This patch adds the support of the rx/tx errors CAN counters to the
driver of the PCAN-USB PC-CAN interface from PEAK-System GmbH.

The PCAN-USB is capable of giving back the values of the rx/tx errors
counters, to provide more details and statistics to the linux-can layer.
Getting these values allows the driver to better tune CAN_ERR_CRTL_TX_xxx
and CAN_ERR_CRTL_RX_xxx bits in case of the interface enters any
CAN_STATE_ERROR_xxx state.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20191206153803.17725-3-s.grosjean@peak-system.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch documents the functions and numbers of the commands sent by the
driver to the PCAN-USB CAN device from PEAK-System GmbH.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20191206153803.17725-2-s.grosjean@peak-system.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Drivers using legacy power management .suspen()/.resume() callbacks have to
manage PCI states and device's PM states themselves. They also need to take
care of standard configuration registers.

Switch to generic power management framework using a single "struct dev_pm_ops"
variable to take the unnecessary load from the driver. This also avoids the
need for the driver to directly call most of the PCI helper functions and
device power state control functions, as through the generic framework PCI Core
takes care of the necessary operations, and drivers are required to do only
device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200728085757.888620-1-vaibhavgupta40@gmail.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CANFD_CLK_SEL_DIV_MASK and CANFD_OPTIONS_SET are
never used after they were introduced. Remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20200904131247.23021-1-wanghai38@huawei.com
[mkl: keep CANFD_CLK_SEL_DIV_MASK for documentation purpose]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Convert cpu_to_le32(le32_to_cpu(E1) + E2) to use le32_add_cpu().
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Link: https://lore.kernel.org/r/20200914041744.3701840-1-liushixin2@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Use the function devm_platform_ioremap_resource_byname() to simplify
source code which calls the functions platform_get_resource_byname()
and devm_ioremap_resource(). Remove also a few error messages which
became unnecessary with this software refactoring.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200420132207.8536-1-zhengdejin5@gmail.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As -Wimplicit-fallthrough is now enabled the mscan driver shows this warning,
which is fixed by this patch:

drivers/net/can/mscan/mscan.c: In function ‘mscan_start_xmit’:
drivers/net/can/mscan/mscan.c:211:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
  211 |   netif_stop_queue(dev);
      |   ^~~~~~~~~~~~~~~~~~~~~
drivers/net/can/mscan/mscan.c:212:2: note: here
  212 |  case 2:
      |  ^~~~

Link: https://lore.kernel.org/r/20200915223527.1417033-17-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The variable err is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200706164240.518623-1-colin.king@canonical.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

commit 524369e2 ("can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200505084149.23848-1-yuehaibing@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If a CAN device goes into bus-off and has automatic restart enabled, inform
user that a automatic restart is scheduled after the configured delay.

Link: https://lore.kernel.org/r/20200915223527.1417033-14-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In order to ease debugging let can_change_state() print the human readable
state change messages. Also print the old and new state.

Link: https://lore.kernel.org/r/20200915223527.1417033-13-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The function can_put_echo_skb() can fail for several reasons. It may
fail due to OOM, but when it fails it's usually due to locking problems
in the driver.

In order to help developing and debugging of new drivers propagate error
value in case of errors.

Link: https://lore.kernel.org/r/20200915223527.1417033-12-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch prints the number of the occupied echo_skb, to ease
implementing and debugging of new drivers.

Link: https://lore.kernel.org/r/20200915223527.1417033-11-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The "WITH Linux-syscall-note" exception is intended for UAPI headers.

See LICENSES/exceptions/Linux-syscall-note
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20200403073741.18352-1-masahiroy@kernel.orgAcked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

BerliOS has not been operating for more than five years. linux-can moved to
GitHub.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Link: https://lore.kernel.org/r/20200413170241.13207-1-flameeyes@flameeyes.com
[mkl: split into two patches - handle softing part here]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

BerliOS has not been operating for more than five years. linux-can moved to
GitHub.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Link: https://lore.kernel.org/r/20200413170241.13207-1-flameeyes@flameeyes.com
[mkl: split into two patches - handle slcan part here]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the indention to follow kernel coding style.

Link: https://lore.kernel.org/r/20200915223527.1417033-7-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes spelling erros found by "codespell" in the
drivers/net/can subtree.

Link: https://lore.kernel.org/r/20200915223527.1417033-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes spelling erros found by "codespell" in the net/can
subtree.

Link: https://lore.kernel.org/r/20200915223527.1417033-5-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes spelling erros found by "codespell" in the
include/linux/can subtree.

Link: https://lore.kernel.org/r/20200915223527.1417033-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fix a mistake in a register layout description.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200214141751.21168-1-alexandre.belloni@bootlin.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

There is a spelling mistake in a netdev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200806105616.46790-1-colin.king@canonical.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.

the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,n,flags;
@@

x =
- kcalloc
+ kmalloc_array
  (n,sizeof(*x),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.

the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,n,flags;
@@

x =
- kcalloc
+ kmalloc_array
  (n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
DSA with VLAN filtering and offloading masters

This series attempts to make DSA VLANs work in the presence of a master
interface that is:
- filtering, so it drops VLANs that aren't explicitly added to its
  filter list
- offloading, so the old assumptions in the tagging code about there
  being a VLAN tag in the skb are not necessarily true anymore.

For more context:
https://lore.kernel.org/netdev/20200910150738.mwhh2i6j2qgacqev@skbuf/

This probably marks the beginning of a series of patches in which DSA
starts paying much more attention to its upper interfaces, not only for
VLAN purposes but also for address filtering and for management of the
CPU flooding domain. There was a comment from Florian on whether we
could factor some of the mlxsw logic into some common functionality, but
it doesn't look so. This seems bound to be open-coded, but frankly there
isn't a lot to it.

Changes in v2:
Applied Florian's cosmetic suggestion in patch 4/9.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Check whether there is any hwaccel VLAN tag on RX, and if there is,
treat it as the tag_8021q header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The whole purpose of tag_8021q is to send VLAN-tagged traffic to the
CPU, from which the driver can decode the source port and switch id.

Currently this only works if the VLAN filtering on the master is
disabled. Change that by explicitly adding code to tag_8021q.c to add
the VLANs corresponding to the tags to the filter of the master
interface.

Because we now need to call vlan_vid_add, then we also need to hold the
RTNL mutex. Propagate that requirement to the callers of dsa_8021q_setup
and modify the existing call sites as appropriate. Note that one call
path, sja1105_best_effort_vlan_filtering_set -> sja1105_vlan_filtering
-> sja1105_setup_8021q_tagging, was already holding this lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most DSA switch tags shift the EtherType to the right, causing the
master to not parse the VLAN as VLAN.
However, not all switches do that (example: tail tags, tag_8021q etc),
and if the DSA master has "rx-vlan-filter: on" in ethtool -k, then we
have a problem.

Therefore, we could populate the VLAN table of the master, just in case
(for some switches it will not make a difference), so that network I/O
can work even with a VLAN filtering master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the bridge has VLAN awareness disabled there isn't any duplication
of functionality, since the bridge does not process VLAN. Don't deny
adding 8021q uppers to DSA switch ports in that case. The switch is
supposed to simply pass traffic leaving the VLAN tag as-is, and the
stack will happily strip the VLAN tag for all 8021q uppers that exist.

We need to ensure that there are no 8021q uppers when the user attempts
to enable bridge vlan_filtering.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current logic beats me a little bit. The comment that "bridge skips
-EOPNOTSUPP, so skip the prepare phase" was introduced in commit
fb2dabad ("net: dsa: support VLAN filtering switchdev attr").

I'm not sure:
(a) ok, the bridge skips -EOPNOTSUPP, but, so what, where are we
    returning -EOPNOTSUPP?
(b) even if we are, and I'm just not seeing it, what is the causality
    relationship between the bridge skipping -EOPNOTSUPP and DSA
    skipping the prepare phase, and just returning zero?

One thing is certain beyond doubt though, and that is that DSA currently
refuses VLAN filtering from the "commit" phase instead of "prepare", and
that this is not a good thing:

ip link add br0 type bridge
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br1
[ 3790.379389] 001: sja1105 spi0.1: VLAN filtering is a global setting
[ 3790.379399] 001: ------------[ cut here ]------------
[ 3790.379403] 001: WARNING: CPU: 1 PID: 515 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 3790.379420] 001: swp3: Commit of attribute (id=6) failed.
[ 3790.379533] 001: [<c11ff588>] (switchdev_port_attr_set_now) from [<c11b62e4>] (nbp_vlan_init+0x84/0x148)
[ 3790.379544] 001: [<c11b62e4>] (nbp_vlan_init) from [<c11a2ff0>] (br_add_if+0x514/0x670)
[ 3790.379554] 001: [<c11a2ff0>] (br_add_if) from [<c1031b5c>] (do_setlink+0x38c/0xab0)
[ 3790.379565] 001: [<c1031b5c>] (do_setlink) from [<c1036fe8>] (__rtnl_newlink+0x44c/0x748)
[ 3790.379573] 001: [<c1036fe8>] (__rtnl_newlink) from [<c1037328>] (rtnl_newlink+0x44/0x60)
[ 3790.379580] 001: [<c1037328>] (rtnl_newlink) from [<c10315fc>] (rtnetlink_rcv_msg+0x124/0x2f8)
[ 3790.379590] 001: [<c10315fc>] (rtnetlink_rcv_msg) from [<c10926b8>] (netlink_rcv_skb+0xb8/0x110)
[ 3790.379806] 001: ---[ end trace 0000000000000002 ]---
[ 3790.379819] 001: sja1105 spi0.1 swp3: failed to initialize vlan filtering on this port

So move the current logic that may fail (except ds->ops->port_vlan_filtering,
that is way harder) into the prepare stage of the switchdev transaction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is checking for the following order of operations, and makes sure
to deny that configuration:

ip link add link swp2 name swp2.100 type vlan id 100
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan add dev swp2 vid 100

Instead of using vlan_for_each(), which looks at the VLAN filters
installed with vlan_vid_add(), just track the 8021q uppers. This has the
advantage of freeing up the vlan_vid_add() call for actual VLAN
filtering.

There is another change in this patch. The check is moved in slave.c,
from switch.c. I don't think it makes sense to have this 8021q upper
check for each switch port that gets notified of that VLAN addition
(these include DSA links and CPU ports, we know those can't have 8021q
uppers because they don't have a net_device registered for them), so
just do it in slave.c, for that one slave interface.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA tries to prevent having a VLAN added by a bridge and by an 802.1Q
upper at the same time. It does that by checking the VID in
.ndo_vlan_rx_add_vid(), since that's something that the 8021q module
calls, via vlan_vid_add(). When a VLAN matches in both subsystems, this
check returns -EBUSY.

However the vlan_vid_add() function isn't specific to the 8021q module
in any way at all. It is simply the kernel's way to tell an interface to
add a VLAN to its RX filter and not drop that VLAN. So there's no reason
to return -EBUSY when somebody tries to call vlan_vid_add() for a VLAN
that was installed by the bridge. The proper behavior is to accept that
configuration.

So what's wrong is how DSA checks that it has an 8021q upper. It should
look at the actual uppers for that, not just assume that the 8021q
module was somewhere in the call stack of .ndo_vlan_rx_add_vid().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'll be adding a new check in the PRECHANGEUPPER notifier, where we'll
need to check some VLAN uppers. It is hard to do that when there is
already a function named dsa_slave_upper_vlan_check. So rename this one.

Not to mention that this function probably shouldn't have started with
"dsa_slave_" in the first place, since the struct net_device argument
isn't a DSA slave, but an 8021q upper of one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There doesn't seem to be any strong technical reason for doing it this
way, but we'll be adding more checks for invalid upper device
configurations, and it will be easier to have them all grouped under
PRECHANGEUPPER.

Tested that it still works:
ip link set br0 type bridge vlan_filtering 1
ip link add link swp2 name swp2.100 type vlan id 100
ip link set swp2.100 master br0
[   20.321312] br0: port 5(swp2.100) entered blocking state
[   20.326711] br0: port 5(swp2.100) entered disabled state
Error: dsa_core: Cannot enslave VLAN device into VLAN aware bridge.
[   20.346549] br0: port 5(swp2.100) entered blocking state
[   20.351957] br0: port 5(swp2.100) entered disabled state
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following W=1 kernel build warning(s):

drivers/net/ethernet/marvell/mvneta.c:754:6: warning:
 variable 'dummy' set but not used [-Wunused-but-set-variable]
  754 |  u32 dummy;
      |      ^~~~~

This variable is not used in function mvneta_mib_counters_clear(), so
remove it to avoid build warning.
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When budget is non-zero, skb_unref() has already handled the
NULL checking.

When budget is zero, the dev_consume_skb_any() has handled NULL
checking in __dev_kfree_skb_irq(), or dev_kfree_skb() which also
ultimately call skb_unref().

So remove the unnecessary checking in napi_consume_skb().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid copying skb_shared_info frags array in mvneta_swbm_build_skb() since
__build_skb_around() does not overwrite it
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We go to lengths to determine whether the PVID should be set
for this port or not, and then fail to take it into account.
Fix this oversight.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Murphy says:

====================
100base Fx link modes

As per patch https://lore.kernel.org/patchwork/patch/1300241/ the link
modes for 100base FX full and half duplex modes did not exist.  Adding
these link modes to the core and ethtool allow devices like the
DP83822, DP83869 and Broadcomm PHYs to properly advertise the correct
mode for Fiber 100Mbps.

Corresponding user land ethtool patches are available but rely on
these patches to be applied first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the fiber advertisement for speed and duplex modes with the
100base-FX full and half linkmode entries.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>