Implement polling with 10 ms timeout for automatic pad drive strength
calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Parse the pinctrl state and nvidia,only-1-8-v properties from the device
tree. Validate the pinctrl and regulator configuration before unmasking
UHS modes. Implement pad voltage state reconfiguration in the mmc
start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
and add set it for Tegra210 and Tegra186.

The pad configuration is done in the mmc callback because the order of
pad reconfiguration and sdhci voltage switch depend on the voltage to
which the transition occurs.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document the Tegra SDHCI inbound and outbound sampling trimmer values.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add bindings documentation for pad pull up and pull down offset values to be
programmed before executing automatic pad drive strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document the pinctrl bindings used by the SDHCI driver to reconfigure
pad voltages on controllers supporting multiple voltage levels.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This variable is unused now after some refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Concise, but still readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDR104, HS200 and HS400 need to check for SCC error. If SCC error is
detected, retuning is necessary.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Checking for SCC error during retuning is unnecessary.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: fix small style issue]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a helper to allow host drivers checking if a retune is in progress.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

for (clk = 0x80000080; new_clock >= (clock << 1); clk >>= 1)
          clock <<= 1;

... is too tricky, hence I replaced with

  roundup_pow_of_two(divisor) >> 2

'(clk >> 22) & 0x1' is the bit test for the 1/1 divisor, but
it is not clear.  'divisor <= 1' is easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

renesas_sdhi_clk_start() and renesas_sdhi_clk_stop() are now only
called from renesas_sdhi_set_clock().  Merge them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When using DMA, if the DMA addr spans 128MB boundary, we have to split
the DMA transfer into two so that each one doesn't exceed the boundary.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds adma_table_cnt member to struct sdhci_host to give more
flexibility to drivers to control the ADMA table count.

Default value of adma_table_cnt is set to (SDHCI_MAX_SEGS * 2 + 1).
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Allow SDHCI drivers to hook code before and after sdhci_request() by
making it externally visible.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

After host requests RESET_FOR_ALL action, the hardware output an
interrupt for OS and waiting for the OS to approve.

Before writing this fix, ACPI GED has handled the interrupt. But
the ACPI GED belongs to a slow process, and sometimes the handling
process time is more than 100ms(Mutex wait more than 100ms). So
drop the GED solution and add this quirk fix.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In tuning mode of operation, when TBCTL[TB_EN] is set, eSDHC may report
one of the following errors :
1)Tuning error while running tuning operation where SYSCTL2[SAMPCLKSEL]
will not get set even when SYSCTL2[EXTN] is reset. OR
2)Data transaction error (e.g. IRQSTAT[DCE], IRQSTAT[DEBE]) during data
transaction errors.
This issue occurs when the data window sampled within eSDHC is in full
cycle. So, in that case, eSDHC is not able to find out the start and
end points of the data window and sets the sampling pointer at default
location (which is middle of the internal SD clock). If this sampling
point coincides with the data eye boundary, then it can result in the
above mentioned errors. Impact: Tuning mode of operation for SDR50,
SDR104 or HS200 speed modes may not work properly
Workaround: In case eSDHC reports tuning error or data errors in tuning
mode of operation, by add the erratum A008171 support to fix the issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch is to add tuning error codes to
judge tuning state
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Here is another TMIO MMC variant found in Socionext UniPhier SoCs.

As commit b6147490 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.

However, the MMC controller in the TMIO (Toshiba Mobile IO) MFD chip
was the first upstreamed user of this IP.  The common driver code
for this IP is now called 'tmio-mmc-core' in Linux although it is a
historical misnomer.

Anyway, this driver select's MMC_TMIO_CORE to borrow the common code
from tmio-mmc-core.c

Older UniPhier SoCs (LD4, Pro4, sLD8) support the external DMA engine
like renesas_sdhi_sys_dmac.c.  The difference is UniPhier SoCs use a
single DMA channel whereas Renesas chips request separate channels for
RX and TX.

Newer UniPhier SoCs (Pro5 and later) support the internal DMA engine
like renesas_sdhi_internal_dmac.c  The register map is almost the same,
so I guess Renesas and Socionext use the same internal DMA hardware.
The main difference is, the register offsets are doubled for Renesas.

                        Renesas      Socionext
                        SDHI         UniPhier
  DM_CM_DTRAN_MODE      0x820        0x410
  DM_CM_DTRAN_CTRL      0x828        0x414
  DM_CM_RST             0x830        0x418
  DM_CM_INFO1           0x840        0x420
  DM_CM_INFO1_MASK      0x848        0x424
  DM_CM_INFO2           0x850        0x428
  DM_CM_INFO2_MASK      0x858        0x42c
  DM_DTRAN_ADDR         0x880        0x440
  DM_DTRAN_ADDREX        ---         0x444

This comes from the difference of host->bus_shift; 2 for Renesas SoCs,
and 1 for UniPhier SoCs.  Also, the datasheet for UniPhier SoCs defines
DM_DTRAN_ADDR and DM_DTRAN_ADDREX as two separate registers.

It could be possible to factor out the DMA common code by introducing
some hooks to cope with platform quirks, but this patch does not touch
that for now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This SD/eMMC controller is used for UniPhier SoC family.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.

The original IP defines the divisor range 1/2 ... 1/512.

 bit 7 is set:    1/512
 bit 6 is set:    1/256
   ...
 bit 0 is set:    1/4
 all bits clear:  1/2

It is platform-dependent how to achieve the 1/1 clock.

I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c

I guess bit[7:0]=0xff is Renesas-specific extension.

Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1.  Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.

host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.

To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

tmio_mmc_clk_stop(host) is equivalent to tmio_mmc_set_clock(host, 0).
This replacement is needed for the next commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The JZ4725B is the first JZ SoC version that introduced a 32-bit IMASK
register, not the JZ4750.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document the R-Car V3M (R8A77970) SoC in the R-Car SDHI bindings -- it's
the usual R-Car gen3 compatible controller with the internal DMA engine.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

I've successfully tested eMMC on the V3H Starter Kit board and since the
R8A77970 SoC has a single SDHI core, it can't be a subject to the known RX
DMA errata.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

Remove the stray underscore in the DM_CM_DTRAN_MODE.BUS_WIDTH register
field name and fix the typo in the comment of the #define
DTRAN_MODE_CH_NUM_CH1.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Depending on MACH_JZ4740 | MACH_JZ4780 prevent us from creating a generic
kernel that works on more than one MIPS board. Instead, we just depend on
MIPS being set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Enable access to the RPMB on the on-board eMMC of the
Poplar board.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We need r8a774a1 to be whitelisted for SDHI to work on the RZ/G2M,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add ACPI support to all IPROC SDHCI variants.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Convert DT properties to generic device properties
so that drivers can get properties from DT or ACPI.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

I wrote:
  "Char/Misc fixes for 4.19-rc7

   Here are 8 small fixes for some char/misc driver issues

   Included here are:
	- fpga driver fixes
	- thunderbolt bugfixes
	- firmware core revert/fix
	- hv core fix
	- hv tool fix

   All of these have been in linux-next with no reported issues."

* tag 'char-misc-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  thunderbolt: Initialize after IOMMUs
  thunderbolt: Do not handle ICM events after domain is stopped
  firmware: Always initialize the fw_priv list object
  docs: fpga: document fpga manager flags
  fpga: bridge: fix obvious function documentation error
  tools: hv: fcopy: set 'error' in case an unknown operation was requested
  fpga: do not access region struct after fpga_region_unregister
  Drivers: hv: vmbus: Use get/put_cpu() in vmbus_connect()

I wrote:
  "Serial driver fixes for 4.19-rc7

   Here are 3 small serial driver fixes for 4.19-rc7
    - 2 sh-sci bugfixes for reported issues
    - a revert of the PM handling for the 8250_dw code

   All of these have been in linux-next with no reported issues."

* tag 'tty-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: sh-sci: Allow for compressed SCIF address"
  Revert "serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE"
  Revert "serial: 8250_dw: Fix runtime PM handling"