- 31 Mar, 2022 38 commits
-
-
Marek Vasut authored
Implement .atomic_get_input_bus_fmts callback, which sets up the input (scanout-engine-end) formats, so that those formats can then be used in pipeline format negotiation between this bridge and the scanout engine. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Dave Airlie <airlied@redhat.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by:
Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220331153923.14314-2-marex@denx.de
-
Marek Vasut authored
Use the atomic version of the enable/disable operations to continue the transition to the atomic API. This will be needed to access the mode from the atomic state. Signed-off-by:
-
Marek Vasut authored
In rare cases, the bridge may not start up correctly, which usually leads to no display output. In case this happens, warn about it in the kernel log. Signed-off-by:
-
Marek Vasut authored
Read out the Vendor/Chip/Version ID registers from the chip before performing any configuration, and validate that the registers have correct values. This is mostly a simple test whether DSI register access does work, since that tends to be broken on various bridges. Acked-by:
Maxime Ripard <maxime@cerno.tech> Signed-off-by:
-
Marek Vasut authored
Rename and inline macro ICN6211_DSI() into function chipone_writeb() to keep all function names lower-case. No functional change. Acked-by:
-
Marek Vasut authored
The ICN6211 chip starts in I2C configuration mode after cold boot. Implement support for configuring the chip via I2C in addition to the current DSI LP command mode configuration support. The later seems to be available only on chips which have additional MCU on the panel/bridge board which preconfigures the ICN6211, while the I2C configuration mode added by this patch does not require any such MCU. Acked-by:
-
Marek Vasut authored
Implement .atomic_get_input_bus_fmts callback, which sets up the input (DSI-end) format, and that format can then be used in pipeline format negotiation between the DSI-end of this bridge and the other component closer to the scanout engine. Acked-by:
-
Marek Vasut authored
Both example code [1], [2] as well as one provided by custom panel vendor set register SYS_CTRL_1 to 0x88. What exactly does the value mean is unknown due to unavailable datasheet. Align this register value with example code. [1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c [2] https://github.com/tdjastrzebski/ICN6211-ConfiguratorAcked-by:
-
Marek Vasut authored
The chip is capable of swapping DPI RGB channels. The driver currently does not implement support for this functionality. Write the MIPI_PN_SWAP register to 0 to assure the color swap is disabled. Acked-by:
-
Marek Vasut authored
The DSI burst mode is more energy efficient than the DSI sync pulse mode, make use of the burst mode since the chip supports it as well. Disable the generation of EoT packet, the chip ignores it, so no point in emitting it. Enable transmission of data in LP mode, otherwise register read via DSI does not work with this chip. Acked-by:
-
Marek Vasut authored
The chip contains fractional PLL, however the driver currently hard-codes one specific PLL setting. Implement generic PLL parameter calculation code, so any DPI panel with arbitrary pixel clock can be attached to this bridge. The datasheet for this bridge is not available, the PLL behavior has been inferred from [1] and [2] and by analyzing the DPI pixel clock with scope. The PLL limits might be wrong, but at least the calculated values match all the example code available. This is better than one hard-coded pixel clock value anyway. [1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c [2] https://github.com/tdjastrzebski/ICN6211-ConfiguratorAcked-by:
-
Marek Vasut authored
The driver currently hard-codes HS/VS polarity to active-low and DE to active-high, which is not correct for a lot of supported DPI panels. Add the missing mode flag handling for HS/VS/DE polarity. Acked-by:
-
Marek Vasut authored
The HFP_HSW_HBP_HI register must be programmed with 2 LSbits of each Horizontal Front Porch/Sync/Back Porch. Currently the driver programs this register to 0, which breaks displays with either value above 255. The HFP_MIN register must be set to the same value as HFP_LI, otherwise there is visible image distortion, usually in the form of missing lines at the bottom of the panel. Fix this by correctly programming the HFP_HSW_HBP_HI and HFP_MIN registers. Acked-by:
-
Marek Vasut authored
The chip register layout has nothing to do with MIPI DCS, the registers incorrectly marked as MIPI DCS in the driver are regular chip registers often with completely different function. Fill in the actual register names and bits from [1] and [2] and add the entire register layout, since the documentation for this chip is hard to come by. [1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c [2] https://github.com/tdjastrzebski/ICN6211-ConfiguratorAcked-by:
-
Jagan Teki authored
The new support drm bridges are moving towards atomic functions. Replace atomic version of functions to continue the transition to the atomic API. Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Acked-by:
Marek Szyprowski <m.szyprowski@samsung.com> Tested-by:
-
Jagan Teki authored
Convert the encoders to bridge drivers in order to standardize on a single API with built-in dumb encoder support for compatibility with existing component drivers. Driver bridge conversion will help to reuse the same bridge on different platforms as exynos dsi driver can be used as a Samsung DSIM and use it for i.MX8MM platform. Bridge conversion, - Drops drm_encoder_helper_funcs. - Adds drm_bridge_funcs and register a drm bridge. - Drops bridge_chain. - Separate pre_enable from enable function. - Separate post_disable from disable function. Convert it. Signed-off-by:
-
Jagan Teki authored
Replace the manual panel handling code by a drm panel_bridge via devm_drm_of_get_bridge(). Adding panel_bridge handling, - Drops drm_connector and related operations as drm_bridge_attach creates connector during attachment. - Drops panel pointer and iterate the bridge, so-that it can operate the normal bridge and panel_bridge in constitutive callbacks. This simplifies the driver and allows all components in the display pipeline to be treated as bridges. Signed-off-by:
-
Jagan Teki authored
MIC drivers in the Exynos5433 display pipeline are already registered as bridge drivers and it is more advisable to attach the downstream bridge on the bridge attach call instead of doing the same in the DSI driver. This makes bridge attachment more meaningful and avoids the races during bridge function calls. So, move the bridge finding and drm_bridge_attach from DSI to MIC. Signed-off-by:
-
Jagan Teki authored
Trigger hotplug event with drm_kms_helper_hotplug_event might fail if the connector state pointer is NULL. BUG observed in exynos dsi driver where drm_bridge_attach is trying to register a connector in panel_bridge before the hotplug event is triggered. WARNING: CPU: 1 PID: 1 at drivers/gpu/drm/drm_atomic_state_helper.c:494 drm_atomic_helper_connector_duplicate_state+0x94/0x9c Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 5.16.0-rc1-00009-g704b1dbfa4c2 #11058 Hardware name: Samsung Exynos (Flattened Device Tree) [<c0110b30>] (unwind_backtrace) from [<c010c618>] (show_stack+0x10/0x14) [<c010c618>] (show_stack) from [<c0b657d4>] (dump_stack_lvl+0x58/0x70) [<c0b657d4>] (dump_stack_lvl) from [<c01261dc>] (__warn+0xd0/0x134) [<c01261dc>] (__warn) from [<c0b5f628>] (warn_slowpath_fmt+0x5c/0xb4) [<c0b5f628>] (warn_slowpath_fmt) from [<c064bce4>] (drm_atomic_helper_connector_duplicate_state+0x94/0x9c) [<c064bce4>] (drm_atomic_helper_connector_duplicate_state) from [<c0666b64>] (drm_atomic_get_connector_state+0xd4/0x190) [<c0666b64>] (drm_atomic_get_connector_state) from [<c0667928>] (__drm_atomic_helper_set_config+0x314/0x368) [<c0667928>] (__drm_atomic_helper_set_config) from [<c067e628>] (drm_client_modeset_commit_atomic+0x170/0x278) [<c067e628>] (drm_client_modeset_commit_atomic) from [<c067e800>] (drm_client_modeset_commit_locked+0x60/0x1c8) [<c067e800>] (drm_client_modeset_commit_locked) from [<c067e98c>] (drm_client_modeset_commit+0x24/0x40) [<c067e98c>] (drm_client_modeset_commit) from [<c06509c0>] (drm_fb_helper_set_par+0xb8/0xf8) [<c06509c0>] (drm_fb_helper_set_par) from [<c05b86d0>] (fbcon_init+0x2c0/0x518) [<c05b86d0>] (fbcon_init) from [<c060636c>] (visual_init+0xc0/0x108) [<c060636c>] (visual_init) from [<c06085e4>] (do_bind_con_driver+0x1b8/0x3a4) [<c06085e4>] (do_bind_con_driver) from [<c0608b40>] (do_take_over_console+0x13c/0x1e8) [<c0608b40>] (do_take_over_console) from [<c05b6854>] (do_fbcon_takeover+0x78/0xd8) [<c05b6854>] (do_fbcon_takeover) from [<c05b1154>] (register_framebuffer+0x208/0x2e0) [<c05b1154>] (register_framebuffer) from [<c064ead0>] (__drm_fb_helper_initial_config_and_unlock+0x400/0x63c) [<c064ead0>] (__drm_fb_helper_initial_config_and_unlock) from [<c063a718>] (drm_kms_helper_hotplug_event+0x24/0x30) [<c063a718>] (drm_kms_helper_hotplug_event) from [<c068f668>] (exynos_dsi_host_attach+0x174/0x1fc) [<c068f668>] (exynos_dsi_host_attach) from [<c0699354>] (s6e8aa0_probe+0x1b4/0x218) So reset the atomic state for a given connector by freeing the state pointer and allocate a new empty state object. This can be done using connector funcs->reset helper and has to be done before the hotplug even calls. This patch calls the connector->funcs->reset in panel_bridge_attach. Signed-off-by:
-
Jagan Teki authored
Replace the manual panel handling code by a drm panel_bridge via devm_drm_of_get_bridge(). Adding panel_bridge handling, - Drops drm_connector and related operations as drm_bridge_attach creates connector during attachment. - Drops panel pointer and panel healpers. This simplifies the driver and allows all components in the display pipeline to be treated as bridges. Signed-off-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Add support for the DSI-to-DPI mode. This requires skipping most of the (e)DP initialization code, which is currently a large part of this driver, hence it is better to have far simpler separate tc_dpi_bridge_funcs and their implementation. The configuration of DPI output is also much simpler. The configuration of the DSI input is rather similar to the other TC bridge chips. The Pixel PLL in DPI output mode does not have the 65..150 MHz limitation imposed on the (e)DP output mode, so this limitation is skipped to permit operating panels with far slower pixel clock, even below 9 MHz. This mode of operation of the PLL is valid and tested. The detection of bridge mode is now added into tc_probe_bridge_mode(), where in case a DPI panel is found on port@1 endpoint@1, the mode is assumed to be DSI-to-DPI. If (e)DP is detected on port@2, the mode is assumed to be DPI-to-(e)DP. The DSI-to-(e)DP mode is not supported due to lack of proper hardware, but this would be some sort of mix between the two aforementioned modes. Reviewed-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Marek Vasut authored
The tc_set_video_mode() sets up both common and (e)DP video mode settings of the bridge chip. Split the function into tc_set_common_video_mode() to set the common settings and tc_set_edp_video_mode() to set the (e)DP specific settings. No functional change. Reviewed-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is currently supported. It is possible to find out the mode in which the bridge should be operated by testing connected endpoints in DT. Port allocation: port@0 - DSI input port@1 - DPI input/output port@2 - eDP output Possible connections: DPI -> port@1 -> port@2 -> eDP :: [port@0 is not connected] DSI -> port@0 -> port@2 -> eDP :: [port@1 is not connected] DSI -> port@0 -> port@1 -> DPI :: [port@2 is not connected] Add function to determine the bridge mode based on connected endpoints. Reviewed-by:
-
Marek Vasut authored
The bridge ops are specific to the bridge configuration, move them into tc_probe_edp_bridge_endpoint() to permit cleaner addition of DSI-to-DPI mode. No functional change. Reviewed-by:
-
Marek Vasut authored
This bit of code is (e)DP and aux I2C link specific, move it into tc_aux_link_setup() to permit cleaner addition of DSI-to-DPI mode. No functional change. Reviewed-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is currently supported. In order to support the rest of the modes without making the tc_probe() overly long, split the bridge endpoint parsing into dedicated function, where the necessary logic to detect the bridge mode based on which endpoints are connected, can be implemented. Reviewed-by:
-
Marek Vasut authored
Implement .atomic_check callback which prevents user space from setting unsupported mode. The tc_edp_common_atomic_check() variant is already prepared for DSI-to-DPI mode addition, which has different frequency limits. Reviewed-by:
-
Marek Vasut authored
Use the atomic version of the enable/disable operations to continue the transition to the atomic API. This will be needed to access the mode from the atomic state. Reviewed-by:
-
Marek Vasut authored
These functions are specific to (e)DP output initialization and operation, add specific tc_edp_ prefix to those functions to discern them from DPI output functions that will be added later in this series. No functional change. Reviewed-by:
-
Marek Vasut authored
It is necessary to specify the number of connected/used DSI data lanes when using the DSI input port of this bridge. Document the 'data-lanes' property of the DSI input port. Reviewed-by:
Rob Herring <robh@kernel.org> Acked-by:
-
Marek Vasut authored
The TC358767/TC358867/TC9595 are all capable of operating in multiple modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Document support for the DPI output port, which can now be connected both as input and output. Acked-by:
-
Lucas Stach authored
When the probe routine fails we also need to clean up the CEC adapter registered in adv7511_cec_init(). Fixes: 3b1b9750 ("drm: adv7511/33: add HDMI CEC support") Signed-off-by:
-
Yang Yingliang authored
Add the missing destroy_workqueue() before return from anx7625_i2c_probe() in the error handling case. Fixes: adca62ec ("drm/bridge: anx7625: Support reading edid through aux channel") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by:
-
Jani Nikula authored
The invalid EDID block filtering uses the number of valid EDID extensions instead of all EDID extensions for looping the extensions in the copy. This is fine, by coincidence, if all the invalid blocks are at the end of the EDID. However, it's completely broken if there are invalid extensions in the middle; the invalid blocks are included and valid blocks are excluded. Fix it by modifying the base block after, not before, the copy. Fixes: 14544d09 ("drm/edid: Only print the bad edid when aborting") Reported-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
-
Maxime Ripard authored
The HVS state configuration is useful when debugging what's going on in the vc4 hardware pipeline. Add an implementation of .atomic_print_state. Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Maxime Ripard authored
None of those helpers modify the pointed data, let's make them const. Acked-by:
-
Maxime Ripard authored
A number of drivers (amdgpu, komeda, vc4, etc.) leverage the drm_private_state structure, but we don't have any infrastructure to provide debugging like we do for the other components state. Let's add an atomic_print_state hook to be consistent. Reviewed-by:
-
Maxime Ripard authored
The DRM_UT_STATE controls whether we're calling drm_atomic_print_new_state() whenever a new state is committed. However, that call is made in the drm_mode_atomic_ioctl(), whereas we have multiple users of the drm_atomic_commit() function in the kernel (framebuffer emulation, drm_atomic_helper_dirtyfb, etc.). This leads to multiple states being committed but never actually displayed even though we asked to have verbose atomic state debugging. Let's move the call to drm_atomic_print_new_state() to drm_atomic_commit() to make sure we don't miss any. Non-blocking commits were never logged though, and it would create too much churn in the logs to do so, so leave them out for now. Signed-off-by:
-
- 30 Mar, 2022 1 commit
-
-
Matthias Kaehlcke authored
Two digits are swapped in the AUO B133UAN01 panel id (0x8495 instead of 0x8594). This went initially unnoticed because the panel is still detected, though it is set up with a conservative default timing. Fix the digit swap. Fixes: ec57376f ("drm/panel-edp: Add AUO B133UAN01") Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
- 29 Mar, 2022 1 commit
-
-
Matthias Kaehlcke authored
Add support for the AUO B133UAN01 13.3" WUXGA panel. Signed-off-by:
-
