- 03 Jul, 2019 12 commits
-
-
Ville Syrjälä authored
commit 59f9e9ca upstream. If we have only a single active pipe and the cdclk change only requires the cd2x divider to be updated bxt+ can do the update with forcing a full modeset on the pipe. Try to hook that up. v2: - Wait for vblank after an optimized CDCLK change. - Avoid optimization if the pipe needs a modeset (or was disabled). - Split CDCLK change to a pre/post plane update step. v3: - Use correct version of CDCLK state as old state. (Ville) - Remove unused intel_cdclk_can_skip_modeset() v4: - For consistency call intel_set_cdclk_post_plane_update() only during modesets (and not fastsets). v5: - Remove the logic to update the CD2X divider on-the-fly on ICL, since only a divider of 1 is supported there. Clint also noticed that the pipe select bits in CDCLK_CTL are oddly defined on ICL, it's not clear yet whether that's only an error in the specification. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Abhay Kumar <abhay.kumar@intel.com> Tested-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Clint Taylor <Clinton.A.Taylor@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190327101321.3095-1-imre.deak@intel.comSigned-off-by:
Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Imre Deak authored
commit 2b21dfbe upstream. We copied the original state into the atomic state already earlier in the function, so no need to do it a second time. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Imre Deak authored
commit 48d9f87d upstream. The old state will be needed by an upcoming patch to determine if the commit increases or decreases CDCLK, so move the old state to the atomic state (while keeping the new one in dev_priv). cdclk.logical and cdclk.actual in the atomic state isn't used atm anywhere after the atomic check phase, so this should be safe. v2: - Use swap() instead of opencoding it. (Ville) Suggested-by:
-
Ville Syrjälä authored
commit 905801fe upstream. CDCLK has to be at least twice the BLCK regardless of audio. Audio driver has to probe using this hook and increase the clock even in absence of any display. v2: Use atomic refcount for get_power, put_power so that we can call each once(Abhay). v3: Reset power well 2 to avoid any transaction on iDisp link during cdclk change(Abhay). v4: Remove Power well 2 reset workaround(Ville). v5: Remove unwanted Power well 2 register defined in v4(Abhay). v6: - Use a dedicated flag instead of state->modeset for min CDCLK changes - Make get/put audio power domain symmetric - Rebased on top of intel_wakeref tracking changes. Signed-off-by:
-
Dinh Nguyen authored
commit 74684cce upstream. The fixed dividers for the emac clocks should be 2 not 4. Cc: stable@vger.kernel.org Signed-off-by:
Dinh Nguyen <dinguyen@kernel.org> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Jon Hunter authored
commit 9caec662 upstream. Currently the default clock rates for the HDA and HDA2CODEC_2X clocks are both 19.2MHz. However, the default rates for these clocks should actually be 51MHz and 48MHz, respectively. The current clock settings results in a distorted output during audio playback. Correct the default clock rates for these clocks by specifying them in the clock init table for Tegra210. Cc: stable@vger.kernel.org Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Acked-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Jann Horn authored
commit 867bfa4a upstream. load_flat_shared_library() is broken: It only calls load_flat_file() if prepare_binprm() returns zero, but prepare_binprm() returns the number of bytes read - so this only happens if the file is empty. Instead, call into load_flat_file() if the number of bytes read is non-negative. (Even if the number of bytes is zero - in that case, load_flat_file() will see nullbytes and return a nice -ENOEXEC.) In addition, remove the code related to bprm creds and stop using prepare_binprm() - this code is loading a library, not a main executable, and it only actually uses the members "buf", "file" and "filename" of the linux_binprm struct. Instead, call kernel_read() directly. Link: http://lkml.kernel.org/r/20190524201817.16509-1-jannh@google.com Fixes: 287980e4 ("remove lots of IS_ERR_VALUE abuses") Signed-off-by:
Jann Horn <jannh@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Kees Cook <keescook@chromium.org> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
zhong jiang authored
commit 29b190fa upstream. mpol_rebind_nodemask() is called for MPOL_BIND and MPOL_INTERLEAVE mempoclicies when the tasks's cpuset's mems_allowed changes. For policies created without MPOL_F_STATIC_NODES or MPOL_F_RELATIVE_NODES, it works by remapping the policy's allowed nodes (stored in v.nodes) using the previous value of mems_allowed (stored in w.cpuset_mems_allowed) as the domain of map and the new mems_allowed (passed as nodes) as the range of the map (see the comment of bitmap_remap() for details). The result of remapping is stored back as policy's nodemask in v.nodes, and the new value of mems_allowed should be stored in w.cpuset_mems_allowed to facilitate the next rebind, if it happens. However, 213980c0 ("mm, mempolicy: simplify rebinding mempolicies when updating cpusets") introduced a bug where the result of remapping is stored in w.cpuset_mems_allowed instead. Thus, a mempolicy's allowed nodes can evolve in an unexpected way after a series of rebinding due to cpuset mems_allowed changes, possibly binding to a wrong node or a smaller number of nodes which may e.g. overload them. This patch fixes the bug so rebinding again works as intended. [vbabka@suse.cz: new changlog] Link: http://lkml.kernel.org/r/ef6a69c6-c052-b067-8f2c-9d615c619bb9@suse.cz Link: http://lkml.kernel.org/r/1558768043-23184-1-git-send-email-zhongjiang@huawei.com Fixes: 213980c0 ("mm, mempolicy: simplify rebinding mempolicies when updating cpusets") Signed-off-by:
zhong jiang <zhongjiang@huawei.com> Reviewed-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Oscar Salvador <osalvador@suse.de> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
John Ogness authored
commit cb8f381f upstream. 0a1eb2d4 ("fs/proc: Stop reporting eip and esp in /proc/PID/stat") stopped reporting eip/esp and fd7d5627 ("fs/proc: Report eip/esp in /prod/PID/stat for coredumping") reintroduced the feature to fix a regression with userspace core dump handlers (such as minicoredumper). Because PF_DUMPCORE is only set for the primary thread, this didn't fix the original problem for secondary threads. Allow reporting the eip/esp for all threads by checking for PF_EXITING as well. This is set for all the other threads when they are killed. coredump_wait() waits for all the tasks to become inactive before proceeding to invoke a core dumper. Link: http://lkml.kernel.org/r/87y32p7i7a.fsf@linutronix.de Link: http://lkml.kernel.org/r/20190522161614.628-1-jlu@pengutronix.de Fixes: fd7d5627 ("fs/proc: Report eip/esp in /prod/PID/stat for coredumping") Signed-off-by:
John Ogness <john.ogness@linutronix.de> Reported-by:
Jan Luebbe <jlu@pengutronix.de> Tested-by:
-
Bjørn Mork authored
[ Upstream commit 904d88d7 ] The syzbot reported Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x67/0x231 mm/kasan/report.c:188 __kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317 kasan_report+0xe/0x20 mm/kasan/common.c:614 qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417 usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361 really_probe+0x281/0x660 drivers/base/dd.c:509 driver_probe_device+0x104/0x210 drivers/base/dd.c:670 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 Caused by too many confusing indirections and casts. id->driver_info is a pointer stored in a long. We want the pointer here, not the address of it. Thanks-to: Hillf Danton <hdanton@sina.com> Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com Cc: Kristian Evensen <kristian.evensen@gmail.com> Fixes: e4bf6348 ("qmi_wwan: Add quirk for Quectel dynamic config") Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sasha Levin authored
This reverts commit b65b70ba, which was upstream commit 4a6c91fb. On Tue, Jun 25, 2019 at 09:39:45AM +0200, Sebastian Andrzej Siewior wrote: >Please backport commit e74deb11 to >stable _or_ revert the backport of commit 4a6c91fb ("x86/uaccess, >ftrace: Fix ftrace_likely_update() vs. SMAP"). It uses >user_access_{save|restore}() which has been introduced in the following >commit. Signed-off-by:
-
Nathan Chancellor authored
commit fa63da2a upstream. This is a GCC only option, which warns about ABI changes within GCC, so unconditionally adding it breaks Clang with tons of: warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option] and link time failures: ld.lld: error: undefined symbol: __efistub___stack_chk_guard >>> referenced by arm-stub.c:73 (/home/nathan/cbl/linux/drivers/firmware/efi/libstub/arm-stub.c:73) >>> arm-stub.stub.o:(__efistub_install_memreserve_table) in archive ./drivers/firmware/efi/libstub/lib.a These failures come from the lack of -fno-stack-protector, which is added via cc-option in drivers/firmware/efi/libstub/Makefile. When an unknown flag is added to KBUILD_CFLAGS, clang will noisily warn that it is ignoring the option like above, unlike gcc, who will just error. $ echo "int main() { return 0; }" > tmp.c $ clang -Wno-psabi tmp.c; echo $? warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option] 1 warning generated. 0 $ gcc -Wsometimes-uninitialized tmp.c; echo $? gcc: error: unrecognized command line option ‘-Wsometimes-uninitialized’; did you mean ‘-Wmaybe-uninitialized’? 1 For cc-option to work properly with clang and behave like gcc, -Werror is needed, which was done in commit c3f0d0bc ("kbuild, LLVMLinux: Add -Werror to cc-option to support clang"). $ clang -Werror -Wno-psabi tmp.c; echo $? error: unknown warning option '-Wno-psabi' [-Werror,-Wunknown-warning-option] 1 As a consequence of this, when an unknown flag is unconditionally added to KBUILD_CFLAGS, it will cause cc-option to always fail and those flags will never get added: $ clang -Werror -Wno-psabi -fno-stack-protector tmp.c; echo $? error: unknown warning option '-Wno-psabi' [-Werror,-Wunknown-warning-option] 1 This can be seen when compiling the whole kernel as some warnings that are normally disabled (see below) show up. The full list of flags missing from drivers/firmware/efi/libstub are the following (gathered from diffing .arm64-stub.o.cmd): -fno-delete-null-pointer-checks -Wno-address-of-packed-member -Wframe-larger-than=2048 -Wno-unused-const-variable -fno-strict-overflow -fno-merge-all-constants -fno-stack-check -Werror=date-time -Werror=incompatible-pointer-types -ffreestanding -fno-stack-protector Use cc-disable-warning so that it gets disabled for GCC and does nothing for Clang. Fixes: ebcc5928 ("arm64: Silence gcc warnings about arch ABI drift") Link: https://github.com/ClangBuiltLinux/linux/issues/511Reported-by:
Qian Cai <cai@lca.pw> Acked-by:
Dave Martin <Dave.Martin@arm.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
- 25 Jun, 2019 28 commits
-
-
Greg Kroah-Hartman authored
-
Michael Ellerman authored
commit ca72d883 upstream. When using the Hash Page Table (HPT) MMU, userspace memory mappings are managed at two levels. Firstly in the Linux page tables, much like other architectures, and secondly in the SLB (Segment Lookaside Buffer) and HPT. It's the SLB and HPT that are actually used by the hardware to do translations. As part of the series adding support for 4PB user virtual address space using the hash MMU, we added support for allocating multiple "context ids" per process, one for each 512TB chunk of address space. These are tracked in an array called extended_id in the mm_context_t of a process that has done a mapping above 512TB. If such a process forks (ie. clone(2) without CLONE_VM set) it's mm is copied, including the mm_context_t, and then init_new_context() is called to reinitialise parts of the mm_context_t as appropriate to separate the address spaces of the two processes. The key step in ensuring the two processes have separate address spaces is to allocate a new context id for the process, this is done at the beginning of hash__init_new_context(). If we didn't allocate a new context id then the two processes would share mappings as far as the SLB and HPT are concerned, even though their Linux page tables would be separate. For mappings above 512TB, which use the extended_id array, we neglected to allocate new context ids on fork, meaning the parent and child use the same ids and therefore share those mappings even though they're supposed to be separate. This can lead to the parent seeing writes done by the child, which is essentially memory corruption. There is an additional exposure which is that if the child process exits, all its context ids are freed, including the context ids that are still in use by the parent for mappings above 512TB. One or more of those ids can then be reallocated to a third process, that process can then read/write to the parent's mappings above 512TB. Additionally if the freed id is used for the third process's primary context id, then the parent is able to read/write to the third process's mappings *below* 512TB. All of these are fundamental failures to enforce separation between processes. The only mitigating factor is that the bug only occurs if a process creates mappings above 512TB, and most applications still do not create such mappings. Only machines using the hash page table MMU are affected, eg. PowerPC 970 (G5), PA6T, Power5/6/7/8/9. By default Power9 bare metal machines (powernv) use the Radix MMU and are not affected, unless the machine has been explicitly booted in HPT mode (using disable_radix on the kernel command line). KVM guests on Power9 may be affected if the host or guest is configured to use the HPT MMU. LPARs under PowerVM on Power9 are affected as they always use the HPT MMU. Kernels built with PAGE_SIZE=4K are not affected. The fix is relatively simple, we need to reallocate context ids for all extended mappings on fork. Fixes: f384796c ("powerpc/mm: Add support for handling > 512TB address in SLB miss") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
James Morse authored
commit 87d3aa28 upstream. When a new control group is created __init_one_rdt_domain() walks all the other closids to calculate the sets of used and unused bits. If it discovers a pseudo_locksetup group, it breaks out of the loop. This means any later closid doesn't get its used bits added to used_b. These bits will then get set in unused_b, and added to the new control group's configuration, even if they were marked as exclusive for a later closid. When encountering a pseudo_locksetup group, we should continue. This is because "a resource group enters 'pseudo-locked' mode after the schemata is written while the resource group is in 'pseudo-locksetup' mode." When we find a pseudo_locksetup group, its configuration is expected to be overwritten, we can skip it. Fixes: dfe9674b ("x86/intel_rdt: Enable entering of pseudo-locksetup mode") Signed-off-by:
James Morse <james.morse@arm.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
Reinette Chatre <reinette.chatre@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H Peter Avin <hpa@zytor.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20190603172531.178830-1-james.morse@arm.com [Dropped comment due to lack of space] Signed-off-by:
-
Jouni Malinen authored
commit a71fd9da upstream. ieee80211_aes_gmac() uses the mic argument directly in sg_set_buf() and that does not allow use of stack memory (e.g., BUG_ON() is hit in sg_set_buf() with CONFIG_DEBUG_SG). BIP GMAC TX side is fine for this since it can use the skb data buffer, but the RX side was using a stack variable for deriving the local MIC value to compare against the received one. Fix this by allocating heap memory for the mic buffer. This was found with hwsim test case ap_cipher_bip_gmac_128 hitting that BUG_ON() and kernel panic. Cc: stable@vger.kernel.org Signed-off-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Andy Strohman authored
commit f77bf486 upstream. When dumping stations, memory allocated for station_info's pertid member will leak if the nl80211 header cannot be added to the sk_buff due to insufficient tail room. I noticed this leak in the kmalloc-2048 cache. Cc: stable@vger.kernel.org Fixes: 8689c051 ("cfg80211: dynamically allocate per-tid stats for station info") Signed-off-by:
Andy Strohman <andy@uplevelsystems.com> Signed-off-by:
-
Yu Wang authored
commit 79c92ca4 upstream. When receiving a deauthentication/disassociation frame from a TDLS peer, a station should not disconnect the current AP, but only disable the current TDLS link if it's enabled. Without this change, a TDLS issue can be reproduced by following the steps as below: 1. STA-1 and STA-2 are connected to AP, bidirection traffic is running between STA-1 and STA-2. 2. Set up TDLS link between STA-1 and STA-2, stay for a while, then teardown TDLS link. 3. Repeat step #2 and monitor the connection between STA and AP. During the test, one STA may send a deauthentication/disassociation frame to another, after TDLS teardown, with reason code 6/7, which means: Class 2/3 frame received from nonassociated STA. On receive this frame, the receiver STA will disconnect the current AP and then reconnect. It's not a expected behavior, purpose of this frame should be disabling the TDLS link, not the link with AP. Cc: stable@vger.kernel.org Signed-off-by:
Yu Wang <yyuwang@codeaurora.org> Signed-off-by:
-
Manikanta Pubbisetty authored
commit 33d915d9 upstream. As per the current design, in the case of sw crypto controlled devices, it is the device which advertises the support for AP/VLAN iftype based on it's ability to tranmsit packets encrypted in software (In VLAN functionality, group traffic generated for a specific VLAN group is always encrypted in software). Commit db3bdcb9 ("mac80211: allow AP_VLAN operation on crypto controlled devices") has introduced this change. Since 4addr AP operation also uses AP/VLAN iftype, this conditional way of advertising AP/VLAN support has broken 4addr AP mode operation on crypto controlled devices which do not support VLAN functionality. In the case of ath10k driver, not all firmwares have support for VLAN functionality but all can support 4addr AP operation. Because AP/VLAN support is not advertised for these devices, 4addr AP operations are also blocked. Fix this by allowing 4addr operation on devices which do not support AP/VLAN iftype but can support 4addr AP operation (decision is based on the wiphy flag WIPHY_FLAG_4ADDR_AP). Cc: stable@vger.kernel.org Fixes: db3bdcb9 ("mac80211: allow AP_VLAN operation on crypto controlled devices") Signed-off-by:
Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by:
-
Johannes Berg authored
commit 588f7d39 upstream. When receiving a robust management frame, drop it if we don't have rx->sta since then we don't have a security association and thus couldn't possibly validate the frame. Cc: stable@vger.kernel.org Signed-off-by:
-
Eric Biggers authored
commit 4f488fbc upstream. In wiphy_new_nm(), if an error occurs after dev_set_name() and device_initialize() have already been called, it's necessary to call put_device() (via wiphy_free()) to avoid a memory leak. Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com Fixes: 1f87f7d3 ("cfg80211: add rfkill support") Cc: stable@vger.kernel.org Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Christian Brauner authored
commit d728cf79 upstream. When propagating mounts across mount namespaces owned by different user namespaces it is not possible anymore to move or umount the mount in the less privileged mount namespace. Here is a reproducer: sudo mount -t tmpfs tmpfs /mnt sudo --make-rshared /mnt # create unprivileged user + mount namespace and preserve propagation unshare -U -m --map-root --propagation=unchanged # now change back to the original mount namespace in another terminal: sudo mkdir /mnt/aaa sudo mount -t tmpfs tmpfs /mnt/aaa # now in the unprivileged user + mount namespace mount --move /mnt/aaa /opt Unfortunately, this is a pretty big deal for userspace since this is e.g. used to inject mounts into running unprivileged containers. So this regression really needs to go away rather quickly. The problem is that a recent change falsely locked the root of the newly added mounts by setting MNT_LOCKED. Fix this by only locking the mounts on copy_mnt_ns() and not when adding a new mount. Fixes: 3bd045cc ("separate copying and locking mount tree on cross-userns copies") Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Tested-by:
Christian Brauner <christian@brauner.io> Acked-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Andy Lutomirski authored
commit ff17bbe0 upstream. GCC 5.5.0 sometimes cleverly hoists reads of the pvclock and/or hvclock pages before the vclock mode checks. This creates a path through vclock_gettime() in which no vclock is enabled at all (due to disabled TSC on old CPUs, for example) but the pvclock or hvclock page nevertheless read. This will segfault on bare metal. This fixes commit 459e3a21 ("gcc-9: properly declare the {pv,hv}clock_page storage") in the sense that, before that commit, GCC didn't seem to generate the offending code. There was nothing wrong with that commit per se, and -stable maintainers should backport this to all supported kernels regardless of whether the offending commit was present, since the same crash could just as easily be triggered by the phase of the moon. On GCC 9.1.1, this doesn't seem to affect the generated code at all, so I'm not too concerned about performance regressions from this fix. Cc: stable@vger.kernel.org Cc: x86@kernel.org Cc: Borislav Petkov <bp@alien8.de> Reported-by:
Duncan Roe <duncan_roe@optusnet.com.au> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Signed-off-by:
-
Steve French authored
commit 8d526d62 upstream. Some servers such as Windows 10 will return STATUS_INSUFFICIENT_RESOURCES as the number of simultaneous SMB3 requests grows (even though the client has sufficient credits). Return EAGAIN on STATUS_INSUFFICIENT_RESOURCES so that we can retry writes which fail with this status code. This (for example) fixes large file copies to Windows 10 on fast networks. Signed-off-by:
Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by:
Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
-
Marcel Holtmann authored
commit 693cd8ce upstream. When trying to align the minimum encryption key size requirement for Bluetooth connections, it turns out doing this in a central location in the HCI connection handling code is not possible. Original Bluetooth version up to 2.0 used a security model where the L2CAP service would enforce authentication and encryption. Starting with Bluetooth 2.1 and Secure Simple Pairing that model has changed into that the connection initiator is responsible for providing an encrypted ACL link before any L2CAP communication can happen. Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and before devices are causing a regression. The encryption key size check needs to be moved out of the HCI connection handling into the L2CAP channel setup. To achieve this, the current check inside hci_conn_security() has been moved into l2cap_check_enc_key_size() helper function and then called from four decisions point inside L2CAP to cover all combinations of Secure Simple Pairing enabled devices and device using legacy pairing and legacy service security model. Fixes: d5bb334a ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections") Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Marcel Holtmann authored
commit d5bb334a upstream. The minimum encryption key size for LE connections is 56 bits and to align LE with BR/EDR, enforce 56 bits of minimum encryption key size for BR/EDR connections as well. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Gao Xiang authored
commit 5efe5137 upstream. There are some backward incompatible features pending for months, mainly due to on-disk format expensions. However, we should ensure that it cannot be mounted with old kernels. Otherwise, it will causes unexpected behaviors. Fixes: ba2b77a8 ("staging: erofs: add super block operations") Cc: <stable@vger.kernel.org> # 4.19+ Reviewed-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
Gao Xiang <gaoxiang25@huawei.com> Signed-off-by:
-
Todd Kjos authored
commit a370003c upstream. There is a race between the binder driver cleaning up a completed transaction via binder_free_transaction() and a user calling binder_ioctl(BC_FREE_BUFFER) to release a buffer. It doesn't matter which is first but they need to be protected against running concurrently which can result in a UAF. Signed-off-by:
Todd Kjos <tkjos@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Ville Syrjälä authored
commit 475df5d0 upstream. We're now calling intel_pipe_config_compare(..., true) uncoditionally which means we're always going clobber the calculated M/N values with the old values if the fuzzy M/N check passes. That causes problems because the fuzzy check allows for a huge difference in the values. I'm actually tempted to just make the M/N checks exact, but that might prevent fastboot from kicking in when people want it. So for now let's overwrite the computed values with the old values only if decide to skip the modeset. v2: Copy has_drrs along with M/N M2/N2 values Cc: stable@vger.kernel.org Cc: Blubberbub@protonmail.com Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Tested-by: Blubberbub@protonmail.com Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110782 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110675 Fixes: d19f958d ("drm/i915: Enable fastset for non-boot modesets.") Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190619120929.4057-1-ville.syrjala@linux.intel.comSigned-off-by:
-
Thomas Hellstrom authored
commit cc0ba0d8 upstream. The HB port may not be available for various reasons. Either it has been disabled by a config option or by the hypervisor for other reasons. In that case, make sure we have a backup plan and use the backdoor port instead with a performance penalty. Cc: stable@vger.kernel.org Fixes: 89da76fd ("drm/vmwgfx: Add VMWare host messaging capability") Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Deepak Rawat <drawat@vmware.com> Signed-off-by:
-
Amir Goldstein authored
commit 6dde1e42 upstream. Relax the condition that overlayfs supports nfs export, to require that i_ino is consistent with st_ino/d_ino. It is enough to require that st_ino and d_ino are consistent. This fixes the failure of xfstest generic/504, due to mismatch of st_ino to inode number in the output of /proc/locks. Fixes: 12574a9f ("ovl: consistent i_ino for non-samefs with xino") Cc: <stable@vger.kernel.org> # v4.19 Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Sean Christopherson authored
commit b6b80c78 upstream. SVM's Nested Page Tables (NPT) reuses x86 paging for the host-controlled page walk. For 32-bit KVM, this means PAE paging is used even when TDP is enabled, i.e. the PAE root array needs to be allocated. Fixes: ee6268ba ("KVM: x86: Skip pae_root shadow allocation if tdp enabled") Cc: stable@vger.kernel.org Reported-by:
Jiri Palecek <jpalecek@web.de> Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Anisse Astier authored
commit adeaa21a upstream. Fix ssbd.c which depends implicitly on asm/ptrace.h including linux/prctl.h (through for example linux/compat.h, then linux/time.h, linux/seqlock.h, linux/spinlock.h and linux/irqflags.h), and uses PR_SPEC* defines. This is an issue since we'll soon be removing the include from asm/ptrace.h. Fixes: 9cdc0108 ("arm64: ssbd: Add prctl interface for per-thread mitigation") Cc: stable@vger.kernel.org Signed-off-by:
Anisse Astier <aastier@freebox.fr> Signed-off-by:
-
Anisse Astier authored
commit 35341ca0 upstream. Pulling linux/prctl.h into asm/ptrace.h in the arm64 UAPI headers causes userspace build issues for any program (e.g. strace and qemu) that includes both <sys/prctl.h> and <linux/ptrace.h> when using musl libc: | error: redefinition of 'struct prctl_mm_map' | struct prctl_mm_map { See https://github.com/foundriesio/meta-lmp/commit/6d4a106e191b5d79c41b9ac78fd321316d3013c0 for a public example of people working around this issue. Although it's a bit grotty, fix this breakage by duplicating the prctl constant definitions. Since these are part of the kernel ABI, they cannot be changed in future and so it's not the end of the world to have them open-coded. Fixes: 43d4da2c ("arm64/sve: ptrace and ELF coredump support") Cc: stable@vger.kernel.org Acked-by:
-
Faiz Abbas authored
commit 88a74841 upstream. If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Since am571x-, am572x- and am574x-idk don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). Cc: <stable@vger.kernel.org> Signed-off-by:
Faiz Abbas <faiz_abbas@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Faiz Abbas authored
commit c3c0b70c upstream. Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest dra76x data manual[1]. The new iodelay values will have better marginality and should prevent issues in corner cases. Also this particular pinctrl-array is using spaces instead of tabs for spacing between the values and the comments. Fix this as well. [1] http://www.ti.com/lit/ds/symlink/dra76p.pdf Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jan Kundrát authored
commit cc538ca4 upstream. Compared to kernel 5.0, patches merged for 5.1 added support for A38x' PHY guarded by a config option which was not enabled by default. As a result, there was no eth1 and eth2 on a Solid Run Clearfog Base. Ensure that A38x PHY is enabled on mvebu. [gregory: issue appeared in 5.1 not in 5.2 and added Fixes tag] Signed-off-by:
Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: David S. Miller <davem@davemloft.net> Cc: Maxime Chevallier <maxime.chevallier@bootlin.com> Fixes: a10c1c81 ("net: marvell: neta: add comphy support") Cc: stable@kernel.org Signed-off-by:
Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by:
-
Fabio Estevam authored
commit b25af2ff upstream. Since commit 1e434b70 ("ARM: imx: update the cpu power up timing setting on i.mx6sx") some characters loss is noticed on i.MX6ULL UART as reported by Christoph Niedermaier. The intention of such commit was to increase the SW2ISO field for i.MX6SX only, but since cpuidle-imx6sx is also used on i.MX6UL/i.MX6ULL this caused unintended side effects on other SoCs. Fix this problem by keeping the original SW2ISO value for i.MX6UL/i.MX6ULL and only increase SW2ISO in the i.MX6SX case. Cc: stable@vger.kernel.org Fixes: 1e434b70 ("ARM: imx: update the cpu power up timing setting on i.mx6sx") Reported-by:
Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by:
Fabio Estevam <festevam@gmail.com> Tested-by:
Sébastien Szymanski <sebastien.szymanski@armadeus.com> Tested-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Naveen N. Rao authored
commit 758f2046 upstream. BPF_ALU64 div/mod operations are currently using signed division, unlike BPF_ALU32 operations. Fix the same. DIV64 and MOD64 overflow tests pass with this fix. Fixes: 156d0e29 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
ShihPo Hung authored
commit bf587caa upstream. Because RISC-V compliant implementations can cache invalid entries in TLB, an SFENCE.VMA is necessary after changes to the page table. This patch adds an SFENCE.vma for the vmalloc_fault path. Signed-off-by:
ShihPo Hung <shihpo.hung@sifive.com> [paul.walmsley@sifive.com: reversed tab->whitespace conversion, wrapped comment lines] Signed-off-by:
Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: linux-riscv@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by:
-
