- 11 Apr, 2017 16 commits
-
-
Jiri Slaby authored
-
Richard Genoud authored
commit 31ca2c63 upstream. If uart_flush_buffer() is called between atmel_tx_dma() and atmel_complete_tx_dma(), the circular buffer has been cleared, but not atmel_port->tx_len. That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE - atmel_port->tx_len) bytes). Tested-by:
Nicolas Ferre <nicolas.ferre@microchip.com> [rg] backport to 3.12 Signed-off-by:
Richard Genoud <richard.genoud@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Akinobu Mita authored
commit 9723ddc8 upstream. This driver reports misc scan input events on the sensor's status register changes. But the event capability for them was not set in the device initialization, so these events were ignored. This change adds the missing event capability. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by:
-
Akinobu Mita authored
commit 08fea55e upstream. This driver reports input events on their interrupts which are triggered by the sensor's status register changes. But only single bit change is reported in the interrupt handler. So if there are multiple bits are changed at almost the same time, other press or release events are ignored. This fixes it by detecting all changed bits in the status register. Signed-off-by:
-
Maxime Ripard authored
commit 259b77ef upstream. The TCA8418 might be used using different interrupt triggers on various boards. This is not working so far because the current code forces a falling edge trigger. The device tree already provides a trigger type, so let's use whatever it sets up, and since we can be loaded without DT, keep the old behaviour for the non-DT case. Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Raphael Assenat authored
commit 45536d37 upstream. Postpone axis initialization to the first open instead of doing it in joydev_connect. This is to make sure the generated startup events are representative of the current joystick state rather than what it was when joydev_connect() was called, potentially much earlier. Once the first user is connected to joydev node we'll be updating joydev->abs[] values and subsequent clients will be getting correct initial states as well. This solves issues with joystick driven menus that start scrolling up each time they are started, until the user moves the joystick to generate events. In emulator menu setups where the menu program is restarted every time the game exits, the repeated need to move the joystick to stop the unintended scrolling gets old rather quickly... Signed-off-by:
Raphael Assenat <raph@raphnet.net> Signed-off-by:
-
Brendan McGrath authored
commit a89af4ab upstream. Support for the Asus Touchpad was recently added. It turns out this device can fail initialisation (and become unusable) when the RESET command is sent too soon after the POWER ON command. Unfortunately the i2c-hid specification does not specify the need for a delay between these two commands. But it was discovered the Windows driver has a 1ms delay. As a result, this patch modifies the i2c-hid module to add a sleep inbetween the POWER ON and RESET commands which lasts between 1ms and 5ms. See https://github.com/vlasenko/hid-asus-dkms/issues/24 for further details. Signed-off-by:
Brendan McGrath <redmcg@redmandi.dyndns.org> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Colin Ian King authored
commit ed9ab428 upstream. Quirking the following AMI USB device with ALWAYS_POLL fixes an AMI virtual keyboard and mouse from not responding and timing out when it is attached to a ppc64el Power 8 system and when we have some rapid open/closes on the mouse device. usb 1-3: new high-speed USB device number 2 using xhci_hcd usb 1-3: New USB device found, idVendor=046b, idProduct=ff01 usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-3: Product: Virtual Hub usb 1-3: Manufacturer: American Megatrends Inc. usb 1-3: SerialNumber: serial usb 1-3.3: new high-speed USB device number 3 using xhci_hcd usb 1-3.3: New USB device found, idVendor=046b, idProduct=ff31 usb 1-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-3.3: Product: Virtual HardDisk Device usb 1-3.3: Manufacturer: American Megatrends Inc. usb 1-3.4: new low-speed USB device number 4 using xhci_hcd usb 1-3.4: New USB device found, idVendor=046b, idProduct=ff10 usb 1-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-3.4: Product: Virtual Keyboard and Mouse usb 1-3.4: Manufacturer: American Megatrends Inc. With the quirk I have not been able to trigger the issue with half an hour of saturation soak testing. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Ardinartsev Nikita authored
commit 877a021e upstream. With NOGET quirk Logitech F510 is now fully workable in dinput mode including rumble effects (according to fftest). Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117091 [jkosina@suse.cz: fix patch format] Signed-off-by:
Ardinartsev Nikita <ardinar23@gmail.com> Acked-by:
-
Andrew Lunn authored
commit 4eba7bb1 upstream. When a multicast group is joined on a socket, a struct ip_mc_socklist is appended to the sockets mc_list containing information about the joined group. If the interface is hot unplugged, this entry becomes stale. Prior to commit 52ad353a ("igmp: fix the problem when mc leave group") it was possible to remove the stale entry by performing a IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on the interface. However, this fix enforces that the interface must still exist. Thus with time, the number of stale entries grows, until sysctl_igmp_max_memberships is reached and then it is not possible to join and more groups. The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is performed without specifying the interface, either by ifindex or ip address. However here we do supply one of these. So loosen the restriction on device existence to only apply when the interface has not been specified. This then restores the ability to clean up the stale entries. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Fixes: 52ad353a "(igmp: fix the problem when mc leave group") Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Ludovic Desroches authored
commit a9bed6b1 upstream. In some cases, we could start a new i2c transfer with the RXRDY flag set. It is not a clean state and it leads to print annoying error messages even if there no real issue. The cause is only having garbage data in the Receive Holding Register because of a weird behavior of the RXRDY flag. Reported-by:
Peter Rosin <peda@lysator.liu.se> Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Fixes: 93563a6a ("i2c: at91: fix a race condition when using the DMA controller") Signed-off-by:
-
Alan Stern authored
commit 7d8021c9 upstream. This patch fixes a bug introduced by commit 977dcfdc ("USB: OHCI: don't lose track of EDs when a controller dies"). The commit changed ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had been called. The user-visible consequence is that the driver occasionally crashes or locks up when an URB is submitted while another URB for the same endpoint is being unlinked. This patch moves the ED state change later, to the right place. The drawback is that now we may unnecessarily execute some instructions multiple times when a controller dies. Since controllers dying is an exceptional occurrence, a little wasted time won't matter. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Heiko Przybyl <lil_tux@web.de> Tested-by:
-
Rafael J. Wysocki authored
commit 0294112e upstream. This effectively reverts the following three commits: 7bc10388 ACPI / resources: free memory on error in add_region_before() 0f1b414d ACPI / PNP: Avoid conflicting resource reservations b9a5e5e1 ACPI / init: Fix the ordering of acpi_reserve_resources() (commit b9a5e5e1 introduced regressions some of which, but not all, were addressed by commit 0f1b414d and commit 7bc10388 was a fixup on top of the latter) and causes ACPI fixed hardware resources to be reserved at the fs_initcall_sync stage of system initialization. The story is as follows. First, a boot regression was reported due to an apparent resource reservation ordering change after a commit that shouldn't lead to such changes. Investigation led to the conclusion that the problem happened because acpi_reserve_resources() was executed at the device_initcall() stage of system initialization which wasn't strictly ordered with respect to driver initialization (and with respect to the initialization of the pcieport driver in particular), so a random change causing the device initcalls to be run in a different order might break things. The response to that was to attempt to run acpi_reserve_resources() as soon as we knew that ACPI would be in use (commit b9a5e5e1). However, that turned out to be too early, because it caused resource reservations made by the PNP system driver to fail on at least one system and that failure was addressed by commit 0f1b414d. That fix still turned out to be insufficient, though, because calling acpi_reserve_resources() before the fs_initcall stage of system initialization caused a boot regression to happen on the eCAFE EC-800-H20G/S netbook. That meant that we only could call acpi_reserve_resources() at the fs_initcall initialization stage or later, but then we might just as well call it after the PNP initalization in which case commit 0f1b414d wouldn't be necessary any more. For this reason, the changes made by commit 0f1b414d are reverted (along with a memory leak fixup on top of that commit), the changes made by commit b9a5e5e1 that went too far are reverted too and acpi_reserve_resources() is changed into fs_initcall_sync, which will cause it to be executed after the PNP subsystem initialization (which is an fs_initcall) and before device initcalls (including the pcieport driver initialization) which should avoid the initial issue. Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581 Link: http://marc.info/?t=143092384600002&r=1&w=2 Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831 Link: http://marc.info/?t=143389402600001&r=1&w=2 Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" Reported-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dan Carpenter authored
commit 7bc10388 upstream. There is a small memory leak on error. Fixes: 0f1b414d (ACPI / PNP: Avoid conflicting resource reservations) Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 0f1b414d upstream. Commit b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" overlooked the fact that the memory and/or I/O regions reserved by acpi_reserve_resources() may conflict with those reserved by the PNP "system" driver. If that conflict actually takes place, it causes the reservations made by the "system" driver to fail while before commit b9a5e5e1 all reservations made by it and by acpi_reserve_resources() would be successful. In turn, that allows the resources that haven't been reserved by the "system" driver to be used by others (e.g. PCI) which sometimes leads to functional problems (up to and including boot failures). To fix that issue, introduce a common resource reservation routine, acpi_reserve_region(), to be used by both acpi_reserve_resources() and the "system" driver, that will track all resources reserved by it and avoid making conflicting requests. Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831 Link: http://marc.info/?t=143389402600001&r=1&w=2 Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" Reported-by:
-
Viresh Kumar authored
commit 92c14bd9 upstream. This is only relevant to implementations with multiple clusters, where clusters have separate clock lines but all CPUs within a cluster share it. Consider a dual cluster platform with 2 cores per cluster. During suspend we start hot unplugging CPUs in order 1 to 3. When CPU2 is removed, policy->kobj would be moved to CPU3 and when CPU3 goes down we wouldn't free policy or its kobj as we want to retain permissions/values/etc. Now on resume, we will get CPU2 before CPU3 and will call __cpufreq_add_dev(). We will recover the old policy and update policy->cpu from 3 to 2 from update_policy_cpu(). But the kobj is still tied to CPU3 and isn't moved to CPU2. We wouldn't create a link for CPU2, but would try that for CPU3 while bringing it online. Which will report errors as CPU3 already has kobj assigned to it. This bug got introduced with commit 42f921a6, which overlooked this scenario. To fix this, lets move kobj to the new policy->cpu while bringing first CPU of a cluster back. Also do a WARN_ON() if kobject_move failed, as we would reach here only for the first CPU of a non-boot cluster. And we can't recover from this situation, if kobject_move() fails. Fixes: 42f921a6 (cpufreq: remove sysfs files for CPUs which failed to come back after resume) Reported-and-tested-by:
Bu Yitian <ybu@qti.qualcomm.com> Reported-by:
Saravana Kannan <skannan@codeaurora.org> Reviewed-by:
Srivatsa S. Bhat <srivatsa@mit.edu> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
- 10 Apr, 2017 12 commits
-
-
Rafael J. Wysocki authored
commit d4faadd5 upstream. Commit 2167e239 (cpufreq: fix garbage kobjects on errors during suspend/resume) breaks suspend/resume on Martin Ziegler's system (hard lockup during resume), so revert it. Fixes: 2167e239 (cpufreq: fix garbage kobjects on errors during suspend/resume) References: https://bugzilla.kernel.org/show_bug.cgi?id=66751Reported-by:
Martin Ziegler <ziegler@uni-freiburg.de> Signed-off-by:
-
Takashi Iwai authored
commit f363a066 upstream. In the commit [15c75b09: ALSA: ctxfi: Fallback DMA mask to 32bit], I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while cthw20k2.c is OK). This patch fixes that obvious bug. (As a side note: although the original commit was completely wrong, it's still working for most of machines, as it sets to 32bit DMA mask in the end. So the bug severity is low.) Fixes: 15c75b09 ("ALSA: ctxfi: Fallback DMA mask to 32bit") Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 15c75b09 upstream. Currently ctxfi driver tries to set only the 64bit DMA mask on 64bit architectures, and bails out if it fails. This causes a problem on some platforms since the 64bit DMA isn't always guaranteed. We should fall back to the default 32bit DMA when 64bit DMA fails. Fixes: 6d74b86d ("ALSA: ctxfi - Allow 64bit DMA") Signed-off-by:
-
Jason A. Donenfeld authored
commit de5540d0 upstream. Under extremely heavy uses of padata, crashes occur, and with list debugging turned on, this happens instead: [87487.298728] WARNING: CPU: 1 PID: 882 at lib/list_debug.c:33 __list_add+0xae/0x130 [87487.301868] list_add corruption. prev->next should be next (ffffb17abfc043d0), but was ffff8dba70872c80. (prev=ffff8dba70872b00). [87487.339011] [<ffffffff9a53d075>] dump_stack+0x68/0xa3 [87487.342198] [<ffffffff99e119a1>] ? console_unlock+0x281/0x6d0 [87487.345364] [<ffffffff99d6b91f>] __warn+0xff/0x140 [87487.348513] [<ffffffff99d6b9aa>] warn_slowpath_fmt+0x4a/0x50 [87487.351659] [<ffffffff9a58b5de>] __list_add+0xae/0x130 [87487.354772] [<ffffffff9add5094>] ? _raw_spin_lock+0x64/0x70 [87487.357915] [<ffffffff99eefd66>] padata_reorder+0x1e6/0x420 [87487.361084] [<ffffffff99ef0055>] padata_do_serial+0xa5/0x120 padata_reorder calls list_add_tail with the list to which its adding locked, which seems correct: spin_lock(&squeue->serial.lock); list_add_tail(&padata->list, &squeue->serial.list); spin_unlock(&squeue->serial.lock); This therefore leaves only place where such inconsistency could occur: if padata->list is added at the same time on two different threads. This pdata pointer comes from the function call to padata_get_next(pd), which has in it the following block: next_queue = per_cpu_ptr(pd->pqueue, cpu); padata = NULL; reorder = &next_queue->reorder; if (!list_empty(&reorder->list)) { padata = list_entry(reorder->list.next, struct padata_priv, list); spin_lock(&reorder->lock); list_del_init(&padata->list); atomic_dec(&pd->reorder_objects); spin_unlock(&reorder->lock); pd->processed++; goto out; } out: return padata; I strongly suspect that the problem here is that two threads can race on reorder list. Even though the deletion is locked, call to list_entry is not locked, which means it's feasible that two threads pick up the same padata object and subsequently call list_add_tail on them at the same time. The fix is thus be hoist that lock outside of that block. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Acked-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
David Hildenbrand authored
commit 90db1043 upstream. No caller currently checks the return value of kvm_io_bus_unregister_dev(). This is evil, as all callers silently go on freeing their device. A stale reference will remain in the io_bus, getting at least used again, when the iobus gets teared down on kvm_destroy_vm() - leading to use after free errors. There is nothing the callers could do, except retrying over and over again. So let's simply remove the bus altogether, print an error and make sure no one can access this broken bus again (returning -ENOMEM on any attempt to access it). Fixes: e93f8a0f ("KVM: convert io_bus to SRCU") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Reviewed-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 3bd32722 upstream. On some QNAP NAS devices the rtc can wake the machine. Several people noticed that once the machine was woken this way it fails to shut down. That's because the driver fails to acknowledge the interrupt and so it keeps active and restarts the machine immediatly after shutdown. See https://bugs.debian.org/794266 for a bug report. Doing this correctly requires to interpret the INT2 flag of the first read of the STATUS1 register because this bit is cleared by read. Note this is not maximally robust though because a pending irq isn't detected when the STATUS1 register was already read (and so INT2 is not set) but the irq was not disabled. But that is a hardware imposed problem that cannot easily be fixed by software. Signed-off-by:
Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 8e6583f1 upstream. There were two deviations from the reference manual: you have to wait half a second when POC is active and you might have to repeat initialization when POC or BLD are still set after the sequence. Note however that as POC and BLD are cleared by read the driver might not be able to detect that a reset is necessary. I don't have a good idea how to fix this. Additionally report the value read from STATUS1 to the caller. This prepares the next patch. Signed-off-by:
-
Uwe Kleine-König authored
The rtc core calls the .read_alarm with all fields initialized to 0. As the s35390a driver doesn't touch some fields the returned date is interpreted as a date in January 1900. So make sure all fields are set to -1; some of them are then overwritten with the right data depending on the hardware state. In mainline this is done by commit d68778b8 ("rtc: initialize output parameter for read alarm to "uninitialized"") in the core. This is considered to dangerous for stable as it might have side effects for other rtc drivers that might for example rely on alarm->time.tm_sec being initialized to 0. Signed-off-by:
-
Uwe Kleine-König authored
commit f87e904d upstream. There are several issues fixed in this patch: - When alarm isn't enabled, set .enabled to zero instead of returning -EINVAL. - Ignore how IRQ1 is configured when determining if IRQ2 is on. - The three alarm registers have an enable flag which must be evaluated. - The chip always triggers when the seconds register gets 0. Note that the rtc framework however doesn't handle the result correctly because it doesn't check wday being initialized and so interprets an alarm being set for 10:00 AM in three days as 10:00 AM tomorrow (or today if that's not over yet). Signed-off-by:
-
Naoya Horiguchi authored
commit c9d398fa upstream. I found the race condition which triggers the following bug when move_pages() and soft offline are called on a single hugetlb page concurrently. Soft offlining page 0x119400 at 0x700000000000 BUG: unable to handle kernel paging request at ffffea0011943820 IP: follow_huge_pmd+0x143/0x190 PGD 7ffd2067 PUD 7ffd1067 PMD 0 [61163.582052] Oops: 0000 [#1] SMP Modules linked in: binfmt_misc ppdev virtio_balloon parport_pc pcspkr i2c_piix4 parport i2c_core acpi_cpufreq ip_tables xfs libcrc32c ata_generic pata_acpi virtio_blk 8139too crc32c_intel ata_piix serio_raw libata virtio_pci 8139cp virtio_ring virtio mii floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: cap_check] CPU: 0 PID: 22573 Comm: iterate_numa_mo Tainted: P OE 4.11.0-rc2-mm1+ #2 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:follow_huge_pmd+0x143/0x190 RSP: 0018:ffffc90004bdbcd0 EFLAGS: 00010202 RAX: 0000000465003e80 RBX: ffffea0004e34d30 RCX: 00003ffffffff000 RDX: 0000000011943800 RSI: 0000000000080001 RDI: 0000000465003e80 RBP: ffffc90004bdbd18 R08: 0000000000000000 R09: ffff880138d34000 R10: ffffea0004650000 R11: 0000000000c363b0 R12: ffffea0011943800 R13: ffff8801b8d34000 R14: ffffea0000000000 R15: 000077ff80000000 FS: 00007fc977710740(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffea0011943820 CR3: 000000007a746000 CR4: 00000000001406f0 Call Trace: follow_page_mask+0x270/0x550 SYSC_move_pages+0x4ea/0x8f0 SyS_move_pages+0xe/0x10 do_syscall_64+0x67/0x180 entry_SYSCALL64_slow_path+0x25/0x25 RIP: 0033:0x7fc976e03949 RSP: 002b:00007ffe72221d88 EFLAGS: 00000246 ORIG_RAX: 0000000000000117 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc976e03949 RDX: 0000000000c22390 RSI: 0000000000001400 RDI: 0000000000005827 RBP: 00007ffe72221e00 R08: 0000000000c2c3a0 R09: 0000000000000004 R10: 0000000000c363b0 R11: 0000000000000246 R12: 0000000000400650 R13: 00007ffe72221ee0 R14: 0000000000000000 R15: 0000000000000000 Code: 81 e4 ff ff 1f 00 48 21 c2 49 c1 ec 0c 48 c1 ea 0c 4c 01 e2 49 bc 00 00 00 00 00 ea ff ff 48 c1 e2 06 49 01 d4 f6 45 bc 04 74 90 <49> 8b 7c 24 20 40 f6 c7 01 75 2b 4c 89 e7 8b 47 1c 85 c0 7e 2a RIP: follow_huge_pmd+0x143/0x190 RSP: ffffc90004bdbcd0 CR2: ffffea0011943820 ---[ end trace e4f81353a2d23232 ]--- Kernel panic - not syncing: Fatal exception Kernel Offset: disabled This bug is triggered when pmd_present() returns true for non-present hugetlb, so fixing the present check in follow_huge_pmd() prevents it. Using pmd_present() to determine present/non-present for hugetlb is not correct, because pmd_present() checks multiple bits (not only _PAGE_PRESENT) for historical reason and it can misjudge hugetlb state. Fixes: e66f17ff ("mm/hugetlb: take page table lock in follow_huge_pmd()") Link: http://lkml.kernel.org/r/1490149898-20231-1-git-send-email-n-horiguchi@ah.jp.nec.comSigned-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by:
Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Peter Xu authored
commit df630b8c upstream. When releasing the bus, let's clear the bus pointers to mark it out. If any further device unregister happens on this bus, we know that we're done if we found the bus being released already. Signed-off-by:
Peter Xu <peterx@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Alan Stern authored
commit 16336820 upstream. Using KASAN, Dmitry found a bug in the rh_call_control() routine: If buffer allocation fails, the routine returns immediately without unlinking its URB from the control endpoint, eventually leading to linked-list corruption. This patch fixes the problem by jumping to the end of the routine (where the URB is unlinked) when an allocation failure occurs. Signed-off-by:
-
- 07 Apr, 2017 12 commits
-
-
Josh Poimboeuf authored
commit 61b79e16 upstream. Paul Menzel reported a warning: WARNING: CPU: 0 PID: 774 at /build/linux-ROBWaj/linux-4.9.13/kernel/trace/trace_functions_graph.c:233 ftrace_return_to_handler+0x1aa/0x1e0 Bad frame pointer: expected f6919d98, received f6919db0 from func acpi_pm_device_sleep_wake return to c43b6f9d The warning means that function graph tracing is broken for the acpi_pm_device_sleep_wake() function. That's because the ACPI Makefile unconditionally sets the '-Os' gcc flag to optimize for size. That's an issue because mcount-based function graph tracing is incompatible with '-Os' on x86, thanks to the following gcc bug: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=42109 I have another patch pending which will ensure that mcount-based function graph tracing is never used with CONFIG_CC_OPTIMIZE_FOR_SIZE on x86. But this patch is needed in addition to that one because the ACPI Makefile overrides that config option for no apparent reason. It has had this flag since the beginning of git history, and there's no related comment, so I don't know why it's there. As far as I can tell, there's no reason for it to be there. The appropriate behavior is for it to honor CONFIG_CC_OPTIMIZE_FOR_{SIZE,PERFORMANCE} like the rest of the kernel. Reported-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Takashi Iwai authored
commit 2d7d5400 upstream. When a new event is queued while processing to resize the FIFO in snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool that is being queued gets removed. For avoiding this race, we need to close the pool to be deleted and sync its usage before actually deleting it. The issue was spotted by syzkaller. Reported-by:
-
John Garry authored
commit 9702c67c upstream. The total ata xfer length may not be calculated properly, in that we do not use the proper method to get an sg element dma length. According to the code comment, sg_dma_len() should be used after dma_map_sg() is called. This issue was found by turning on the SMMUv3 in front of the hisi_sas controller in hip07. Multiple sg elements were being combined into a single element, but the original first element length was being use as the total xfer length. Fixes: ff2aeb1e ("libata: convert to chained sg") Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
James Bottomley authored
commit ffb58456 upstream. mpt3sas has a firmware failure where it can only handle one pass through ATA command at a time. If another comes in, contrary to the SAT standard, it will hang until the first one completes (causing long commands like secure erase to timeout). The original fix was to block the device when an ATA command came in, but this caused a regression with commit 669f0441 Author: Bart Van Assche <bart.vanassche@sandisk.com> Date: Tue Nov 22 16:17:13 2016 -0800 scsi: srp_transport: Move queuecommand() wait code to SCSI core So fix the original fix of the secure erase timeout by properly returning SAM_STAT_BUSY like the SAT recommends. The original patch also had a concurrency problem since scsih_qcmd is lockless at that point (this is fixed by using atomic bitops to set and test the flag). [mkp: addressed feedback wrt. test_bit and fixed whitespace] Fixes: 18f6084a (mpt3sas: Fix secure erase premature termination) Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Acked-by:
Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reported-by:
Ingo Molnar <mingo@kernel.org> Tested-by:
-
Ilya Dryomov authored
commit 633ee407 upstream. sock_alloc_inode() allocates socket+inode and socket_wq with GFP_KERNEL, which is not allowed on the writeback path: Workqueue: ceph-msgr con_work [libceph] ffff8810871cb018 0000000000000046 0000000000000000 ffff881085d40000 0000000000012b00 ffff881025cad428 ffff8810871cbfd8 0000000000012b00 ffff880102fc1000 ffff881085d40000 ffff8810871cb038 ffff8810871cb148 Call Trace: [<ffffffff816dd629>] schedule+0x29/0x70 [<ffffffff816e066d>] schedule_timeout+0x1bd/0x200 [<ffffffff81093ffc>] ? ttwu_do_wakeup+0x2c/0x120 [<ffffffff81094266>] ? ttwu_do_activate.constprop.135+0x66/0x70 [<ffffffff816deb5f>] wait_for_completion+0xbf/0x180 [<ffffffff81097cd0>] ? try_to_wake_up+0x390/0x390 [<ffffffff81086335>] flush_work+0x165/0x250 [<ffffffff81082940>] ? worker_detach_from_pool+0xd0/0xd0 [<ffffffffa03b65b1>] xlog_cil_force_lsn+0x81/0x200 [xfs] [<ffffffff816d6b42>] ? __slab_free+0xee/0x234 [<ffffffffa03b4b1d>] _xfs_log_force_lsn+0x4d/0x2c0 [xfs] [<ffffffff811adc1e>] ? lookup_page_cgroup_used+0xe/0x30 [<ffffffffa039a723>] ? xfs_reclaim_inode+0xa3/0x330 [xfs] [<ffffffffa03b4dcf>] xfs_log_force_lsn+0x3f/0xf0 [xfs] [<ffffffffa039a723>] ? xfs_reclaim_inode+0xa3/0x330 [xfs] [<ffffffffa03a62c6>] xfs_iunpin_wait+0xc6/0x1a0 [xfs] [<ffffffff810aa250>] ? wake_atomic_t_function+0x40/0x40 [<ffffffffa039a723>] xfs_reclaim_inode+0xa3/0x330 [xfs] [<ffffffffa039ac07>] xfs_reclaim_inodes_ag+0x257/0x3d0 [xfs] [<ffffffffa039bb13>] xfs_reclaim_inodes_nr+0x33/0x40 [xfs] [<ffffffffa03ab745>] xfs_fs_free_cached_objects+0x15/0x20 [xfs] [<ffffffff811c0c18>] super_cache_scan+0x178/0x180 [<ffffffff8115912e>] shrink_slab_node+0x14e/0x340 [<ffffffff811afc3b>] ? mem_cgroup_iter+0x16b/0x450 [<ffffffff8115af70>] shrink_slab+0x100/0x140 [<ffffffff8115e425>] do_try_to_free_pages+0x335/0x490 [<ffffffff8115e7f9>] try_to_free_pages+0xb9/0x1f0 [<ffffffff816d56e4>] ? __alloc_pages_direct_compact+0x69/0x1be [<ffffffff81150cba>] __alloc_pages_nodemask+0x69a/0xb40 [<ffffffff8119743e>] alloc_pages_current+0x9e/0x110 [<ffffffff811a0ac5>] new_slab+0x2c5/0x390 [<ffffffff816d71c4>] __slab_alloc+0x33b/0x459 [<ffffffff815b906d>] ? sock_alloc_inode+0x2d/0xd0 [<ffffffff8164bda1>] ? inet_sendmsg+0x71/0xc0 [<ffffffff815b906d>] ? sock_alloc_inode+0x2d/0xd0 [<ffffffff811a21f2>] kmem_cache_alloc+0x1a2/0x1b0 [<ffffffff815b906d>] sock_alloc_inode+0x2d/0xd0 [<ffffffff811d8566>] alloc_inode+0x26/0xa0 [<ffffffff811da04a>] new_inode_pseudo+0x1a/0x70 [<ffffffff815b933e>] sock_alloc+0x1e/0x80 [<ffffffff815ba855>] __sock_create+0x95/0x220 [<ffffffff815baa04>] sock_create_kern+0x24/0x30 [<ffffffffa04794d9>] con_work+0xef9/0x2050 [libceph] [<ffffffffa04aa9ec>] ? rbd_img_request_submit+0x4c/0x60 [rbd] [<ffffffff81084c19>] process_one_work+0x159/0x4f0 [<ffffffff8108561b>] worker_thread+0x11b/0x530 [<ffffffff81085500>] ? create_worker+0x1d0/0x1d0 [<ffffffff8108b6f9>] kthread+0xc9/0xe0 [<ffffffff8108b630>] ? flush_kthread_worker+0x90/0x90 [<ffffffff816e1b98>] ret_from_fork+0x58/0x90 [<ffffffff8108b630>] ? flush_kthread_worker+0x90/0x90 Use memalloc_noio_{save,restore}() to temporarily force GFP_NOIO here. Link: http://tracker.ceph.com/issues/19309Reported-by:
Sergey Jerusalimov <wintchester@gmail.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 619bd4a7 upstream. Since the change in commit: fd7a4bed ("sched, rt: Convert switched_{from, to}_rt() / prio_changed_rt() to balance callbacks") ... we don't reschedule a task under certain circumstances: Lets say task-A, SCHED_OTHER, is running on CPU0 (and it may run only on CPU0) and holds a PI lock. This task is removed from the CPU because it used up its time slice and another SCHED_OTHER task is running. Task-B on CPU1 runs at RT priority and asks for the lock owned by task-A. This results in a priority boost for task-A. Task-B goes to sleep until the lock has been made available. Task-A is already runnable (but not active), so it receives no wake up. The reality now is that task-A gets on the CPU once the scheduler decides to remove the current task despite the fact that a high priority task is enqueued and waiting. This may take a long time. The desired behaviour is that CPU0 immediately reschedules after the priority boost which made task-A the task with the lowest priority. [js] no deadline in 3.12 yet Suggested-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Dave Martin authored
commit 7195ee31 upstream. It's not clear what behaviour is sensible when doing partial write of NT_METAG_RPIPE, so just don't bother. This patch assumes that userspace will never rely on a partial SETREGSET in this case, since it's not clear what should happen anyway. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Acked-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Dave Martin authored
commit 5fe81fe9 upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill TXSTATUS, a well-defined default value is used, based on the task's current value. Suggested-by:
-
Dave Martin authored
commit a78ce80d upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Signed-off-by:
-
Dave Martin authored
commit d3805c54 upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Signed-off-by:
-
Dave Martin authored
commit fb411b83 upstream. gpr_set won't work correctly and can never have been tested, and the correct behaviour is not clear due to the endianness-dependent task layout. So, just remove it. The core code will now return -EOPNOTSUPPORT when trying to set NT_PRSTATUS on this architecture until/unless a correct implementation is supplied. Signed-off-by:
-
Ladi Prosek authored
commit fc865322 upstream. When init_vqs runs, virtio_balloon.stats is either uninitialized or contains stale values. The host updates its state with garbage data because it has no way of knowing that this is just a marker buffer used for signaling. This patch updates the stats before pushing the initial buffer. Alternative fixes: * Push an empty buffer in init_vqs. Not easily done with the current virtio implementation and violates the spec "Driver MUST supply the same subset of statistics in all buffers submitted to the statsq". * Push a buffer with invalid tags in init_vqs. Violates the same spec clause, plus "invalid tag" is not really defined. Note: the spec says: When using the legacy interface, the device SHOULD ignore all values in the first buffer in the statsq supplied by the driver after device initialization. Note: Historically, drivers supplied an uninitialized buffer in the first buffer. Unfortunately QEMU does not seem to implement the recommendation even for the legacy interface. Signed-off-by:
Ladi Prosek <lprosek@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
