Add the host1x node along with its children to the Tegra20 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

TrimSlice contains a 1MiB SPI flash. Represent this in the device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Nvidia's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add DT entry for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: move sflash node to keep file sorted]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Harmony board has an ON Semiconductors NCT1008 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Tamonten SOM has an ON Semiconductor NCT1008 connected to the DVC
bus which is used to measure the ambient (local) temperature as well as
the on-die (remote) temperature.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Harmony board has an Analog Devices ADT7461 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

These properties are already set by the tegra20-tamonten.dtsi, so they
don't need to be repeated.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This commit allows the I2C2 controller on Tegra20 to be routed either to
the DDC or the PTA pin group at runtime. On Tamonten this allows the I2C
bus to be used for the DDC of the HDMI connector or to access I2C chips
on the carrier board.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.

SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add slink controller details in the dts file of
Tegra20 and Tegra30.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Tegra 2's I2C2 controller can be routed to either the PTA
or DDC pin group on Ventana. So:
- Remove the HDMI function definition of pta pingroup
- Define child i2c adapters(ddc & pta) for I2C2 controller
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Configure pinmux as required for WiFi.
Enable the SDHCI1 controller for a02 and a04 board, which is connected to the
WiFi module.
For now, always enable the regulator that provides power to the Wifi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Configure pinmux as required for WiFi.
Enable the SDHCI1 controller, which is connectted to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable the SDHCI1 controller. This is connected to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Setup the clock parents for the two display controllers and HDMI.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add the OF_DEV_AUXDATA table entries required to associate the proper
names with host1x and its children. In turn, this allows the devices to
find the required clocks.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Extend the pll_d frequency table with a few entries to support common
HDMI and LVDS display modes and setup the clock parents for the two
display controllers and HDMI.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add the OF_DEV_AUXDATA table entries required to associate the proper
names with host1x and its children. In turn, this allows the devices to
find the required clocks.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This patch adds speedo-based process identification support for Tegra30.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren s/Tegra3/Tegra30/ in log print,
s/T30/Tegra30/ in commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Detect CPU and core process ID by checking speedo corner tables.
This can provide a more accurate process ID.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren s/Tegra2/Tegra20/ in log print]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Change the spare fuse base from a definition to a variable.
It provides flexibilty to read spare fuse on different chip.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This patch implements ARM linux patch 6395/1 for Tegra. See commit
1a8e41cd "ARM: 6395/1: VExpress: Set bit 22 in the PL310 (cache
controller) AuxCtlr register" for details.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[swarren: added commit subject for referenced patch]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add OF_DEV_AUXDATA for sflash controller driver for Tegra20
board dt files.
Set the parent clock of sflash controller to PLLP and configure
clock to 20MHz.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable the data prefetch on L2. The bit28 in aux ctrl register.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>

Add OF_DEV_AUXDATA for slink driver for Tegra20 and Tegra30
board dt files.
Set the parent clock of slink controller to PLLP and configure
clock to 100MHz.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Moving L2 cache init to DT support.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add L2 cache controller binding into DT for Tegra.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Adding the AHB and APB bus clock for Tegra30.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Set up the wlan clock tree for Tegra20 and Tegra30.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Nothing outside mach-tegra uses this file, so there's no need for it to
be in <mach/>.

Since uncompress.h and debug-macro.S remain in include/mach, they need
to include "../../irammap.h" becaue of this change. Both these usages
will be removed shortly, when Tegra's DEBUG_LL implementation is updated
not to pass information through IRAM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Nothing outside mach-tegra uses this file, so there's no need for it to
be in <mach/>.

Since uncompress.h and debug-macro.S remain in include/mach, they need
to include "../../iomap.h" becaue of this change. uncompress.h will soon
be deleted in later multi-platform/single-zImage patches. debug-macro.S
will need to continue to include this header using an explicit relative
path, to avoid duplicating the physical->virtual address mapping that
iomap.h dictates.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Remove includes of <mach/dma.h> from sound/soc; nothing from it is used.

Remove include of <mach/dma.h> from mach-tegra/apbio.c; since the DMA
transfers made by this file don't need flow-control with any peripheral,
there's no need to set any slave ID.

Once those changes are made, there are no remaining users of <mach/dma.h>
so remove it. Drivers should get this information from device tree. This
removal is necessary for single zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We wish to empty arch/arm/mach-tegra/include/mach/ as much as possible
to enable single zImage. Move tegra-ahb.h to a more central location
(suggested by Arnd, OK'd by Greg KH), and actually make tegra-ahb.c
include the header to ensure client and provider agree on the prototype.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This should make it easier to delete or move <mach/*.h>; something that
is useful for single-zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Nothing from this file is used, and the file will hopefully be deleted
soon.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>

Nothing from this file is used, and the file will hopefully be deleted
soon.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Marc Dietrich <marvin24@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Nothing from this file is used, and the file will hopefully be deleted
soon.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>

Commit 13511def "regulator: deprecate regulator-compatible DT property"
now allows for simpler content within the regulators node within a PMIC.
Modify all the Tegra device tree files to take advantage of this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>

Almost nothing from this file is used, and the file will hopefully be
deleted soon. Copy the tiny portions that are used directly into
tegra_usb_phy.c. I believe that Venu Byravarasu is working on cleaning up
our USB driver, and those cleanups will remove the need for these
constants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Almost nothing from this file is used, and the file will hopefully be
deleted soon. Copy the tiny portions that are used directly into
ehci-tegra.c. I believe that Venu Byravarasu is working on cleaning up
our USB driver, and those cleanups will remove the need for these
constants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>