Add support for VZ guest CP0_BadInstr and CP0_BadInstrP registers, as
found on most VZ capable cores. These guest registers need context
switching, and exposing via the KVM ioctl API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add support for the MIPS Virtualization (VZ) ASE to the MIPS KVM build
system. For now KVM can only be configured for T&E or VZ and not both,
but the design of the user facing APIs support the possibility of having
both available, so this could change in future.

Note that support for various optional guest features (some of which
can't be turned off) are implemented in immediately following commits,
so although it should now be possible to build VZ support, it may not
work yet on your hardware.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add the main support for the MIPS Virtualization ASE (A.K.A. VZ) to MIPS
KVM. The bulk of this work is in vz.c, with various new state and
definitions elsewhere.

Enough is implemented to be able to run on a minimal VZ core. Further
patches will fill out support for guest features which are optional or
can be disabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

The general guest exit handler needs a few tweaks for VZ compared to
trap & emulate, which for now are made directly depending on
CONFIG_KVM_MIPS_VZ:

- There is no need to re-enable the hardware page table walker (HTW), as
  it can be left enabled during guest mode operation with VZ.

- There is no need to perform a privilege check, as any guest privilege
  violations should have already been detected by the hardware and
  triggered the appropriate guest exception.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Ifdef out the trap & emulate CACHE instruction emulation functions for
VZ. We will provide separate CACHE instruction emulation in vz.c, and we
need to avoid linker errors due to the use of T&E specific MMU helpers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Update emulation of guest writes to CP0_Compare for VZ. There are two
main differences compared to trap & emulate:

 - Writing to CP0_Compare in the VZ hardware guest context acks any
   pending timer, clearing CP0_Cause.TI. If we don't want an ack to take
   place we must carefully restore the TI bit if it was previously set.

 - Even with guest timer access disabled in CP0_GuestCtl0.GT, if the
   guest CP0_Count reaches the guest CP0_Compare the timer interrupt
   will assert. To prevent this we must set CP0_GTOffset to move the
   guest CP0_Count out of the way of the new guest CP0_Compare, either
   before or after depending on whether it is a forwards or backwards
   change.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add functions for MIPS VZ TLB management to tlb.c.

kvm_vz_host_tlb_inv() will be used for invalidating root TLB entries
after GPA page tables have been modified due to a KVM page fault. It
arranges for a root GPA mapping to be flushed from the TLB, using the
gpa_mm ASID or the current GuestID to do the probe.

kvm_vz_local_flush_roottlb_all_guests() and
kvm_vz_local_flush_guesttlb_all() flush all TLB entries in the
corresponding TLB for guest mappings (GPA->RPA for root TLB with
GuestID, and all entries for guest TLB). They will be used when starting
a new GuestID cycle, when VZ hardware is enabled/disabled, and also when
switching to a guest when the guest TLB contents may be stale or belong
to a different VM.

kvm_vz_guest_tlb_lookup() converts a guest virtual address to a guest
physical address using the guest TLB. This will be used to decode guest
virtual addresses which are sometimes provided by VZ hardware in
CP0_BadVAddr for certain exceptions when the guest physical address is
unavailable.

kvm_vz_save_guesttlb() and kvm_vz_load_guesttlb() will be used to
preserve wired guest VTLB entries while a guest isn't running.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Update MIPS KVM entry code to support VZ:

 - We need to set GuestCtl0.GM while in guest mode.

 - For cores supporting GuestID, we need to set the root GuestID to
   match the main GuestID while in guest mode so that the root TLB
   refill handler writes the correct GuestID into the TLB.

 - For cores without GuestID where the root ASID dealiases RVA/GPA
   mappings, we need to load that ASID from the gpa_mm rather than the
   per-VCPU guest_kernel_mm or guest_user_mm, since the root TLB maps
   guest physical addresses. We also need to restore the normal process
   ASID on exit.

 - The normal linux process pgd needs restoring on exit, as we can't
   leave the GPA mappings active for kernel code.

 - GuestCtl0 needs saving on exit for the GExcCode field, as it may be
   clobbered if a preemption occurs.

We also need to move the TLB refill handler to the XTLB vector at offset
0x80 on 64-bit VZ kernels, as hardware will use Root.Status.KX to
determine whether a TLB refill or XTLB Refill exception is to be taken
on a root TLB miss from guest mode, and KX needs to be set for kernel
code to be able to access the 64-bit segments.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Abstract the MIPS KVM guest CP0 register access macros into inline
functions which are generated by macros. This allows them to be
generated differently for VZ, where they will usually need to access the
hardware guest CP0 context rather than the saved values in RAM.

Accessors for each individual register are generated using these macros:

 - __BUILD_KVM_*_SW() for registers which are not present in the VZ
   hardware guest context, so kvm_{read,write}_c0_guest_##name() will
   access the saved value in RAM regardless of whether VZ is enabled.

 - __BUILD_KVM_*_HW() for registers which are present in the VZ hardware
   guest context, so kvm_{read,write}_c0_guest_##name() will access the
   hardware register when VZ is enabled.

These build the underlying accessors using further macros:

 - __BUILD_KVM_*_SAVED() builds e.g. kvm_{read,write}_sw_gc0_##name()
   functions for accessing the saved versions of the registers in RAM.
   This is used for implementing the common
   kvm_{read,write}_c0_guest_##name() accessors with T&E where registers
   are always stored in RAM, but are also available with VZ HW registers
   to allow them to be accessed while saved.

 - __BUILD_KVM_*_VZ() builds e.g. kvm_{read,write}_vz_gc0_##name()
   functions for accessing the VZ hardware guest context registers
   directly. This is used for implementing the common
   kvm_{read,write}_c0_guest_##name() accessors with VZ.

 - __BUILD_KVM_*_WRAP() builds wrappers with different names, which
   allows the common kvm_{read,write}_c0_guest_##name() functions to be
   implemented using the VZ accessors while still having the SAVED
   accessors available too.

 - __BUILD_KVM_SAVE_VZ() builds functions for saving and restoring VZ
   hardware guest context register state to RAM, improving conciseness
   of VZ context saving and restoring.

Similar macros exist for generating modifiers (set, clear, change),
either with a normal unlocked read/modify/write, or using atomic LL/SC
sequences.

These changes change the types of 32-bit registers to u32 instead of
unsigned long, which requires some changes to printk() functions in MIPS
KVM.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add a callback for MIPS KVM implementations to handle the VZ guest
exit exception. Currently the trap & emulate implementation contains a
stub which reports an internal error, but the callback will be used
properly by the VZ implementation.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add an implementation callback for the kvm_arch_hardware_enable() and
kvm_arch_hardware_disable() architecture functions, with simple stubs
for trap & emulate. This is in preparation for VZ which will make use of
them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add an implementation callback for checking presence of KVM extensions.
This allows implementation specific extensions to be provided without
ifdefs in mips.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Currently the software emulated timer is initialised to a frequency of
100MHz by kvm_mips_init_count(), but this isn't suitable for VZ where
the frequency of the guest timer matches that of the host.

Add a count_hz argument so the caller can specify the default frequency,
and move the call from kvm_arch_vcpu_create() to the implementation
specific vcpu_setup() callback, so that VZ can specify a different
frequency.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add a new KVM_CAP_MIPS_64BIT capability to indicate that 64-bit MIPS
guests are available and supported. In this case it should still be
possible to run 32-bit guest code. If not available it won't be possible
to run 64-bit guest code and the instructions may not be available, or
the kernel may not support full context switching of 64-bit registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add new KVM_CAP_MIPS_VZ and KVM_CAP_MIPS_TE capabilities, and in order
to allow MIPS KVM to support VZ without confusing old users (which
expect the trap & emulate implementation), define and start checking
KVM_CREATE_VM type codes.

The codes available are:

 - KVM_VM_MIPS_TE = 0

   This is the current value expected from the user, and will create a
   VM using trap & emulate in user mode, confined to the user mode
   address space. This may in future become unavailable if the kernel is
   only configured to support VZ, in which case the EINVAL error will be
   returned and KVM_CAP_MIPS_TE won't be available even though
   KVM_CAP_MIPS_VZ is.

 - KVM_VM_MIPS_VZ = 1

   This can be provided when the KVM_CAP_MIPS_VZ capability is available
   to create a VM using VZ, with a fully virtualized guest virtual
   address space. If VZ support is unavailable in the kernel, the EINVAL
   error will be returned (although old kernels without the
   KVM_CAP_MIPS_VZ capability may well succeed and create a trap &
   emulate VM).

This is designed to allow the desired implementation (T&E vs VZ) to be
potentially chosen at runtime rather than being fixed in the kernel
configuration.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Extend MIPS KVM stats counters and kvm_transition trace event codes to
cover hypervisor exceptions, which have their own GExcCode field in
CP0_GuestCtl0 with up to 32 hypervisor exception cause codes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Update the implementation of kvm_lose_fpu() for VZ, where there is no
need to enable the FPU/MSA in the root context if the FPU/MSA state is
loaded but disabled in the guest context.

The trap & emulate implementation needs to disable FPU/MSA in the root
context when the guest disables them in order to catch the COP1 unusable
or MSA disabled exception when they're used and pass it on to the guest.

For VZ however as long as the context is loaded and enabled in the root
context, the guest can enable and disable it in the guest context
without the hypervisor having to do much, and will take guest exceptions
without hypervisor intervention if used without being enabled in the
guest context.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Implement additional MMIO emulation for MIPS64, including 64-bit
loads/stores, and 32-bit unsigned loads. These are only exposed on
64-bit VZ hosts.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Refactor MIPS KVM MMIO load/store emulation to reduce code duplication.
Each duplicate differed slightly anyway, and it will simplify adding
64-bit MMIO support for VZ.

kvm_mips_emulate_store() and kvm_mips_emulate_load() can now return
EMULATE_DO_MMIO (as possibly originally intended). We therefore stop
calling either of these from kvm_mips_emulate_inst(), which is now only
used by kvm_trap_emul_handle_cop_unusable() which is picky about return
values.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Emulate the HYPCALL instruction added in the VZ ASE and used by the MIPS
paravirtualised guest support that is already merged. The new hypcall.c
handles arguments and the return value. No actual hypercalls are yet
supported, but this still allows us to safely step over hypercalls and
set an error code in the return value for forward compatibility.

Non-zero HYPCALL codes are not handled.

We also document the hypercall ABI which asm/kvm_para.h uses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add a distinct UNIQUE_GUEST_ENTRYHI() macro for invalidation of guest
TLB entries by KVM, using addresses in KSeg1 rather than KSeg0. This
avoids conflicts with guest invalidation routines when there is no EHINV
bit to mark the whole entry as invalid, avoiding guest machine check
exceptions on Cavium Octeon III.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add some missing guest accessors and register field definitions for KVM
for MIPS VZ to make use of.

Guest CP0_LLAddr register accessors and definitions for the LLB field
allow KVM to clear the guest LLB to cancel in-progress LL/SC atomics on
restore, and to emulate accesses by the guest to the CP0_LLAddr
register.

Bitwise modifiers and definitions for the guest CP0_Wired and
CP0_Config1 registers allow KVM to modify fields within the CP0_Wired
and CP0_Config1 registers.

Finally a definition for the CP0_Config5.SBRI bit allows KVM to
initialise and allow modification of the guest version of the SBRI bit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Probe for availablility of M{T,F}HC0 instructions used with e.g. XPA in
the VZ guest context, and make it available via cpu_guest_has_mvh. This
will be helpful in properly emulating the MAAR registers in KVM for MIPS
VZ.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Probe for presence of guest CP0_UserLocal register and expose via
cpu_guest_has_userlocal. This register is optional pre-r6, so this will
allow KVM to only save/restore/expose the guest CP0_UserLocal register
if it exists.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

The MAAR V bit has been renamed VL since another bit called VH is added
at the top of the register when it is extended to 64-bits on a 32-bit
processor with XPA. Rename the V definition, fix the various users, and
add definitions for the VH bit. Also add a definition for the MAARI
Index field.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Add definitions and probing of the UFR bit in Config5. This bit allows
user mode control of the FR bit (floating point register mode). It is
present if the UFRP bit is set in the floating point implementation
register.

This is a capability KVM may want to expose to guest kernels, even
though Linux is unlikely to ever use it due to the implications for
multi-threaded programs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check.  The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.

I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there.  I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.

Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more powerpc fixes from Michael Ellerman:
 "A couple of minor powerpc fixes for 4.11:

   - wire up statx() syscall

   - don't print a warning on memory hotplug when HPT resizing isn't
     available

  Thanks to: David Gibson, Chandan Rajendra"

* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Don't give a warning when HPT resizing isn't available
  powerpc: Wire up statx() syscall

Pull parisc fixes from Helge Deller:

 - Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
   modules with CONFIG_MODVERSIONS.

 - Dave Anglin optimized the cache flushing for vmap ranges.

 - Arvind Yadav provided a fix for a potential NULL pointer dereference
   in the parisc perf code (and some code cleanups).

 - I wired up the new statx system call, fixed some compiler warnings
   with the access_ok() macro and fixed shutdown code to really halt a
   system at shutdown instead of crashing & rebooting.

* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix system shutdown halt
  parisc: perf: Fix potential NULL pointer dereference
  parisc: Avoid compiler warnings with access_ok()
  parisc: Wire up statx system call
  parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
  parisc: support R_PARISC_SECREL32 relocation in modules

Pull SCSI target fixes from Nicholas Bellinger:
 "The bulk of the changes are in qla2xxx target driver code to address
  various issues found during Cavium/QLogic's internal testing (stable
  CC's included), along with a few other stability and smaller
  miscellaneous improvements.

  There are also a couple of different patch sets from Mike Christie,
  which have been a result of his work to use target-core ALUA logic
  together with tcm-user backend driver.

  Finally, a patch to address some long standing issues with
  pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
  which will make folks using physical (or virtual) magnetic tape happy"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
  qla2xxx: Update driver version to 9.00.00.00-k
  qla2xxx: Fix delayed response to command for loop mode/direct connect.
  qla2xxx: Change scsi host lookup method.
  qla2xxx: Add DebugFS node to display Port Database
  qla2xxx: Use IOCB interface to submit non-critical MBX.
  qla2xxx: Add async new target notification
  qla2xxx: Export DIF stats via debugfs
  qla2xxx: Improve T10-DIF/PI handling in driver.
  qla2xxx: Allow relogin to proceed if remote login did not finish
  qla2xxx: Fix sess_lock & hardware_lock lock order problem.
  qla2xxx: Fix inadequate lock protection for ABTS.
  qla2xxx: Fix request queue corruption.
  qla2xxx: Fix memory leak for abts processing
  qla2xxx: Allow vref count to timeout on vport delete.
  tcmu: Convert cmd_time_out into backend device attribute
  tcmu: make cmd timeout configurable
  tcmu: add helper to check if dev was configured
  target: fix race during implicit transition work flushes
  target: allow userspace to set state to transitioning
  target: fix ALUA transition timeout handling
  ...

Pull device-dax fixes from Dan Williams:
 "The device-dax driver was not being careful to handle falling back to
  smaller fault-granularity sizes.

  The driver already fails fault attempts that are smaller than the
  device's alignment, but it also needs to handle the cases where a
  larger page mapping could be established. For simplicity of the
  immediate fix the implementation just signals VM_FAULT_FALLBACK until
  fault-size == device-alignment.

  One fix is for -stable to address pmd-to-pte fallback from the
  original implementation, another fix is for the new (introduced in
  4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
  ride.

  These have received a build success notification from the kbuild
  robot"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fix debug output typo
  device-dax: fix pud fault fallback handling
  device-dax: fix pmd/pte fault fallback handling

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.

Following commands are being routed through IOCB interface

- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Add routines to support T10 DIF tag.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>