- 03 Jan, 2013 18 commits
-
-
David Milburn authored
commit b03e66a6 upstream. If kdump is triggered with pending IO, controller may not respond causing kdump to fail. http://marc.info/?l=linux-ide&m=133032255424658&w=2 During error recovery ata_do_dev_read_id never completes due hang in mmio_insw. ata_do_dev_read_id ata_sff_data_xfer ioread16_rep mmio_insw if DMA start bit is cleared before reset, PIO command is successful and kdump succeeds. Signed-off-by:
David Milburn <dmilburn@redhat.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Paul Walmsley authored
commit 39141ddf upstream. After commit 846a1368 ("ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board started crashing during boot with omap2plus_defconfig: [ 3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB [ 3.915954] mmcblk0: p1 [ 4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM [ 4.093719] Modules linked in: [ 4.096954] CPU: 0 Not tainted (3.6.0-02232-g759e00b8 #570) [ 4.103149] PC is at vfp_reload_hw+0x1c/0x44 [ 4.107666] LR is at __und_usr_fault_32+0x0/0x8 It turns out that the context save/restore fix unmasked a latent bug in commit 5aaf2544 ("ARM: 6203/1: Make VFPv3 usable on ARMv6"). When CONFIG_VFPv3 is set, but the kernel is booted on a pre-VFPv3 core, the code attempts to save and restore the d16-d31 VFP registers. These are only present on non-D16 VFPv3+, so this results in an undefined instruction exception. The code didn't crash before commit 846a1368 because the save and restore code was only touching d0-d15, present on all VFP. Fix by implementing a request from Russell King to add a new HWCAP flag that affirmatively indicates the presence of the d16-d31 registers: http://marc.info/?l=linux-arm-kernel&m=135013547905283&w=2 and some feedback from Måns to clarify the name of the HWCAP flag. Signed-off-by:
Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dave Martin <dave.martin@linaro.org> Cc: Måns Rullgård <mans.rullgard@linaro.org> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Kees Cook authored
commit 31fd84b9 upstream. The min/max call needed to have explicit types on some architectures (e.g. mn10300). Use clamp_t instead to avoid the warning: kernel/sys.c: In function 'override_release': kernel/sys.c:1287:10: warning: comparison of distinct pointer types lacks a cast [enabled by default] Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Guenter Roeck authored
commit 1102dcab upstream. TjMax for the CE4100 series of Atom CPUs was previously reported to be 110 degrees C. cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170, reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz" with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants to the tjmax table. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Guenter Roeck authored
commit 41e58a1f upstream. Atom CPUs don't have a register to retrieve TjMax. Detection so far was incomplete. Use the X86 model ID to improve it. Signed-off-by:
-
Guenter Roeck authored
commit 5592906f upstream. Document the Atom series D2000 and N2000 (Cedar Trail) as being supported. List and set TjMax for those series. Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: "R, Durgadoss" <durgadoss.r@intel.com> Signed-off-by:
-
Jean Delvare authored
commit fcc14ac1 upstream. Document the new Atom series (Tunnel Creek and Medfield) as being supported, and list TjMax for the Atom E600 series. Also enable the Atom tjmax heuristic for these Atom CPU models. Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Cc: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: "R, Durgadoss" <durgadoss.r@intel.com> Signed-off-by:
-
Tejun Heo authored
commit fc4b514f upstream. 8852aac2 ("workqueue: mod_delayed_work_on() shouldn't queue timer on 0 delay") unexpectedly uncovered a very nasty abuse of delayed_work in megaraid - it allocated work_struct, casted it to delayed_work and then pass that into queue_delayed_work(). Previously, this was okay because 0 @delay short-circuited to queue_work() before doing anything with delayed_work. 8852aac2 moved 0 @delay test into __queue_delayed_work() after sanity check on delayed_work making megaraid trigger BUG_ON(). Although megaraid is already fixed by c1d390d8 ("megaraid: fix BUG_ON() from incorrect use of delayed work"), this patch converts BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s so that such abusers, if there are more, trigger warning but don't crash the machine. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Xiaotian Feng <xtfeng@gmail.com> [Shuah Khan: This change is back-ported from upstream change that converted BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s.] Tested on Stable Trees: 3.0.x, 3.4.x, 3.6.x Signed-off-by:
Shuah Khan <shuah.khan@hp.com> Signed-off-by:
-
Alan Cox authored
commit 879dca01 upstream. We handle NOTIFY_THROTTLING so don't then fall through to unsupported event. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Chris Wilson authored
commit c31407a3 upstream. Reported-and-tested-by:
Francois Tigeot <ftigeot@wolfpond.org> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55375Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Calvin Walton authored
commit a51d4ed0 upstream. This board is incorrectly detected as having an LVDS connector, resulting in the VGA output (the only available output on the board) showing the console only in the top-left 1024x768 pixels, and an extra LVDS connector appearing in X. It's a desktop Mini-ITX board using an Atom D525 CPU with an NM10 chipset. I've had this board for about a year, but this is the first time I noticed the issue because I've been running it headless for most of its life. Signed-off-by:
Calvin Walton <calvin.walton@kepstin.ca> Signed-off-by:
-
Wu Fengguang authored
commit 6edc59e6 upstream. [the order sorted by tiwai] Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Eugeni Dodonov authored
commit 9292f37e upstream. This allows to avoid talking to a non-responding bus repeatedly until we finally timeout after 15 attempts. We can do this by catching the -ENXIO error, provided by i2c_algo_bit:bit_doAddress call. Within the bit_doAddress we already try 3 times to get the edid data, so if the routine tells us that bus is not responding, it is mostly pointless to keep re-trying those attempts over and over again until we reach final number of retries. This change should fix https://bugs.freedesktop.org/show_bug.cgi?id=41059 and improve overall edid detection timing by 10-30% in most cases, and by a much larger margin in case of phantom outputs (up to 30x in one worst case). Timing results for i915-powered machines for 'time xrandr' command: Machine 1: from 0.840s to 0.290s Machine 2: from 0.315s to 0.280s Machine 3: from +/- 4s to 0.184s Timing results for HD5770 with 'time xrandr' command: Machine 4: from 3.210s to 1.060s Reviewed-by:
Chris Wilson <chris@hchris-wilson.co.uk> Reviewed-by:
Keith Packard <keithp@keithp.com> Tested-by:
Sean Finney <seanius@seanius.net> Tested-by:
Soren Hansen <soren@linux2go.dk> Tested-by:
Hernando Torque <sirius@sonnenkinder.org> Tested-by:
Mike Lothian <mike@fireburn.co.uk> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41059Signed-off-by:
Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Seth Heasley authored
commit 8bc039a1 upstream. This patch adds the HD Audio DeviceIDs for the Intel Lynx Point PCH. Signed-off-by:
Seth Heasley <seth.heasley@intel.com> Signed-off-by:
-
Chase Douglas authored
commit 503f7d53 upstream. Signed-off-by:
Chase Douglas <chase.douglas@canonical.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Petr Matousek authored
commit 6d1068b3 upstream. On hosts without the XSAVE support unprivileged local user can trigger oops similar to the one below by setting X86_CR4_OSXSAVE bit in guest cr4 register using KVM_SET_SREGS ioctl and later issuing KVM_RUN ioctl. invalid opcode: 0000 [#2] SMP Modules linked in: tun ip6table_filter ip6_tables ebtable_nat ebtables ... Pid: 24935, comm: zoog_kvm_monito Tainted: G D 3.2.0-3-686-pae EIP: 0060:[<f8b9550c>] EFLAGS: 00210246 CPU: 0 EIP is at kvm_arch_vcpu_ioctl_run+0x92a/0xd13 [kvm] EAX: 00000001 EBX: 000f387e ECX: 00000000 EDX: 00000000 ESI: 00000000 EDI: 00000000 EBP: ef5a0060 ESP: d7c63e70 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process zoog_kvm_monito (pid: 24935, ti=d7c62000 task=ed84a0c0 task.ti=d7c62000) Stack: 00000001 f70a1200 f8b940a9 ef5a0060 00000000 00200202 f8769009 00000000 ef5a0060 000f387e eda5c020 8722f9c8 00015bae 00000000 ed84a0c0 ed84a0c0 c12bf02d 0000ae80 ef7f8740 fffffffb f359b740 ef5a0060 f8b85dc1 0000ae80 Call Trace: [<f8b940a9>] ? kvm_arch_vcpu_ioctl_set_sregs+0x2fe/0x308 [kvm] ... [<c12bfb44>] ? syscall_call+0x7/0xb Code: 89 e8 e8 14 ee ff ff ba 00 00 04 00 89 e8 e8 98 48 ff ff 85 c0 74 1e 83 7d 48 00 75 18 8b 85 08 07 00 00 31 c9 8b 95 0c 07 00 00 <0f> 01 d1 c7 45 48 01 00 00 00 c7 45 1c 01 00 00 00 0f ae f0 89 EIP: [<f8b9550c>] kvm_arch_vcpu_ioctl_run+0x92a/0xd13 [kvm] SS:ESP 0068:d7c63e70 QEMU first retrieves the supported features via KVM_GET_SUPPORTED_CPUID and then sets them later. So guest's X86_FEATURE_XSAVE should be masked out on hosts without X86_FEATURE_XSAVE, making kvm_set_cr4 with X86_CR4_OSXSAVE fail. Userspaces that allow specifying guest cpuid with X86_FEATURE_XSAVE even on hosts that do not support it, might be susceptible to this attack from inside the guest as well. Allow setting X86_CR4_OSXSAVE bit only if host has XSAVE support. Signed-off-by:
Petr Matousek <pmatouse@redhat.com> Signed-off-by:
Marcelo Tosatti <mtosatti@redhat.com> [bwh: Backported to 3.2: both functions are in arch/x86/kvm/x86.c] Signed-off-by:
-
Oleg Nesterov authored
This patch is only for pre-v3.3 stable trees which backported b40a7959 "freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD". v3.3+ doesn't need this fix. b40a7959 is the trivial bugfix, but unfortunately I forgot that until 34b087e4 "freezer: kill unused set_freezable_with_signal()" there were another only-for-kernel-threads flag, PF_FREEZER_NOSIG, which should be cleared as well. See https://bugs.launchpad.net/ubuntu/+source/v86d/+bug/1080530 The freezer fails because it expects that a PF_FREEZER_NOSIG task doesn't need a signal. Before b40a7959 it wrongly succeeds leaving the PF_NOFREEZE | PF_FREEZER_NOSIG task unfrozen. Reported-and-tested-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Oleg Nesterov <oleg@redhat.com> [bwh: Don't touch PF_FORKNOEXEC; it's cleared elsewhere] Signed-off-by:
-
Ben Hutchings authored
This reverts commit c5ee5868, which was commit 201e72ac upstream. Herton Ronaldo Krzesinski pointed out that the race condition this dealt with does not exist in 3.2.y. Signed-off-by:
-
- 06 Dec, 2012 22 commits
-
-
Ben Hutchings authored
-
Ben Hutchings authored
commit 23795e58 upstream. IVB Xeon currently shares the same parameters IVB client. For 3.2, add model number to the switch in intel_idle_probe(), as there is no device ID table. Signed-off-by:
-
Len Brown authored
commit 6edab08c upstream. From an OS point of view, IVB looks like SNB, but quicker. Signed-off-by:
Len Brown <len.brown@intel.com> [bwh: Backported to 3.2: add model number to the switch in intel_idle_probe(), as there is no device ID table] Signed-off-by:
-
Mike Galbraith authored
commit 412d32e6 upstream. A rescue thread exiting TASK_INTERRUPTIBLE can lead to a task scheduling off, never to be seen again. In the case where this occurred, an exiting thread hit reiserfs homebrew conditional resched while holding a mutex, bringing the box to its knees. PID: 18105 TASK: ffff8807fd412180 CPU: 5 COMMAND: "kdmflush" #0 [ffff8808157e7670] schedule at ffffffff8143f489 #1 [ffff8808157e77b8] reiserfs_get_block at ffffffffa038ab2d [reiserfs] #2 [ffff8808157e79a8] __block_write_begin at ffffffff8117fb14 #3 [ffff8808157e7a98] reiserfs_write_begin at ffffffffa0388695 [reiserfs] #4 [ffff8808157e7ad8] generic_perform_write at ffffffff810ee9e2 #5 [ffff8808157e7b58] generic_file_buffered_write at ffffffff810eeb41 #6 [ffff8808157e7ba8] __generic_file_aio_write at ffffffff810f1a3a #7 [ffff8808157e7c58] generic_file_aio_write at ffffffff810f1c88 #8 [ffff8808157e7cc8] do_sync_write at ffffffff8114f850 #9 [ffff8808157e7dd8] do_acct_process at ffffffff810a268f [exception RIP: kernel_thread_helper] RIP: ffffffff8144a5c0 RSP: ffff8808157e7f58 RFLAGS: 00000202 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8107af60 RDI: ffff8803ee491d18 RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 Signed-off-by:
Mike Galbraith <mgalbraith@suse.de> Signed-off-by:
-
Naoya Horiguchi authored
commit 783657a7 upstream. When we try to soft-offline a thp tail page, put_page() is called on the tail page unthinkingly and VM_BUG_ON is triggered in put_compound_page(). This patch splits thp before going into the main body of soft-offlining. Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Andi Kleen <andi.kleen@intel.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Johannes Weiner authored
commit 60cefed4 upstream. Kswapd does not in all places have the same criteria for a balanced zone. Zones are only being reclaimed when their high watermark is breached, but compaction checks loop over the zonelist again when the zone does not meet the low watermark plus two times the size of the allocation. This gets kswapd stuck in an endless loop over a small zone, like the DMA zone, where the high watermark is smaller than the compaction requirement. Add a function, zone_balanced(), that checks the watermark, and, for higher order allocations, if compaction has enough free memory. Then use it uniformly to check for balanced zones. This makes sure that when the compaction watermark is not met, at least reclaim happens and progress is made - or the zone is declared unreclaimable at some point and skipped entirely. Signed-off-by:
Johannes Weiner <hannes@cmpxchg.org> Reported-by:
George Spelvin <linux@horizon.com> Reported-by:
Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de> Reported-by:
Tomas Racek <tracek@redhat.com> Tested-by:
Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by:
-
Jianguo Wu authored
commit ae64ffca upstream. I enable CONFIG_DEBUG_VIRTUAL and CONFIG_SPARSEMEM_VMEMMAP, when doing memory hotremove, there is a kernel BUG at arch/x86/mm/physaddr.c:20. It is caused by free_section_usemap()->virt_to_page(), virt_to_page() is only used for kernel direct mapping address, but sparse-vmemmap uses vmemmap address, so it is going wrong here. ------------[ cut here ]------------ kernel BUG at arch/x86/mm/physaddr.c:20! invalid opcode: 0000 [#1] SMP Modules linked in: acpihp_drv acpihp_slot edd cpufreq_conservative cpufreq_userspace cpufreq_powersave acpi_cpufreq mperf fuse vfat fat loop dm_mod coretemp kvm crc32c_intel ipv6 ixgbe igb iTCO_wdt i7core_edac edac_core pcspkr iTCO_vendor_support ioatdma microcode joydev sr_mod i2c_i801 dca lpc_ich mfd_core mdio tpm_tis i2c_core hid_generic tpm cdrom sg tpm_bios rtc_cmos button ext3 jbd mbcache usbhid hid uhci_hcd ehci_hcd usbcore usb_common sd_mod crc_t10dif processor thermal_sys hwmon scsi_dh_alua scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic ata_piix libata megaraid_sas scsi_mod CPU 39 Pid: 6454, comm: sh Not tainted 3.7.0-rc1-acpihp-final+ #45 QCI QSSC-S4R/QSSC-S4R RIP: 0010:[<ffffffff8103c908>] [<ffffffff8103c908>] __phys_addr+0x88/0x90 RSP: 0018:ffff8804440d7c08 EFLAGS: 00010006 RAX: 0000000000000006 RBX: ffffea0012000000 RCX: 000000000000002c ... Signed-off-by:
Jianguo Wu <wujianguo@huawei.com> Signed-off-by:
Jiang Liu <jiang.liu@huawei.com> Reviewd-by:
Wen Congyang <wency@cn.fujitsu.com> Acked-by:
Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reviewed-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Darren Hart authored
commit aa10990e upstream. Dave Jones reported a bug with futex_lock_pi() that his trinity test exposed. Sometime between queue_me() and taking the q.lock_ptr, the lock_ptr became NULL, resulting in a crash. While futex_wake() is careful to not call wake_futex() on futex_q's with a pi_state or an rt_waiter (which are either waiting for a futex_unlock_pi() or a PI futex_requeue()), futex_wake_op() and futex_requeue() do not perform the same test. Update futex_wake_op() and futex_requeue() to test for q.pi_state and q.rt_waiter and abort with -EINVAL if detected. To ensure any future breakage is caught, add a WARN() to wake_futex() if the same condition is true. This fix has seen 3 hours of testing with "trinity -c futex" on an x86_64 VM with 4 CPUS. [akpm@linux-foundation.org: tidy up the WARN()] Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Reported-by:
Dave Jones <davej@redat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: John Kacur <jkacur@redhat.com> Signed-off-by:
-
Oliver Hartkopp authored
commit 81b40110 upstream. Set in the rx_ifindex to pass the correct interface index in the case of a message timeout detection. Usually the rx_ifindex value is set at receive time. But when no CAN frame has been received the RX_TIMEOUT notification did not contain a valid value. Reported-by:
Andre Naujoks <nautsch2@googlemail.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Jan Kara authored
commit 25389bb2 upstream. Commit 09e05d48 introduced a wait for transaction commit into journal_unmap_buffer() in the case we are truncating a buffer undergoing commit in the page stradding i_size on a filesystem with blocksize < pagesize. Sadly we forgot to drop buffer lock before waiting for transaction commit and thus deadlock is possible when kjournald wants to lock the buffer. Fix the problem by dropping the buffer lock before waiting for transaction commit. Since we are still holding page lock (and that is OK), buffer cannot disappear under us. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Roland Dreier authored
commit 893d290f upstream. After we've done __elv_add_request() and __blk_run_queue() in blk_execute_rq_nowait(), the request might finish and be freed immediately. Therefore checking if the type is REQ_TYPE_PM_RESUME isn't safe afterwards, because if it isn't, rq might be gone. Instead, check beforehand and stash the result in a temporary. This fixes crashes in blk_execute_rq_nowait() I get occasionally when running with lots of memory debugging options enabled -- I think this race is usually harmless because the window for rq to be reallocated is so small. Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Jens Axboe authored
commit a8c32a5c upstream. Request based dm attempts to re-run the request queue off the request completion path. If used with a driver that potentially does end_io from its request_fn, we could deadlock trying to recurse back into request dispatch. Fix this by punting the request queue run to kblockd. Tested to fix a quickly reproducible deadlock in such a scenario. Acked-by:
Alasdair G Kergon <agk@redhat.com> Signed-off-by:
-
Al Viro authored
commit 441a179d upstream. int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set, compat_sigset_t __user *oset, unsigned int sigsetsize) { sigset_t old_set, new_set; int ret; if (set && get_sigset32(set, &new_set, sigsetsize)) ... static int get_sigset32(compat_sigset_t __user *up, sigset_t *set, size_t sz) { compat_sigset_t s; int r; if (sz != sizeof *set) panic("put_sigset32()"); In other words, rt_sigprocmask(69, (void *)69, 69) done by 32bit process will promptly panic the box. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Jason Gunthorpe authored
commit 1dc831bf upstream. - The code relies on rc_pci_fixup being called, which only happens when CONFIG_PCI_QUIRKS is enabled, so add that to Kconfig. Omitting this causes a booting failure with a non-obvious cause. - Update rc_pci_fixup to set the class properly, copying the more modern style from other places - Correct the rc_pci_fixup comment Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Jason Cooper <jason@lakedaemon.net> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Russell King - ARM Linux authored
commit d356cf5a upstream. PMU interrupts start at IRQ_DOVE_PMU_START, not IRQ_DOVE_PMU_START + 1. Fix the condition. (It may have been less likely to occur had the code been written "if (irq >= IRQ_DOVE_PMU_START" which imho is the easier to understand notation, and matches the normal way of thinking about these things.) Signed-off-by:
-
Russell King - ARM Linux authored
commit 5d3df935 upstream. Fix the acknowledgement of PMU interrupts on Dove: some Dove hardware has not been sensibly designed so that interrupts can be handled in a race free manner. The PMU is one such instance. The pending (aka 'cause') register is a bunch of RW bits, meaning that these bits can be both cleared and set by software (confirmed on the Armada-510 on the cubox.) Hardware sets the appropriate bit when an interrupt is asserted, and software is required to clear the bits which are to be processed. If we write ~(1 << bit), then we end up asserting every other interrupt except the one we're processing. So, we need to do a read-modify-write cycle to clear the asserted bit. However, any interrupts which occur in the middle of this cycle will also be written back as zero, which will also clear the new interrupts. The upshot of this is: there is _no_ way to safely clear down interrupts in this register (and other similarly behaving interrupt pending registers on this device.) The patch below at least stops us creating new interrupts. Signed-off-by:
-
Dave Jones authored
commit 88a693b5 upstream. =============================== [ INFO: suspicious RCU usage. ] 3.5.0-rc1+ #63 Not tainted ------------------------------- security/selinux/netnode.c:178 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 1 lock held by trinity-child1/8750: #0: (sel_netnode_lock){+.....}, at: [<ffffffff812d8f8a>] sel_netnode_sid+0x16a/0x3e0 stack backtrace: Pid: 8750, comm: trinity-child1 Not tainted 3.5.0-rc1+ #63 Call Trace: [<ffffffff810cec2d>] lockdep_rcu_suspicious+0xfd/0x130 [<ffffffff812d91d1>] sel_netnode_sid+0x3b1/0x3e0 [<ffffffff812d8e20>] ? sel_netnode_find+0x1a0/0x1a0 [<ffffffff812d24a6>] selinux_socket_bind+0xf6/0x2c0 [<ffffffff810cd1dd>] ? trace_hardirqs_off+0xd/0x10 [<ffffffff810cdb55>] ? lock_release_holdtime.part.9+0x15/0x1a0 [<ffffffff81093841>] ? lock_hrtimer_base+0x31/0x60 [<ffffffff812c9536>] security_socket_bind+0x16/0x20 [<ffffffff815550ca>] sys_bind+0x7a/0x100 [<ffffffff816c03d5>] ? sysret_check+0x22/0x5d [<ffffffff810d392d>] ? trace_hardirqs_on_caller+0x10d/0x1a0 [<ffffffff8133b09e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff816c03a9>] system_call_fastpath+0x16/0x1b This patch below does what Paul McKenney suggested in the previous thread. Signed-off-by:
Dave Jones <davej@redhat.com> Reviewed-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by:
Paul Moore <paul@paul-moore.com> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
David Henningsson authored
commit af02dde8 upstream. We found a new codec ID 292, and that just a simple quirk would enable sound output/input on this ALC292 chip. BugLink: https://bugs.launchpad.net/bugs/1081466Tested-by:
Acelan Kao <acelan.kao@canonical.com> Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Kailang Yang authored
commit 7ff34ad8 upstream. These are compatible with standard ALC269 parser. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Boris Ostrovsky authored
commit 36c46ca4 upstream. Add valid patch size for family 16h processors. [ hpa: promoting to urgent/stable since it is hw enabling and trivial ] Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@amd.com> Acked-by:
Andreas Herrmann <herrmann.der.user@googlemail.com> Link: http://lkml.kernel.org/r/1353004910-2204-1-git-send-email-boris.ostrovsky@amd.comSigned-off-by:
H. Peter Anvin <hpa@linux.intel.com> Signed-off-by:
-
H. Peter Anvin authored
commit cb57a2b4 upstream. Modules, in particular oprofile (and possibly other similar tools) need kernel_stack_pointer(), so export it using EXPORT_SYMBOL_GPL(). Cc: Yang Wei <wei.yang@windriver.com> Cc: Robert Richter <robert.richter@amd.com> Cc: Jun Zhang <jun.zhang@intel.com> Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.comSigned-off-by:
-
Robert Richter authored
commit 10226238 upstream. In 32 bit the stack address provided by kernel_stack_pointer() may point to an invalid range causing NULL pointer access or page faults while in NMI (see trace below). This happens if called in softirq context and if the stack is empty. The address at ®s->sp is then out of range. Fixing this by checking if regs and ®s->sp are in the same stack context. Otherwise return the previous stack pointer stored in struct thread_info. If that address is invalid too, return address of regs. BUG: unable to handle kernel NULL pointer dereference at 0000000a IP: [<c1004237>] print_context_stack+0x6e/0x8d *pde = 00000000 Oops: 0000 [#1] SMP Modules linked in: Pid: 4434, comm: perl Not tainted 3.6.0-rc3-oprofile-i386-standard-g4411a05 #4 Hewlett-Packard HP xw9400 Workstation/0A1Ch EIP: 0060:[<c1004237>] EFLAGS: 00010093 CPU: 0 EIP is at print_context_stack+0x6e/0x8d EAX: ffffe000 EBX: 0000000a ECX: f4435f94 EDX: 0000000a ESI: f4435f94 EDI: f4435f94 EBP: f5409ec0 ESP: f5409ea0 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 CR0: 8005003b CR2: 0000000a CR3: 34ac9000 CR4: 000007d0 DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000 DR6: ffff0ff0 DR7: 00000400 Process perl (pid: 4434, ti=f5408000 task=f5637850 task.ti=f4434000) Stack: 000003e8 ffffe000 00001ffc f4e39b00 00000000 0000000a f4435f94 c155198c f5409ef0 c1003723 c155198c f5409f04 00000000 f5409edc 00000000 00000000 f5409ee8 f4435f94 f5409fc4 00000001 f5409f1c c12dce1c 00000000 c155198c Call Trace: [<c1003723>] dump_trace+0x7b/0xa1 [<c12dce1c>] x86_backtrace+0x40/0x88 [<c12db712>] ? oprofile_add_sample+0x56/0x84 [<c12db731>] oprofile_add_sample+0x75/0x84 [<c12ddb5b>] op_amd_check_ctrs+0x46/0x260 [<c12dd40d>] profile_exceptions_notify+0x23/0x4c [<c1395034>] nmi_handle+0x31/0x4a [<c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45 [<c13950ed>] do_nmi+0xa0/0x2ff [<c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45 [<c13949e5>] nmi_stack_correct+0x28/0x2d [<c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45 [<c1003603>] ? do_softirq+0x4b/0x7f <IRQ> [<c102a06f>] irq_exit+0x35/0x5b [<c1018f56>] smp_apic_timer_interrupt+0x6c/0x7a [<c1394746>] apic_timer_interrupt+0x2a/0x30 Code: 89 fe eb 08 31 c9 8b 45 0c ff 55 ec 83 c3 04 83 7d 10 00 74 0c 3b 5d 10 73 26 3b 5d e4 73 0c eb 1f 3b 5d f0 76 1a 3b 5d e8 73 15 <8b> 13 89 d0 89 55 e0 e8 ad 42 03 00 85 c0 8b 55 e0 75 a6 eb cc EIP: [<c1004237>] print_context_stack+0x6e/0x8d SS:ESP 0068:f5409ea0 CR2: 000000000000000a ---[ end trace 62afee3481b00012 ]--- Kernel panic - not syncing: Fatal exception in interrupt V2: * add comments to kernel_stack_pointer() * always return a valid stack address by falling back to the address of regs Reported-by:
Yang Wei <wei.yang@windriver.com> Signed-off-by:
Robert Richter <robert.richter@amd.com> Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.comSigned-off-by:
-
