This commit fixes NOR flash recovery issues observed with Spansion
S29GL512N NOR.

When NOR erases, it first fills PEBs with zeroes, then sets all bytes
to 0xFF. Filling with zeroes starts from the end of the PEB. And when
power is cut, this results in PEBs containing correct EC and VID headers
but corrupted with zeros at the end. This confuses UBI and it mistakinly
accepts these PEBs and associate them with LEBs.

Fis this issue by zeroing EC and VID magics before erasing PEBs, to
make UBI later refuse zem.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

Move the image seq. number handling from I/O level to the scanning
lever, where it really belongs to. Move the @image_seq_set variable
to the @struct ubi_scan_info structure, which exists only during
scanning.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

An image sequence number is added to the UBI erase-counter header
to be able determine if the root file system contains a mixture
of old and new images (because the flashing failed to complete).

A change to nolo is also needed for this to take effect.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

The 'paranoid_check_empty()' is bogus because, which is easilly
seen on NOR flash, which has long erase cycles, and which may
easilly end-up with half-erased eraseblocks. In this case the
paranoid check fails. I is just wrong to assume that PEBs which
do not have EC headers always contain all 0xFF. Such assumption
should not be made on the I/O level, which is quite low.

Thus, just kill the check.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch adds code which makes sure eraseblocks contain all 0xFF
bytes before starting using them. The verification is done only when
debugging checks are enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

Commit 537a1bf0 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:

   Badness at kernel/mutex.c:207

   Pid : 1, Comm:          swapper
   CPU : 0                 Not tainted  (2.6.31-rc1-00284-g529ba0d9-dirty #2273)

   PC is at __mutex_lock_slowpath+0x72/0x1bc
   PR is at __mutex_lock_slowpath+0x66/0x1bc
   ...

matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (27 commits)
  parisc: use generic atomic64 on 32-bit
  parisc: superio: fix build breakage
  parisc: Fix PCI resource allocation on non-PAT SBA machines
  parisc: perf: wire up sys_perf_counter_open
  parisc: add task_pt_regs macro
  parisc: wire sys_perf_counter_open to sys_ni_syscall
  parisc: inventory.c, fix bloated stack frame
  parisc: processor.c, fix bloated stack frame
  parisc: fix compile warning in mm/init.c
  parisc: remove dead code from sys_parisc32.c
  parisc: wire up rt_tgsigqueueinfo
  parisc: ensure broadcast tlb purge runs single threaded
  parisc: fix "delay!" timer handling
  parisc: fix mismatched parenthesis in memcpy.c
  parisc: Fix gcc 4.4 warning in lba_pci.c
  parisc: add parameter to read_cr16()
  parisc: decode_exc.c should include kernel.h
  parisc: remove obsolete hw_interrupt_type
  parisc: fix irq compile bugs in arch/parisc/kernel/irq.c
  parisc: advertise PCI devs after "assign_resources"
  ...

Manually fixed up trivial conflicts in tools/perf/perf.h due to addition
of SH vs HPPA perf-counter support.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: fix pcap adc locking
  mfd: sm501, fix lock imbalance

* 'for-2.6.31' of git://linux-nfs.org/~bfields/linux:
  NFSD: Don't hold unrefcounted creds over call to nfsd_setuser()

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
  MIPS: Reorganize Cavium OCTEON PCI support.
  Update Yoichi Yuasa's e-mail address
  MIPS: Allow suspend and hibernation again on uniprocessor kernels.
  MIPS: 64-bit: Fix o32 core dump
  MIPS: BC47xx: Fix SSB irq setup
  MIPS: CMP: Update sync-r4k for current kernel
  MIPS: CMP: Move gcmp_probe to before the SMP ops
  MIPS: CMP: activate CMP support
  MIPS: CMP: Extend IPI handling to CPU number
  MIPS: CMP: Extend the GIC IPI interrupts beyond 32
  MIPS: Define __arch_swab64 for all mips r2 cpus
  MIPS: Update VR41xx GPIO driver to use gpiolib
  MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
  MIPS: Malta: Remove unnecessary function prototypes
  MIPS: MT: Remove unnecessary semicolons
  MIPS: Add support for Texas Instruments AR7 System-on-a-Chip

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: do not set DEVNAME for OSS devices
  ALSA: hda - Add sanity check in PCM open callback
  ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
  ALSA: hda - Avoid invalid formats and rates with shared SPDIF
  ALSA: hda - Improve ASUS eeePC 1000 mixer
  ALSA: hda - Add GPIO1 control at muting with HP laptops
  ALSA: usx2y - reparent sound device
  ALSA: snd_usb_caiaq: reparent sound device
  sound: virtuoso: fix Xonar D1/DX silence after resume
  ASoC: Only disable pxa2xx-i2s clocks if we enabled them
  ALSA: hda - Add quirk for HP 6930p
  ALSA: hda - Add missing static to patch_ca0110()
  ASoC: OMAP: fix OMAP1510 broken PCM pointer callback
  ASoC: remove BROKEN from Efika and pcm030 fabric drivers
  ASoC: Fix typo in MPC5200 PSC AC97 driver Kconfig

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: finally remove the obsolete variable $TOPDIR
  gitignore: ignore scripts/ihex2fw
  Kbuild: Disable the -Wformat-security gcc flag
  gitignore: ignore gcov output files
  kbuild: deb-pkg ship changelog
  Add new __init_task_data macro to be used in arch init_task.c files.
  asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
  Add new macros for page-aligned data and bss sections.
  asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: don't merge requests of different failfast settings
  cciss: Ignore stale commands after reboot

* fix/soundcore:
  sound: do not set DEVNAME for OSS devices

* fix/hda:
  ALSA: hda - Add sanity check in PCM open callback
  ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
  ALSA: hda - Avoid invalid formats and rates with shared SPDIF
  ALSA: hda - Improve ASUS eeePC 1000 mixer
  ALSA: hda - Add GPIO1 control at muting with HP laptops

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver.  This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max.  So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing.  If any of them can be zero, disable
the SPDIF sharing mode instead.  Otherwise it will lead to a PCM
configuration error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Block layer used to merge requests and bios with different failfast
settings.  This caused regular IOs to fail prematurely when they were
merged into failfast requests for readahead.

Niel Lambrechts could trigger the problem semi-reliably on ext4 when
resuming from STR.  ext4 uses readahead when reading inodes and
combined with the deterministic extra SATA PHY exception cycle during
resume on the specific configuration, non-readahead inode read would
fail causing ext4 errors.  Please read the following thread for
details.

  http://lkml.org/lkml/2009/5/23/21

This patch makes block layer reject merging if the failfast settings
don't match.  This is correct but likely to lower IO performance by
preventing regular IOs from mingling into surrounding readahead
requests.  Changes to allow such mixed merges and handle errors
correctly will be added later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Cc: Theodore Tso <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@carl.(none)>

When doing an unexpected shutdown like kexec the cciss
firmware might still have some commands in flight, which
it is trying to complete.
The driver is doing it's best on resetting the HBA,
but sadly there's a firmware issue causing the firmware
_not_ to abort or drop old commands.
So the firmware will send us commands which we haven't
accounted for, causing the driver to panic.

With this patch we're just ignoring these commands as
there is nothing we could be doing with them anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>

For systems which do not define PHYS_OFFSET as 0 pfn_valid() may falsely
have returned 0 on most configurations.  Bug introduced by commit
752fbeb2e3555c0d236e992f1195fd7ce30e728d (linux-mips.org) rsp.
6f284a2c (kernel.org) titled "[MIPS]
FLATMEM: introduce PHYS_OFFSET."
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Move the cavium PCI files to the arch/mips/pci directory.  Also cleanup
comment formatting and code layout.  Code from pci-common.c, was moved
into other files.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Pavel Machek <pavel@ucw.cz>

If an o32 process generates a core dump on a 64 bit kernel, the core file
will not be correctly recognized. This is because ELF_CORE_COPY_REGS and
ELF_CORE_COPY_TASK_REGS are not correctly defined for o32 and will use
the default register set which would be CONFIG_64BIT in asm/elf.h.

So we'll switch to use the right register defines in this situation by
checking for WANT_COMPAT_REG_H and use the right defines of
ELF_CORE_COPY_REGS and ELF_CORE_COPY_TASK_REGS.

[Ralf: made ELF_CORE_COPY_TASK_REGS() bullet-proof against funny arguments.]
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The current ssb irq setup in ssb_mipscore_init has the problem that it
configures some device on some irq without checking that the irq is not
taken by an other device.

For example in my case PCI host is on irq 0 and IPSEC on irq 3.
The current code:
  - store in dev->irq that IPSEC irq is 3 + 2
  - do a set_irq 0->3 on PCI host

But now IPSEC irq is not routed anymore to the mips code and dev->irq is
wrong.  This causes a problem described in [1].

This patch tries to solve the problem by making set_irq configure the
device we want to take the irq on the shared irq0. The previous example
becomes:
  - store in dev->irq that IPSEC irq is 3 + 2
  - do a set_irq 0->3 on PCI host:
  - irq 3 is already taken by IPSEC. do a set_irq 3->0 on IPSEC

I also added some code to print the irq configuration after irq setup to
allow easier debugging. And I add extra checking in ssb_mips_irq to report
device without irq or device with not routed irq.

[1] http://www.danm.de/files/src/bcm5365p/REPORTED_DEVICESSigned-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This revises the sync-4k so it will boot and operate since the removal of
expirelo from the timer code.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is to move the gcmp_probe call to before the use of and selection of
the smp_ops functions. This allows malta with 1004K to work.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Most of the CMP support was added before, this mostly correct compile
problems but adds a platform specific translation for the interrupt number
based on cpu number.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This takes the current IPI interrupt assignment from the fix number of 4
to the number of CPUs defined in the system.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch extends the GIC interrupt handling beyond the current 32 bit
range as well as extending the number of interrupts based on the number
of CPUs.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some CPUs implement mipsr2, but because they are a super-set of mips64r2 do
not define CONFIG_CPU_MIPS64_R2.  Cavium OCTEON falls into this category.
We would still like to use the optimized implementation, so since we have
already checked for CONFIG_CPU_MIPSR2, checking for CONFIG_64BIT instead of
CONFIG_CPU_MIPS64_R2 is sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yyuasa@linux.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[Ralf: I fixed up the numbering in the comment in scall64-n32.S.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@openwrt.org>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

nfsd_open() gets an unrefcounted pointer to the current process's effective
credentials at the top of the function, then calls nfsd_setuser() via
fh_verify() - which may replace and destroy the current process's effective
credentials - and then passes the unrefcounted pointer to dentry_open() - but
the credentials may have been destroyed by this point.

Instead, the value from current_cred() should be passed directly to
dentry_open() as one of its arguments, rather than being cached in a variable.

Possibly fh_verify() should return the creds to use.

This is a regression introduced by
745ca247 "CRED: Pass credentials through
dentry_open()".
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-and-Verified-By: Steve Dickson <steved@redhat.com>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>