- 05 Jan, 2021 18 commits
-
-
Chen Li authored
When using e8860(gcn1) on arm64, the kernel crashed on drm/radeon: [ 11.240414] pc : __memset+0x4c/0x188 [ 11.244101] lr : radeon_uvd_get_create_msg+0x114/0x1d0 [radeon] [ 11.249995] sp : ffff00000d7eb700 [ 11.253295] x29: ffff00000d7eb700 x28: ffff8001f632a868 [ 11.258585] x27: 0000000000040000 x26: ffff00000de00000 [ 11.263875] x25: 0000000000000125 x24: 0000000000000001 [ 11.269168] x23: 0000000000000000 x22: 0000000000000005 [ 11.274459] x21: ffff00000df24000 x20: ffff8001f74b4000 [ 11.279753] x19: 0000000000124000 x18: 0000000000000020 [ 11.285043] x17: 0000000000000000 x16: 0000000000000000 [ 11.290336] x15: ffff000009309000 x14: ffffffffffffffff [ 11.290340] x13: ffff0000094b6f88 x12: ffff0000094b6bd2 [ 11.290343] x11: ffff00000d7eb700 x10: ffff00000d7eb700 [ 11.306246] x9 : ffff00000d7eb700 x8 : ffff00000df2402c [ 11.306254] x7 : 0000000000000000 x6 : ffff0000094b626a [ 11.306257] x5 : 0000000000000000 x4 : 0000000000000004 [ 11.306262] x3 : ffffffffffffffff x2 : 0000000000000fd4 [ 11.306265] x1 : 0000000000000000 x0 : ffff00000df2402c [ 11.306272] Call trace: [ 11.306316] __memset+0x4c/0x188 [ 11.306638] uvd_v1_0_ib_test+0x70/0x1c0 [radeon] [ 11.306758] radeon_ib_ring_tests+0x54/0xe0 [radeon] ... Obviously, the __memset call is generated by gcc(8.3.1). It optimizes this for loop into memset. But this may break on some platforms which cannot map device memory correctly. So, just invoke `writel` to handle this. v3 (chk): minor cleanups in code and commit message Signed-off-by:
Chen Li <chenli@uniontech.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Dennis Li authored
When GFXOFF is enabled and GPU is idle, driver will fail to access some registers. Therefore change to disable power gating before all access registers with MMIO. Dmesg log is as following: amdgpu 0000:03:00.0: amdgpu: amdgpu: finishing device. amdgpu: cp queue pipe 4 queue 0 preemption failed amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2 amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706 amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2 amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706 Signed-off-by:
Dennis Li <Dennis.Li@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
-
Dennis Li authored
ASD and TA share the same firmware in SIENNA_CICHLID and only TA firmware is requested during boot, so only need release TA firmware when remove device. [ 83.877150] general protection fault, probably for non-canonical address 0x1269f97e6ed04095: 0000 [#1] SMP PTI [ 83.888076] CPU: 0 PID: 1312 Comm: modprobe Tainted: G W OE 5.9.0-rc5-deli-amd-vangogh-0.0.6.6-114-gdd99d5669a96-dirty #2 [ 83.901160] Hardware name: System manufacturer System Product Name/TUF Z370-PLUS GAMING II, BIOS 0411 09/21/2018 [ 83.912353] RIP: 0010:free_fw_priv+0xc/0x120 [ 83.917531] Code: e8 99 cd b0 ff b8 a1 ff ff ff eb 9f 4c 89 f7 e8 8a cd b0 ff b8 f4 ff ff ff eb 90 0f 1f 00 0f 1f 44 00 00 55 48 89 e5 41 54 53 <4c> 8b 67 18 48 89 fb 4c 89 e7 e8 45 94 41 00 b8 ff ff ff ff f0 0f [ 83.937576] RSP: 0018:ffffbc34c13a3ce0 EFLAGS: 00010206 [ 83.943699] RAX: ffffffffbb681850 RBX: ffffa047f117eb60 RCX: 0000000080800055 [ 83.951879] RDX: ffffbc34c1d5f000 RSI: 0000000080800055 RDI: 1269f97e6ed04095 [ 83.959955] RBP: ffffbc34c13a3cf0 R08: 0000000000000000 R09: 0000000000000001 [ 83.968107] R10: ffffbc34c13a3cc8 R11: 00000000ffffff00 R12: ffffa047d6b23378 [ 83.976166] R13: ffffa047d6b23338 R14: ffffa047d6b240c8 R15: 0000000000000000 [ 83.984295] FS: 00007f74f6712540(0000) GS:ffffa047fbe00000(0000) knlGS:0000000000000000 [ 83.993323] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 84.000056] CR2: 0000556a1cca4e18 CR3: 000000021faa8004 CR4: 00000000003706f0 [ 84.008128] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 84.016155] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 84.024174] Call Trace: [ 84.027514] release_firmware.part.11+0x4b/0x70 [ 84.033017] release_firmware+0x13/0x20 [ 84.037803] psp_sw_fini+0x77/0xb0 [amdgpu] [ 84.042857] amdgpu_device_fini+0x38c/0x5d0 [amdgpu] [ 84.048815] amdgpu_driver_unload_kms+0x43/0x70 [amdgpu] [ 84.055055] drm_dev_unregister+0x73/0xb0 [drm] [ 84.060499] drm_dev_unplug+0x28/0x30 [drm] [ 84.065598] amdgpu_dev_uninit+0x1b/0x40 [amdgpu] [ 84.071223] amdgpu_pci_remove+0x4e/0x70 [amdgpu] [ 84.076835] pci_device_remove+0x3e/0xc0 [ 84.081609] device_release_driver_internal+0xfb/0x1c0 [ 84.087558] driver_detach+0x4d/0xa0 [ 84.092041] bus_remove_driver+0x5f/0xe0 [ 84.096854] driver_unregister+0x2f/0x50 [ 84.101594] pci_unregister_driver+0x22/0xa0 [ 84.106806] amdgpu_exit+0x15/0x2b [amdgpu] Signed-off-by:
-
Hawking Zhang authored
global noretry setting is cached to gmc.noretry Signed-off-by:
-
Jiansong Chen authored
For sdma5.2, all sdma instances will share the same fw, remove unnecessary asic check to be more generic. Signed-off-by:
Jiansong Chen <Jiansong.Chen@amd.com> Reviewed-by:
-
Kevin Wang authored
fix NULL pointer issue when read sysfs amdgpu_current_backlight_pwm sysfs node. Call Trace: [ 248.273833] BUG: kernel NULL pointer dereference, address: 0000000000000130 [ 248.273930] #PF: supervisor read access in kernel mode [ 248.273993] #PF: error_code(0x0000) - not-present page [ 248.274054] PGD 0 P4D 0 [ 248.274092] Oops: 0000 [#1] SMP PTI [ 248.274138] CPU: 2 PID: 1377 Comm: cat Tainted: G OE 5.9.0-rc5-drm-next-5.9+ #1 [ 248.274233] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 3802 03/15/2018 [ 248.274641] RIP: 0010:dc_link_get_backlight_level+0x5/0x70 [amdgpu] [ 248.274718] Code: 67 ff ff ff 41 b9 03 00 00 00 e9 45 ff ff ff d1 ea e9 55 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <48> 8b 87 30 01 00 00 48 8b 00 48 8b 88 88 03 00 00 48 8d 81 e8 01 [ 248.274919] RSP: 0018:ffffb5ad809b3df0 EFLAGS: 00010203 [ 248.274982] RAX: ffffa0f77d1c0010 RBX: ffffa0f793ae9168 RCX: 0000000000000001 [ 248.275064] RDX: ffffa0f79753db00 RSI: 0000000000000001 RDI: 0000000000000000 [ 248.275145] RBP: ffffb5ad809b3e00 R08: ffffb5ad809b3da0 R09: 0000000000000000 [ 248.275225] R10: ffffb5ad809b3e68 R11: 0000000000000000 R12: ffffa0f793ae9190 [ 248.275306] R13: ffffb5ad809b3ef0 R14: 0000000000000001 R15: ffffa0f793ae9168 [ 248.275388] FS: 00007f5f1ec4d540(0000) GS:ffffa0f79ec80000(0000) knlGS:0000000000000000 [ 248.275480] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 248.275547] CR2: 0000000000000130 CR3: 000000042a03c005 CR4: 00000000003706e0 [ 248.275628] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 248.275708] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 248.275789] Call Trace: [ 248.276124] ? current_backlight_read+0x24/0x40 [amdgpu] [ 248.276194] seq_read+0xc3/0x3f0 [ 248.276240] full_proxy_read+0x5c/0x90 [ 248.276290] vfs_read+0xa7/0x190 [ 248.276334] ksys_read+0xa7/0xe0 [ 248.276379] __x64_sys_read+0x1a/0x20 [ 248.276429] do_syscall_64+0x37/0x80 [ 248.276477] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 248.276538] RIP: 0033:0x7f5f1e75c191 [ 248.276585] Code: fe ff ff 48 8d 3d b7 9d 0a 00 48 83 ec 08 e8 46 4d 02 00 66 0f 1f 44 00 00 48 8d 05 71 07 2e 00 8b 00 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 41 54 55 49 89 d4 53Hw [ 248.276784] RSP: 002b:00007ffcb1fc3f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [ 248.276872] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f5f1e75c191 [ 248.276953] RDX: 0000000000020000 RSI: 00007f5f1ec2b000 RDI: 0000000000000003 [ 248.277034] RBP: 0000000000020000 R08: 00000000ffffffff R09: 0000000000000000 [ 248.277115] R10: 0000000000000022 R11: 0000000000000246 R12: 00007f5f1ec2b000 [ 248.277195] R13: 0000000000000003 R14: 00007f5f1ec2b00f R15: 0000000000020000 [ 248.277279] Modules linked in: amdgpu(OE) iommu_v2 gpu_sched ttm(OE) drm_kms_helper cec drm i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt rpcsec_gss_krb5 auth_rpcgss nfsv4 nfs lockd grace fscache nls_iso8859_1 snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic ledtrig_audio intel_rapl_msr intel_rapl_common snd_hda_intel snd_intel_dspcfg x86_pkg_temp_thermal intel_powerclamp snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_seq_midi snd_seq_midi_event mei_hdcp coretemp snd_rawmidi snd_seq kvm_intel kvm snd_seq_device snd_timer irqbypass joydev snd input_leds soundcore crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper rapl intel_cstate mac_hid mei_me serio_raw mei eeepc_wmi wmi_bmof asus_wmi mxm_wmi intel_wmi_thunderbolt acpi_pad sparse_keymap efi_pstore sch_fq_codel parport_pc ppdev lp parport sunrpc ip_tables x_tables autofs4 hid_logitech_hidpp hid_logitech_dj hid_generic usbhid hid e1000e psmouse ahci libahci wmi video [ 248.278211] CR2: 0000000000000130 [ 248.278221] ---[ end trace 1fbe72fe6f91091d ]--- [ 248.357226] RIP: 0010:dc_link_get_backlight_level+0x5/0x70 [amdgpu] [ 248.357272] Code: 67 ff ff ff 41 b9 03 00 00 00 e9 45 ff ff ff d1 ea e9 55 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <48> 8b 87 30 01 00 00 48 8b 00 48 8b 88 88 03 00 00 48 8d 81 e8 01 Signed-off-by:
Kevin Wang <kevin1.wang@amd.com> Acked-by:
-
Xiaojian Du authored
This patch is to add support to umd P-state function for vangogh. It enables the "set" function of 3 sysfs nodes: pp_dpm_mclk, pp_dpm_fclk, pp_dpm_socclk, the functions is used to set the DPM frequency level of memclk/fclk/socclk. Due to only after enabling the "power_dpm_force_performance_level" sysfs node, it is allowed to set these three nodes, so this patch also enables the "powe_dpm_force_performance_level" sysfs node, which is used to change power profile. Signed-off-by:
Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
-
Xiaojian Du authored
This patch is to add some basic functions to support umd P-state function for vangogh. Signed-off-by:
-
Xiaojian Du authored
This patch is to add some basic functions to support umd P-state function for vangogh. Signed-off-by:
-
Xiaojian Du authored
This patch is to enable the fine grain tuning function for renoir. Signed-off-by:
-
Xiaojian Du authored
This patch is to add the fine grain tuning function for renoir. This function uses the pp_od_clk_voltage sysfs file to configure the min and max value of gfx clock frequency manually or restore the default value. Command guide: echo "s level value" > pp_od_clk_voltage "s" - set the sclk frequency "level" - 0 or 1, "0" represents the min value, "1" represents the max value "value" - the target value of sclk frequency, it should be limited in the safe range echo "r" > pp_od_clk_voltage "r" - reset the sclk frequency, restore the default value instantly echo "c" > pp_od_clk_voltage "c" - commit the min and max value of sclk frequency to the system only after the commit command, the target values set by "s" command will take effect. Example: 1)change power profile from "auto" to "standard" $ cat power_dpm_force_performance_level auto $ echo "profile_standard" > power_dpm_force_performance_level $ cat power_dpm_force_performance_level profile_standard 2)check the default sclk frequency $ cat pp_od_clk_voltage OD_SCLK: 0: 200Mhz 1: 1400Mhz OD_RANGE: SCLK: 200MHz 1400MHz 3)use "s" -- set command to configure the min and max sclk frequency $ echo "s 0 600" > pp_od_clk_voltage $ echo "s 1 1000" > pp_od_clk_voltage $ echo "c" > pp_od_clk_voltage $ cat pp_od_clk_voltage OD_SCLK: 0: 600Mhz 1: 1000Mhz OD_RANGE: SCLK: 200MHz 1400MHz 4)use "r" -- reset command to restore the min or max sclk frequency $ echo "r" > pp_od_clk_voltage $ cat pp_od_clk_voltage OD_SCLK: 0: 200Mhz 1: 1400Mhz OD_RANGE: SCLK: 200MHz 1400MHz Signed-off-by: -
John Clements authored
sienna cichlid interfaces with RAS eeprom on I2C controller port 1 Reviewed-by:
John Clements <john.clements@amd.com> Signed-off-by:
-
Xiaojian Du authored
This patch is to improve the fine grain tuning function for RV/RV2/PCO. This patch adds two new commands: "restore" and "commit". This function uses the pp_od_clk_voltage sysfs file to configure the min and max value of gfx clock frequency manually or restore the default value. Command guide: echo "s level value" > pp_od_clk_voltage "s" - set the sclk frequency "level" - 0 or 1, "0" represents the min value, "1" represents the max value "value" - the target value of sclk frequency, it should be limited in the safe range echo "r" > pp_od_clk_voltage "r" - reset the sclk frequency, restore the default value instantly echo "c" > pp_od_clk_voltage "c" - commit the min and max value of sclk frequency to the system only after the commit command, the target values set by "s" command will take effect. Example: 1)change power profile from "auto" to "manual" $ cat power_dpm_force_performance_level auto $ echo "manual" > power_dpm_force_performance_level $ cat power_dpm_force_performance_level manual 2)check the default sclk frequency $ cat pp_od_clk_voltage OD_SCLK: 0: 200Mhz 1: 1400Mhz OD_RANGE: SCLK: 200MHz 1400MHz 3)use "s" -- set command to configure the min and max sclk frequency $ echo "s 0 600" > pp_od_clk_voltage $ echo "s 1 1000" > pp_od_clk_voltage $ echo "c" > pp_od_clk_voltage $ cat pp_od_clk_voltage OD_SCLK: 0: 600Mhz 1: 1000Mhz OD_RANGE: SCLK: 200MHz 1400MHz 4)use "r" -- reset command to restore the min or max sclk frequency $ echo "r" > pp_od_clk_voltage $ cat pp_od_clk_voltage OD_SCLK: 0: 200Mhz 1: 1400Mhz OD_RANGE: SCLK: 200MHz 1400MHz Signed-off-by:Evan Quan <evan.quan@amd.com> Signed-off-by:
-
Xiaojian Du authored
This patch is to enable the "fetch" function of pp_dpm_vclk and pp_dpm_dclk. It allows to fetch the current frequency of vcn and dcn and their DPM levels for vangogh. Signed-off-by:
-
Xiaojian Du authored
This patch is to add two new sysfs nodes for vangogh: pp_dpm_dclk and pp_dpm_vclk. The two sysfs nodes are similar to pp_dpm_fclk/memclk/socclk. pp_dpm_dclk represents the DPM frequency of dcn unit. pp_dpm_vclk represents the DPM frequency of vcn unit. Signed-off-by:
-
Xiaojian Du authored
This patch is to add new feature map macros to resolve duplicate name. Vangogh uses one different format to name some feature bits of swSMU, it causes some duplicate name in the existing feature map list. Signed-off-by:
-
Xiaojian Du authored
This patch is to add supoort to umd P-state function for vangogh. It enables the "fetch" function of 3 sysfs nodes: pp_dpm_mclk, pp_dpm_fclk, pp_dpm_socclk,the function is used to fetch the current frequency of memclk/fclk/socclk. Signed-off-by:
-
Xiaojian Du authored
This patch is to correct the sensor value of power for vangogh. Signed-off-by:
-
- 23 Dec, 2020 22 commits
-
-
Hawking Zhang authored
the psp access ih path is not needed in navi Signed-off-by:
Jane Jian <Jane.Jian@amd.com> Signed-off-by:
-
Markus Elfring authored
Adjust a jump target so that a bit of exception handling can be better reused at the end of this function. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Markus Elfring authored
* Return directly after a call of the function “kzalloc” failed at the beginning. * Delete a label which became unnecessary with this refactoring. Signed-off-by:
-
Alex Deucher authored
We can have the same src ids for different client ids so make sure to check both the client id and the source id when handling interrupts. Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
-
Alex Deucher authored
We need to take into account the client id otherwise we'll end up sending generic events for any src id that is registered. We only support irq domains on pre-soc15 parts so client is always legacy. Reviewed-by:
-
Hawking Zhang authored
tear down software ih ring and its state. Signed-off-by:
Feifei Xu <Feifei.Xu@amd.com> Signed-off-by:
-
Hawking Zhang authored
software ih ring is enabled in vega10 and navi ih block by default. Signed-off-by:
-
Hawking Zhang authored
software ih ring will be used as a workaround in case hardware ih ring 1 and ring 2 don't work Signed-off-by:
-
Evan Quan authored
This is supported by Sienna Cichlid, Navy Flounder and Dimgrey Cavefish. For these ASICs, the target voltage calculation can be illustrated by "voltage = voltage calculated from v/f curve + overdrive vddgfx offset". V2: limit the smu_version check for Sienna Cichlid only Here are some sample usages about this new OD setting: 1. Check current vddgfx offset setting by cat /sys/class/drm/card0/device/pp_od_clk_voltage ... ... OD_VDDGFX_OFFSET: 0mV ... ... 2. Set new vddgfx offset by echo "vo 10" > /sys/class/drm/card0/device/pp_od_clk_voltage cat /sys/class/drm/card0/device/pp_od_clk_voltage ... ... OD_VDDGFX_OFFSET: 10mV ... ... 3. Commit the new setting by echo "c" > /sys/class/drm/card0/device/pp_od_clk_voltage Signed-off-by:
-
Evan Quan authored
Enable Sienna Cichlid gfxclk/uclk overdrive support. Signed-off-by:
-
Evan Quan authored
Populate the bootup overdrive table settings. Signed-off-by:
-
Jinzhou Su authored
When user specifies a reduced WGP(CU) config via disalbe_cu module parameter, this does not disable the clocks which uses additional power. This interface send active WGP number to SMU and SMU will cooperate with RLC to power off relative WGPs. v2: Add request active WGPs in Vangogh smu post init. Signed-off-by:
Jinzhou.Su <Jinzhou.Su@amd.com> Reviewed-by:
Lijo Lazar <lijo.lazar@amd.com> Signed-off-by:
-
Ryan Taylor authored
Documents the hooks in struct pptable_funcs. v2: Improved documentation accuracy. v3: Improved set_default_od_settings() definition. Signed-off-by:
Ryan Taylor <Ryan.Taylor@amd.com> Reviewed-by:
-
Hawking Zhang authored
APUs don't support ih ring 1 and ring 2. Signed-off-by:
-
Hawking Zhang authored
For all the ASICs that integrate psp v11, vega20 doesn't support ih reroute. arcturus and later will allow kernel driver to program ih_cfg_index/data through mmio directly. navi1x and onwards will only support grb_ih_set command in sriov configuration. psp_v11_0_reroute_ih is not needed any more. Signed-off-by:
-
Hawking Zhang authored
except for RENOIR, it is not correct to have IH_CHICKEN programming in vega10 ih block. Signed-off-by:
-
Hawking Zhang authored
IH_CHICKEN.MC_SPACE_FBPA_ENABLE field is only valid when IH_RB_CNTL.MC_SPACE is programed to 0x3, frame buffer physical address. For both bus address and gpu virtual address, don't program MC_SPACE_FBPA_ENABLE field Signed-off-by:
-
Hawking Zhang authored
already switched to vega20 ih block for vega20 and arcturus. no need to add vega20 support in navi10 ih block Signed-off-by:
-
Hawking Zhang authored
replace navi10 ih block with vega20 ih block for vega20 and arcturus Signed-off-by:
-
Hawking Zhang authored
in case page faults overwhlem the interrupt handlers and the driver lost the valuable interrupt information Signed-off-by:
-
Hawking Zhang authored
vega20 ih blocks will be used for vega20/arcturus Signed-off-by:
-
Hawking Zhang authored
v1: add osssys v4_2 register offset and shift masks header files. vega20 and arcturus will refer to these ip headers. (Hawking) v2: clean up osssys v4_2 registers (Alex) Signed-off-by:
-
