o Minimum fw version supported for P3 chip is 4.0.505
o File Fw > 4.0.554 is not supported if flash fw < 4.0.554.
o In mn firmware case, file fw older than flash fw is allowed.
o Change variable names for readability
o Update driver version 4.0.76
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently be3-native mode is requested only in probe(). It must be requested, each time the card is reset either after an EEH error or after
sleep/hibernation.
Also, the be_cmd_check_native_mode() is better named be_cmd_req_native_mode()
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the ip fragment offset field counts 8-byte chunks, ip
fragments other than the last must contain a multiple of 8 bytes of
payload.  ip_ufo_append_data wasn't respecting this constraint and,
depending on the MTU and ip option sizes, could create malformed
non-final fragments.

Google-Bug-Id: 5009328
Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a panic in virtnet_remove. unregister_netdev has already
freed up the netdev (and virtnet_info) due to dev->destructor
being set, while virtnet_info is still required. Remove
virtnet_free altogether, and move the freeing of the per-cpu
statistics from virtnet_free to virtnet_remove.

Tested patch below.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 fragment identification generation is way beyond what we use for
IPv4 : It uses a single generator. Its not scalable and allows DOS
attacks.

Now inetpeer is IPv6 aware, we can use it to provide a more secure and
scalable frag ident generator (per destination, instead of system wide)

This patch :
1) defines a new secure_ipv6_id() helper
2) extends inet_getid() to provide 32bit results
3) extends ipv6_select_ident() with a new dest parameter
Reported-by: Fernando Gont <fernando@gont.com.ar>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently cow metrics a bit too soon in IPv6 case : All routes are
tied to a single inetpeer entry.

Change ip6_rt_copy() to get destination address as second argument, so
that we fill rt6i_dst before the dst_copy_metrics() call.

icmp6_dst_alloc() must set rt6i_dst before calling dst_metric_set(), or
else the cow is done while rt6i_dst is still NULL.

If orig route points to readonly metrics, we can share the pointer
instead of performing the memory allocation and copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function can_get_bittiming is not used anywhere else, so it should be
static.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kobj and queues_kset are used with CONFIG_XPS=y.
Signed-off-by: Choi, Jong-Hwan <jhbird.choi@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NETIF_F_HIGHDMA is being disabled even when dma64 is true. This patch fixes it.

CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parent device for netdev should be set before netdev_info() can be called
otherwise there is a NULL pointer dereference and probe() fails.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>

This device can be found in Acer Iconia TAB W500 tablet dock.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds new information for the driver
especially about its platform structure fields.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to this change, most PHY configuration parameters were passed
into the STMMAC device as a separate PHY device. As well as being
unusual, this made it difficult to make changes to the MAC/PHY
relationship.

This patch moves all the PHY parameters into the MAC configuration
structure, mainly as a separate structure. This allows us to completely
ignore the MDIO bus attached to a stmmac if desired, and not create
the PHY bus. It also allows the stmmac driver to use a different PHY
from the one it is connected to, for example a fixed PHY or bit banging
PHY.

Also derive the stmmac/PHY connection type (MII/RMII etc) from the
mode can be passed into <platf>_configure_ethernet.
STLinux kernel at git://git.stlinux.com/stm/linux-sh4-2.6.32.y.git
provides several examples how to use this new infrastructure (that
actually is easier to maintain and clearer).
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch removes the following serie of warnings
when the driver is compiled as built-in:

drivers/net/stmmac/stmmac_main.c: In function stmmac_cmdline_opt:
drivers/net/stmmac/stmmac_main.c:1855:12: warning: ignoring return
value of kstrtoul, declared with attribute warn_unused_result
[snip]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some drivers (ab)use the ethtool_ops::get_regs operation to expose
only a hardware revision ID.  Commit
a77f5db3 ('ethtool: Allocate register
dump buffer with vmalloc()') had the side-effect of breaking these, as
vmalloc() returns a null pointer for size=0 whereas kmalloc() did not.

For backward-compatibility, allow zero-length dumps again.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org [2.6.37+]
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add the missing dma_unmap().
Which solved the critical issue of system freeze on heavy load.

Michal Miroslaw's rejected patch:
[PATCH v2 10/46] net: jme: convert to generic DMA API
Pointed out the issue also, thank you Michal.
But the fix was incorrect. It would unmap needed address
when low memory.

Got lots of feedback from End user and Gentoo Bugzilla.
https://bugs.gentoo.org/show_bug.cgi?id=373109
Thank you all. :)

Cc: stable@kernel.org
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two problems:
1) "n" was allocated with alloc_skb() so we should free it with
   kfree_skb() instead of regular kfree().
2) We return the freed pointer instead of NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

there are no users outside vlan code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

has no users so remove it
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndo_vlan_rx_register is no longer in use in any driver so remove it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when all devices are cleaned up, bond can be cleaned up as well

- remove bond->vlgrp
- remove bond_vlan_rx_register
- substitute necessary occurences of vlan_group_get_device
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- kill priv->vlgrp and stmmac_vlan_rx_register (used for nothing :))
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill card->vlangrp and qeth_l3_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill vdev->vlgrp and vxge_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill adapter->vlgrp and igb_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill np->vlangrp and nv_vlan_rx_register
- allow to turn on/off rx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill adapter->vlgrp and e1000_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill pi->vlan_grp and vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl2_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atlx_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill dev->vlgrp and ns83820_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill np->vlgrp and netdev_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill vptr->vlgrp and velocity_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill ap->vlgrp and ace_vlan_rx_register
- enable vlan hw accel always (kill vlan ifdefs)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>