These options make it possible to overwrites the data and instruction
prefetching behavior of the arm pl310 cache controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When dma-coherent transfers are enabled, the mmap call must
not change the pg_prot flags in the vma struct.

Split the arm_dma_mmap into a common and specific parts,
and add a "arm_coherent_dma_mmap" implementation that does
not alter the page protection flags.

Tested on a topic-miami board (Zynq) using the ACP port
to transfer data between FPGA and CPU using the Dyplo
framework. Without this patch, byte-wise access to mmapped
coherent DMA memory was about 20x slower because of the
memory being marked as non-cacheable, and transfer speeds
would not exceed 240MB/s.

After this patch, the mapped memory is cacheable and the
transfer speed is again 600MB/s (limited by the FPGA) when
the data is in the L2 cache, while data integrity is being
maintained.

The patch has no effect on non-coherent DMA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

A recent change in kernel/acct.c added a new warning for many
configurations on ARM:

kernel/acct.c: In function 'acct_pin_kill':
arch/arm/include/asm/cmpxchg.h:122:3: warning: value computed is not used [-Wunused-value]

The code is in fact correct, it's just a cmpxchg() call that
intentionally ignores the result, and no other code does that.  The
warning does not show up on x86 because of the way that its cmpxchg()
macro is written. This changes the ARM implementation to use a similar
construct with a compound expression instead of a typecast, which causes
the compiler to not complain about an unused result.

Fix the other macros in this file in a similar way, and place them
just below their function implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We want link errors if xchg() is called for a variable size we do not
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Vybrids has 112 peripheral interrupts which can be routed to the
Cortex-M4's NVIC interrupt controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 5261ef2ea836 ("ARM: 8366/1: move Dual-Timer SP804 driver to
drivers/clocksource") moved SP804 to drivers/clocksource resulting in
it being selectable on platforms/architectures without the config
GENERIC_SCHED_CLOCK enabled. Due to that, it results in the following
build failure(e.g. x86_64 allmodconfig)

drivers/built-in.o: In function `__sp804_clocksource_and_sched_clock_init':
(.init.text+0x1a0e7): undefined reference to `sched_clock_register'

This patch fixes the build by making ARM_TIMER_SP804 depend on
GENERIC_SCHED_CLOCK

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ARM Dual-Timer SP804 module is peripheral found not only on ARM32
platforms but also on ARM64 platforms.

This patch moves the driver out of arch/arm to driver/clocksource
so that it can be used on ARM64 platforms also.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The header asm/hardware/arm_timer.h is included in various machine
specific files to access TIMER_CTRL and initialise to a known state.

This patch introduces a new function sp804_timer_disable to disable
the SP804 timers and uses the same for initialising the timers to
known(off) state, thereby removing the dependency on the header
asm/hardware/arm_timer.h

This change is in prepartion to move sp804 timer support out of arch/arm
so that it can be used on ARM64 platforms.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The new veneer support for loadable modules on ARM uses the
__opcode_to_mem_thumb32() function to count R_ARM_THM_CALL
and R_ARM_THM_JUMP24 relocations.

However, this function is not defined for big-endian kernels
on ARMv5 or before, causing a compile-time error:

arch/arm/kernel/module-plts.c: In function 'count_plts':
arch/arm/kernel/module-plts.c:124:9: error: implicit declaration of function '__opcode_to_mem_thumb32' [-Werror=implicit-function-declaration]
         __opcode_to_mem_thumb32(0x07ff2fff)))
         ^

As we know that this part of the function is only needed for
Thumb2 kernels, and that those can never happen with BE32,
we can avoid the error by enclosing the code in an #ifdef.

Fixes: 7d485f64 ("ARM: 8220/1: allow modules outside of bl range")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Put secondary_startup_arm() prototype in arch/arm/include/asm/smp.h
so users doesn't have to add extern prototype in their code.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

secondary_startup_arm is used as ARM mode secondary start up function
when ther kernel is compiled in THUMB mode, however the label itself
is still in .thumb mode. readelf shows:

160979: c020a581   120 FUNC    GLOBAL DEFAULT    2 secondary_startup_arm

Make sure the label is in ARM mode as well.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Avoid passing the auxiliary control register value through the enable
method.  In the resume path, we have to read the value stored in
l2x0_saved_regs.aux_ctrl, only to have it immediately written back by
l2c_enable().  We can avoid this if we have __l2c_init() save the value
directly to l2x0_saved_regs.aux_ctrl before calling the specific enable
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some L2C caches have a bit which allows non-secure software to control
the cache lockdown.  Some platforms are unable to set this bit.  To
avoid receiving an abort while trying to unlock the cache lines, check
the state of this bit before unlocking.  We do this by providing a new
method in the l2c_init_data to perform the unlocking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

l2c_configure() does not follow the pattern of other l2c_* functions.
Fix this so that it does to avoid future confusion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Before calling the controller specific configuration function, write
the auxiliary control register first, so that bits shared with other
registers (such as the prefetch control register) are not overwritten
by the later write to the auxctrl register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

l2c_enable() is documented that it must not be called if the cache has
already been enabled.  Unfortunately, commit 6b49241a ("ARM: 8259/1:
l2c: Refactor the driver to use commit-like interface") changed this
without updating the comment, for very little reason.  Revert this
change and restore the expected behaviour.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This grabs the serial number shown in cpuinfo from the serial-number device-tree
property in priority. When booting with ATAGs (and without device-tree), the
provided number is still shown instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Open firmware is already using the serial-number property for passing the
device's serial number from the bootloader to the kernel. In addition, lshw
already has support for scanning this property.

The serial number is a string that somewhat represents the device's serial
number. It might come from some form of storage (e.g. an eeprom) and be
programmed at factory-time by the manufacturer or come from identification
bits available in e.g. the SoC (note that the soc_id property in the SoC bus
should hold a full account of those bits).

The serial number is taken as-is from the bootloader, so it is up to the
bootloader to define where the serial number comes from and what length it
should be. Some use cases for the serial number require it to have a maximum
length (e.g. for USB serial number) and some other cases imply more restrictions
on what the serial number should look like (e.g. in Android, the ro.serialno
property is usually a 16-bytes (plus one null byte) representation of a 64 bit
number).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If we are building for a LE platform, and we haven't overriden the
MMIO ops, then we can optimize the mem*io operations using the
standard string functions.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Loading modules far away from the kernel in memory is problematic
because the 'bl' instruction only has limited reach, and modules are not
built with PLTs. Instead of using the -mlong-calls option (which affects
all compiler emitted bl instructions, but not the ones in assembler),
this patch allocates some additional space at module load time, and
populates it with PLT like veneers when encountering relocations that
are out of range.

This should work with all relocations against symbols exported by the
kernel, including those resulting from GCC generated implicit function
calls for ftrace etc.

The module memory size increases by about 5% on average, regardless of
whether any PLT entries were actually needed. However, due to the page
based rounding that occurs when allocating module memory, the average
memory footprint increase is negligible.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Looks like apps can be made to segfault easily on armhf distros
just by running cpuburn-a8 in the background, then starting apt
get update unless erratum 430973 workaround is enabled. This happens
on r3p2 also, which has 430973 fixed in hardware.

Turns out the reason for this is some bootloaders incorrectly
setting the auxilary register IBE bit, which probably causes us
to hit erratum 687067 on Cortex-A8 later than r1p2.

If the bootloader incorrectly sets the IBE bit in the auxilary control
register for Cortex-A8 revisions with 430973 fixed in hardware, we
need to call flush BTAC/BTB to avoid segfaults probably caused by
erratum 687067. So let's flush BTAC/BTB unconditionally for Cortex-A8.
It won't do anything unless the IBE bit is set.

Note that we keep the erratum 430973 Kconfig option still around and
disabled for multiarch as it may be unsafe to enable for some secure
SoC. It is known safe to be enabled for n900, but won't do anything
on n900 as the IBE bit needs to be set with SMC.

Also note that SoCs probably should also add checks and print warnings
for the misconfigured IBE bit depending on the Cortex-A8 revision
so the bootloaders can be fixed Cortex-A8 revisions later than
r1p2 to not set the IBE bit.
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

commit 195bbcac ("ARM: 7500/1: io: avoid writeback addressing
modes for __raw_ accessors") disables writeback addressing modes for
raw i/o. However, the "+Q" output constraint forces the compiler to
disable load hoist optimizations (because the output constraint informs the
compiler of memory stores which the compiler assumes may alias other memory).

Since the relaxed accessors only guarantee ordering wrt i/o accesses to the
same device and not to main memory, there's never a possibility of an accessor
invalidating a hoisted load (because only non-i/o loads would have been hoisted).

The effect is especially noticable with complex address inputs in loops.
For example, the following code:

    #include <linux/kernel.h>
    #include <linux/io.h>

    static const int *remap;

    void wr_loop(void __iomem *base, int c, int val)
    {
            int i;

            for (i = 0; i < c; i++)
                    writew_relaxed(val, base + remap[c >> 2]);
    }

generates

           current master             |             this patch
 0: e3510000    cmp     r1, #0        |  0: e3510000    cmp     r1, #0
 4: d12fff1e    bxle    lr            |  4: d12fff1e    bxle    lr
 8: e3003000    movw    r3, #0        |  8: e3c1c003    bic     ip, r1, #3
 c: e3403000    movt    r3, #0        |  c: e6ff2072    uxth    r2, r2
10: e92d4010    push    {r4, lr}      | 10: e3a03000    mov     r3, #0
14: e6ff2072    uxth    r2, r2        | 14: e59cc000    ldr     ip, [ip]
18: e3c14003    bic     r4, r1, #3    | 18: e080000c    add     r0, r0, ip
1c: e593e000    ldr     lr, [r3]      |
20: e3a03000    mov     r3, #0        | 1c: e1c020b0    strh    r2, [r0]
                                      | 20: e2833001    add     r3, r3, #1
24: e79ec004    ldr     ip, [lr, r4]  | 24: e1530001    cmp     r3, r1
28: e080c00c    add     ip, r0, ip    | 28: 1afffffb    bne     1c
2c: e1cc20b0    strh    r2, [ip]      | 2c: e12fff1e    bx      lr
30: e2833001    add     r3, r3, #1    |
34: e1530001    cmp     r3, r1        |
38: 1afffff9    bne     24            |
                                      |
3c: e8bd8010    pop     {r4, pc}      |
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

From Cortex-M reference manuals, the nvic supports up to 240 interrupts.
So the number of entries in vectors table is up to 256.

This patch adds a new config flag to specify the number of external interrupts.
Some ifdeferies are added in order to respect the natural alignment without
wasting too much space on smaller systems.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.

Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.

This was exposed by a recent vDSO cleanup.

Fixes: e7d6eefa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull intel drm fixes from Dave Airlie.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull intel iommu updates from David Woodhouse:
 "This lays a little of the groundwork for upcoming Shared Virtual
  Memory support — fixing some bogus #defines for capability bits and
  adding the new ones, and starting to use the new wider page tables
  where we can, in anticipation of actually filling in the new fields
  therein.

  It also allows graphics devices to be assigned to VM guests again.
  This got broken in 3.17 by disallowing assignment of RMRR-afflicted
  devices.  Like USB, we do understand why there's an RMRR for graphics
  devices — and unlike USB, it's actually sane.  So we can make an
  exception for graphics devices, just as we do USB controllers.

  Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
  persistent requests.  X2APIC_OPT_OUT was added to the spec as a nasty
  hack to allow broken BIOSes to forbid us from using X2APIC when they
  do stupid and invasive things and would break if we did.

  Someone noticed that since Windows doesn't have full IOMMU support for
  DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
  initialising the IOMMU on the graphics unit altogether.

  This means that it would be available for use in "driver mode", where
  the IOMMU registers are made available through a BAR of the graphics
  device and the graphics driver can do SVM all for itself.

  So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
  SVM capabilities.  And even the platforms which *might*, if the
  planets had been aligned correctly, possibly have had SVM capability
  but which in practice actually don't"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: support extended root and context entries
  iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
  iommu/vt-d: Allow RMRR on graphics devices too
  iommu/vt-d: Print x2apic opt out info instead of printing a warning
  iommu/vt-d: kill bogus ecap_niotlb_iunits()

Pull i2c fixes from Wolfram Sang:
 "This has a mixture of merge window cleanups and bugfixes"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: st: add include for pinctrl
  i2c: mux: use proper dev when removing "channel-X" symlinks
  i2c: digicolor: remove duplicate include
  i2c: Mark adapter devices with pm_runtime_no_callbacks
  i2c: pca-platform: fix broken email address
  i2c: mxs: fix broken email address
  i2c: rk3x: report number of messages transmitted

Pull btrfs fixes from Chris Mason:
 "Filipe hit two problems in my block group cache patches.  We finalized
  the fixes last week and ran through more tests"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: prevent list corruption during free space cache processing
  Btrfs: fix inode cache writeout

Merge tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel into drm-fixes

three fixes for i915.

* tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull NFS client updates from Trond Myklebust:
 "Another set of mainly bugfixes and a couple of cleanups.  No new
  functionality in this round.

  Highlights include:

  Stable patches:
   - Fix a regression in /proc/self/mountstats
   - Fix the pNFS flexfiles O_DIRECT support
   - Fix high load average due to callback thread sleeping

  Bugfixes:
   - Various patches to fix the pNFS layoutcommit support
   - Do not cache pNFS deviceids unless server notifications are enabled
   - Fix a SUNRPC transport reconnection regression
   - make debugfs file creation failure non-fatal in SUNRPC
   - Another fix for circular directory warnings on NFSv4 "junctioned"
     mountpoints
   - Fix locking around NFSv4.2 fallocate() support
   - Truncating NFSv4 file opens should also sync O_DIRECT writes
   - Prevent infinite loop in rpcrdma_ep_create()

  Features:
   - Various improvements to the RDMA transport code's handling of
     memory registration
   - Various code cleanups"

* tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (55 commits)
  fs/nfs: fix new compiler warning about boolean in switch
  nfs: Remove unneeded casts in nfs
  NFS: Don't attempt to decode missing directory entries
  Revert "nfs: replace nfs_add_stats with nfs_inc_stats when add one"
  NFS: Rename idmap.c to nfs4idmap.c
  NFS: Move nfs_idmap.h into fs/nfs/
  NFS: Remove CONFIG_NFS_V4 checks from nfs_idmap.h
  NFS: Add a stub for GETDEVICELIST
  nfs: remove WARN_ON_ONCE from nfs_direct_good_bytes
  nfs: fix DIO good bytes calculation
  nfs: Fetch MOUNTED_ON_FILEID when updating an inode
  sunrpc: make debugfs file creation failure non-fatal
  nfs: fix high load average due to callback thread sleeping
  NFS: Reduce time spent holding the i_mutex during fallocate()
  NFS: Don't zap caches on fallocate()
  xprtrdma: Make rpcrdma_{un}map_one() into inline functions
  xprtrdma: Handle non-SEND completions via a callout
  xprtrdma: Add "open" memreg op
  xprtrdma: Add "destroy MRs" memreg op
  xprtrdma: Add "reset MRs" memreg op
  ...

Pull fourth vfs update from Al Viro:
 "d_inode() annotations from David Howells (sat in for-next since before
  the beginning of merge window) + four assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  RCU pathwalk breakage when running into a symlink overmounting something
  fix I_DIO_WAKEUP definition
  direct-io: only inc/dec inode->i_dio_count for file systems
  fs/9p: fix readdir()
  VFS: assorted d_backing_inode() annotations
  VFS: fs/inode.c helpers: d_inode() annotations
  VFS: fs/cachefiles: d_backing_inode() annotations
  VFS: fs library helpers: d_inode() annotations
  VFS: assorted weird filesystems: d_inode() annotations
  VFS: normal filesystems (and lustre): d_inode() annotations
  VFS: security/: d_inode() annotations
  VFS: security/: d_backing_inode() annotations
  VFS: net/: d_inode() annotations
  VFS: net/unix: d_backing_inode() annotations
  VFS: kernel/: d_inode() annotations
  VFS: audit: d_backing_inode() annotations
  VFS: Fix up some ->d_inode accesses in the chelsio driver
  VFS: Cachefiles should perform fs modifications on the top layer only
  VFS: AF_UNIX sockets should call mknod on the top layer only

Pull more power management and ACPI updates from Rafael Wysocki:
 "These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
  cpupower tool), a new CPU ID for the Intel RAPL driver and one
  intel_pstate driver improvement that didn't make it to my previous
  pull requests due to timing.

  Specifics:

   - Fix a build warning in the intel_pstate driver showing up in
     non-SMP builds (Borislav Petkov)

   - Change one of the intel_pstate's P-state selection parameters for
     Baytrail and Cherrytrail CPUs to significantly improve performance
     at the cost of a small increase in energy consumption (Kristen
     Carlson Accardi)

   - Fix a NULL pointer dereference in the ACPI EC driver due to an
     unsafe list walk in the query handler removal routine (Chris
     Bainbridge)

   - Get rid of a false-positive lockdep warning in the ACPI container
     hot-remove code (Rafael J Wysocki)

   - Prevent the ACPI device enumeration code from creating device
     objects of a wrong type in some cases (Rafael J Wysocki)

   - Add Skylake processors support to the Intel RAPL power capping
     driver (Brian Bian)

   - Drop the stale MAINTAINERS entry for the ACPI dock driver that is
     regarded as part of the ACPI core and maintained along with it now
     (Chao Yu)

   - Fix cpupower tool breakage caused by a library API change in libpci
     3.3.0 (Lucas Stach)"

* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / scan: Add a scan handler for PRP0001
  ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
  ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
  MAINTAINERS: remove maintainship entry of docking station driver
  powercap / RAPL: Add support for Intel Skylake processors
  cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
  intel_pstate: Change the setpoint for Atom params
  cpupower: fix breakage from libpci API change

Pull crypto fixes from Herbert Xu:
 "This push fixes a build problem with img-hash under non-standard
  configurations and a serious regression with sha512_ssse3 which can
  lead to boot failures"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
  crypto: x86/sha512_ssse3 - fixup for asm function prototype change

Merge tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "This series includes significant updates to the toshiba_acpi driver
  and the reintroduction of the dell-laptop keyboard backlight additions
  I had to revert previously.  Also included are various fixes for
  typos, warnings, correctness, and minor bugs.

  Specifics:

  dell-laptop:
     - add support for keyboard backlight.

  toshiba_acpi:
     - adaptive keyboard, hotkey, USB sleep and charge, and backlight
       updates.  Update sysfs documentation.

  toshiba_bluetooth:
     - fix enabling/disabling loop on recent devices

  apple-gmux:
     - lock iGP IO to protect from vgaarb changes

  other:
     - Fix typos, clear gcc warnings, clarify pr_* messages, correct
       return types, update MAINTAINERS"

* tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (25 commits)
  toshiba_acpi: Do not register vendor backlight when acpi_video bl is available
  MAINTAINERS: Add me on list of Dell laptop drivers
  platform: x86: dell-laptop: Add support for keyboard backlight
  Documentation/ABI: Update sysfs-driver-toshiba_acpi entry
  toshiba_acpi: Fix pr_* messages from USB Sleep Functions
  toshiba_acpi: Update and fix USB Sleep and Charge modes
  wmi: Use bool function return values of true/false not 1/0
  toshiba_bluetooth: Fix enabling/disabling loop on recent devices
  toshiba_bluetooth: Clean up *_add function and disable BT device at removal
  toshiba_bluetooth: Add three new functions to the driver
  toshiba_acpi: Fix the enabling of the Special Functions
  toshiba_acpi: Use the Hotkey Event Type function for keymap choosing
  toshiba_acpi: Add Hotkey Event Type function and definitions
  x86/wmi: delete unused wmi_data_lock mutex causing gcc warning
  apple-gmux: lock iGP IO to protect from vgaarb changes
  MAINTAINERS: Add missing Toshiba devices and add myself as maintainer
  toshiba_acpi: Update events in toshiba_acpi_notify
  intel-oaktrail: Fix trivial typo in comment
  thinkpad_acpi: off by one in adaptive_keyboard_hotkey_notify_hotkey()
  thinkpad_acpi: signedness bugs getting current_mode
  ...

Pull chrome platform updates from Olof Johansson:
 "Here's a set of updates to the Chrome OS platform drivers for this
  merge window.

  Main new things this cycle is:

   - Driver changes to expose the lightbar to users.  With this, you can
     make your own blinkenlights on Chromebook Pixels.

   - Changes in the way that the atmel_mxt trackpads are probed.  The
     laptop driver is trying to be smart and not instantiate the devices
     that don't answer to probe.  For the trackpad that can come up in
     two modes (bootloader or regular), this gets complicated since the
     driver already knows how to handle the two modes including the
     actual addresses used.  So now the laptop driver needs to know more
     too, instantiating the regular address even if the bootloader one
     is the probe that passed.

   - mfd driver improvements by Javier Martines Canillas, and a few
     bugfixes from him, kbuild and myself"

* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  platform/chrome: chromeos_laptop - instantiate Atmel at primary address
  platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
  platform/chrome: cros_ec_lpc - Include linux/io.h header file
  platform/chrome: fix platform_no_drv_owner.cocci warnings
  platform/chrome: cros_ec_lightbar - fix duplicate const warning
  platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
  platform/chrome: Expose Chrome OS Lightbar to users
  platform/chrome: Create sysfs attributes for the ChromeOS EC
  mfd: cros_ec: Instantiate ChromeOS EC character device
  platform/chrome: Add Chrome OS EC userspace device interface
  platform/chrome: Add cros_ec_lpc driver for x86 devices
  mfd: cros_ec: Add char dev and virtual dev pointers
  mfd: cros_ec: Use fixed size arrays to transfer data with the EC

Pull arch/cris updates from Jesper Nilsson:
 "Some much needed love for the CRIS-port.

  There's a bunch of changes this time, giving the CRISv32 port a bit of
  modern makeover with device-tree, irq domain and gpiolib support, and
  more switchover to generic frameworks.

  Some small fixes and removal of the theoretical SMP support brings up
  the rear"

* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
  cris: fix integer overflow in ELF_ET_DYN_BASE
  CRISv32: use GENERIC_SCHED_CLOCK
  CRISv32: use MMIO clocksource
  CRISv32: use generic clockevents
  CRIS: use generic headers via Kbuild
  CRIS: use generic cmpxchg.h
  CRIS: use generic atomic.h
  CRIS: use generic atomic bitops
  CRISv10: remove redundant macros from system.h
  CRIS: remove SMP code
  CRISv32: don't enable irqs in INIT_THREAD
  CRISv32: handle multiple signals
  CRISv32: prevent bogus restarts on sigreturn
  CRISv32: don't attempt syscall restart on irq exit
  Add binding documentation for CRIS
  CRIS: add Axis 88 board device tree
  CRISv32: add device tree support
  CRISv32: add irq domains support
  CRIS: enable GPIOLIB

Pull powerpc fixes from Michael Ellerman:

 - fix for mm_dec_nr_pmds() from Scott.

 - fixes for oopses seen with KVM + THP from Aneesh.

 - build fixes from Aneesh & Shreyas.

* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
  powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
  powerpc/mm/thp: Return pte address if we find trans_splitting.
  powerpc/mm/thp: Make page table walk safe against thp split/collapse
  KVM: PPC: Remove page table walk helpers
  KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
  powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()

Pull second batch of KVM changes from Paolo Bonzini:
 "This mostly includes the PPC changes for 4.1, which this time cover
  Book3S HV only (debugging aids, minor performance improvements and
  some cleanups).  But there are also bug fixes and small cleanups for
  ARM, x86 and s390.

  The task_migration_notifier revert and real fix is still pending
  review, but I'll send it as soon as possible after -rc1"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
  KVM: arm/arm64: check IRQ number on userland injection
  KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
  KVM: VMX: Preserve host CR4.MCE value while in guest mode.
  KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
  KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
  KVM: PPC: Book3S HV: Streamline guest entry and exit
  KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
  KVM: PPC: Book3S HV: Use decrementer to wake napping threads
  KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
  KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
  KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
  KVM: PPC: Book3S HV: Minor cleanups
  KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
  KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
  KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
  KVM: PPC: Book3S HV: Add ICP real mode counters
  KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
  KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
  KVM: PPC: Book3S HV: Add guest->host real mode completion counters
  KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
  ...