There are a number of bugs here:

1) If "count" is less than sizeof(dump_data.data) then it copies
   uninitialized data.
2) If simple_write_to_buffer() returns -EFAULT then we run into a
   problem "ret < count" comparison.  "count" is an unsigned long so the
   comparison is type promoted to unsigned long and the negative returns
   become high positive values.  That also results in copying
   uninitialized data.
3) If "*ppos" is non-zero then the first part of the dump_data
   buffer is uninitialized.  Using copy_from_user() instead of
   simple_write_to_buffer() is more appropriate here.

Fixes: d5d5df6da0aa ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Remove extra line setting the broadcast code parameter of the
hci_cp_le_create_big struct to 0. The broadcast code is copied
from the QoS struct.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Fixed a wrong indentation before "return".This line uses a 7 space
indent instead of a tab.
Signed-off-by: Lanzhe Li <u202212060@hust.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

We can never assume the uart will deliver a complete packet to the BT
layer at once, the expected packet may be divided into several parts by
uart as uart doesn't know the received packet size, the received data
count may mismatch with the expected packet size, so here
is_valid_bootloader_signature() check may always return false.

Even we remove the count check in is_valid_bootloader_signature(), then
the first part of the data which includes the packet type can pass the
is_valid_bootloader_signature() check, but the remaining parts don't
have the packet type data still cannot pass the check, here return
directly will cause the data loss.

So need to remove the received bootloader signature check here, the
h4_recv_buf() can help us combine the different data received into one
packet. If any out-of-sync or incomplete bootloader signature is received,
it is safe to ignore and discard it, and process the next bootloader
signature.
Co-developed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This sets the default power save mode setting to disabled.
With this setting, this driver will behave like a normal h4 driver.
If user needs to use the power save feature, it can be enabled
using the following vendor command:
hcitool cmd 3f 23 02 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds a call to ps_wakeup() before closing the serdev device, to
de-assert UART break.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds support to download helper FW file for the legacy NXP chipset
88w8997 for the btnxpuart driver. This helper FW file is necessary to
set the bootloader baudrate to 3000000 after which the actual BT FW file
can be downloaded. This change helps bring the FW download time from
around 10 sec to less than 2 sec for 88w8997 chip. For newer chipsets,
both V1 and V3 bootloader, driver sends the cmd5 and cmd7 to the chip
bootloader, and does not need a helper FW file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The DSDT for the Acer Iconia One 7 B1-750 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.

Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.

Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The DSDT for the Lenovo Yoga Tablet 2 830 / 1050 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.

Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.

Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The bcm43430a0 and bcm43430a1 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and it also does not work at 4000000
baud without this command as some newer models do.

These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at 4000000, which does
not work.

Add a max_baudrate value to struct bcm_device_data and set this
to 2000000 on all known ACPI hardware-ids for the bcm43430a0
and the bcm43430a1.

Note this also adds the BCM2E9F ACPI HID which was missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.

btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:

btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'

Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.

But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.

Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.

This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

As shown in the schematic diagram below.There may be a critical
scenario in the current code. If the device does not receive an
pure ack sent by the host due to insufficient receive buffer or
other reasons and triggers a retransmission, the host will always
be in an 'out-of-order' state.The state machine will get stuck.

       host                 device
     SEQ3,ACK4 --------->
               <--------- SEQ4,ACK4
     pure ACK  ---------> (not received)
(out-of-order) <--------- SEQ4,ACK4(retransmission)
                ........
(out-of-order) <--------- SEQ4,ACK4(retransmission)

According to the description in the core specification: "whenever
a reliable packet is received, an acknowledgment shall be generated."
So set H5_TX_ACK_REQ bit to trigger retransmission of pure ack packet
when "out-of-order" occurs.
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This enables 2M and Coded PHY by default if they are marked as supported
in the LE features bits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Split bt_iso_qos into dedicated unicast and broadcast
structures and add additional broadcast parameters.

Fixes: eca0ae4a ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Intercept debug exception events from the controller and put them into
a devcoredump using hci devcoredump APIs. The debug exception contains
data in a TLV format and it will be parsed in userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This patch implements the btusb driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add devcoredump support for vhci that creates forcce_devcoredump debugfs
entry. This is used for mgmt-tester tests.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add devcoredump APIs to hci core so that drivers only have to provide
the dump skbs instead of managing the synchronization and timeouts.

The devcoredump APIs should be used in the following manner:
 - hci_devcoredump_init is called to allocate the dump.
 - hci_devcoredump_append is called to append any skbs with dump data
   OR hci_devcoredump_append_pattern is called to insert a pattern.
 - hci_devcoredump_complete is called when all dump packets have been
   sent OR hci_devcoredump_abort is called to indicate an error and
   cancel an ongoing dump collection.

The high level APIs just prepare some skbs with the appropriate data and
queue it for the dump to process. Packets part of the crashdump can be
intercepted in the driver in interrupt context and forwarded directly to
the devcoredump APIs.

Internally, there are 5 states for the dump: idle, active, complete,
abort and timeout. A devcoredump will only be in active state after it
has been initialized. Once active, it accepts data to be appended,
patterns to be inserted (i.e. memset) and a completion event or an abort
event to generate a devcoredump. The timeout is initialized at the same
time the dump is initialized (defaulting to 10s) and will be cleared
either when the timeout occurs or the dump is complete or aborted.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Basically all Intel controllers support both Central/Peripheral
LE states.

This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.

Based on the assumption that this is similar to the wcn6750

Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add bindings for the QTI WCN6855 chipset.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since
b8e482d02513. However, if installing a Realtek Bluetooth controller
without the driver supported, it will hit the NULL point accessed.

Add a check for NULL to avoid the Kernel Oops.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This device is part of a Realtek RTW8852BE chip. The device table is as follows:

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3571 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This device is part of a Realtek RTW8852BE chip.

The device table entry is as follows:

T:  Bus=03 Lev=01 Prnt=01 Port=12 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=887b Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver needs both CRC32 and CRC8 to link correctly:

ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe':
drivers/bluetooth/btnxpuart.c:1214: undefined reference to
`crc8_populate_msb'
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack':
drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'

Fixes: 3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds a driver based on serdev driver for the NXP BT serial protocol
based on running H:4, which can enable the built-in Bluetooth device
inside an NXP BT chip.

This driver has Power Save feature that will put the chip into sleep state
whenever there is no activity for 2000ms, and will be woken up when any
activity is to be initiated over UART.

This driver enables the power save feature by default by sending the vendor
specific commands to the chip during setup.

During setup, the driver checks if a FW is already running on the chip
by waiting for the bootloader signature, and downloads device specific FW
file into the chip over UART if bootloader signature is received..
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add binding document for NXP bluetooth chipsets attached over UART.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Adds serdev_device_break_ctl() and an implementation for ttyport.
This function simply calls the break_ctl in tty layer, which can
assert a break signal over UART-TX line, if the tty and the
underlying platform and UART peripheral supports this operation.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This replaces all instances of ENOTSUPP with EOPNOTSUPP since ENOTSUPP
is not a standard error code. This will help maintain consistency in
error codes when new serdev API's are added.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

tty_set_termios() never returns anything else than 0. Make the debug
prints to look directly into the new termios instead to check CRTSCTS
state.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add two more quirks to resume the device initialization and basic
operation as the device seems not to support "Read Transmit Power"
and "Set Extended Scan Parameters".

< HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0
> HCI Event: Command Status (0x0f) plen 4
      LE Read Transmit Power (0x08|0x004b) ncmd 1
        Status: Unknown HCI Command (0x01)

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Status (0x0f) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Unknown HCI Command (0x01)
Signed-off-by: Raul Cheleguini <rcheleguini@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.

It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.

Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined
  but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined
  but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined
  but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
  defined but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
  defined but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
  defined but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
  defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/bluetooth/btmrvl_sdio.c:43:34: error:
  ‘btmrvl_sdio_of_match_table’ defined but not used
  [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).

  drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined
  but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This delays the identity address updates to give time for userspace to
process the new address otherwise there is a risk that userspace
creates a duplicated device if the MGMT event is delayed for some
reason.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This removes the following duplicate statement in
hci_le_ext_directed_advertising_sync():
cp.own_addr_type = own_addr_type;
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>