From Stephen Warren:
* tegra/dt:
  ARM: tegra: Use symbolic names for gr3d clocks
  ARM: tegra: Mark Tegra30 display controller compatible with Tegra20
  ARM: tegra: add GPIO controller to tegra124.dtsi
  ARM: tegra: enable LP1 suspend mode for Venice2
  ARM: tegra: enable Tegra RTC as default for Tegra124
  ARM: tegra: add Venice2 board support
  ARM: tegra: Add initial device tree for Tegra124
  ARM: tegra: add vcc supply for nct1008 to Cardhu
  ARM: tegra: add DT entry for nct1008 to Dalmore
  ARM: tegra: use dt-binding header for key code
  ARM: tegra: add palmas pincontrol to Dalmore device tree
Signed-off-by: Kevin Hilman <khilman@linaro.org>

From Jason Cooper:
mvebu dt changes for v3.13 (round 3)

 - dove
    - add audio devices
    - fix bad properties of si5351 clkout2 for CuBox

* tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu:
  ARM: Dove: fix bad properties of the si5351 clkout2 used by Cubox audio
  ARM: Dove: Add the audio device to the Cubox DT
  ARM: Dove: Add the audio devices in DT

Commit 05849c93 (ARM: tegra30: convert
device tree files to use CLK defines) updated the Tegra30 device tree to
use symbolic clock names but forgot to update this node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The display controller found on Tegra30 SoCs is backwards-compatible
with the one on Tegra20 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Tegra124 GPIO controller is identical to Tegra30, so copy the
DT node from tegra30.dtsi to tegra124.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

Merge tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

From Tony Lindgren:
omap device tree related changes via Benoit Cousson <bcousson@baylibre.com>:

Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk

* tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (58 commits)
  ARM: dts: dra7-evm: Add mmc2 node for eMMC support
  ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
  ARM: dts: omap5-uevm: mark TWL6037 as system-power-controller
  ARM: dts: omap3-igep0020: use standard constant for IRQ flags
  ARM: dts: omap3-igep0020: Add HS USB Host support
  ARM: dts: omap3-igep: Add USB OTG support
  ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable display
  ARM: dts: AM33XX: Add LCDC info into am335x-evm
  ARM: dts: AM437X: Add DES node
  ARM: dts: AM437X: Add AES node
  ARM: dts: AM33XX: Fix AES interrupt number
  ARM: dts: AM33XX: Add AES data and documentation
  ARM: dts: AM33XX: Add SHAM data and documentation
  ARM: dts: OMAP4: Add DES3DES node
  ARM: dts: OMAP4: Add AES node
  ARM: dts: am335x-evm[sdk]: switch mmc1 to 4-bit mode
  ARM: dts: am335x-bone-common: correct mux mode for cmd line
  ARM: dts: AM33XX: Add support for IGEP AQUILA EXPANSION board.
  ARM: dts: AM33XX: Add support for IGEP COM AQUILA
  ARM: dts: am335x-boneblack: move fixed regulator to board level
  ...
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:

- Always build in board-generic, and add pdata quirks and auxdata
  support for it so we have all the pdata related quirks
  in the same place.

- Merge of the drivers/pinctrl changes that are needed for PM
  to continue working on omap3 and also needed for other omaps
  eventually. The three pinctrl related patches have been acked
  by Linus Walleij and are pulled into both the pinctrl tree
  and this branch.

- Few defconfig related changes for drivers needed.

* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
  ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
  ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
  ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
  ARM: OMAP2+: Add minimal 8250 support for GPMC
  ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
  ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
  ARM: OMAP2+: Add support for auxdata
  pinctrl: single: Add support for auxdata
  pinctrl: single: Add support for wake-up interrupts
  pinctrl: single: Prepare for supporting SoC specific features
  ARM: OMAP2+: igep0020: use display init from dss-common
  ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
  +Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Merge tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next into next/dt

From Dinh Nguyen:
Updates to dts file structure for Altera's SOCFPGA

* Does not include any new bindings or bindings change
* Add dts file for a SOCFPGA with an Arria V FPGA
* Add a clocks property for the TWD timer
* Add support for Terasic SocKit Board which has Cyclone5 FPGA
* From Steffen Trumtrar:
"This series includes some minor cleanups (indentation and clock labels) and
reorders the socfpga dts hierarchy from:
	socfpga.dtsi
	-> socfpga_$board.dts
	-> socfpga_$otherboard.dts
to
	socfpga.dtsi
	-> socfpga_cyclone5.dtsi
	--> socfpga_cyclone5_$board.dts
	--> socfpga_cyclone5_$otherboard.dts
"

* tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next:
  dts: socfpga: Add support for Altera's SOCFPGA Arria V board
  ARM: socfpga: dts: fix s2f_* clock name
  ARM: socfpga: dts: cleanup indentation
  ARM: socfpga: dts: Add support for terasic SoCkit
  ARM: socfpga: dts: Move common nodes to cyclone5 dtsi
  arm: socfpga: Add clock for smp_twd timer
Signed-off-by: Kevin Hilman <khilman@linaro.org>

From Simon Horman:
* renesas/dt2: (21 commits)
  ARM: shmobile: bockw: fixup ether node naming
  ARM: shmobile: r8a7779: add irqpin default status on DTSI
  ARM: shmobile: marzen: fixup SMSC IRQ number on DTS
  ARM: shmobile: bockw: add SMSC support on DTS
  ARM: shmobile: r8a7778: add renesas_intc_irqpin support on DTSI
  ARM: shmobile: r8a7791 SMP device tree node
  ARM: shmobile: r8a7791 Arch timer device tree node
  ARM: shmobile: r8a7791 IRQC device tree node
  ARM: shmobile: armadillo800eva-reference: add SDHI and MMCIF interfaces
  ARM: shmobile: armadillo-reference: Add PWM backlight node to DT
  ARM: shmobile: r8a73a4: add a DT node for the DMAC
  ARM: shmobile: r8a7790: add I2C DT nodes
  ARM: shmobile: only enable used I2C interfaces in DT on all Renesas boards
  ARM: shmobile: r8a7778: add usb phy power control function
  ARM: shmobile: r8a7778: add USBHS clock
  ARM: shmobile: r8a7791 CMT support
  ARM: shmobile: r8a7791 SCIF support
  ARM: shmobile: Initial r8a7791 SoC support
  ARM: shmobile: r8a7778: add SSI/SRU clock support
  ARM: shmobile: r8a7790: Add DU and LVDS clocks
  ...
Signed-off-by: Kevin Hilman <khilman@linaro.org>

DWC3 enables USB3 functionality for OMAP5 boards,
it's safe to enable those drivers in omap2plus_defconfig.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
[tony@atomide.com: updated against other defconfig changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'for_3.13/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt

Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk

Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This allows the palmas pm_power_off to kick in on power off command
and switch off the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added
constants for IRQ edge/level triggered types so use it instead of
a magic number to enhance the DT readability.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Commit ad871c10 ("ARM: dts: OMAP: Add usb_otg and glue data to O
added USB OTG support for most OMAP boards but some OMAP3 boards
such as IGEP boards were not updated. This patch adds an USB OTG
device node to these board.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Enable the hdmi output and the LCD Controller on BeagleBone
Black. Also configure the correct pinmux for output of
video data from the SoC to the HDMI encoder.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm

Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AM437x SoC has a DES3DES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AM437x SoC has AES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AES interrupts were previously not used, but after recent changes
to omap-aes driver, its being used.
Correct the interrupt number to have working PIO mode.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms.  Also add Documentation file describing the data
for the AES module.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms.  Also add Documentation file describing the data
for the SHAM module.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

OMAP4 has an DES3DES  module that uses the omap-des crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set bus-width to make SD card operate in 4 bit mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.

The board adds the following connectivity:

    o USB OTG
    o USB HOST
    o HDMI
    o Ethernet
    o Serial Debug (3.3V)
    o 2x46 pin headers
    o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:

   o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
   o Cortex-A8 ARM CPU
   o 3.3 volts Inputs / Outputs use industrial
   o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
   o MicroSD card reader on-board
   o Ethernet controller on-board
   o JTAG debug connector available
   o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.

Move the fixed regulator to be at root of platform.

Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.

We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.

Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add DT nodes for TPS659038 PMIC on DRA7 boards.

It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.

Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt

Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.

Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>