We need to store cmlen instead of len in cm->cmsg_len.

Fixes: 38ebcf50 ("scm: optimize put_cmsg()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
ethtool: add standard FEC statistics

This set adds uAPI for reporting standard FEC statistics, and
implements it in a handful of drivers.

The statistics are taken from the IEEE standard, with one
extra seemingly popular but not standard statistics added.

The implementation is similar to that of the pause frame
statistics, user requests the stats by setting a bit
(ETHTOOL_FLAG_STATS) in the common ethtool header of
ETHTOOL_MSG_FEC_GET.

Since standard defines the statistics per lane what's
reported is both total and per-lane counters:

 # ethtool -I --show-fec eth0
 FEC parameters for eth0:
 Configured FEC encodings: None
 Active FEC encoding: None
 Statistics:
  corrected_blocks: 256
    Lane 0: 255
    Lane 1: 1
  uncorrectable_blocks: 145
    Lane 0: 128
    Lane 1: 17

v2: check for errors in mlx5 register access
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Report corrected bits.

v2: catch reg access errors (Saeed)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report what appears to be the standard block counts:
 - 30.5.1.1.17 aFECCorrectedBlocks
 - 30.5.1.1.18 aFECUncorrectableBlocks

Don't report the per-lane symbol counts, if those really
count symbols they are not what the standard calls for
(even if symbols seem like the most useful thing to count.)

Fingers crossed that fec_corrected_errors is not in symbols.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report corrected bits.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similarly to pause statistics add stats for FEC.

The IEEE standard mandates two sets of counters:
 - 30.5.1.1.17 aFECCorrectedBlocks
 - 30.5.1.1.18 aFECUncorrectableBlocks
where block is a block of bits FEC operates on.
Each of these counters is defined per lane (PCS instance).

Multiple vendors provide number of corrected _bits_ rather
than/as well as blocks.

This set adds the 2 standard-based block counters and a extra
one for corrected bits.

Counters are exposed to user space via netlink in new attributes.
Each attribute carries an array of u64s, first element is
the total count, and the following ones are a per-lane break down.

Much like with pause stats the operation will not fail when driver
does not implement the get_fec_stats callback (nor can the driver
fail the operation by returning an error). If stats can't be
reported the relevant attributes will be empty.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor fec_prepare_data() a little bit to skip the body
of the function and exit on error. Currently the code
depends on the fact that we only have one call which
may fail between ethnl_ops_begin() and ethnl_ops_complete()
and simply saves the error code. This will get hairy with
the stats also being queried.

No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'll need it for FEC stats as well.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling two copy_to_user() for very small regions has very high overhead.

Switch to inlined unsafe_put_user() to save one stac/clac sequence,
and avoid copy_to_user().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert system_wq queue_work() to schedule_work() which is
a wrapper around it, since the former is a rare construct.

Fixes: 7294380c ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: updates for -next

This series adds support for pushing link status to VFs for
the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.

To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
in the chip configure register.

The driver assumes the copper side is selected on probe, but this might
not be the case depending which page was last selected by the
bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.

Select the copper page when probing to circumvent this.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-04-14

This series contains updates to ice driver only.

Bruce changes and removes open coded values to instead use existing
kernel defines and suppresses false cppcheck issues.

Ani adds new VSI states to track netdev allocation and registration. He
also removes leading underscores in the ice_pf_state enum.

Jesse refactors ITR by introducing helpers to reduce duplicated code and
structures to simplify checking of ITR mode. He also triggers a software
interrupt when exiting napi poll or busy-poll to ensure all work is
processed. Modifies /proc/iomem to display driver name instead of PCI
address. He also changes the checks of vsi->type to use a local variable
in ice_vsi_rebuild() and removes an unneeded struct member.

Jake replaces the driver's adaptive interrupt moderation algorithm to
use the kernel's DIM library implementation.

Scott reworks module reads to reduce the number of reads needed and
remove excessive increment of QSFP page.

Brett sets the vsi->vf_id to invalid for non-VF VSIs.

Paul removes the return value from ice_vsi_manage_rss_lut() as it's not
communicating anything critical. He also reduces the scope of a
variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF.  Mostly this struct member was unused.

Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.

It's more useful for debugging to see the driver name, as
most other modules do.

Here's a diff of before and after this change:
     99100000-991fffff : 0000:3b:00.1
   9a000000-a04fffff : PCI Bus 0000:3b
     9a000000-9bffffff : 0000:3b:00.1
-      9a000000-9bffffff : 0000:3b:00.1
+      9a000000-9bffffff : ice
     9c000000-9dffffff : 0000:3b:00.0
-      9c000000-9dffffff : 0000:3b:00.0
+      9c000000-9dffffff : ice
     9e000000-9effffff : 0000:3b:00.1
     9f000000-9fffffff : 0000:3b:00.0
     a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.

Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.

Basically unpack the "high bit means dynamic" logic
into bitfields.

Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.

Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.

This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.

The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.

The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.

The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).

There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.

The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them.  This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.

In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files.  Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge tag 'linux-can-next-for-5.13-20210414' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2021-04-14

this is a pull request of a single patch for net-next/master.

Vincent Mailhol's patch fixes a NULL pointer dereference when handling
error frames in the etas_es58x driver, which has been added in the
previous PR.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

af_packet fanout uses RCU rules to ensure f->arr elements
are not dismantled before RCU grace period.

However, it lacks rcu accessors to make sure KCSAN and other tools
wont detect data races. Stupid compilers could also play games.

Fixes: dc99f600 ("packet: Add fanout support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Ethernet switches might only be able to support disabling multicast
snooping globally, which is an issue for example when several bridges
span the same physical device and request contradictory settings.

Propagate the return value of br_mc_disabled_update() such that this
limitation is transmitted correctly to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2021-04-13

mlx5 core and netdev driver updates

1) E-Switch updates from Parav,
  1.1) Devlink parameter to control mlx5 metadata enablement for E-Switch
  1.2) Trivial cleanups for E-Switch code
  1.3) Dynamically allocate vport steering namespaces only when required

2) From Jianbo, Use variably sized data structures for Software steering

3) Several minor cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Normally, the bootloader will already initialize the MAC address
registers of the ENETC and the driver will just use them or generate a
random one, if it is not initialized.

Add a new way to provide the MAC address: via device tree. Besides the
usual 'mac-address' property, there is also the possibility to fetch it
via a NVMEM provider. The sl28 board stores the MAC address in the SPI
NOR flash OTP region. Having this will allow linux to fetch the MAC
address from there without being dependent on the bootloader.

No in-tree boards have the device tree properties set, thus for these,
this is a no-op.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following coccicheck warning:

./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to |
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the commit 1ddc3229 ("skbuff: remove some unnecessary operation
in skb_segment_list()") introduces an issue very similar to the
one already fixed by commit 53475c5d ("net: fix use-after-free when
UDP GRO with shared fraglist").

If the GSO skb goes though skb_clone() and pskb_expand_head() before
entering skb_segment_list(), the latter  will unshare the frag_list
skbs and will release the old list. With the reverted commit in place,
when skb_segment_list() completes, skb->next points to the just
released list, and later on the kernel will hit UaF.

Note that since commit e0e3070a ("udp: properly complete L4 GRO
over UDP tunnel packet") the critical scenario can be reproduced also
receiving UDP over vxlan traffic with:

NIC (NETIF_F_GRO_FRAGLIST enabled) -> vxlan -> UDP sink

Attaching a packet socket to the NIC will cause skb_clone() and the
tunnel decapsulation will call pskb_expand_head().

Fixes: 1ddc3229 ("skbuff: remove some unnecessary operation in skb_segment_list()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following clang warning:

drivers/atm/idt77252.c:1787:1: warning: unused function
'idt77252_fbq_level' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2021-04-14

Not much this time:

1) Simplification of some variable calculations in esp4 and esp6.
   From Jiapeng Chong and Junlin Yang.

2) Fix a clang Wformat warning in esp6 and ah6.
   From Arnd Bergmann.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for the [g|s]et_pauseparam ethtool ops. It considers
that the chip doesn't support pause frame use in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>