The commit c5521189 ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.

Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.

Fixes: c5521189 ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a bug in which the receiving of packets can stop in the zero-copy
driver. Ice HW ignores 3 lower bits from QRX_TAIL register, which means
that tail is bumped only on intervals of 8. Currently with XSK RX
batching in place, ice_alloc_rx_bufs_zc() clears the status_error0 only
of the last descriptor that has been allocated/taken from the XSK buffer
pool. status_error0 includes DD bit that is looked upon by the
ice_clean_rx_irq_zc() to tell if a descriptor can be processed.

The bug can be triggered when driver updates the ntu but not the
QRX_TAIL, so HW wouldn't have a chance to write to the ready
descriptors. Later on driver moves the ntc to the mentioned set of
descriptors and interprets them as a ready to be processed, since
corresponding DD bits were not cleared nor any writeback has happened
that would clear it. This can then lead to ntc == ntu case which means
that ring is empty and no further packet processing.

Fix the XSK traffic hang that can be observed when l2fwd scenario from
xdpsock is used by making sure that status_error0 is cleared for each
descriptor that is fed to HW and therefore we are sure that driver will
not processed non-valid DD bits. This will also prevent the driver from
processing the descriptors that were allocated in favor of the
previously processed ones, but writeback didn't happen yet.

Fixes: db804cfc ("ice: Use the xsk batched rx allocation interface")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.

Use 'bitmap_set()' instead in order not to set unexpected bits.

Fixes: e531f767 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing mutex_unlock before return from function
ocelot_hwstamp_set() in the ocelot_setup_ptp_traps() error
handling case.

Fixes: 96ca08c0 ("net: mscc: ocelot: set up traps for PTP packets")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211129151652.1165433-1-weiyongjun1@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

David Howells says:

====================
rxrpc: Leak fixes

Here are a couple of fixes for leaks in AF_RXRPC:

 (1) Fix a leak of rxrpc_peer structs in rxrpc_look_up_bundle().
 (2) Fix a leak of rxrpc_local structs in rxrpc_lookup_peer().

* tag 'rxrpc-fixes-20211129' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  rxrpc: Fix rxrpc_local leak in rxrpc_lookup_peer()
  rxrpc: Fix rxrpc_peer leak in rxrpc_look_up_bundle()
====================

Link: https://lore.kernel.org/r/163820097905.226370.17234085194655347888.stgit@warthog.procyon.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jason A. Donenfeld says:

====================
wireguard/siphash patches for 5.16-rc

Here's quite a largeish set of stable patches I've had queued up and
testing for a number of months now:

  - Patch (1) squelches a sparse warning by fixing an annotation.
  - Patches (2), (3), and (5) are minor improvements and fixes to the
    test suite.
  - Patch (4) is part of a tree-wide cleanup to have module-specific
    init and exit functions.
  - Patch (6) fixes a an issue with dangling dst references, by having a
    function to release references immediately rather than deferring,
    and adds an associated test case to prevent this from regressing.
  - Patches (7) and (8) help mitigate somewhat a potential DoS on the
    ingress path due to the use of skb_list's locking hitting contention
    on multiple cores by switching to using a ring buffer and dropping
    packets on contention rather than locking up another core spinning.
  - Patch (9) switches kvzalloc to kvcalloc for better form.
  - Patch (10) fixes alignment traps in siphash with clang-13 (and maybe
    other compilers) on armv6, by switching to using the unaligned
    functions by default instead of the aligned functions by default.
====================

Link: https://lore.kernel.org/r/20211129153929.3457-1-Jason@zx2c4.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.

Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.

Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.

This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.

Link: https://lore.kernel.org/linux-arm-kernel/20181008211554.5355-4-ard.biesheuvel@linaro.org/
Link: https://lore.kernel.org/linux-crypto/CAK8P3a2KfmmGDbVHULWevB0hv71P2oi2ZCHEAqT=8dQfa0=cqQ@mail.gmail.com/Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2c956a60 ("siphash: add cryptographically secure PRF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use 2-factor argument form kvcalloc() instead of kvzalloc().

Link: https://github.com/KSPP/linux/issues/162
Fixes: e7096c13 ("net: WireGuard secure network tunnel")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[Jason: Gustavo's link above is for KSPP, but this isn't actually a
 security fix, as table_size is bounded to 8192 anyway, and gcc realizes
 this, so the codegen comes out to be about the same.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If we're being delivered packets from multiple CPUs so quickly that the
ring lock is contended for CPU tries, then it's safe to assume that the
queue is near capacity anyway, so just drop the packet rather than
spinning. This helps deal with multicore DoS that can interfere with
data path performance. It _still_ does not completely fix the issue, but
it again chips away at it.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Fixes: e7096c13 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Apparently the spinlock on incoming_handshake's skb_queue is highly
contended, and a torrent of handshake or cookie packets can bring the
data plane to its knees, simply by virtue of enqueueing the handshake
packets to be processed asynchronously. So, we try switching this to a
ring buffer to hopefully have less lock contention. This alleviates the
problem somewhat, though it still isn't perfect, so future patches will
have to improve this further. However, it at least doesn't completely
diminish the data plane.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Reported-by: Joel Wanner <joel.wanner@inf.ethz.ch>
Fixes: e7096c13 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Each peer's endpoint contains a dst_cache entry that takes a reference
to another netdev. When the containing namespace exits, we take down the
socket and prevent future sockets from being created (by setting
creating_net to NULL), which removes that potential reference on the
netns. However, it doesn't release references to the netns that a netdev
cached in dst_cache might be taking, so the netns still might fail to
exit. Since the socket is gimped anyway, we can simply clear all the
dst_caches (by way of clearing the endpoint src), which will release all
references.

However, the current dst_cache_reset function only releases those
references lazily. But it turns out that all of our usages of
wg_socket_clear_peer_endpoint_src are called from contexts that are not
exactly high-speed or bottle-necked. For example, when there's
connection difficulty, or when userspace is reconfiguring the interface.
And in particular for this patch, when the netns is exiting. So for
those cases, it makes more sense to call dst_release immediately. For
that, we add a small helper function to dst_cache.

This patch also adds a test to netns.sh from Hangbin Liu to ensure this
doesn't regress.
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Fixes: 900575aa ("wireguard: device: avoid circular netns references")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

DEBUG_PI_LIST was renamed to DEBUG_PLIST since 8e18faea ("lib/plist:
rename DEBUG_PI_LIST to DEBUG_PLIST").
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Fixes: 8e18faea ("lib/plist: rename DEBUG_PI_LIST to DEBUG_PLIST")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rename module_init & module_exit functions that are named
"mod_init" and "mod_exit" so that they are unique in both the
System.map file and in initcall_debug output instead of showing
up as almost anonymous "mod_init".

This is helpful for debugging and in determining how long certain
module_init calls take to execute.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We previously removed the restriction on looping to self, and then added
a test to make sure the kernel didn't blow up during a routing loop. The
kernel didn't blow up, thankfully, but on certain architectures where
skb fragmentation is easier, such as ppc64, the skbs weren't actually
being discarded after a few rounds through. But the test wasn't catching
this. So actually test explicitly for massive increases in tx to see if
we have a routing loop. Note that the actual loop problem will need to
be addressed in a different commit.

Fixes: b673e24a ("wireguard: socket: remove errant restriction on looping to self")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The selftests currently parse the kernel log at the end to track
potential memory leaks. With these tests now reading off the end of the
buffer, due to recent optimizations, some creation messages were lost,
making the tests think that there was a free without an alloc. Fix this
by increasing the kernel log size.

Fixes: 24b70eee ("wireguard: use synchronize_net rather than synchronize_rcu")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A __rcu annotation got lost during refactoring, which caused sparse to
become enraged.

Fixes: bf7b042d ("wireguard: allowedips: free empty intermediate nodes when removing single node")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Need to call rxrpc_put_local() for peer candidate before kfree() as it
holds a ref to rxrpc_local.

[DH: v2: Changed to abstract the peer freeing code out into a function]

Fixes: 9ebeddef ("rxrpc: rxrpc_peer needs to hold a ref on the rxrpc_local record")
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/all/20211121041608.133740-2-eiichi.tsukata@nutanix.com/ # v1

Need to call rxrpc_put_peer() for bundle candidate before kfree() as it
holds a ref to rxrpc_peer.

[DH: v2: Changed to abstract out the bundle freeing code into a function]

Fixes: 245500d8 ("rxrpc: Rewrite the client connection manager")
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20211121041608.133740-1-eiichi.tsukata@nutanix.com/ # v1

The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.

After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c4 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").

The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.

How to reproduce:
 - Add the following nftables rule to a prerouting chain:
     meta nfproto ipv6 fib saddr . mark . iif oif missing drop
   This can be done with:
     sudo nft create table inet test
     sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
     sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
 - Run:
     sudo ip -6 rule add table main suppress_prefixlength 0
 - Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
   with every incoming ipv6 packet.

This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.

[1]: https://github.com/torvalds/linux/blob/ca7a03c4175366a92cee0ccc4fec0038c3266e26/net/ipv6/fib6_rules.c#L71
[2]: https://github.com/torvalds/linux/blob/ca7a03c4175366a92cee0ccc4fec0038c3266e26/net/ipv6/fib6_rules.c#L99

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105
Fixes: ca7a03c4 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
net: atlantic: 11-2021 fixes

The patch series contains fixes for atlantic driver to improve support
of latest AQC113 chipset.

Please consider applying it to 'net' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state

Fixes: 508f2e3d ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.

Fixes: 5cfd54d7 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.

Fixes: 071a0204 ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.

Fixes: b3f0c79c ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.

Fixes: c1be0bf0 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.

Fixes: 5cfd54d7 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.

Fixes: 5cfd54d7 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When link modes were initially added in commit 2c762679
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc7
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.

Switch to using more specific link modes added in commit 5711a982
("net: ethtool: add support for 1000BaseX and missing 10G link modes").

Tested with MCX311A-XCAT connected via DAC.
Before:

% sudo ethtool enp3s0
Settings for enp3s0:
	Supported ports: [ FIBRE ]
	Supported link modes:   1000baseKX/Full
	                        10000baseKR/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: No
	Supported FEC modes: Not reported
	Advertised link modes:  1000baseKX/Full
	                        10000baseKR/Full
	Advertised pause frame use: Symmetric
	Advertised auto-negotiation: No
	Advertised FEC modes: Not reported
	Speed: 10000Mb/s
	Duplex: Full
	Auto-negotiation: off
	Port: Direct Attach Copper
	PHYAD: 0
	Transceiver: internal
	Supports Wake-on: d
	Wake-on: d
        Current message level: 0x00000014 (20)
                               link ifdown
	Link detected: yes

With this change:

% sudo ethtool enp3s0
	Settings for enp3s0:
	Supported ports: [ FIBRE ]
	Supported link modes:   1000baseX/Full
	                        10000baseCR/Full
 	                        10000baseSR/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: No
	Supported FEC modes: Not reported
	Advertised link modes:  1000baseX/Full
 	                        10000baseCR/Full
 	                        10000baseSR/Full
	Advertised pause frame use: Symmetric
	Advertised auto-negotiation: No
	Advertised FEC modes: Not reported
	Speed: 10000Mb/s
	Duplex: Full
	Auto-negotiation: off
	Port: Direct Attach Copper
	PHYAD: 0
	Transceiver: internal
	Supports Wake-on: d
	Wake-on: d
        Current message level: 0x00000014 (20)
                               link ifdown
	Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In our test device, we're currently freeing skbs in the transmit path
with kfree(), rather than kfree_skb(). This change uses the correct
kfree_skb() instead.

Fixes: ded21b72 ("mctp: Add test utils")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.

Fixes: f295b3ae ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>

Benjamin Poirier says:

====================
net: mpls: Netlink notification fixes

fix missing or inaccurate route notifications when devices used in
nexthops are deleted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the previous commit, nh_dev can no longer be accessed and
modified concurrently.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
	DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
	NEWROUTE notification is missing entirely
* delete interface of last nexthop
	DELROUTE notification is missing nexthop

All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.

Fixes: f8efb73c ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.

Fixes: cc89c323 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71

Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.

This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.

rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.

Fixes: 4af2950c ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.

The root cause is quite similar to the one addressed by
commit 20eb4f29 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.

The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.

The overall relevant stack trace looks like the following:

httpd 78268 [001] 3461630.850950:      probe:tcp_sendmsg_locked:
        ffffffff91461d91 tcp_sendmsg_locked+0x1
        ffffffff91462b57 tcp_sendmsg+0x27
        ffffffff9139814e sock_sendmsg+0x3e
        ffffffffc06dfe1d smb_send_kvec+0x28
        [...]
        ffffffffc06cfaf8 cifs_readpages+0x213
        ffffffff90e83c4b read_pages+0x6b
        ffffffff90e83f31 __do_page_cache_readahead+0x1c1
        ffffffff90e79e98 filemap_fault+0x788
        ffffffff90eb0458 __do_fault+0x38
        ffffffff90eb5280 do_fault+0x1a0
        ffffffff90eb7c84 __handle_mm_fault+0x4d4
        ffffffff90eb8093 handle_mm_fault+0xc3
        ffffffff90c74f6d __do_page_fault+0x1ed
        ffffffff90c75277 do_page_fault+0x37
        ffffffff9160111e page_fault+0x1e
        ffffffff9109e7b5 copyin+0x25
        ffffffff9109eb40 _copy_from_iter_full+0xe0
        ffffffff91462370 tcp_sendmsg_locked+0x5e0
        ffffffff91462370 tcp_sendmsg_locked+0x5e0
        ffffffff91462b57 tcp_sendmsg+0x27
        ffffffff9139815c sock_sendmsg+0x4c
        ffffffff913981f7 sock_write_iter+0x97
        ffffffff90f2cc56 do_iter_readv_writev+0x156
        ffffffff90f2dff0 do_iter_write+0x80
        ffffffff90f2e1c3 vfs_writev+0xa3
        ffffffff90f2e27c do_writev+0x5c
        ffffffff90c042bb do_syscall_64+0x5b
        ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65

The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.

v1 -> v2:
 - use a stricted sk_page_frag() check instead of reordering the
   code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes: 5640f768 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver assumes that split headers can be enabled/disabled without
stopping/starting the device, so it writes DMA_CHAN_CONTROL from
stmmac_set_features().  However, on my system (IP v5.10a without Split
Header support), simply writing DMA_CHAN_CONTROL when DMA is running
(for example, with the commands below) leads to a TX watchdog timeout.

 host$ socat TCP-LISTEN:1024,fork,reuseaddr - &
 device$ ethtool -K eth0 tso off
 device$ ethtool -K eth0 tso on
 device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024
 <tx watchdog timeout>

Note that since my IP is configured without Split Header support, the
driver always just reads and writes the same value to the
DMA_CHAN_CONTROL register.

I don't have access to any platforms with Split Header support so I
don't know if these writes to the DMA_CHAN_CONTROL while DMA is running
actually work properly on such systems.  I could not find anything in
the databook that says that DMA_CHAN_CONTROL should not be written when
the DMA is running.

But on systems without Split Header support, there is in any case no
need to call enable_sph() in stmmac_set_features() at all since SPH can
never be toggled, so we can avoid the watchdog timeout there by skipping
this call.

Fixes: 8c6fc097 ("net: stmmac: gmac4+: Add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Jakub Kicinski:
 "Networking fixes, including fixes from netfilter.

  Current release - regressions:

   - r8169: fix incorrect mac address assignment

   - vlan: fix underflow for the real_dev refcnt when vlan creation
     fails

   - smc: avoid warning of possible recursive locking

  Current release - new code bugs:

   - vsock/virtio: suppress used length validation

   - neigh: fix crash in v6 module initialization error path

  Previous releases - regressions:

   - af_unix: fix change in behavior in read after shutdown

   - igb: fix netpoll exit with traffic, avoid warning

   - tls: fix splice_read() when starting mid-record

   - lan743x: fix deadlock in lan743x_phy_link_status_change()

   - marvell: prestera: fix bridge port operation

  Previous releases - always broken:

   - tcp_cubic: fix spurious Hystart ACK train detections for
     not-cwnd-limited flows

   - nexthop: fix refcount issues when replacing IPv6 groups

   - nexthop: fix null pointer dereference when IPv6 is not enabled

   - phylink: force link down and retrigger resolve on interface change

   - mptcp: fix delack timer length calculation and incorrect early
     clearing

   - ieee802154: handle iftypes as u32, prevent shift-out-of-bounds

   - nfc: virtual_ncidev: change default device permissions

   - netfilter: ctnetlink: fix error codes and flags used for kernel
     side filtering of dumps

   - netfilter: flowtable: fix IPv6 tunnel addr match

   - ncsi: align payload to 32-bit to fix dropped packets

   - iavf: fix deadlock and loss of config during VF interface reset

   - ice: avoid bpf_prog refcount underflow

   - ocelot: fix broken PTP over IP and PTP API violations

  Misc:

   - marvell: mvpp2: increase MTU limit when XDP enabled"

* tag 'net-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
  net: dsa: microchip: implement multi-bridge support
  net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
  net: mscc: ocelot: set up traps for PTP packets
  net: ptp: add a definition for the UDP port for IEEE 1588 general messages
  net: mscc: ocelot: create a function that replaces an existing VCAP filter
  net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
  net: hns3: fix incorrect components info of ethtool --reset command
  net: hns3: fix one incorrect value of page pool info when queried by debugfs
  net: hns3: add check NULL address for page pool
  net: hns3: fix VF RSS failed problem after PF enable multi-TCs
  net: qed: fix the array may be out of bound
  net/smc: Don't call clcsock shutdown twice when smc shutdown
  net: vlan: fix underflow for the real_dev refcnt
  ptp: fix filter names in the documentation
  ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
  nfc: virtual_ncidev: change default device permissions
  net/sched: sch_ets: don't peek at classes beyond 'nbands'
  net: stmmac: Disable Tx queues when reconfiguring the interface
  selftests: tls: test for correct proto_ops
  tls: fix replacing proto_ops
  ...

Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:

	ip l a name br0 type bridge
	ip l a name br1 type bridge
	ip l s dev br0 up
	ip l s dev br1 up
	ip l s lan1 master br0
	ip l s dev lan1 up
	ip l s lan2 master br1
	ip l s dev lan2 up

	Ping on lan1 and get response on lan2, which should not happen.

This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.

This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.

Note: STP support was broken before this patch and should be fixed
separately.

Fixes: c2e86691 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>