When clearing the chip-select mask, the controller will switch to chip
selecting the native CS0 line. Because the control register chip-select
mask is not updated in a single write this will cause undesirable
chip-selection of CS0 even when requesting to select other native
chip-select lines. This is additionally problematic as the chip-select
may still be asserted. With the ARMADA 38x SoC the controller will
assert both the desired native chip-select and CS0.

To avoid any undesirable behaviour with the chip-select lines, update
the control register with a single write. This avoids selecting CS0 and
causes the (de-)assert to apply at the same time.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20210816050228.3223661-1-nathan@nathanrossi.comSigned-off-by: Mark Brown <broonie@kernel.org>

buswidth and dtr fields in spi_mem_op are only valid when the
corresponding spi_mem_op phase has a non-zero length. For example,
SPI NAND core doesn't set buswidth when using SPI_MEM_OP_NO_ADDR
phase.

Fix the dtr checks in set_protocol() and suppports_mem_op() to
ignore empty spi_mem_op phases, as checking for dtr field in
empty phase will result in false negatives.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210716232504.182-3-a-nandan@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 3a70dd2d ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.

Remove the code trying to handle receive data before the transfer is
started to fix the problem.

Fixes: 3a70dd2d ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.netSigned-off-by: Mark Brown <broonie@kernel.org>

For (2 * 1000000) / min_speed_hz < 10 to be true in naturals with zero,
the min_speed_hz must be above 200000 (i.e. 200001 rounds down to 9, so
the condition triggers). Update the comment. No functional change.

Fixes: 6fd8b850 ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210727160428.7673-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

The spi_imx->spi_bus_clk may be uninitialized and thus also zero in
mx51_ecspi_prepare_message(), which would lead to division by zero
in kernel. Since bitbang .setup_transfer callback which initializes
the spi_imx->spi_bus_clk is called after bitbang prepare_message
callback, iterate over all the transfers in spi_message, find the
one with lowest bus frequency, and use that bus frequency for the
delay calculation.

Note that it is not possible to move this CONFIGREG delay back into
the .setup_transfer callback, because that is invoked too late, after
the GPIO chipselects were already configured.

Fixes: 135cbd37 ("spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210726100102.5188-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 3ce6c9e2 ("spi: add of_device_uevent_modalias support") is
incomplete, as it didn't update the modalias_show function to generate the
of: modalias string if available.

Fixes: 3ce6c9e2 ("spi: add of_device_uevent_modalias support")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmwnpi4fya.fsf@suse.deSigned-off-by: Mark Brown <broonie@kernel.org>

In meson_spicc_probe, the error handling code needs to clean up master
by calling spi_master_put, but the remove function does not have this
function call. This will lead to memory leak of spicc->master.
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: 454fa271("spi: Add Meson SPICC driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210720100116.1438974-1-mudongliangabcd@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

With the spi device table udev can autoload the spi-mux module in
the presence of an spi-mux device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210721095321.2165453-1-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The bcm2835_spi_transfer_one function can create a deadlock
if it is called while another thread already has the
CCF lock.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Fixes: f8043872 ("spi: add driver for BCM2835")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210716210245.13240-2-alexandru.tachici@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8 ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.

Undo 734882a8 ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.

Fixes: 734882a8 ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

cadence-quadspi has a builtin Auto-HW polling funtionality using which
it keep tracks of completion of write operations. When Auto-HW polling
is enabled, it automatically initiates status register read operation,
until the flash clears its busy bit.

cadence-quadspi controller doesn't allow an address phase when
auto-polling the busy bit on the status register. Unlike SPI NOR
flashes, SPI NAND flashes do require the address of status register
when polling the busy bit using the read register operation. As
Auto-HW polling is enabled by default, cadence-quadspi returns a
timeout for every write operation after an indefinite amount of
polling on SPI NAND flashes.

Disable Auto-HW polling completely as the spi-nor core, spinand core,
etc. take care of polling the busy bit on their own.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210713125743.1540-2-a-nandan@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix below division by zero warning:
- The reason for dividing by zero is because the dummy bus width is zero,
  but if the dummy n bytes is zero, it indicates that there is no data transfer,
  so we can just return zero without doing any calculations.

[    0.795337] Division by zero in kernel.
   :
[    0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[    0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)

Fixes: 7512eaf5 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/92eea403-9b21-2488-9cc1-664bee760c5e@nskint.co.jpSigned-off-by: Mark Brown <broonie@kernel.org>

Revert to change to a better code.

This reverts commit 55cef88b.
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Link: https://lore.kernel.org/r/bd30bdb4-07c4-f713-5648-01c898d51f1b@nskint.co.jpSigned-off-by: Mark Brown <broonie@kernel.org>

Fix below division by zero warning:
- Added an if statement because buswidth can be zero, resulting in division by zero.
- The modified code was based on another driver (atmel-quadspi).

[    0.795337] Division by zero in kernel.
   :
[    0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[    0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)

Fixes: 7512eaf5 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Link: https://lore.kernel.org/r/ed989af6-da88-4e0b-9ed8-126db6cad2e4@nskint.co.jpSigned-off-by: Mark Brown <broonie@kernel.org>

This patch move devm_spi_register_master to the end of mtk_spi_probe.
If slaves call spi_sync in there probe function, master should have probe done.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210713114247.1536-1-mason.zhang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

In FIFO mode were two problems:
- RX mode was never handled and
- in this case the tx_buf pointer was NULL and caused an exception

fix this by handling RX mode in mtk_spi_fifo_transfer

Fixes: a568231f ("spi: mediatek: Add spi bus for Mediatek MT8173")
Signed-off-by: Peter Hess <peter.hess@ph-home.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210706121609.680534-1-linux@fw-web.deSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 5fa5e6de ("spi: atmel: Switch to transfer_one transfer
method") switched to using transfer_one and set_cs.  The
core doesn't call set_cs when the chip select lines are gpios.  Add the
SPI_MASTER_GPIO_SS flag to the driver to ensure the calls to set_cs
happen since the driver programs configuration registers there.

Fixes: 5fa5e6de ("spi: atmel: Switch to transfer_one transfer method")
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210629192218.32125-1-dan.sneddon@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add pm_runtime calls in probe/probe error path and remove
in order to be consistent in all places in ordering and
ensure that pm_runtime is disabled prior to resources used
by the SPI controller.

This patch also fixes the 2 following warnings on driver remove:
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:594 clk_core_disable_lock+0x18/0x24
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:476 clk_unprepare+0x24/0x2c

Fixes: 038ac869 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-2-git-send-email-alain.volmat@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since 00b80ac9 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b850 ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.

Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.

Fixes: 00b80ac9 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

In case of Full-Duplex mode, DXP flag is set when RXP and TXP flags are
set. But to avoid 2 different handlings, just add TXP and RXP flag in
the mask instead of DXP, and then keep the initial handling of TXP and
RXP events.
Also rephrase comment about EOTIE which is one of the interrupt enable
bits. It is not triggered by any event.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/1625042723-661-3-git-send-email-alain.volmat@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some controllers like qcom geni need the parent device to be used for
dma mapping, so add a dma_map_dev field and let drivers fill this to be
used as mapping device
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210625052213.32260-4-vkoul@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert spi for Xilinx Zynq UltraScale+ MPSoC GQSPI bindings
documentation to YAML.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210613214317.296667-1-iwamatsu@nigauri.orgSigned-off-by: Mark Brown <broonie@kernel.org>

There is an assignment of ancillary->mode to itself which looks
dubious since the proceeding comment states that the speed and
mode is taken over from the SPI main device, indicating that
ancillary->mode should assigned using the value spi->mode.
Fix this.

Addresses-Coverity: ("Self assignment")
Fixes: 0c79378c ("spi: add ancillary device support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210623172300.161484-1-colin.king@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Changes in v10:
- The internal CS inactive function is only supported after VER 0x00110002

Changes in v9:
- Conver to use CS GPIO description

Changes in v8:
- There is a problem with the version 7 mail format. resend it

Changes in v7:
- Fall back "rockchip,rv1126-spi" to "rockchip,rk3066-spi"

Changes in v6:
- Consider to compatibility, the "rockchip,rk3568-spi" is removed in
  Series-changes v5, so the commit massage should also remove the
  corresponding information

Changes in v5:
- Change to leave one compatible id rv1126, and rk3568 is compatible
  with rv1126

Changes in v4:
- Adjust the order patches
- Simply commit massage like redundancy "application" content

Changes in v3:
- Fix compile error which is find by Sascha in [v2,2/8]

Jon Lin (6):
  dt-bindings: spi: spi-rockchip: add description for rv1126
  spi: rockchip: add compatible string for rv1126
  spi: rockchip: Set rx_fifo interrupt waterline base on transfer item
  spi: rockchip: Wait for STB status in slave mode tx_xfer
  spi: rockchip: Support cs-gpio
  spi: rockchip: Support SPI_CS_HIGH

 .../devicetree/bindings/spi/spi-rockchip.yaml |  1 +
 drivers/spi/spi-rockchip.c                    | 55 ++++++++++++++-----
 2 files changed, 41 insertions(+), 15 deletions(-)

--
2.17.1

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095843.3228-3-wsa+renesas@sang-engineering.comSigned-off-by: Mark Brown <broonie@kernel.org>

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095843.3228-2-wsa+renesas@sang-engineering.comSigned-off-by: Mark Brown <broonie@kernel.org>

The description below will be used for rv1126.dtsi or compatible one in
the future
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

1.Add standard spi-cs-high support
2.Refer to spi-controller.yaml for details
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104848.19539-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

1.Add standard cs-gpio support
2.Refer to spi-controller.yaml for details
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104848.19539-1-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

After ROCKCHIP_SPI_VER2_TYPE2, SR->STB is a more accurate judgment
bit for spi slave transmition.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-5-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The error here is to calculate the width as 8 bits. In fact, 16 bits
should be considered.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-4-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add compatible string for rv1126 for potential applications.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210621104800.19088-3-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add binding support for devices, that have more than one
chip select. A typical example are SPI connected microcontroller,
that can also be programmed over SPI like NXP Kinetis or
chips with a configuration and a data chip select, such as
Microchip's MRF89XA transceiver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-3-sebastian.reichel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Introduce support for ancillary devices, similar to existing
implementation for I2C. This is useful for devices having
multiple chip-selects, for example some microcontrollers
provide a normal SPI interface and a flashing SPI interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-2-sebastian.reichel@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert SPI for Xilinx bindings documentation to YAML schemas.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210605002931.858031-1-iwamatsu@nigauri.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert spi for Cadence SPI bindings documentation to YAML.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210605003811.858676-1-iwamatsu@nigauri.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Remove struct stm32_qspi_flash's field qspi which is not used.

Fixes: c530cd1d ("spi: spi-mem: add stm32 qspi controller")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210615090115.30702-1-patrice.chotard@foss.st.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add OF support as already done for ACPI to take driver
MODULE_DEVICE_TABLE(of, ..) into account.

For example with this change a spi nor device MODALIAS changes from:

MODALIAS=spi:spi-nor

to

MODALIAS=of:Nspi-flashT(null)Cjedec,spi-nor
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210525091003.18228-1-m.felsch@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

when meson_spicc_clk_init returns failed, it should goto the
out_clk label.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1623562156-21995-1-git-send-email-zpershuai@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

In meson_spifc_probe function, when enable the device pclk clock is
error, it should use clk_disable_unprepare to release the core clock.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1623562172-22056-1-git-send-email-zpershuai@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>