Some versions of the firmware for the sc7280-idp  board FIFO mode
disabled and must thus use GPI DMA. Enable gpi_dma0 and gpi_dma1 to
allow this.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-3-vkoul@kernel.org

The GENI I2C and SPI controllers may use the GPI DMA engine, define the
rx and tx channels for these controllers to enable this.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-2-vkoul@kernel.org

The Qualcomm SC7280 has two GPI DMAengines, add definitions for these.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-1-vkoul@kernel.org

Fix the following 'make dtbs_check' warning(s) by
using phy@ instead of lanes@:
arch/arm64/boot/dts/qcom/sm8450-hdk.dtb: phy@1c0f000: 'lanes@1c0e000'
  does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220418205509.1102109-5-bhupesh.sharma@linaro.org

Add support for onboard MCP2517FD SPI CAN transceiver attached to
SPI0 of RB3.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421073438.1824061-1-vkoul@kernel.org

Per DT spec node names should not have underscores (_) in them, so
change can_clock to can-clock.

Fixes: 5c44c564 ("arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421073502.1824089-1-vkoul@kernel.org

Enable the two SAR sensors of the CRD based on herobrine.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415172238.1.I671bdf40fdfce7a35f6349fca0dc56145d4210ee@changeid

sm8250 has two CCI busses with two I2C busses apiece.
Co-developed-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Julian Grahsl <jgrahsl@snap.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415164655.1679628-4-bryan.odonoghue@linaro.org

Adds a CAMSS definition block.
Co-developed-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415164655.1679628-3-bryan.odonoghue@linaro.org

Add the camcc DT node for the Camera Clock Controller on sm8250.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415164655.1679628-2-bryan.odonoghue@linaro.org

Enable the i2c5, spi4, spi18 and spi19 nodes which were tested on qrd
board along with related qup nodes and gpi_dma0
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-8-vkoul@kernel.org

qupv3_id_1 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.

Fixes: 5188049c ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-7-vkoul@kernel.org

qup2 has 7 SEs, so add the SEs (i2c and spi) along with pinconf for
these SEs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-6-vkoul@kernel.org

qup1 has 7 SEs, I2C13 and I2C14 were already added so added the
remaining SEs (i2c and spi) along with pinconf for these SEs
Also add interconnect properties for I2C13 and I2C14
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-5-vkoul@kernel.org

qup0 has 7 SEs, with SE7 as uart and already added, so add the
remaining 6 SEs (i2c and spi) along with pinconf for these SEs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-4-vkoul@kernel.org

qupv3_id_0 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.

While at it also add interconnect nodes for qup

Fixes: 5188049c ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-3-vkoul@kernel.org

GPI DMA can be used for DMA operations for QUP devices, so add the three
gpi_dma insances found in this SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-2-vkoul@kernel.org

Some versions of the firmware for the SM8350 Hardware Development Kit
(HDK) has FIFO mode disabled for i2c13 and must thus use GPI DMA. Enable
&gpi_dma1 to allow this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-3-bjorn.andersson@linaro.org

The GENI I2C and SPI controllers may use the GPI DMA engine, define the
rx and tx channels for these controllers to enable this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-2-bjorn.andersson@linaro.org

The Qualcomm SM8350 has three GPI DMA engines, add definitions for
these.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-1-bjorn.andersson@linaro.org

Adding wakeup-source property for USB controller in SC7280.
This property is added to inform that the USB controller is
wake up capable and to conditionally power down the phy during
system suspend.
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1649704614-31518-7-git-send-email-quic_c_sanm@quicinc.com

Using node paths to extend or override a device tree node is error
prone.  If there was a typo error, a new node will be created instead of
extending the existing node.  This will lead to run-time errors that
could be hard to detect.

A mistyped label on the other hand, will cause a dtc compile error
(during build time).  This also reduces the indentation making the code
easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220402192859.154977-2-krzysztof.kozlowski@linaro.org

Using node paths to extend or override a device tree node is error
prone.  If there was a typo error, a new node will be created instead of
extending the existing node.  This will lead to run-time errors that
could be hard to detect.

A mistyped label on the other hand, will cause a dtc compile error
(during build time).  This also reduces the indentation making the code
easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220402192859.154977-1-krzysztof.kozlowski@linaro.org

Xiaomi Poco F1 uses the QCOM WLED driver for backlight control.
Enable and link it to the panel to use it.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB70092607CD7CDD8CF8BCD464D9E09@BY5PR02MB7009.namprd02.prod.outlook.com

Like the c630, the Poco F1 is also capable of using both antenna
channels for 2.4 and 5ghz wifi, however unlike the c630 only the first
channel is used for bluetooth. Similar to Oneplus 6.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB7009E2566F9000F338432761D91F9@BY5PR02MB7009.namprd02.prod.outlook.com

vddio is misspelled with a "0" instead of "o". Fix it.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB7009901651E6A8D5ACB0425ED91F9@BY5PR02MB7009.namprd02.prod.outlook.com

Enable Qualcomm IP Accelerator (IPA) driver for mobile data functionality
which works by using ModemManager.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB7009405D7C06C0B480974063D91F9@BY5PR02MB7009.namprd02.prod.outlook.com

The "qcom/sdm845/" path conflicts with db845c's firmware that are
present in the linux-firmware package. Xiaomi uses their own signed
firmware for Poco F1 and can't use the db845c's firmware. So let's
use "qcom/sdm845/beryllium/" to distinguish Poco F1's firmware files.

For easier handling and packaging, the mdt+bXX files are squashed
using Bjorn Andersson's pil-squasher tool from this link:
https://github.com/andersson/pil-squasherSigned-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB700966DEE6F6044EBEB5B892D91F9@BY5PR02MB7009.namprd02.prod.outlook.com

Align BCM voter node with DT schema by using hyphen instead of
underscore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220411085935.130072-3-krzysztof.kozlowski@linaro.org

Add thermal zones handled by tsens sensors. The definitions and the trip
points were taken from the downstream dts. For the CPU core thermal
sensors, the trip points were changed to follow the example of other
Qualcomm platforms.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410234458.1739279-3-dmitry.baryshkov@linaro.org

The change adds description of two thermal sensor controllers found
on SM8450.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410234458.1739279-2-dmitry.baryshkov@linaro.org

With the gcc driver now being more complete and describing clocks which
might not always be write-accessible to the OS, conservatively specify
all such clocks as protected in the SoC dts.
The board dts - or even user-supplied dts - can override this property
to reflect the actual configuration.
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220411072156.24451-6-michael.srba@seznam.cz

Add definitions of four clocks which need to be manipulated in order to
initialize the AHB bus which exposes the SCC block in the global address
space.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220411072156.24451-2-michael.srba@seznam.cz

The bindings require a fallback compatible to RPM clock controller.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220401201035.189106-4-krzysztof.kozlowski@linaro.org

The Qualcomm SMD does not use qcom,local-pid property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220401201035.189106-3-krzysztof.kozlowski@linaro.org

Align RPM requests node with DT schema by using hyphen instead of
underscore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220401201035.189106-2-krzysztof.kozlowski@linaro.org

Configure regulators used by the wifi hardware and enable it.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325101841.172304-2-luca.weiss@fairphone.com

Add a node describing the wifi hardware found on sm6350.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325101841.172304-1-luca.weiss@fairphone.com

Set the aliases for both SDHCI controllers.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-16-konrad.dybcio@somainline.org