Currently the ad7606 driver uses a value of 0 for the oversampling ratio to
express that no oversampling is done. Strictly speaking this means though
that no data capture is done at all. Instead change the driver to use a
value of 1, this is in accordance with what other drivers do and what the
IIO spec suggests.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Currently the ad7606 driver prints a error message to the kernel log when
an application writes an invalid value to a sysfs attribute. While for
initial driver development and testing this might be useful it is quite
disadvantageous in a production environment. The write() call to the sysfs
attribute will already return an error if the value was invalid so the
application is aware that the operation failed. And generally speaking it
is impossible for an application to reliably match a log message in the
kernel log to a specific operation it performed, so the message becomes
just noise and might distract from more critical messages.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

While for some very selected setups it might be useful to be able to
provide default configuration data via the platform data, generally this
becomes very impractical as the number of configuration options increases.
So the general policy is to use the power-on default values of the device
and let the application using the device configure it according to its
needs.

Implement this scheme for the ad7606 driver by removing support for
specifying a default configuration via the platform data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The name field in the ad7606_chip_info struct is set to the same value as
the as the name field in the corresponding {platform,spi}_device_id table
entry. Remove it from the ad7606_chip_info struct and pass the name from
the ID to the probe function. This slightly reduces the size of the
chip_info table and adding new entries requires less boilerplate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove the int_vref_mv field from the ad7606_chip_info struct since the
field is never used by the driver. The value is also the same for all
derivatives of this chip, so if it will ever be used in the driver a
constant value will work just fine.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove extra parentheses introduced in commit <73e176a tools: iio:
iio_generic_buffer: add -A to force-enable all channels>.
Suggested-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Replace the type of 'force' flag from int to bool and at the same time
rename it to 'force_autochannels' for better readability.
Suggested-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add support to STM HTS221 humidity + temperature sensor

http://www.st.com/resource/en/datasheet/hts221.pdf

- continuous mode support
- i2c support
- spi support
- trigger mode support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during all raw write operations.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during required raw read cases.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Now the driver is in a reasonable state, lets get it (finally) out
of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Basic tidy up of comments to bring them into a standard style.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Tidied up where checkpatch warning suppressions doesn't effect the
readability of the code.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Previously the device was exposed to userspace and in kernel consumers
before the interrupts had been configured. As nothing stopped them being
enabled in the interval this could cause unhandled interrupts.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

There seems little point in being able to query the part revision number
via sysfs.  Hence just put it in the kernel logs during probe incase
anyone ever wants to know.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

This is now represented by the standard 3db filter frequency controls.
Things get complex wrt to the sampling frequency as these modes change
but that is fine under the IIO ABI where any value is allowed to effect
any other.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Also includes an available attribute.  The ordering of values appears
a bit random, but as the ABI doesn't specify this and we already have
both rising and falling lists I think this is fine.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Given the introduction of IIO_NO_MOD was prior to the first submission
prior to IIO entering staging this has been broken for a while.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Driving towards getting rid of the non standard mode control interface.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Introduce some more masks and generally drive towards consistent naming.
Note the small indents used to indicate parts of registers + parts of
multiplexed registers.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

This is an approach used in some newer drivers as it exposes the
compound channel events to the core rather than hiding their control
in sysfs attributes entirely via the driver.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

In a similar fashion to other newer drivers (e.g. ti_am335x), instead
of using the hardware buffer support in IIO to directly access the hardware
fifo, insert a software fifo and feed that from the hardware one when
interrupts occur.  This gives a simpler structure to the data flows and
allows more flexibility over how often data is shipped to userspace etc.

This was also the only direct user of the simplistic generalization found
in ring_hw.h so that header is removed.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

For now we support only the 50% watershed interrupt and start and stop it
as part of the buffer bring up.  The 75% case may come back in future.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Not clearing the stuff_to_read flag can lead to a false flag being set
on restarting the buffer if the data was not all read the previous time.

The size of the scan is needed to ensure the function
iio_buffer_read_first_n_outer actually tries to read the data.

This stuff has been broken for some time so not stable material.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

This was needed when the buffer support was optional. Pointless wrapper
now so drop it.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

In the early days of IIO we were much more inclined to keep the impact
of the core IIO elements to the minimum.  As time has moved on it has
become clear that hardly any builds are done without buffer support
and that it adds considerable complexity to the drivers.

Hence merge down the buffer and non buffer elements of the sca3000 driver
also allowing us to drop the header file used for the interfaces between
the two.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>

Move ISL29018/ISL29023/ISL29035 driver out of staging into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add ABI documentation from the ISL29018 Data Sheet (FN6619.4, Oct 8,
2012) about the infrared suppression that can be controlled
with the proximity_on_chip_ambient_infrared_suppression sysfs attribute.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during all write raw operations.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

If attribute/s is/are already enabled (by default or via scripts or
manual interaction), issuing -a will fail to enable the channels thereby
one has to manually disable the said attribute/s before proceeding with
auto-enabling.

Add a command-line option -A to force-activate all channels regardless
of their current state.
Suggested-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Use a standard framework to get the reference voltage. It is done that way
in the iio subsystem and it will simplify extending of the driver.

Structure mcp4725_platform_data is left undeleted because it used in the
next patch.

This change breaks the current users of the driver, but there is no
mainline user of struct mcp4725_platform_data.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Change in handling of the regulator description means that static
checkers correctly assume we could be using dereferenced pointer to the
regulator. In reality we will never get the -ENODEV error, as current
behavior flow does not predict it, because:
If the device tree or board file does not define suitable regulators for
the component, it will be substituted by a dummy regulator, or, if
regulators are disabled altogether, by stubs.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The "drivers/" part of the path name was missing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

There is a type mismatch between the buffer which is of type s16 and the
samples stored, which are declared as __le16.

Fix the following sparse warning:
drivers/iio/imu/bmi160/bmi160_core.c:411:26: warning: incorrect type
in assignment (different base types)

drivers/iio/imu/bmi160/bmi160_core.c:411:26: expected signed short
[signed] [short] [explicitly-signed] <noident>
drivers/iio/imu/bmi160/bmi160_core.c:411:26: got restricted __le16
[addressable] [usertype] sample

This is a cosmetic-type patch since it does not alter code behaviour.
The le16 is going into a 16bit buf element, and is labelled as IIO_LE in the
channel buffer definition.
Signed-off-by: sayli karnik <karniksayli1995@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Rename description from "ISL 29018" to "Intersil 29018" in Kconfig for
consistency with other drivers in mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>