- 17 Mar, 2014 39 commits
-
-
Vladimir Kondratiev authored
New firmware do support scan while connected. Enable it. Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
When connection established, as reported by WMI_CONNECT_EVENTID, 4-way handshaking required for the secure connection is not done yet. It is indicated by another WMI event. Wait for it and only then allow data traffic. In case of non-secure connection, FW reports "data port open" immediately after connection. Signed-off-by:
-
Vladimir Kondratiev authored
Encode/decode helpers Signed-off-by:
-
Sujith Manoharan authored
The registers for temperature compensation need to be programmed only for active chains. Use the TX chainmask to make sure that this is done properly for QCA953x. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
Along with AR9340 and AR955x, this is also needed for the QCA953x SoC. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Andrea Merello authored
Eeprom read operations are mixed in the probe function. Make the code more readable and clean by extracting this code and moving it in a dedicated function. The variable eeprom_cck_table_adr, now useless, is here because it will be needed for rtl8187se support, that I hope to add soon. Signed-off-by:
Andrea Merello <andrea.merello@gmail.com> Signed-off-by:
-
Andrea Merello authored
SLOT, SIFS, DIFS, EIFS, CW and ACK-timeout registers are set in an RF-code callback and their values are fixed. This patch moves this off the rf-code, and introduce two new functions that calculate these values depending by slot time and CW values requested by mac80211. This seems to improve performances on my setup. Currently the ack and slot time values could be stored in a local variable, but this patch stores it in the driver "priv" structure because it will be useful for rtl8187se support that will be added (hopefully) soon. Signed-off-by:
-
Andrea Merello authored
Basic rates setting is done with hardcoded register write with fixed settings. This patch introduces a new function that makes it possible to configure basic rates and it add a check for mac80211 BSS_CHANGED_BASIC_RATES flag in order to eventually invoke that function when needed. Signed-off-by:
-
Andrea Merello authored
While changing board-type variable to enum, I have added enum value for rtl8187se by mistake. This will causes gcc warnings with unhandled switch/cases. Remove it temporarily until I will push also rtl8187se changes. Signed-off-by:
-
Arend van Spriel authored
The nl80211 iftype was converted to a mode value and stored in brcmf_cfg80211_vif structure. The value was used only within brcmfmac driver to decide execution of conditional code. Better use wireless_dev::iftype for that as the wdev is contained in the brcmf_cfg80211_vif structure. Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
When the SDIO driver goes in low power state it must assure that a clock request in ChipCLKCSR is set. Otherwise waking up the device can fail. The register is read and if necessary the ALP clock will be requested. Reviewed-by:
-
Hante Meuleman authored
When connecting without specifying the channel it can take quite some time to connect. This is because not all parameters for the scan operation are set to optimized values. This patch changes these parameters resulting in a much faster connect in certain situations. Reviewed-by:
-
Hante Meuleman authored
SDIO tx uses a sequence number which is common for data and control. This requires that access to this sequence number is protected. A mutex was used to achieve this, but it also required the reordering of code for tx control. Reviewed-by:
-
Franky Lin authored
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through SDIO interface. Reviewed-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-nextJohn W. Linville authored
Samuel Ortiz <sameo@linux.intel.com> says: "NFC: 3.15: First pull request This is the NFC pull request for 3.15. With this one we have: - Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO 15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel now supports those through the NFC netlink and digital APIs. - Support for TI's trf7970a chipset. This chipset relies on the NFC digital layer and the driver currently supports type 2, 4A and 5 tags. - Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets relies on a different firmware download protocal than the C2 one. We now support both and use the right one depending on the version we detect at runtime. - Support for 4A tags from the NFC digital layer. - A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande." Signed-off-by: -
Oleksij Rempel authored
... to remove some more dups. Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
we will need it for common-beacon Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
we will need it to make common-beacon code work. Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
we will need it for ath9k_htc, may be other drivers too Signed-off-by:
-
Oleksij Rempel authored
to reduce difference between ath9k and ath9k_htc Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
- 14 Mar, 2014 1 commit
-
-
Axel Lin authored
nfc_llcp_find_local() does not modify any list entry while iterating the list. So use list_for_each_entry instead of list_for_each_entry_safe. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com>
-
