Put an upper bound on how long we will wait for the device to respond to
a read/write request (i.e., 100 milliseconds) and return an error if
this is reached.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The device indicates the result of a read/write operation by making the
status available on a subsequent request from the driver.  This is not
ready immediately, though, so the driver is currently slamming the
device with hundreds of pointless requests before getting the expected
response.  Add a two millisecond delay before each attempt.  This is
approximately the behavior observed with version 4.2.7.1 of the Windows
driver.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The BDW audio firmware DSP manages the DMA and the DMA cannot be
stopped exactly at the end of the playback stream. This means
stale samples may be played at PCM stop unless the driver copies
silence to the subsequent periods.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

BugLink: https://bugs.launchpad.net/bugs/1412800Signed-off-by: TienFu Chen <tienfu.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In 'replace' event data, numerical ID of control is always invalid. This
commit fix this bug so as the event data has renewed numerical ID for
control.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The first URBs are submitted during the prepare stage. When .trigger is
called, the ALSA core saves a trigger tstamp that doesn't correspond to
the actual time when the samples are submitted. The trigger_tstamp is
now updated when the first data are submitted to avoid any time offsets.

A usb-specific trigger_tstamp_pending_update flag is used for now,
at some point the flag would need to move to the ALSA core, USB
is not the only interface where silent block transfers are programmed
as part of the prepare stage, with actual data enabled when .trigger
is called.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Make sure wallclock counter and trigger timestamp are read very
close to each other for better alignment.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Don't use generic snapshot of trigger_tstamp if low-level driver or
hardware can get a more precise value for better audio/system time
synchronization.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

timestamp in RUNNING mode is already taken in update_hw_ptr routine,
getting a new timestamp introduces offset between hw_ptr, audio_tstamp
and system time

Add else condition to read timestamp as fallback and only when
enabled
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The problem here is that we check:

	if (dev >= SNDRV_CARDS)

Then we increment "dev".

       if (!joystick_port[dev++])

Then we use it as an offset into a array with SNDRV_CARDS elements.

	if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {

This has 3 effects:
1) If you use the module option to specify the joystick port then it has
   to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
   32 cards.
3) Static checkers will correctly complain that are off by one.

Fixes: db1005ec ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-v3.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Final updates for v3.20

A few more updates for v3.20 that have accumilated over the second half
of last week.  One new (relatively simple) driver for the Maxim
max98357a and some other driver specific fixes and enhancements.  I did
apply a few patches that haven't been in -next just now before sending
this, all fixes except for one simple device ID addition patch.

Merge remote-tracking branches 'asoc/topic/wm8804', 'asoc/topic/wm8904', 'asoc/topic/wm8960', 'asoc/topic/wm8988' and 'asoc/topic/xtfpga' into asoc-next

Merge remote-tracking branches 'asoc/topic/ts3a227e', 'asoc/topic/ts3a277e' and 'asoc/topic/txx9' into asoc-next

Merge remote-tracking branches 'asoc/topic/simple', 'asoc/topic/sta32x', 'asoc/topic/tdm-slot', 'asoc/topic/tegra' and 'asoc/topic/tlv320aic3x' into asoc-next

Merge remote-tracking branches 'asoc/topic/rt5670', 'asoc/topic/rt5677', 'asoc/topic/rx51', 'asoc/topic/samsung' and 'asoc/topic/sh' into asoc-next

Merge remote-tracking branches 'asoc/topic/pxa', 'asoc/topic/rcar' and 'asoc/topic/rt286' into asoc-next

Merge remote-tracking branches 'asoc/topic/fsl-spdif', 'asoc/topic/imx', 'asoc/topic/intel', 'asoc/topic/jz4740' and 'asoc/topic/max98357a' into asoc-next

Merge remote-tracking branches 'asoc/topic/doc', 'asoc/topic/dwc', 'asoc/topic/fsi', 'asoc/topic/fsl' and 'asoc/topic/fsl-asrc' into asoc-next

Merge remote-tracking branches 'asoc/topic/cs42l73', 'asoc/topic/dai' and 'asoc/topic/davinci' into asoc-next

Merge remote-tracking branches 'asoc/topic/bt-sco', 'asoc/topic/cs35l32', 'asoc/topic/cs42l52' and 'asoc/topic/cs42l56' into asoc-next

Merge remote-tracking branches 'asoc/topic/ad193x', 'asoc/topic/alc5632', 'asoc/topic/atmel' and 'asoc/topic/au1x' into asoc-next

Merge remote-tracking branches 'asoc/fix/ac97', 'asoc/fix/atmel', 'asoc/fix/intel', 'asoc/fix/rt286', 'asoc/fix/rt5640', 'asoc/fix/samsung', 'asoc/fix/sgtl5000', 'asoc/fix/sta32x', 'asoc/fix/tlv320aic3x' and 'asoc/fix/wm8731' into asoc-linus

ASoC: Updates for v3.20

Nothing too exciting here yet, a small optimization for DAPM from
Lars-Peter and a few small bits and pieces for drivers but nothing
that really stands out.

# gpg: Signature made Tue 30 Dec 2014 00:15:48 HKT using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

RT5670 doesn't support auto incrementing writes so driver should
set the use_single_rw flag for regmap.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This patch adds support for rt288 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>

sound/soc/intel/cht_bsw_rt5645.c:315:3-8: No need to set .owner here. The core will do it.

 Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now when the CDCLK I2S output clock can be handled through the clock
API the Odroid X2/U3 can be switched to the simple-audio-card DT binding.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Clock related properties are added to the Exynos4 I2S device nodes
so they can be referred to as clock providers. Missing i2s_opclk1
clock is added to the I2S0 node and clock properties are added
to the MAX98090 codec node to allow it to control/read frequency
of the MCLK clock directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently when adding a new control, the assigned numerical ID is not
set for event data, thus userspace applications cannot realize it just
by event data.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Provide a unique name for each driver instead of using "line6usb" for
all of them.  This will allow for different configurations based on the
driver type.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It is unlikely this function would ever be used in a context without a
pointer to a `struct usb_line6_toneport', so grab the device type from
it rather than having the caller do it.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a predicate for testing if the device supports source selection to
make the conditional logic around this a bit cleaner.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Current snd_soc_unregister_card() indicates unregistered debug
message when it was called. But, it should be called only when
it was really unregistered.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>