Some of the SVC request are already partially implement, whereas few
others are not. This patch implements and updates these requests.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

SVC connection is required before the AP knows its position on the endo
and type of endo. To enable message processing between the AP and SVC at
this time, we need a partially initialized connection which can handle
these messages.

Once the AP receives more information from the SVC, it can discard this
partially initialized connection and create a proper one, tied to a
bundle and interface.

Destroying the partially initialized connection is a bit tricky, as it
is required to send a response to svc-hello. That part will be properly
fixed separately.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We need to create bundle/connection for svc cport after the endo layout
and interface id is known to the AP. gb_create_control_connection() can
be reused for this, but it should be renamed to something more
appropriate, as its not about control-connection anymore.

Lets name it gb_create_bundle_connection().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We need a bundle-less connection for AP's SVC protocol, as that will be
used much before the endo layout and interface-id of the AP is known to
greybus core.

This updates gb_connection_create_range() to take few more arguments,
which were earlier fetched from the 'bundle' pointer.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We need to allocate specific hd-cport-id for AP's control/svc protocols.
Support that by splitting functionality of gb_connection_create() into a
new routine, which takes range of hd_cport_id's to allocate from.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

SVC is also a special protocol (like control) and AP doesn't need to
send (dis)connected events for its cport.

Lets skip them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

For now, the plan is to use a single cport for both control and svc
protocol. Defining separate macros for control and svc protocol's
cport/bundle would make the code more flexible, in case we need two
separate cports in future.

Lets define cport/bundle for svc protocol as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Define device-ids for AP, SVC and modules (starting id only).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Version response structure is also required by external entities like
gbsim and so its structure should be moved to greybus_protocols.h.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Class types aren't in sync with protocol types, lets keep them in sync
for now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We don't do what the comment says, drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Replace '* *' with '*'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The recently added GFP-flags argument to gb_message_send was never used.

Fixes: 9218fac2a24d ("operation: allow atomic request submissions")
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Response allocation also needs a GFP-flags argument as a response is
allocated as part of an outgoing operation.

Fixes: 9aa174d202e5 ("operation: allow atomic operation allocations")
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add list_last_entry macro for kernels older than 3.13.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add gb_operation_sync_timeout convenience function, which allows drivers
to configure the operation timeout.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add new interface gb_operation_request_send_sync_timeout, which allows
drivers to define a custom operation timeout instead of the default
one-second timeout.

The timeout is expected to depend on protocol and operation and
therefore needs to be configurable.

Note that that a timeout of zero is used to wait indefinitely.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Split incoming and outgoing operation-cancellation helpers.

Incoming operations are only cancelled as part of connection tear down
and is specifically not needed in the driver API.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure the request handler has submitted the response before
cancelling it during operation cancellation.

This prevents cancelling not-yet-submitted messages. It currently also
avoids us ending up with an active message on a stalled connection (e.g.
due to E2EFC).

Note that the call to gb_operation_result_set() is now redundant but is
kept as a precaution to guarantee that a response has indeed been
allocated as part of response submission.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to fully initialise the operation before adding it to the
active list when sending a request.

The operation should be fully initialised before adding it to the active
list to avoid racing with operation look up when receiving a response,
something which could potentially lead to a match against some earlier
(or intermediate) value of the id field.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to cancel all active operations before calling protocol
connection_exit to prevent use-after-free issues when the protocol state
is being deallocated (e.g. late processing of already-queued requests or
completions).

Note that already-queued requests or completions will be processed as
part of cancellation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fix connection tear down, which was done in an unsafe way that could
result in use-after-free as the per-connection list of operations was
iterated without any locking or refcounting.

Specifically, the operations list was iterated without holding any locks or
operation refcounts even though operations were being both removed from
the list and deallocated during per-operation cancellation. Any
operation completing during tear down could also cause corruption.

Change the per-connection operation list to only contain active
operations and use the recently introduced active counter to maintain
the list.

Add new helper that is called on connection tear down to cancel all
outstanding operations in a safe way by using proper locks and making
sure to hold a reference to any operation being cancelled.

Note that by verifying the connection state before incrementing the
active count we can make sure that all active operations have been
cancelled and that no new ones have been started when the helper
returns.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add locking, and the implied barriers, to connection-state updates.

This will be used to fix a number of races in the operations and
connection-tear-down implementations.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Suppress response submission on connection tear down as we do with
requests.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Call request handler helper explicitly from the work function rather
than overload the operation completion callback.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to call the operation completion callback also when the
operation is being cancelled.

The completion callback may need to release resources allocated at
submission and the driver should be informed that the operation has
failed due to cancellation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to wait for the operation to become inactive before returning
after having cancelled an operation.

This makes sure that any ongoing operation completion callbacks have
finished.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add active counter to track operations that are in use.

Note that the active count is always less than the reference count.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Clean up gb_operation_create_incoming error path by returning
immediately on allocation failures.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

An incoming operation could already be scheduled even if
gb_operation_result_set succeeds as its initial status is -EINPROGRESS.

Avoid potential use-after-free by never dropping the reference count for
incoming operations as part of cancellation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fixing needless redefinition of operation types in gbsim reveals this typo
GB_UART_TYPE_SET_BREAK -> GB_UART_TYPE_SEND_BREAK. This patch should be
applied in lock-step to the patch to gbsim 'gbsim/uart: remove unnecessary
redefinition of operation types' since gbsim does not contain the typo.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Last patchset missed compilation on 64 bit contained warning.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Copy/paste of code from one file to another missed inappropriate use of tab
after define.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Throughput capture should account for the entire size of the data going out
on the wire. In addition throughput should be captured for each supported
loopback operation.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Get maximum payload by way of gb_operation_get_payload_size_max() and
truncate any requested loopback size greater than this value. RX of data
from firmware over the specified size will not be accepted.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Loopback sink command will operate as an amalgam of the ping and tranfer
operations. Sink will send an ACK'd variable size operation over greybus.
Unlike the transfer type which transmits the received data back, the sink
type will simply ACK without sending the received data back.

This patch adds the kernel side of the sink command.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Sepcifying loopback operation type with a type value that is internal to
the loopback driver is non-intunitive and requires reading code to
understand. Remove confusing duplicate definitions and update code to
accept the greybus-specification function identity defintiions as the
appropriate type values for initiating loopback operations.

See greybus-spec section 10.16.1 'Greybus Loopback Message Types' for a
full list of valid messages to set this type field to.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Dangling debug code removed.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Magic number 2 used instead of define GB_LOOPBACK_TYPE_PING, remove and and
use the define instead.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In order to have one point of type definition for gbsim move the loopback
operation definitions to greybus_protocols.h.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>