Skip to content

L
linux
Switch branch/tag
  1. 03 Dec, 2018 7 commits
    • Jean-Philippe Brucker's avatar
      vhost: fix IOTLB locking · e3f78718
      Jean-Philippe Brucker authored 
      Commit 78139c94 ("net: vhost: lock the vqs one by one") moved the vq
lock to improve scalability, but introduced a possible deadlock in
vhost-iotlb. vhost_iotlb_notify_vq() now takes vq->mutex while holding
the device's IOTLB spinlock. And on the vhost_iotlb_miss() path, the
spinlock is taken while holding vq->mutex.

Since calling vhost_poll_queue() doesn't require any lock, avoid the
deadlock by not taking vq->mutex.

Fixes: 78139c94 ("net: vhost: lock the vqs one by one")
Acked-by: default avatarJason Wang <jasowang@redhat.com>
Acked-by: default avatarMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: default avatarJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e3f78718
    • David S. Miller's avatar
      Merge branch 'phy-micrel-toggling-reset' · 4763c9f9
      David S. Miller authored 
      Yoshihiro Shimoda says:

====================
net: phy: micrel: add toggling phy reset

This patch set is for R-Car Gen3 Salvator-XS boards. If we do
the following method, the phy cannot link up correctly.

 1) Kernel boots by using initramfs.
 --> No open the nic, so phy_device_register() and phy_probe()
     deasserts the reset.
 2) Kernel enters the suspend.
 --> So, keep the reset signal as deassert.
 --> On R-Car Salvator-XS board, unfortunately, the board power is
     turned off.
 3) Kernel returns from suspend.
 4) ifconfig eth0 up
 --> Then, since edge signal of the reset doesn't happen,
     it cannot link up.
 5) ifconfig eth0 down
 6) ifconfig eth0 up
 --> In this case, it can link up.

When resolving this issue after I got feedback from Andrew and Heiner,
I found an issue that the phy_device.c didn't call phy_resume()
if the PHY was not attached. So, patch 1 fixes it and add toggling
the phy reset to the micrel phy driver.

Changes from v1 (as RFC):
 - No remove the current code of phy_device.c to avoid any side effects.
 - Fix the mdio_bus_phy_resume() in phy_device.c.
 - Add toggling the phy reset in micrel.c if the PHY is not attached.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      4763c9f9
    • Yoshihiro Shimoda's avatar
      net: phy: micrel: add toggling phy reset if PHY is not attached · 8c85f4b8
      Yoshihiro Shimoda authored 
      This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:

 1) Kernel boots by using initramfs.
 --> No open the nic, so phy_device_register() and phy_probe()
     deasserts the reset.
 2) Kernel enters the suspend.
 --> So, keep the reset signal as deassert.
 --> On R-Car Salvator-XS board, unfortunately, the board power is
     turned off.
 3) Kernel returns from suspend.
 4) ifconfig eth0 up
 --> Then, since edge signal of the reset doesn't happen,
     it cannot link up.
 5) ifconfig eth0 down
 6) ifconfig eth0 up
 --> In this case, it can link up.
Reported-by: default avatarHiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: default avatarYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      8c85f4b8
    • Yoshihiro Shimoda's avatar
      net: phy: Fix not to call phy_resume() if PHY is not attached · ef1b5bf5
      Yoshihiro Shimoda authored 
      This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.

Fixes: 803dd9c7 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: default avatarYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ef1b5bf5
    • Prashant Bhole's avatar
      tun: remove skb access after netif_receive_skb · 4e4b08e5
      Prashant Bhole authored 
      In tun.c skb->len was accessed while doing stats accounting after a
call to netif_receive_skb. We can not access skb after this call
because buffers may be dropped.

The fix for this bug would be to store skb->len in local variable and
then use it after netif_receive_skb(). IMO using xdp data size for
accounting bytes will be better because input for tun_xdp_one() is
xdp_buff.

Hence this patch:
- fixes a bug by removing skb access after netif_receive_skb()
- uses xdp data size for accounting bytes

[613.019057] BUG: KASAN: use-after-free in tun_sendmsg+0x77c/0xc50 [tun]
[613.021062] Read of size 4 at addr ffff8881da9ab7c0 by task vhost-1115/1155
[613.023073]
[613.024003] CPU: 0 PID: 1155 Comm: vhost-1115 Not tainted 4.20.0-rc3-vm+ #232
[613.026029] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[613.029116] Call Trace:
[613.031145]  dump_stack+0x5b/0x90
[613.032219]  print_address_description+0x6c/0x23c
[613.034156]  ? tun_sendmsg+0x77c/0xc50 [tun]
[613.036141]  kasan_report.cold.5+0x241/0x308
[613.038125]  tun_sendmsg+0x77c/0xc50 [tun]
[613.040109]  ? tun_get_user+0x1960/0x1960 [tun]
[613.042094]  ? __isolate_free_page+0x270/0x270
[613.045173]  vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.047127]  ? peek_head_len.part.13+0x90/0x90 [vhost_net]
[613.049096]  ? get_tx_bufs+0x5a/0x2c0 [vhost_net]
[613.051106]  ? vhost_enable_notify+0x2d8/0x420 [vhost]
[613.053139]  handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.053139]  ? vhost_net_buf_peek+0x340/0x340 [vhost_net]
[613.053139]  ? __mutex_lock+0x8d9/0xb30
[613.053139]  ? finish_task_switch+0x8f/0x3f0
[613.053139]  ? handle_tx+0x32/0x120 [vhost_net]
[613.053139]  ? mutex_trylock+0x110/0x110
[613.053139]  ? finish_task_switch+0xcf/0x3f0
[613.053139]  ? finish_task_switch+0x240/0x3f0
[613.053139]  ? __switch_to_asm+0x34/0x70
[613.053139]  ? __switch_to_asm+0x40/0x70
[613.053139]  ? __schedule+0x506/0xf10
[613.053139]  handle_tx+0xc7/0x120 [vhost_net]
[613.053139]  vhost_worker+0x166/0x200 [vhost]
[613.053139]  ? vhost_dev_init+0x580/0x580 [vhost]
[613.053139]  ? __kthread_parkme+0x77/0x90
[613.053139]  ? vhost_dev_init+0x580/0x580 [vhost]
[613.053139]  kthread+0x1b1/0x1d0
[613.053139]  ? kthread_park+0xb0/0xb0
[613.053139]  ret_from_fork+0x35/0x40
[613.088705]
[613.088705] Allocated by task 1155:
[613.088705]  kasan_kmalloc+0xbf/0xe0
[613.088705]  kmem_cache_alloc+0xdc/0x220
[613.088705]  __build_skb+0x2a/0x160
[613.088705]  build_skb+0x14/0xc0
[613.088705]  tun_sendmsg+0x4f0/0xc50 [tun]
[613.088705]  vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.088705]  handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.088705]  handle_tx+0xc7/0x120 [vhost_net]
[613.088705]  vhost_worker+0x166/0x200 [vhost]
[613.088705]  kthread+0x1b1/0x1d0
[613.088705]  ret_from_fork+0x35/0x40
[613.088705]
[613.088705] Freed by task 1155:
[613.088705]  __kasan_slab_free+0x12e/0x180
[613.088705]  kmem_cache_free+0xa0/0x230
[613.088705]  ip6_mc_input+0x40f/0x5a0
[613.088705]  ipv6_rcv+0xc9/0x1e0
[613.088705]  __netif_receive_skb_one_core+0xc1/0x100
[613.088705]  netif_receive_skb_internal+0xc4/0x270
[613.088705]  br_pass_frame_up+0x2b9/0x2e0
[613.088705]  br_handle_frame_finish+0x2fb/0x7a0
[613.088705]  br_handle_frame+0x30f/0x6c0
[613.088705]  __netif_receive_skb_core+0x61a/0x15b0
[613.088705]  __netif_receive_skb_one_core+0x8e/0x100
[613.088705]  netif_receive_skb_internal+0xc4/0x270
[613.088705]  tun_sendmsg+0x738/0xc50 [tun]
[613.088705]  vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.088705]  handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.088705]  handle_tx+0xc7/0x120 [vhost_net]
[613.088705]  vhost_worker+0x166/0x200 [vhost]
[613.088705]  kthread+0x1b1/0x1d0
[613.088705]  ret_from_fork+0x35/0x40
[613.088705]
[613.088705] The buggy address belongs to the object at ffff8881da9ab740
[613.088705]  which belongs to the cache skbuff_head_cache of size 232

Fixes: 043d222f ("tuntap: accept an array of XDP buffs through sendmsg()")
Reviewed-by: default avatarToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: default avatarPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: default avatarJason Wang <jasowang@redhat.com>
Acked-by: default avatarMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      4e4b08e5
    • Su Yanjun's avatar
      net: 8139cp: fix a BUG triggered by changing mtu with network traffic · a5d4a892
      Su Yanjun authored 
      When changing mtu many times with traffic, a bug is triggered:

[ 1035.684037] kernel BUG at lib/dynamic_queue_limits.c:26!
[ 1035.684042] invalid opcode: 0000 [#1] SMP
[ 1035.684049] Modules linked in: loop binfmt_misc 8139cp(OE) macsec
tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag tcp_lp
fuse uinput xt_CHECKSUM iptable_mangle ipt_MASQUERADE
nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4
nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun
bridge stp llc ebtable_filter ebtables ip6table_filter devlink
ip6_tables iptable_filter sunrpc snd_hda_codec_generic snd_hda_intel
snd_hda_codec snd_hda_core snd_hwdep ppdev snd_seq iosf_mbi crc32_pclmul
parport_pc snd_seq_device ghash_clmulni_intel parport snd_pcm
aesni_intel joydev lrw snd_timer virtio_balloon sg gf128mul glue_helper
ablk_helper cryptd snd soundcore i2c_piix4 pcspkr ip_tables xfs
libcrc32c sr_mod sd_mod cdrom crc_t10dif crct10dif_generic ata_generic
[ 1035.684102]  pata_acpi virtio_console qxl drm_kms_helper syscopyarea
sysfillrect sysimgblt floppy fb_sys_fops crct10dif_pclmul
crct10dif_common ttm crc32c_intel serio_raw ata_piix drm libata 8139too
virtio_pci drm_panel_orientation_quirks virtio_ring virtio mii dm_mirror
dm_region_hash dm_log dm_mod [last unloaded: 8139cp]
[ 1035.684132] CPU: 9 PID: 25140 Comm: if-mtu-change Kdump: loaded
Tainted: G           OE  ------------ T 3.10.0-957.el7.x86_64 #1
[ 1035.684134] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 1035.684136] task: ffff8f59b1f5a080 ti: ffff8f5a2e32c000 task.ti:
ffff8f5a2e32c000
[ 1035.684149] RIP: 0010:[<ffffffffba3a40d0>]  [<ffffffffba3a40d0>]
dql_completed+0x180/0x190
[ 1035.684162] RSP: 0000:ffff8f5a75483e50  EFLAGS: 00010093
[ 1035.684162] RAX: 00000000000000c2 RBX: ffff8f5a6f91c000 RCX:
0000000000000000
[ 1035.684162] RDX: 0000000000000000 RSI: 0000000000000184 RDI:
ffff8f599fea3ec0
[ 1035.684162] RBP: ffff8f5a75483ea8 R08: 00000000000000c2 R09:
0000000000000000
[ 1035.684162] R10: 00000000000616ef R11: ffff8f5a75483b56 R12:
ffff8f599fea3e00
[ 1035.684162] R13: 0000000000000001 R14: 0000000000000000 R15:
0000000000000184
[ 1035.684162] FS:  00007fa8434de740(0000) GS:ffff8f5a75480000(0000)
knlGS:0000000000000000
[ 1035.684162] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1035.684162] CR2: 00000000004305d0 CR3: 000000024eb66000 CR4:
00000000001406e0
[ 1035.684162] Call Trace:
[ 1035.684162]  <IRQ>
[ 1035.684162]  [<ffffffffc08cbaf8>] ? cp_interrupt+0x478/0x580 [8139cp]
[ 1035.684162]  [<ffffffffba14a294>]
__handle_irq_event_percpu+0x44/0x1c0
[ 1035.684162]  [<ffffffffba14a442>] handle_irq_event_percpu+0x32/0x80
[ 1035.684162]  [<ffffffffba14a4cc>] handle_irq_event+0x3c/0x60
[ 1035.684162]  [<ffffffffba14db29>] handle_fasteoi_irq+0x59/0x110
[ 1035.684162]  [<ffffffffba02e554>] handle_irq+0xe4/0x1a0
[ 1035.684162]  [<ffffffffba7795dd>] do_IRQ+0x4d/0xf0
[ 1035.684162]  [<ffffffffba76b362>] common_interrupt+0x162/0x162
[ 1035.684162]  <EOI>
[ 1035.684162]  [<ffffffffba0c2ae4>] ? __wake_up_bit+0x24/0x70
[ 1035.684162]  [<ffffffffba1e46f5>] ? do_set_pte+0xd5/0x120
[ 1035.684162]  [<ffffffffba1b64fb>] unlock_page+0x2b/0x30
[ 1035.684162]  [<ffffffffba1e4879>] do_read_fault.isra.61+0x139/0x1b0
[ 1035.684162]  [<ffffffffba1e9134>] handle_pte_fault+0x2f4/0xd10
[ 1035.684162]  [<ffffffffba1ebc6d>] handle_mm_fault+0x39d/0x9b0
[ 1035.684162]  [<ffffffffba76f5e3>] __do_page_fault+0x203/0x500
[ 1035.684162]  [<ffffffffba76f9c6>] trace_do_page_fault+0x56/0x150
[ 1035.684162]  [<ffffffffba76ef42>] do_async_page_fault+0x22/0xf0
[ 1035.684162]  [<ffffffffba76b788>] async_page_fault+0x28/0x30
[ 1035.684162] Code: 54 c7 47 54 ff ff ff ff 44 0f 49 ce 48 8b 35 48 2f
9c 00 48 89 77 58 e9 fe fe ff ff 0f 1f 80 00 00 00 00 41 89 d1 e9 ef fe
ff ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 55 8d 42 ff 48
[ 1035.684162] RIP  [<ffffffffba3a40d0>] dql_completed+0x180/0x190
[ 1035.684162]  RSP <ffff8f5a75483e50>

It's not the same as in 7fe0ee09 patch described.
As 8139cp uses shared irq mode, other device irq will trigger
cp_interrupt to execute.

cp_change_mtu
 -> cp_close
 -> cp_open

In cp_close routine  just before free_irq(), some interrupt may occur.
In my environment, cp_interrupt exectutes and IntrStatus is 0x4,
exactly TxOk. That will cause cp_tx to wake device queue.

As device queue is started, cp_start_xmit and cp_open will run at same
time which will cause kernel BUG.

For example:
[#] for tx descriptor

At start:

[#][#][#]
num_queued=3

After cp_init_hw->cp_start_hw->netdev_reset_queue:

[#][#][#]
num_queued=0

When 8139cp starts to work then cp_tx will check
num_queued mismatchs the complete_bytes.

The patch will check IntrMask before check IntrStatus in cp_interrupt.
When 8139cp interrupt is disabled, just return.
Signed-off-by: default avatarSu Yanjun <suyj.fnst@cn.fujitsu.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a5d4a892
    • Heiner Kallweit's avatar
      net: phy: don't allow __set_phy_supported to add unsupported modes · d2a36971
      Heiner Kallweit authored 
      Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.

The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.

Fixes: f3a6bd39 ("phylib: Add phy_set_max_speed helper")
Signed-off-by: default avatarHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d2a36971
  3. 01 Dec, 2018 10 commits
  5. 30 Nov, 2018 9 commits
    • John Hurley's avatar
      nfp: flower: prevent offload if rhashtable insert fails · b5f0cf08
      John Hurley authored 
      For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.

Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.

Fixes: c01d0efa ("nfp: flower: use rhashtable for flow caching")
Signed-off-by: default avatarJohn Hurley <john.hurley@netronome.com>
Reviewed-by: default avatarPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b5f0cf08
    • John Hurley's avatar
      nfp: flower: release metadata on offload failure · 11664948
      John Hurley authored 
      Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.

Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.

Fixes: 81f3ddf2 ("nfp: add control message passing capabilities to flower offloads")
Signed-off-by: default avatarJohn Hurley <john.hurley@netronome.com>
Reviewed-by: default avatarPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      11664948
    • Toni Peltonen's avatar
      bonding: fix 802.3ad state sent to partner when unbinding slave · 3b5b3a33
      Toni Peltonen authored 
      Previously when unbinding a slave the 802.3ad implementation only told
partner that the port is not suitable for aggregation by setting the port
aggregation state from aggregatable to individual. This is not enough. If the
physical layer still stays up and we only unbinded this port from the bond there
is nothing in the aggregation status alone to prevent the partner from sending
traffic towards us. To ensure that the partner doesn't consider this
port at all anymore we should also disable collecting and distributing to
signal that this actor is going away. Also clear AD_STATE_SYNCHRONIZATION to
ensure partner exits collecting + distributing state.

I have tested this behaviour againts Arista EOS switches with mlx5 cards
(physical link stays up even when interface is down) and simulated
the same situation virtually Linux <-> Linux with two network namespaces
running two veth device pairs. In both cases setting aggregation to
individual doesn't alone prevent traffic from being to sent towards this
port given that the link stays up in partners end. Partner still keeps
it's end in collecting + distributing state and continues until timeout is
reached. In most cases this means we are losing the traffic partner sends
towards our port while we wait for timeout. This is most visible with slow
periodic time (LACP rate slow).

Other open source implementations like Open VSwitch and libreswitch, and
vendor implementations like Arista EOS, seem to disable collecting +
distributing to when doing similar port disabling/detaching/removing change.
With this patch kernel implementation would behave the same way and ensure
partner doesn't consider our actor viable anymore.
Signed-off-by: default avatarToni Peltonen <peltzi@peltzi.fi>
Signed-off-by: default avatarJay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: default avatarJonathan Toppins <jtoppins@redhat.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3b5b3a33
    • Dmitry Bogdanov's avatar
      net: aquantia: fix rx checksum offload bits · 37c4b91f
      Dmitry Bogdanov authored 
      The last set of csum offload fixes had a leak:

Checksum enabled status bits from rx descriptor were incorrectly
interpreted. Consequently all the other valid logic worked on zero bits.
That caused rx checksum offloads never to trigger.

Tested by dumping rx descriptors and validating resulting csum_level.
Reported-by: default avatarIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: default avatarDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: default avatarIgor Russkikh <igor.russkikh@aquantia.com>
Fixes: ad703c2b ("net: aquantia: invalid checksumm offload implementation")
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      37c4b91f
    • Colin Ian King's avatar
      openvswitch: fix spelling mistake "execeeds" -> "exceeds" · 43d0e960
      Colin Ian King authored 
      There is a spelling mistake in a net_warn_ratelimited message, fix this.
Signed-off-by: default avatarColin Ian King <colin.king@canonical.com>
Reviewed-by: default avatarSimon Horman <simon.horman@netronome.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      43d0e960
    • Colin Ian King's avatar
      liquidio: fix spelling mistake "deferal" -> "deferral" · 56e0e295
      Colin Ian King authored 
      There is a spelling mistake in the oct_stats_strings array, fix it.
Signed-off-by: default avatarColin Ian King <colin.king@canonical.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      56e0e295
    • Thierry Reding's avatar
      net: stmmac: Move debugfs init/exit to ->probe()/->remove() · 5f2b8b62
      Thierry Reding authored 
      Setting up and tearing down debugfs is current unbalanced, as seen by
this error during resume from suspend:

    [  752.134067] dwc-eth-dwmac 2490000.ethernet eth0: ERROR failed to create debugfs directory
    [  752.134347] dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: failed debugFS registration

The imbalance happens because the driver creates the debugfs hierarchy
when the device is opened and tears it down when the device is closed.
There's little gain in that, and it could be argued that it is even
surprising because it's not usually done for other devices. Fix the
imbalance by moving the debugfs creation and teardown to the driver's
->probe() and ->remove() implementations instead.

Note that the ring descriptors cannot be read while the interface is
down, so make sure to return an empty file when the descriptors_status
debugfs file is read.
Signed-off-by: default avatarThierry Reding <treding@nvidia.com>
Acked-by: default avatarJose Abreu <joabreu@synopsys.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      5f2b8b62
    • Xin Long's avatar
      sctp: update frag_point when stream_interleave is set · 4135cce7
      Xin Long authored 
      sctp_assoc_update_frag_point() should be called whenever asoc->pathmtu
changes, but we missed one place in sctp_association_init(). It would
cause frag_point is zero when sending data.

As says in Jakub's reproducer, if sp->pathmtu is set by socketopt, the
new asoc->pathmtu inherits it in sctp_association_init(). Later when
transports are added and their pmtu >= asoc->pathmtu, it will never
call sctp_assoc_update_frag_point() to set frag_point.

This patch is to fix it by updating frag_point after asoc->pathmtu is
set as sp->pathmtu in sctp_association_init(). Note that it moved them
after sctp_stream_init(), as stream->si needs to be set first.

Frag_point's calculation is also related with datachunk's type, so it
needs to update frag_point when stream->si may be changed in
sctp_process_init().

v1->v2:
  - call sctp_assoc_update_frag_point() separately in sctp_process_init
    and sctp_association_init, per Marcelo's suggestion.

Fixes: 2f5e3c9d ("sctp: introduce sctp_assoc_update_frag_point")
Reported-by: default avatarJakub Audykowicz <jakub.audykowicz@gmail.com>
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Acked-by: default avatarMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: default avatarNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      4135cce7
    • Christoph Paasch's avatar
      net: Prevent invalid access to skb->prev in __qdisc_drop_all · 9410d386
      Christoph Paasch authored 
      __qdisc_drop_all() accesses skb->prev to get to the tail of the
segment-list.

With commit 68d2f84a ("net: gro: properly remove skb from list")
the skb-list handling has been changed to set skb->next to NULL and set
the list-poison on skb->prev.

With that change, __qdisc_drop_all() will panic when it tries to
dereference skb->prev.

Since commit 992cba7e ("net: Add and use skb_list_del_init().")
__list_del_entry is used, leaving skb->prev unchanged (thus,
pointing to the list-head if it's the first skb of the list).
This will make __qdisc_drop_all modify the next-pointer of the list-head
and result in a panic later on:

[   34.501053] general protection fault: 0000 [#1] SMP KASAN PTI
[   34.501968] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.20.0-rc2.mptcp #108
[   34.502887] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011
[   34.504074] RIP: 0010:dev_gro_receive+0x343/0x1f90
[   34.504751] Code: e0 48 c1 e8 03 42 80 3c 30 00 0f 85 4a 1c 00 00 4d 8b 24 24 4c 39 65 d0 0f 84 0a 04 00 00 49 8d 7c 24 38 48 89 f8 48 c1 e8 03 <42> 0f b6 04 30 84 c0 74 08 3c 04
[   34.507060] RSP: 0018:ffff8883af507930 EFLAGS: 00010202
[   34.507761] RAX: 0000000000000007 RBX: ffff8883970b2c80 RCX: 1ffff11072e165a6
[   34.508640] RDX: 1ffff11075867008 RSI: ffff8883ac338040 RDI: 0000000000000038
[   34.509493] RBP: ffff8883af5079d0 R08: ffff8883970b2d40 R09: 0000000000000062
[   34.510346] R10: 0000000000000034 R11: 0000000000000000 R12: 0000000000000000
[   34.511215] R13: 0000000000000000 R14: dffffc0000000000 R15: ffff8883ac338008
[   34.512082] FS:  0000000000000000(0000) GS:ffff8883af500000(0000) knlGS:0000000000000000
[   34.513036] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   34.513741] CR2: 000055ccc3e9d020 CR3: 00000003abf32000 CR4: 00000000000006e0
[   34.514593] Call Trace:
[   34.514893]  <IRQ>
[   34.515157]  napi_gro_receive+0x93/0x150
[   34.515632]  receive_buf+0x893/0x3700
[   34.516094]  ? __netif_receive_skb+0x1f/0x1a0
[   34.516629]  ? virtnet_probe+0x1b40/0x1b40
[   34.517153]  ? __stable_node_chain+0x4d0/0x850
[   34.517684]  ? kfree+0x9a/0x180
[   34.518067]  ? __kasan_slab_free+0x171/0x190
[   34.518582]  ? detach_buf+0x1df/0x650
[   34.519061]  ? lapic_next_event+0x5a/0x90
[   34.519539]  ? virtqueue_get_buf_ctx+0x280/0x7f0
[   34.520093]  virtnet_poll+0x2df/0xd60
[   34.520533]  ? receive_buf+0x3700/0x3700
[   34.521027]  ? qdisc_watchdog_schedule_ns+0xd5/0x140
[   34.521631]  ? htb_dequeue+0x1817/0x25f0
[   34.522107]  ? sch_direct_xmit+0x142/0xf30
[   34.522595]  ? virtqueue_napi_schedule+0x26/0x30
[   34.523155]  net_rx_action+0x2f6/0xc50
[   34.523601]  ? napi_complete_done+0x2f0/0x2f0
[   34.524126]  ? kasan_check_read+0x11/0x20
[   34.524608]  ? _raw_spin_lock+0x7d/0xd0
[   34.525070]  ? _raw_spin_lock_bh+0xd0/0xd0
[   34.525563]  ? kvm_guest_apic_eoi_write+0x6b/0x80
[   34.526130]  ? apic_ack_irq+0x9e/0xe0
[   34.526567]  __do_softirq+0x188/0x4b5
[   34.527015]  irq_exit+0x151/0x180
[   34.527417]  do_IRQ+0xdb/0x150
[   34.527783]  common_interrupt+0xf/0xf
[   34.528223]  </IRQ>

This patch makes sure that skb->prev is set to NULL when entering
netem_enqueue.

Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 68d2f84a ("net: gro: properly remove skb from list")
Suggested-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarChristoph Paasch <cpaasch@apple.com>
Reviewed-by: default avatarEric Dumazet <edumazet@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9410d386
  7. 29 Nov, 2018 12 commits
  9. 28 Nov, 2018 2 commits
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · 60b54823
      Linus Torvalds authored 
      Pull networking fixes from David Miller:

 1) ARM64 JIT fixes for subprog handling from Daniel Borkmann.

 2) Various sparc64 JIT bug fixes (fused branch convergance, frame
    pointer usage detection logic, PSEODU call argument handling).

 3) Fix to use BH locking in nf_conncount, from Taehee Yoo.

 4) Fix race of TX skb freeing in ipheth driver, from Bernd Eckstein.

 5) Handle return value of TX NAPI completion properly in lan743x
    driver, from Bryan Whitehead.

 6) MAC filter deletion in i40e driver clears wrong state bit, from
    Lihong Yang.

 7) Fix use after free in rionet driver, from Pan Bian.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  s390/qeth: fix length check in SNMP processing
  net: hisilicon: remove unexpected free_netdev
  rapidio/rionet: do not free skb before reading its length
  i40e: fix kerneldoc for xsk methods
  ixgbe: recognize 1000BaseLX SFP modules as 1Gbps
  i40e: Fix deletion of MAC filters
  igb: fix uninitialized variables
  netfilter: nf_tables: deactivate expressions in rule replecement routine
  lan743x: Enable driver to work with LAN7431
  tipc: fix lockdep warning during node delete
  lan743x: fix return value for lan743x_tx_napi_poll
  net: via: via-velocity: fix spelling mistake "alignement" -> "alignment"
  qed: fix spelling mistake "attnetion" -> "attention"
  net: thunderx: fix NULL pointer dereference in nic_remove
  sctp: increase sk_wmem_alloc when head->truesize is increased
  firestream: fix spelling mistake: "Inititing" -> "Initializing"
  net: phy: add workaround for issue where PHY driver doesn't bind to the device
  usbnet: ipheth: fix potential recvmsg bug and recvmsg bug 2
  sparc: Adjust bpf JIT prologue for PSEUDO calls.
  bpf, doc: add entries of who looks over which jits
  ...
      60b54823
    • Linus Torvalds's avatar
      Merge tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa · b26b2b24
      Linus Torvalds authored 
      Pull Xtensa fixes from Max Filippov:

 - fix kernel exception on userspace access to a currently disabled
   coprocessor

 - fix coprocessor data saving/restoring in configurations with multiple
   coprocessors

 - fix ptrace access to coprocessor data on configurations with multiple
   coprocessors with high alignment requirements

* tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix coprocessor part of ptrace_{get,set}xregs
  xtensa: fix coprocessor context offset definitions
  xtensa: enable coprocessors that are being flushed
      b26b2b24
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7