INITs while in system management mode") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Vince Weaver authored
commit 33b88e70 upstream. It appears as though the Broadwell-EP DRAM units share the special units quirk with Haswell-EP/KNL. Without this patch, you get really high results (a single DRAM using 20W of power). The powercap driver in drivers/powercap/intel_rapl.c already has this change. Signed-off-by:
Vince Weaver <vincent.weaver@maine.edu> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@gmail.com> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Richard Weinberger authored
commit 9abc74a2 upstream. This is broken since ever but sadly nobody noticed. Recent versions of GDB set DR_CONTROL unconditionally and UML dies due to a heap corruption. It turns out that the PTRACE_POKEUSER was copy&pasted from i386 and assumes that addresses are 4 bytes long. Fix that by using 8 as address size in the calculation. Reported-by:
jie cao <cj3054@gmail.com> Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Ben Hutchings authored
commit 8376efd3 upstream. Commit 11e63f6d added cache flushing for unaligned writes from an iovec, covering the first and last cache line of a >= 8 byte write and the first cache line of a < 8 byte write. But an unaligned write of 2-7 bytes can still cover two cache lines, so make sure we flush both in that case. Fixes: 11e63f6d ("x86, pmem: fix broken __copy_user_nocache ...") Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Andy Lutomirski authored
commit 65973dd3 upstream. i386 glibc is buggy and calls the sigaction syscall incorrectly. This is asymptomatic for normal programs, but it blows up on programs that do evil things with segmentation. The ldt_gdt self-test is an example of such an evil program. This doesn't appear to be a regression -- I think I just got lucky with the uninitialized memory that glibc threw at the kernel when I wrote the test. This hackish fix manually issues sigaction(2) syscalls to undo the damage. Without the fix, ldt_gdt_32 segfaults; with the fix, it passes for me. See: https://sourceware.org/bugzilla/show_bug.cgi?id=21269Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/aaab0f9f93c9af25396f01232608c163a760a668.1490218061.git.luto@kernel.orgSigned-off-by:
-
Ashish Kalra authored
commit d594aa02 upstream. The minimum size for a new stack (512 bytes) setup for arch/x86/boot components when the bootloader does not setup/provide a stack for the early boot components is not "enough". The setup code executing as part of early kernel startup code, uses the stack beyond 512 bytes and accidentally overwrites and corrupts part of the BSS section. This is exposed mostly in the early video setup code, where it was corrupting BSS variables like force_x, force_y, which in-turn affected kernel parameters such as screen_info (screen_info.orig_video_cols) and later caused an exception/panic in console_init(). Most recent boot loaders setup the stack for early boot components, so this stack overwriting into BSS section issue has not been exposed. Signed-off-by:
Ashish Kalra <ashish@bluestacks.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170419152015.10011-1-ashishkalra@Ashishs-MacBook-Pro.localSigned-off-by:
-
Guenter Roeck authored
commit f5cccf49 upstream. While running a bind/unbind stress test with the dwc3 usb driver on rk3399, the following crash was observed. Unable to handle kernel NULL pointer dereference at virtual address 00000218 pgd = ffffffc00165f000 [00000218] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async ppp_generic slhc tun CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507 Hardware name: Google Kevin (DT) Workqueue: pm pm_runtime_work task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000 PC is at autosuspend_check+0x74/0x174 LR is at autosuspend_check+0x70/0x174 ... Call trace: [<ffffffc00080dcc0>] autosuspend_check+0x74/0x174 [<ffffffc000810500>] usb_runtime_idle+0x20/0x40 [<ffffffc000785ae0>] __rpm_callback+0x48/0x7c [<ffffffc000786af0>] rpm_idle+0x1e8/0x498 [<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Source: (gdb) l *0xffffffc00080dcc0 0xffffffc00080dcc0 is in autosuspend_check (drivers/usb/core/driver.c:1778). 1773 /* We don't need to check interfaces that are 1774 * disabled for runtime PM. Either they are unbound 1775 * or else their drivers don't support autosuspend 1776 * and so they are permanently active. 1777 */ 1778 if (intf->dev.power.disable_depth) 1779 continue; 1780 if (atomic_read(&intf->dev.power.usage_count) > 0) 1781 return -EBUSY; 1782 w |= intf->needs_remote_wakeup; Code analysis shows that intf is set to NULL in usb_disable_device() prior to setting actconfig to NULL. At the same time, usb_runtime_idle() does not lock the usb device, and neither does any of the functions in the traceback. This means that there is no protection against a race condition where usb_disable_device() is removing dev->actconfig->interface[] pointers while those are being accessed from autosuspend_check(). To solve the problem, synchronize and validate device state between autosuspend_check() and usb_disconnect(). Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Guenter Roeck authored
commit 245b2eec upstream. While stress testing a usb controller using a bind/unbind looop, the following error loop was observed. usb 7-1.2: new low-speed USB device number 3 using xhci-hcd usb 7-1.2: hub failed to enable device, error -108 usb 7-1-port2: cannot disable (err = -22) usb 7-1-port2: couldn't allocate usb_device usb 7-1-port2: cannot disable (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) ** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22 ** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22) This continues forever. After adding tracebacks into the code, the call sequence leading to this is found to be as follows. [<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8 [<ffffffc0007fceb4>] hub_resume+0x2c/0x3c [<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158 [<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288 [<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98 [<ffffffc0007820a0>] __rpm_callback+0x48/0x7c [<ffffffc00078217c>] rpm_callback+0xa8/0xd4 [<ffffffc000786234>] rpm_suspend+0x84/0x758 [<ffffffc000786ca4>] rpm_idle+0x2c8/0x498 [<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac [<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c [<ffffffc000803798>] hub_event+0x10ac/0x12ac [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 kick_hub_wq() is called from hub_activate() even after failures to communicate with the hub. This results in an endless sequence of hub event -> hub activate -> wq trigger -> hub event -> ... Provide two solutions for the problem. - Only trigger the hub event queue if communication with the hub is successful. - After a suspend failure, only resume already suspended interfaces if the communication with the device is still possible. Each of the changes fixes the observed problem. Use both to improve robustness. Acked-by:
-
Alexey Brodkin authored
commit 3d615964 upstream. DWC3 driver uses of_usb_get_phy_mode() which is implemented in drivers/usb/phy/of.c and in bare minimal configuration it might not be pulled in kernel binary. In case of ARC or ARM this could be easily reproduced with "allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m. On building all ends-up with: ---------------------->8------------------ Kernel: arch/arm/boot/Image is ready Kernel: arch/arm/boot/zImage is ready Building modules, stage 2. MODPOST 5 modules ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined! make[1]: *** [__modpost] Error 1 make: *** [modules] Error 2 ---------------------->8------------------ Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Felipe Balbi <balbi@kernel.org> Cc: Felix Fietkau <nbd@nbd.name> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: linux-snps-arc@lists.infradead.org Signed-off-by:
-
Romain Izard authored
commit 6e253d0f upstream. With commit bc49d1d1 ("usb: gadget: don't couple configfs to legacy gadgets"),it is possible to build a modular kernel with both built-in configfs support and modular legacy gadget drivers. But when building a kernel without modules, it is also necessary to be able to build with configfs but without any legacy gadget driver. This was a possible configuration when the USB_CONFIGFS was a part of the choice options, but not anymore. Mark the choice for legacy gadget drivers as optional restores this. Fixes: bc49d1d1 ("usb: gadget: don't couple configfs to legacy gadgets") Signed-off-by:
Romain Izard <romain.izard.pro@gmail.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 2c930e3d upstream. Add missing continue in switch. Addresses-Coverity-ID: 1248733 Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by:
-
Ian Abbott authored
commit 8ec04a49 upstream. The timer expiry routine `jr3_pci_poll_dev()` checks for expiry by checking whether the absolute value of `jiffies` (stored in local variable `now`) is greater than the expected expiry time in jiffy units. This will fail when `jiffies` wraps around. Also, it seems to make sense to handle the expiry one jiffy earlier than the current test. Use `time_after_eq()` to check for expiry. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Ian Abbott authored
commit 45292be0 upstream. For some reason, the driver does not consider allocation of the subdevice private data to be a fatal error when attaching the COMEDI device. It tests the subdevice private data pointer for validity at certain points, but omits some crucial tests. In particular, `jr3_pci_auto_attach()` calls `jr3_pci_alloc_spriv()` to allocate and initialize the subdevice private data, but the same function subsequently dereferences the pointer to access the `next_time_min` and `next_time_max` members without checking it first. The other missing test is in the timer expiry routine `jr3_pci_poll_dev()`, but it will crash before it gets that far. Fix the bug by returning `-ENOMEM` from `jr3_pci_auto_attach()` as soon as one of the calls to `jr3_pci_alloc_spriv()` returns `NULL`. The COMEDI core will subsequently call `jr3_pci_detach()` to clean up. Signed-off-by:
-
Johan Hovold authored
commit b58f45c8 upstream. Make sure to deregister the USB driver before releasing the tty driver to avoid use-after-free in the USB disconnect callback where the tty devices are deregistered. Fixes: 61e12104 ("staging: gdm7240: adding LTE USB driver") Cc: Won Kang <wkang77@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Malcolm Priestley authored
commit 12ecd24e upstream. Since 4.9 mandated USB buffers be heap allocated this causes the driver to fail. Since there is a wide range of buffer sizes use kmemdup to create allocated buffer. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
Malcolm Priestley authored
commit 05c0cf88 upstream. Since 4.9 mandated USB buffers to be heap allocated. This causes the driver to fail. Create buffer for USB transfers. Signed-off-by:
-
Bjørn Mork authored
commit 19445816 upstream. This reverts commit 833415a3 ("cdc-wdm: fix "out-of-sync" due to missing notifications") There have been several reports of wdm_read returning unexpected EIO errors with QMI devices using the qmi_wwan driver. The reporters confirm that reverting prevents these errors. I have been unable to reproduce the bug myself, and have no explanation to offer either. But reverting is the safe choice here, given that the commit was an attempt to work around a firmware problem. Living with a firmware problem is still better than adding driver bugs. Reported-by:
Kasper Holtze <kasper@holtze.dk> Reported-by:
Aleksander Morgado <aleksander@aleksander.es> Reported-by:
Daniele Palmas <dnlplm@gmail.com> Fixes: 833415a3 ("cdc-wdm: fix "out-of-sync" due to missing notifications") Signed-off-by:
Bjørn Mork <bjorn@mork.no> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Ajay Kaher authored
USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously commit 2f86a96b upstream. There is race condition when two USB class drivers try to call init_usb_class at the same time and leads to crash. code path: probe->usb_register_dev->init_usb_class To solve this, mutex locking has been added in init_usb_class() and destroy_usb_class(). As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class() because usb_class can never be NULL there. Signed-off-by:
Ajay Kaher <ajay.kaher@samsung.com> Acked-by:
-
Marek Vasut authored
commit 31c5d192 upstream. This development kit has an FT4232 on it with a custom USB VID/PID. The FT4232 provides four UARTs, but only two are used. The UART 0 is used by the FlashPro5 programmer and UART 2 is connected to the SmartFusion2 CortexM3 SoC UART port. Note that the USB VID is registered to Actel according to Linux USB VID database, but that was acquired by Microsemi. Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Peter Chen authored
commit 6fc091fb upstream. Print correct command ring address using 'val_64'. Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Roger Quadros authored
commit 69307ccb upstream. As per [1] issue #4, "The periodic EP scheduler always tries to schedule the EPs that have large intervals (interval equal to or greater than 128 microframes) into different microframes. So it maintains an internal counter and increments for each large interval EP added. When the counter is greater than 128, the scheduler rejects the new EP. So when the hub re-enumerated 128 times, it triggers this condition." This results in Bandwidth error when devices with periodic endpoints (ISO/INT) having bInterval > 7 are plugged and unplugged several times on a TUSB73x0 XHCI host. Workaround this issue by limiting the bInterval to 7 (i.e. interval to 6) for High-speed or faster periodic endpoints. [1] - http://www.ti.com/lit/er/sllz076/sllz076.pdfSigned-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
