- 30 Jun, 2018 40 commits
-
-
Pieter Jansen van Vuuren authored
Hardware will automatically update csum in headers when a set action has been performed. This means we could in the driver ignore the explicit checksum action when performing a set action. Signed-off-by:
Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
We used to leave bus-info in ethtool driver info empty for representors in case multi-PCIe-to-single-host cards make the association between PCIe device and NFP many to one. It seems these attempts are futile, we need to link the representors to one PCIe device in sysfs to get consistent naming, plus devlink uses one PCIe as a handle, anyway. The multi-PCIe-to-single-system support won't be clean, if it ever comes. Turns out some user space (RHEL tests) likes to read bus-info so just populate it. While at it remove unnecessary app NULL-check, representors are spawned by an app, so it must exist. Signed-off-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free. Pass 0 as budget for ctrl queue completion since it runs out of a tasklet. Signed-off-by:
-
Jakub Kicinski authored
NFP NAPI handling will only complete the TXed packets when called with budget of 0, implement ndo_poll_controller by scheduling NAPI on all TX queues. Signed-off-by:
-
Jakub Kicinski authored
On some platforms with broken ACPI tables we may not have access to the Serial Number PCIe capability. This capability is crucial for us for switchdev operation as we use serial number as switch ID, and for communication with management FW where interface ID is used. If we can't determine the Serial Number we have to fail device probe. Signed-off-by:
-
Jakub Kicinski authored
After user changes the ring count statistics for deactivated rings disappear from ethtool -S output. This causes loss of information to the user and means that ethtool stats may not add up to interface stats. Always expose counters from all the rings. Note that we allocate at most num_possible_cpus() rings so number of rings should be reasonable. The alternative of only listing stats for rings which were ever in use could be confusing. Signed-off-by:
-
Vakul Garg authored
Calling skb_unclone() is expensive as it triggers a memcpy operation. Instead of calling skb_unclone() unconditionally, call it only when skb has a shared frag_list. This improves tls rx throughout significantly. Signed-off-by:
Vakul Garg <vakul.garg@nxp.com> Suggested-by:
Boris Pismenny <borisp@mellanox.com> Signed-off-by:
-
Keara Leibovitz authored
Create unittests for the tc tunnel_key action. v2: For the tests expecting failures, added non-zero exit codes in the teardowns. This prevents those tests from failing if the act_tunnel_key module is unloaded. Signed-off-by:
Keara Leibovitz <kleib@mojatatu.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Small merge conflict in net/mac80211/scan.c, I preserved the kcalloc() conversion. -DaveM Johannes Berg says: ==================== This round's updates: * finally some of the promised HE code, but it turns out to be small - but everything kept changing, so one part I did in the driver was >30 patches for what was ultimately <200 lines of code ... similar here for this code. * improved scan privacy support - can now specify scan flags for randomizing the sequence number as well as reducing the probe request element content * rfkill cleanups * a timekeeping cleanup from Arnd * various other cleanups ==================== Signed-off-by:
-
GhantaKrishnamurthy MohanKrishna authored
This commit extends the existing TIPC socket diagnostics framework for information related to TIPC group communication. Acked-by:
Ying Xue <ying.xue@windriver.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com> Signed-off-by:
-
GhantaKrishnamurthy MohanKrishna authored
A peer node is considered down if there are no active links (or) lost contact to the node. In current implementation, a peer node instance is deleted either if a) TIPC module is removed (or) b) Application can use a netlink/iproute2 interface to delete a specific down node. Thus, a down node instance lives in the system forever, unless the application explicitly removes it. We fix this by deleting the nodes which are down for a specified amount of time (5 minutes). Existing node supervision timer is used to achieve this. Acked-by:
-
Heiner Kallweit authored
The very first version of RTL8169 from 2002 (and only this one) has support for a TBI 1000BaseX fiber interface. The TBI support in the driver makes switching to phylib tricky, so best would be to get rid of it. I found no report from anybody using a device with RTL8169 and fiber interface, also the vendor driver doesn't support this mode (any longer). So remove TBI support and bail out with a message if a card with activated TBI is detected. If there really should be any user of it out there, we could add a stripped-down version of the driver supporting chip version 01 and TBI only (and maybe move it to staging). Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Tung Nguyen authored
In single-link usage, the function tipc_node_timeout() still iterates over the whole link array to handle each link. Given that the maximum number of bearers are 3, there are 2 redundant iterations with lock grab/release. Since this function is executing very frequently it makes sense to optimize it. This commit adds conditional checking to exit from the loop if the known number of configured links has already been accessed. Acked-by:
Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by:
-
Tung Nguyen authored
The function tipc_msg_extract() is using skb_clone() to clone inner messages from a message bundle buffer. Although this method is safe, it has an undesired effect that each buffer clone inherits the true-size of the bundling buffer. As a result, the buffer clone almost always ends up with being copied anyway by the message validation function. This makes the cloning into a sub-optimization. In this commit we take the consequence of this realization, and copy each inner message to a separately allocated buffer up front in the extraction function. As a bonus we can now eliminate the two cases where we had to copy re-routed packets that may potentially go out on the wire again. Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Heiner Kallweit authored
In preparation of adding phylib support to the r8169 driver we need PHY drivers for all chip-internal PHY types. Fortunately almost all of them are either supported by the Realtek PHY driver already or work with the genphy driver. Still missing is support for the PHY of RTL8169s, it requires a quirk to properly support 100Mbit-fixed mode. The quirk was copied from r8169 driver which copied it from the vendor driver. Based on the PHYID the internal PHY seems to be a RTL8211. Signed-off-by:
-
Heiner Kallweit authored
I see no need to define a private debug output symbol, let's use the standard debug output functions instead. In this context also remove the deprecated PFX define. The one assertion is wrong IMO anyway, this code path is used also by chip version 01. Signed-off-by:
-
David S. Miller authored
Ursula Braun says: ==================== smc: pnetid and SMC-D support SMC requires a configured pnet table to map Ethernet interfaces to RoCE adapter ports. For s390 there exists hardware support to group such devices. The first three patches cover the s390 pnetid support, enabling SMC-R usage on s390 without configuring an extra pnet table. SMC currently requires RoCE adapters, and uses RDMA-techniques implemented with IB-verbs. But s390 offers another method for intra-CEC Shared Memory communication. The following seven patches implement a solution to run SMC traffic based on intra-CEC DMA, called SMC-D. ==================== Signed-off-by: -
Sebastian Ott authored
Add support for the Internal Shared Memory vPCI Adapter. This driver implements the interfaces of the SMC-D protocol. Signed-off-by:
Sebastian Ott <sebott@linux.ibm.com> Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
-
Hans Wippel authored
This patch adds diag support for SMC-D. Signed-off-by:
Hans Wippel <hwippel@linux.ibm.com> Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Signed-off-by:
-
Hans Wippel authored
This patch ties together the previous SMC-D patches. It adds support for SMC-D to the listen and connect functions and, thus, enables SMC-D support in the SMC code. If a connection supports both SMC-R and SMC-D, SMC-D is preferred. Signed-off-by:
-
Hans Wippel authored
The data transfer and CDC message headers differ in SMC-R and SMC-D. This patch adds support for the SMC-D data transfer to the existing SMC code. It consists of the following: * SMC-D CDC support * SMC-D tx support * SMC-D rx support The CDC header is stored at the beginning of the receive buffer. Thus, a rx_offset variable is added for the CDC header offset within the buffer (0 for SMC-R). Signed-off-by:
-
Hans Wippel authored
There are two types of SMC: SMC-R and SMC-D. These types are signaled within the CLC messages during the CLC handshake. This patch adds support for and checks of the SMC type. Also, SMC-R and SMC-D need to exchange different information during the CLC handshake. So, this patch extends the current message formats to support the SMC-D header fields. The Proposal message can contain both SMC-R and SMC-D information. The Accept and Confirm messages contain either SMC-R or SMC-D information. Signed-off-by:
-
Hans Wippel authored
SMC-D relies on PNETIDs to find usable SMC-D/ISM devices for a SMC connection. This patch adds SMC-D/ISM support to the current PNETID implementation. Signed-off-by:
-
Hans Wippel authored
SMC supports two variants: SMC-R and SMC-D. For data transport, SMC-R uses RDMA devices, SMC-D uses so-called Internal Shared Memory (ISM) devices. An ISM device only allows shared memory communication between SMC instances on the same machine. For example, this allows virtual machines on the same host to communicate via SMC without RDMA devices. This patch adds the base infrastructure for SMC-D and ISM devices to the existing SMC code. It contains the following: * ISM driver interface: This interface allows an ISM driver to register ISM devices in SMC. In the process, the driver provides a set of device ops for each device. SMC uses these ops to execute SMC specific operations on or transfer data over the device. * Core SMC-D link group, connection, and buffer support: Link groups, SMC connections and SMC buffers (in smc_core) are extended to support SMC-D. * SMC type checks: Some type checks are added to prevent using SMC-R specific code for SMC-D and vice versa. To actually use SMC-D, additional changes to pnetid, CLC, CDC, etc. are required. These are added in follow-up patches. Signed-off-by:
-
Ursula Braun authored
The SMC protocol requires to send a separate consumer cursor update, if it cannot be piggybacked to updates of the producer cursor. Currently the decision to send a separate consumer cursor update just considers the amount of data already received by the socket program. It does not consider the amount of data already arrived, but not yet consumed by the receiver. Basing the decision on the difference between already confirmed and already arrived data (instead of difference between already confirmed and already consumed data), may lead to a somewhat earlier consumer cursor update send in fast unidirectional traffic scenarios, and thus to better throughput. Signed-off-by:
-
Ursula Braun authored
s390 hardware supports the definition of a so-call Physical NETwork IDentifier (short PNETID) per network device port. These PNETIDS can be used to identify network devices that are attached to the same physical network (broadcast domain). On s390 try to use the PNETID of the ethernet device port used for initial connecting, and derive the IB device port used for SMC RDMA traffic. On platforms without PNETID support fall back to the existing solution of a configured pnet table. Signed-off-by:
-
Ursula Braun authored
For SMC it is important to know the current port state of RoCE devices. Monitoring port states has been triggered, when a RoCE device was added to the pnet table. To support future alternatives to the pnet table the monitoring of ports is made independent of the existence of a pnet table. It starts once the smc_ib_device is established. Due to this change smc_ib_remember_port_attr() is now a local function and shuffling its location and the location of its used functions makes any forward references obsolete. And the duplicate SMC_MAX_PORTS definition is removed. Signed-off-by:
-
David S. Miller authored
Petr Machata says: ==================== Fixes for running mirror-to-gretap tests on veth The forwarding selftests infrastructure makes it possible to run the individual tests on a purely software netdevices. Names of interfaces to run the test with can be passed as command line arguments to a test. lib.sh then creates veth pairs backing the interfaces if none exist in the system. However, the tests need to recognize that they might be run on a soft device. Many mirror-to-gretap tests are buggy in this regard. This patch set aims to fix the problems in running mirror-to-gretap tests on veth devices. In patch #1, a service function is split out of setup_wait(). In patch #2, installing a trap is made optional. In patch #3, tc filters in several tests are tweaked to work with veth. In patch #4, the logic for waiting for neighbor is fixed for veth. ==================== Signed-off-by: -
Petr Machata authored
When running the test on soft devices, there's no mechanism to gratuitously start resolving the neighbor for remote tunnel endpoint. So instead of passively waiting, wait for the device to be up, and then probe the neighbor with a ping. Signed-off-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
-
Petr Machata authored
When running mirror_gre_bridge_1d_vlan tests on veth, several issues cause spurious failures: - vlan_ethtype should be ip, not ipv6 even in mirror-to-ip6gretap case, because the overlay packet is still IPv4. - Similarly ip_proto matches the innermost IP protocol, so can't be used to filter out GRE packet. Drop the corresponding condition. - Because the above fixes the filters to match in slow path as well, they need to be made skip_hw so as not to double-count packets. Signed-off-by:
-
Petr Machata authored
There are several cases where traffic that would normally be forwarded in silicon needs to be observed in slow path. That's achieved by trapping such traffic, and the functions trap_install() and trap_uninstall() realize that. However, such treatment is obviously wrong if the device in question is actually a soft device not backed by an ASIC. Therefore try to trap if possible, but fall back to inserting a continue if not. Signed-off-by:
-
Petr Machata authored
Split out of setup_wait() a function setup_wait_dev() that waits for a single device. This gives tests the opportunity to wait for a selected device after they tinkered with its upness. Signed-off-by:
-
David S. Miller authored
Radhey Shyam Pandey says: ==================== Fixes coding style in xilinx_emaclite.c This patchset fixes checkpatch and kernel-doc warnings in xilinx emaclite driver. No functional change. Changes from v2: -In 2/5 patch refactor if-else to make failure path return early. -In 2/5 patch coalesce the format onto a single line and add the missing space after the comma. ==================== Signed-off-by: -
Radhey Shyam Pandey authored
This patch fixes below checkpatch checks- CHECK: spaces preferred around that '*' (ctx:VxV) CHECK: No space is necessary after a cast Signed-off-by:
Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by:
-
Radhey Shyam Pandey authored
This patch fixes below checkpatch warnings- WARNING: Block comments use a trailing */ on a separate line WARNING: Block comments use * on subsequent lines WARNING: networking block comments don't use an empty /* line, use /* Comment Signed-off-by:
-
Radhey Shyam Pandey authored
This patch fixes below kernel-doc warnings: Function parameter or member 'maxlen' not described in 'xemaclite_recv_data' Function parameter or member 'address'not described in 'xemaclite_set_mac_address' Excess function parameter 'addr' description in 'xemaclite_set_mac_address' No description found for return value of 'xemaclite_interrupt' No description found for return value of 'xemaclite_mdio_write' Function parameter or member 'dev' not described in 'xemaclite_mdio_setup' Excess function parameter 'ofdev' description in 'xemaclite_mdio_setup' No description found for return value of 'xemaclite_open' No description found for return value of 'xemaclite_close' Excess function parameter 'match' description in 'xemaclite_of_probe' Signed-off-by:
-
Radhey Shyam Pandey authored
Remove else as it is not required with if doing a return. It also coalesce the format onto a single line and add the missing space after the comma. Fixes below checkpatch warning- WARNING: else is not generally useful after a break or return Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
-
Radhey Shyam Pandey authored
Switch hardcoded function name with a reference to __func__ making the code more maintainable. Address below checkpatch warning: WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_read', this function's name, in a string + "xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n", WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_write', this function's name, in a string + "xemaclite_mdio_write(phy_id=%i, reg=%x, val=%x)\n", Signed-off-by:
-
David S. Miller authored
Maxime Chevallier says: ==================== net: mvpp2: Add big-endian support This series allows to use PPv2 on system built as big endian. The first patch fixes the way we represent TX and RX descriptors, so that they used fixed little endianness as expected by the PPv2 controller. The second reworks the way we handle the software representation of the Header Parser entries, so that we don't use a union of arrays. The last two patches fixes some incorrect byte swapping logic, that wen't un-noticed on little-endian. This whole series doesn't fix any existing bug for little-endian systems, and since big-endian never worked for this driver, I didn't include 'fixes' tags. This was tested on MacchiatoBin (Armada 8040). ==================== Signed-off-by:
-
