- 22 Apr, 2017 33 commits
-
-
Uwe Kleine-König authored
commit f87e904d upstream. There are several issues fixed in this patch: - When alarm isn't enabled, set .enabled to zero instead of returning -EINVAL. - Ignore how IRQ1 is configured when determining if IRQ2 is on. - The three alarm registers have an enable flag which must be evaluated. - The chip always triggers when the seconds register gets 0. Note that the rtc framework however doesn't handle the result correctly because it doesn't check wday being initialized and so interprets an alarm being set for 10:00 AM in three days as 10:00 AM tomorrow (or today if that's not over yet). Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vitaly Kuznetsov authored
commit 77c0c973 upstream. When we iterate through all HA regions in handle_pg_range() we have an assumption that all these regions are sorted in the list and the 'start_pfn >= has->end_pfn' check is enough to find the proper region. Unfortunately it's not the case with WS2016 where host can hot-add regions in a different order. We end up modifying the wrong HA region and crashing later on pages online. Modify the check to make sure we found the region we were searching for while iterating. Fix the same check in pfn_covered() as well. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
bsegall@google.com authored
commit 5402e97a upstream. In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against __TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end of a PTRACE_LISTEN, this can wake the task /after/ the check against __TASK_TRACED, but before the reset of state to TASK_TRACED. This causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup against TRACED while the task is still on the rq wake_list, corrupting it. Oleg said: "The kernel can crash or this can lead to other hard-to-debug problems. In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced() assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the contract. Obviusly it is very wrong to manipulate task->state if this task is already running, or WAKING, or it sleeps again" [akpm@linux-foundation.org: coding-style fixes] Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL") Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.comSigned-off-by: Ben Segall <bsegall@google.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jan-Marek Glogowski authored
commit 806a28ef upstream. Currently the cifs module breaks the CIFS specs on reconnect as described in http://msdn.microsoft.com/en-us/library/cc246529.aspx: "TreeId (4 bytes): Uniquely identifies the tree connect for the command. This MUST be 0 for the SMB2 TREE_CONNECT Request." Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Tested-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heiko Carstens authored
commit d09c5373 upstream. Commit fd2d2b19 ("s390: get_user() should zero on failure") intended to fix s390's get_user() implementation which did not zero the target operand if the read from user space faulted. Unfortunately the patch has no effect: the corresponding inline assembly specifies that the operand is only written to ("=") and the previous value is discarded. Therefore the compiler is free to and actually does omit the zero initialization. To fix this simply change the contraint modifier to "+", so the compiler cannot omit the initialization anymore. Fixes: c9ca7841 ("s390/uaccess: provide inline variants of get_user/put_user") Fixes: fd2d2b19 ("s390: get_user() should zero on failure") Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marcelo Henrique Cerri authored
commit d82c0d12 upstream. Reorder the operations in decompress_kernel() to ensure initrd is moved to a safe location before the bss section is zeroed. During decompression bss can overlap with the initrd and this can corrupt the initrd contents depending on the size of the compressed kernel (which affects where the initrd is placed by the bootloader) and the size of the bss section of the decompressor. Also use the correct initrd size when checking for overlaps with parmblock. Fixes: 06c0dd72 ([S390] fix boot failures with compressed kernels) Reviewed-by: Joy Latten <joy.latten@canonical.com> Reviewed-by: Vineetha HariPai <vineetha.hari.pai@canonical.com> Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Martin authored
commit 7195ee31 upstream. It's not clear what behaviour is sensible when doing partial write of NT_METAG_RPIPE, so just don't bother. This patch assumes that userspace will never rely on a partial SETREGSET in this case, since it's not clear what should happen anyway. Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Martin authored
commit 5fe81fe9 upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill TXSTATUS, a well-defined default value is used, based on the task's current value. Suggested-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Martin authored
commit a78ce80d upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Martin authored
commit d3805c54 upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Martin authored
commit d614fd58 upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Martin authored
commit fb411b83 upstream. gpr_set won't work correctly and can never have been tested, and the correct behaviour is not clear due to the endianness-dependent task layout. So, just remove it. The core code will now return -EOPNOTSUPPORT when trying to set NT_PRSTATUS on this architecture until/unless a correct implementation is supplied. Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Li Qiang authored
commit e7e11f99 upstream. In vmw_surface_define_ioctl(), the 'num_sizes' is the sum of the 'req->mip_levels' array. This array can be assigned any value from the user space. As both the 'num_sizes' and the array is uint32_t, it is easy to make 'num_sizes' overflow. The later 'mip_levels' is used as the loop count. This can lead an oob write. Add the check of 'req->mip_levels' to avoid this. Signed-off-by: Li Qiang <liqiang6-s@360.cn> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Hellstrom authored
commit 53e16798 upstream. The mesa winsys sometimes uses unimplemented parameter requests to check for features. Remove the error message to avoid bloating the kernel log. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Hellstrom authored
commit fe25deb7 upstream. Previously, when a surface was opened using a legacy (non prime) handle, it was verified to have been created by a client in the same master realm. Relax this so that opening is also allowed recursively if the client already has the surface open. This works around a regression in svga mesa where opening of a shared surface is used recursively to obtain surface information. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Murray McAllister authored
commit 63774069 upstream. In vmw_get_cap_3d_ioctl(), a user can supply 0 for a size that is used in vzalloc(). This eventually calls dump_stack() (in warn_alloc()), which can leak useful addresses to dmesg. Add check to avoid a size of 0. Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Murray McAllister authored
commit 36274ab8 upstream. Before memory allocations vmw_surface_define_ioctl() checks the upper-bounds of a user-supplied size, but does not check if the supplied size is 0. Add check to avoid NULL pointer dereferences. Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Hellstrom authored
commit f7652afa upstream. A malicious caller could otherwise hand over handles to other objects causing all sorts of interesting problems. Testing done: Ran a Fedora 25 desktop using both Xorg and gnome-shell/Wayland. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paolo Bonzini authored
commit 06ce521a upstream. handle_vmon gets a reference on VMXON region page, but does not release it. Release the reference. Found by syzkaller; based on a patch by Dmitry. Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> [bwh: Backported to 3.16: use skip_emulated_instruction()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Amit Pundir authored
This reverts commit dbcfee72 which is commit be95485a upstream. Upstream commit be95485a (ARM: 8457/1: psci-smp is built only for SMP) was intended to fix the build error for configs with CONFIG_SMP=n and CONFIG_ARM_PSCI=y, but it end up introducing a build error when cherry-picked on 3.18.y. This patch resulted in redefinition of psci_init() and broke the build for every build config in 3.18.y with CONFIG_SMP=n and CONFIG_ARM_PSCI=y. Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Max Bires authored
commit f2cfa58b upstream. Without a bool string present, using "# CONFIG_DEVPORT is not set" in defconfig files would not actually unset devport. This esnured that /dev/port was always on, but there are reasons a user may wish to disable it (smaller kernel, attack surface reduction) if it's not being used. Adding a message here in order to make this user visible. Signed-off-by: Max Bires <jbires@google.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
commit 309124e2 upstream. According to full-history-linux commit d3794f4fa7c3edc3 ("[PATCH] M68k update (part 25)"), port operations are allowed on m68k if CONFIG_ISA is defined. However, commit 153dcc54 ("[PATCH] mem driver: fix conditional on isa i/o support") accidentally changed an "||" into an "&&", disabling it completely on m68k. This logic was retained when introducing the DEVPORT symbol in commit 4f911d64 ("Make /dev/port conditional on config symbol"). Drop the bogus dependency on !M68K to fix this. Fixes: 153dcc54 ("[PATCH] mem driver: fix conditional on isa i/o support") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Al Stone <ahs3@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Steven Rostedt (VMware) authored
commit 82cc4fc2 upstream. When two function probes are added to set_ftrace_filter, and then one of them is removed, the update to the function locations is not performed, and the record keeping of the function states are corrupted, and causes an ftrace_bug() to occur. This is easily reproducable by adding two probes, removing one, and then adding it back again. # cd /sys/kernel/debug/tracing # echo schedule:traceoff > set_ftrace_filter # echo do_IRQ:traceoff > set_ftrace_filter # echo \!do_IRQ:traceoff > /debug/tracing/set_ftrace_filter # echo do_IRQ:traceoff > set_ftrace_filter Causes: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 1098 at kernel/trace/ftrace.c:2369 ftrace_get_addr_curr+0x143/0x220 Modules linked in: [...] CPU: 2 PID: 1098 Comm: bash Not tainted 4.10.0-test+ #405 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012 Call Trace: dump_stack+0x68/0x9f __warn+0x111/0x130 ? trace_irq_work_interrupt+0xa0/0xa0 warn_slowpath_null+0x1d/0x20 ftrace_get_addr_curr+0x143/0x220 ? __fentry__+0x10/0x10 ftrace_replace_code+0xe3/0x4f0 ? ftrace_int3_handler+0x90/0x90 ? printk+0x99/0xb5 ? 0xffffffff81000000 ftrace_modify_all_code+0x97/0x110 arch_ftrace_update_code+0x10/0x20 ftrace_run_update_code+0x1c/0x60 ftrace_run_modify_code.isra.48.constprop.62+0x8e/0xd0 register_ftrace_function_probe+0x4b6/0x590 ? ftrace_startup+0x310/0x310 ? debug_lockdep_rcu_enabled.part.4+0x1a/0x30 ? update_stack_state+0x88/0x110 ? ftrace_regex_write.isra.43.part.44+0x1d3/0x320 ? preempt_count_sub+0x18/0xd0 ? mutex_lock_nested+0x104/0x800 ? ftrace_regex_write.isra.43.part.44+0x1d3/0x320 ? __unwind_start+0x1c0/0x1c0 ? _mutex_lock_nest_lock+0x800/0x800 ftrace_trace_probe_callback.isra.3+0xc0/0x130 ? func_set_flag+0xe0/0xe0 ? __lock_acquire+0x642/0x1790 ? __might_fault+0x1e/0x20 ? trace_get_user+0x398/0x470 ? strcmp+0x35/0x60 ftrace_trace_onoff_callback+0x48/0x70 ftrace_regex_write.isra.43.part.44+0x251/0x320 ? match_records+0x420/0x420 ftrace_filter_write+0x2b/0x30 __vfs_write+0xd7/0x330 ? do_loop_readv_writev+0x120/0x120 ? locks_remove_posix+0x90/0x2f0 ? do_lock_file_wait+0x160/0x160 ? __lock_is_held+0x93/0x100 ? rcu_read_lock_sched_held+0x5c/0xb0 ? preempt_count_sub+0x18/0xd0 ? __sb_start_write+0x10a/0x230 ? vfs_write+0x222/0x240 vfs_write+0xef/0x240 SyS_write+0xab/0x130 ? SyS_read+0x130/0x130 ? trace_hardirqs_on_caller+0x182/0x280 ? trace_hardirqs_on_thunk+0x1a/0x1c entry_SYSCALL_64_fastpath+0x18/0xad RIP: 0033:0x7fe61c157c30 RSP: 002b:00007ffe87890258 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: ffffffff8114a410 RCX: 00007fe61c157c30 RDX: 0000000000000010 RSI: 000055814798f5e0 RDI: 0000000000000001 RBP: ffff8800c9027f98 R08: 00007fe61c422740 R09: 00007fe61ca53700 R10: 0000000000000073 R11: 0000000000000246 R12: 0000558147a36400 R13: 00007ffe8788f160 R14: 0000000000000024 R15: 00007ffe8788f15c ? trace_hardirqs_off_caller+0xc0/0x110 ---[ end trace 99fa09b3d9869c2c ]--- Bad trampoline accounting at: ffffffff81cc3b00 (do_IRQ+0x0/0x150) Fixes: 59df055f ("ftrace: trace different functions with a different tracer") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Juergen Gross authored
commit 9121b15b upstream. Connecting to the backend isn't working reliably in xen-fbfront: in case XenbusStateInitWait of the backend has been missed the backend transition to XenbusStateConnected will trigger the connected state only without doing the actions required when the backend has connected. Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin K. Petersen authored
commit 7c856152 upstream. We previously made sure that the reported disk capacity was less than 0xffffffff blocks when the kernel was not compiled with large sector_t support (CONFIG_LBDAF). However, this check assumed that the capacity was reported in units of 512 bytes. Add a sanity check function to ensure that we only enable disks if the entire reported capacity can be expressed in terms of sector_t. Reported-by: Steve Magnani <steve.magnani@digidescorp.com> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin K. Petersen authored
commit a00a7862 upstream. Kefeng Wang discovered that old versions of the QEMU CD driver would return mangled mode data causing us to walk off the end of the buffer in an attempt to parse it. Sanity check the returned mode sense data. Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicholas Bellinger authored
commit 1c99de98 upstream. Once upon a time back in 2009, a work-around was added to support the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login did not propose nor respond to MaxBurstLength, FirstBurstLength, DefaultTime2Wait and DefaultTime2Retain keys. The work-around in iscsi_check_proposer_for_optional_reply() allowed the missing keys to be proposed, but did not require waiting for a response before moving to full feature phase operation. This allowed GlobalSAN v3.3 to work out-of-the box, and for many years we didn't run into login interopt issues with any other initiators.. Until recently, when Martin tried a QLogic 57840S iSCSI Offload HBA on Windows 2016 which completed login, but subsequently failed with: Got unknown iSCSI OpCode: 0x43 The issue was QLogic MSFT side did not propose DefaultTime2Wait + DefaultTime2Retain, so LIO proposes them itself, and immediately transitions to full feature phase because of the GlobalSAN hack. However, the QLogic MSFT side still attempts to respond to DefaultTime2Retain + DefaultTime2Wait, even though LIO has set ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT in last login response. So while the QLogic MSFT side should have been proposing these two keys to start, it was doing the correct thing per RFC-3720 attempting to respond to proposed keys before transitioning to full feature phase. All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541) does correctly propose the four keys during login, making the original work-around moot. So in order to allow QLogic MSFT to run unmodified as-is, go ahead and drop this long standing work-around. Reported-by: Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com> Cc: Arun Easi <arun.easi@cavium.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicholas Bellinger authored
commit efb2ea77 upstream. This patch fixes a iscsi-target specific TMR reference leak during session shutdown, that could occur when a TMR was quiesced before the hand-off back to iscsi-target code via transport_cmd_check_stop_to_fabric(). The reference leak happens because iscsit_free_cmd() was incorrectly skipping the final target_put_sess_cmd() for TMRs when transport_generic_free_cmd() returned zero because the se_cmd->cmd_kref did not reach zero, due to the missing se_cmd assignment in original code. The result was iscsi_cmd and it's associated se_cmd memory would be freed once se_sess->sess_cmd_map where released, but the associated se_tmr_req was leaked and remained part of se_device->dev_tmr_list. This bug would manfiest itself as kernel paging request OOPsen in core_tmr_lun_reset(), when a left-over se_tmr_req attempted to dereference it's se_cmd pointer that had already been released during normal session shutdown. To address this bug, go ahead and treat ISCSI_OP_SCSI_CMD and ISCSI_OP_SCSI_TMFUNC the same when there is an extra se_cmd->cmd_kref to drop in iscsit_free_cmd(), and use op_scsi to signal __iscsit_free_cmd() when the former needs to clear any further iscsi related I/O state. Reported-by: Rob Millner <rlm@daterainc.com> Cc: Rob Millner <rlm@daterainc.com> Reported-by: Chu Yuan Lin <cyl@datera.io> Cc: Chu Yuan Lin <cyl@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Krause authored
commit c06989da upstream. vdso_enabled can be set to arbitrary integer values via the kernel command line 'vdso32=' parameter or via 'sysctl abi.vsyscall32'. load_vdso32() only maps VDSO if vdso_enabled == 1, but ARCH_DLINFO_IA32 merily checks for vdso_enabled != 0. As a consequence the AT_SYSINFO_EHDR auxiliary vector for the VDSO_ENTRY is emitted with a NULL pointer which causes a segfault when the application tries to use the VDSO. Restrict the valid arguments on the command line and the sysctl to 0 and 1. Fixes: b0b49f26 ("x86, vdso: Remove compat vdso support") Signed-off-by: Mathias Krause <minipli@googlemail.com> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Roland McGrath <roland@redhat.com> Link: http://lkml.kernel.org/r/1491424561-7187-1-git-send-email-minipli@googlemail.com Link: http://lkml.kernel.org/r/20170410151723.518412863@linutronix.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Gleixner authored
commit 6fdc6dd9 upstream. The vsyscall32 sysctl can racy against a concurrent fork when it switches from disabled to enabled: arch_setup_additional_pages() if (vdso32_enabled) --> No mapping sysctl.vsysscall32() --> vdso32_enabled = true create_elf_tables() ARCH_DLINFO_IA32 if (vdso32_enabled) { --> Add VDSO entry with NULL pointer Make ARCH_DLINFO_IA32 check whether the VDSO mapping has been set up for the newly forked process or not. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mathias Krause <minipli@googlemail.com> Link: http://lkml.kernel.org/r/20170410151723.602367196@linutronix.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Zijlstra authored
commit f2200ac3 upstream. When the perf_branch_entry::{in_tx,abort,cycles} fields were added, intel_pmu_lbr_read_32() wasn't updated to initialize them. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Fixes: 135c5612 ("perf/x86/intel: Support Haswell/v4 LBR format") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Cameron Gutman authored
commit 53763668 upstream. Signed-off-by: Cameron Gutman <aicommander@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Germano Percossi authored
commit 1fa839b4 upstream. This fixes Continuous Availability when errors during file reopen are encountered. cifs_user_readv and cifs_user_writev would wait for ever if results of cifs_reopen_file are not stored and for later inspection. In fact, results are checked and, in case of errors, a chain of function calls leading to reads and writes to be scheduled in a separate thread is skipped. These threads will wake up the corresponding waiters once reads and writes are done. However, given the return value is not stored, when rc is checked for errors a previous one (always zero) is inspected instead. This leads to pending reads/writes added to the list, making cifs_user_readv and cifs_user_writev wait for ever. Signed-off-by: Germano Percossi <germano.percossi@citrix.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 18 Apr, 2017 7 commits
-
-
Greg Kroah-Hartman authored
-
Geert Uytterhoeven authored
commit 6c8afa88 upstream. The patch "module: fix types of device tables aliases" newly requires that invocations of MODULE_DEVICE_TABLE(type, name); come *after* the definition of `name'. That is reasonable, but gscps2 wasn't doing this. Fix it. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hannes Frederic Sowa authored
commit 72ef9c41 upstream. This patch fixes a memory leak, which happens if the connection request is not fulfilled between parsing the DCCP options and handling the SYN (because e.g. the backlog is full), because we forgot to free the list of ack vectors. Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jon Maxwell authored
commit 45caeaa5 upstream. As Eric Dumazet pointed out this also needs to be fixed in IPv6. v2: Contains the IPv6 tcp/Ipv6 dccp patches as well. We have seen a few incidents lately where a dst_enty has been freed with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that dst_entry. If the conditions/timings are right a crash then ensues when the freed dst_entry is referenced later on. A Common crashing back trace is: #8 [] page_fault at ffffffff8163e648 [exception RIP: __tcp_ack_snd_check+74] . . #9 [] tcp_rcv_established at ffffffff81580b64 #10 [] tcp_v4_do_rcv at ffffffff8158b54a #11 [] tcp_v4_rcv at ffffffff8158cd02 #12 [] ip_local_deliver_finish at ffffffff815668f4 #13 [] ip_local_deliver at ffffffff81566bd9 #14 [] ip_rcv_finish at ffffffff8156656d #15 [] ip_rcv at ffffffff81566f06 #16 [] __netif_receive_skb_core at ffffffff8152b3a2 #17 [] __netif_receive_skb at ffffffff8152b608 #18 [] netif_receive_skb at ffffffff8152b690 #19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3] #20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3] #21 [] net_rx_action at ffffffff8152bac2 #22 [] __do_softirq at ffffffff81084b4f #23 [] call_softirq at ffffffff8164845c #24 [] do_softirq at ffffffff81016fc5 #25 [] irq_exit at ffffffff81084ee5 #26 [] do_IRQ at ffffffff81648ff8 Of course it may happen with other NIC drivers as well. It's found the freed dst_entry here: 224 static bool tcp_in_quickack_mode(struct sock *sk)
↩ 225 {↩ 226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩ 227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩ 228↩ 229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩ 230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩ 231 }↩ But there are other backtraces attributed to the same freed dst_entry in netfilter code as well. All the vmcores showed 2 significant clues: - Remote hosts behind the default gateway had always been redirected to a different gateway. A rtable/dst_entry will be added for that host. Making more dst_entrys with lower reference counts. Making this more probable. - All vmcores showed a postitive LockDroppedIcmps value, e.g: LockDroppedIcmps 267 A closer look at the tcp_v4_err() handler revealed that do_redirect() will run regardless of whether user space has the socket locked. This can result in a race condition where the same dst_entry cached in sk->sk_dst_entry can be decremented twice for the same socket via: do_redirect()->__sk_dst_check()-> dst_release(). Which leads to the dst_entry being prematurely freed with another socket pointing to it via sk->sk_dst_cache and a subsequent crash. To fix this skip do_redirect() if usespace has the socket locked. Instead let the redirect take place later when user space does not have the socket locked. The dccp/IPv6 code is very similar in this respect, so fixing it there too. As Eric Garver pointed out the following commit now invalidates routes. Which can set the dst->obsolete flag so that ipv4_dst_check() returns null and triggers the dst_release(). Fixes: ceb33206 ("ipv4: Kill routes during PMTU/redirect updates.") Cc: Eric Garver <egarver@redhat.com> Cc: Hannes Sowa <hsowa@redhat.com> Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -
Dmitry V. Levin authored
commit 745cb7f8 upstream. Replace MAX_ADDR_LEN with its numeric value to fix the following linux/packet_diag.h userspace compilation error: /usr/include/linux/packet_diag.h:67:17: error: 'MAX_ADDR_LEN' undeclared here (not in a function) __u8 pdmc_addr[MAX_ADDR_LEN]; This is not the first case in the UAPI where the numeric value of MAX_ADDR_LEN is used instead of symbolic one, uapi/linux/if_link.h already does the same: $ grep MAX_ADDR_LEN include/uapi/linux/if_link.h __u8 mac[32]; /* MAX_ADDR_LEN */ There are no UAPI headers besides these two that use MAX_ADDR_LEN. Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Acked-by: Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Dumazet authored
commit 9ac25fc0 upstream. TX skbs do not necessarily hold a reference on skb->sk->sk_refcnt By the time TX completion happens, sk_refcnt might be already 0. sock_hold()/sock_put() would then corrupt critical state, like sk_wmem_alloc and lead to leaks or use after free. Fixes: 62bccb8c ("net-timestamp: Make the clone operation stand-alone from phy timestamping") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Dumazet authored
commit dd4f1072 upstream. TX skbs do not necessarily hold a reference on skb->sk->sk_refcnt By the time TX completion happens, sk_refcnt might be already 0. sock_hold()/sock_put() would then corrupt critical state, like sk_wmem_alloc. Fixes: bf7fa551 ("mac80211: Resolve sk_refcnt/sk_wmem_alloc issue in wifi ack path") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-