- 15 May, 2021 9 commits
-
-
José Roberto de Souza authored
When DP_PHY_MODE_STATUS_NOT_SAFE is set, it means that display has the control over the TC phy. The "not safe" naming is confusing using ownership make it easier to read also future platforms will have a new register that does the same job as DP_PHY_MODE_STATUS_NOT_SAFE but with the onwership name. BSpec: 49294 Cc: Imre Deak <imre.deak@intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Signed-off-by:
Clinton Taylor <Clinton.A.Taylor@intel.com> Signed-off-by:
Matt Roper <matthew.d.roper@intel.com> Reviewed-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-10-matthew.d.roper@intel.com
-
Anusha Srivatsa authored
ADL-P has 3 possible refclk frequencies: 19.2MHz, 24MHz and 38.4MHz While we're at it, remove the drm_WARNs. They've never actually helped us catch any problems, but it's very easy to forget to update them properly for new platforms. BSpec: 55409, 49208 Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by:
Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-9-matthew.d.roper@intel.com
-
Matt Roper authored
ADL-P further extends the bits in PLANE_WM that represent blocks and lines; we need to extend our masks accordingly. Since these bits are reserved and MBZ on earlier platforms, it's safe to use the larger bitmask on all platforms. Bspec: 50419 Cc: Matt Atwood <matthew.s.atwood@intel.com> Signed-off-by:
-
José Roberto de Souza authored
This will allow proper DDI initialization based on vbt information. Cc: Uma Shankar <uma.shankar@intel.com> Signed-off-by:
-
Vandita Kulkarni authored
We need slice height to calculate few RC parameters hence assign slice height first. Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Vandita Kulkarni <vandita.kulkarni@intel.com> Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-6-matthew.d.roper@intel.com
-
Vandita Kulkarni authored
Support compression BPPs from bpc to uncompressed BPP -1. So far we have 8,10,12 as valid compressed BPPS now the support is extended. Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Vandita Kulkarni authored
Move the platform specific max bpc calculation into intel_dp_dsc_compute_bpp function Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Matt Roper authored
XE_LPD continues to use the same "skylake-style" watermark programming as other recent platforms. The only change to the watermark calculations compared to Display12 is that XE_LPD now allows a maximum of 255 lines vs the old limit of 31. Due to the larger possible lines value, the corresponding bits representing the value in PLANE_WM are also extended, so make sure we read/write enough bits. Let's also take this opportunity to switch over to the REG_FIELD notation. Bspec: 49325 Bspec: 50419 Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by:
-
Matt Roper authored
The DDI naming template for display version 12 went A-C, TC1-TC6. With XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4. The XE_LPD design keeps the register offsets and bitfields relating to the TC outputs in the same location they were previously. The new "D" and "E" outputs now take the locations that were previously used by TC5 and TC6 outputs, or what we would have considered to be outputs "H" and "I" under the legacy lettering scheme. For the most part everything will just work as long as we initialize the output with the proper 'enum port' value. However we do need to take care to pick the correct AUX channel when parsing the VBT (e.g., a reference to 'AUX D' is actually asking us to use the 8th aux channel, not the fourth). We should also make sure that our encoders and aux channels are named appropriately so that it's easier to correlate driver debug messages with the bspec instructions. v2: - Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose) v3: - Add hpd_pin to handle outputs D and E (Jose) - Fixed conversion of BIOS port to aux ch for TC ports (Jose) Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
- 12 May, 2021 8 commits
-
-
Umesh Nerlige Ramappa authored
Enable relevant OA formats for ADL_P. Cc: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by:
Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Signed-off-by:
Ashutosh Dixit <ashutosh.dixit@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-8-matthew.d.roper@intel.com
-
Clinton Taylor authored
Add ADP-P PCH device ID and assign as ADL PCH if found. Previously we would assign the DDC pin map based on the PCH, but it can also change based on the CPU. From Bspec 20124: "The physical port to pin pair mapping are defined in the Bspec per PCH. Mapping can further change based on CPU Si used as CPU and PCH can be mixed and matched". Bspec: 20124 Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Matt Roper authored
Cc: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by:
-
Matt Roper authored
If VT-d is active, the memory bandwidth usage of the display is 5% higher. Take this into account when determining whether we can support a display configuration. Bspec: 64631 Cc: Matt Atwood <matthew.s.atwood@intel.com> Signed-off-by:
-
Matt Roper authored
Aside from the hardware-managed PG0, XE_LPD has power wells 1-2 and A-D. These power wells should be enabled/disabled according to the following dependency tree (enable top to bottom, disable bottom to top): PG0 | --PG1-- / \ PGA --PG2-- / | \ PGB PGC PGD PWR_WELL_CTL follows the general ICL/TGL design and places PG A-D in the bits that would have been PG 6-9 under the old scheme. PWR_WELL_CTL_{DDI,AUX}'s bit indexing for DDI's A-C and TC1 is the same as TGL, but DDI-D is placed at index 7 (bits 14 & 15). v2: - Squash in LPSP status patch from Uma since it's also a powerwell-specific change. Bspec: 49233 Bspec: 49503 Bspec: 49504 Bspec: 49505 Bspec: 49296 Bspec: 50090 Bspec: 53920 Cc: Anshuman Gupta <anshuman.gupta@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by:Uma Shankar <uma.shankar@intel.com> Reviewed-by:
Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-4-matthew.d.roper@intel.com
-
Matt Roper authored
XE_LPD's plane support is identical to RKL and ADL-S --- 5 universal + 1 cursor with NV12 UV support on planes 1-3 and NV12 Y support on planes 4-5. v2: - Drop the extra 90/270 rotation check in skl_plane_check_fb(); the DRM property code will already prevent userspace from passing us values that weren't advertised. (Lucas) Bspec: 53657 Bspec: 49251 Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
Matt Roper authored
XE_LPD has new AUX interrupt bits for DDI-D and DDI-E that take the spots that were used by TC5/TC6 on Display12 platforms. While we're at it, let's convert the bit definitions for all TGL+ aux bits over to the modern REG_BIT() notation. v2: - Maintain bit order rather than logical order. (Lucas) - Convert surrounding code to REG_BIT() notation. (Lucas) Bspec: 50064 Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
Ankit Nautiyal authored
Fix the typo in DPCD caps used for checking SRC CTL mode of HDMI2.1 PCON v2: Corrected Fixes tag (Jani Nikula). v3: Rebased. Fixes: 04b6603d ("drm/i915/display: Configure HDMI2.1 Pcon for FRL only if Src-Ctl mode is available") Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: "Ville Syrj_l_" <ville.syrjala@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Sean Paul <seanpaul@chromium.org> Signed-off-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by:
Swati Sharma <swati2.sharma@intel.com> Signed-off-by:
Anshuman Gupta <anshuman.gupta@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210511120930.12218-1-ankit.k.nautiyal@intel.com
-
- 11 May, 2021 8 commits
-
-
José Roberto de Souza authored
This workaround requires that VIDEO_DIP_ENABLE_VSC_HSW is never set with PSR. BSpec: 54369 BSpec: 54077 Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
Radhakrishna Sripada <radhakrishna.sripada@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-5-jose.souza@intel.com
-
José Roberto de Souza authored
HSW_TVIDEO_DIP_CTL is read but not used. Signed-off-by:
-
José Roberto de Souza authored
No functional changes in here. Cc: Matt Atwood <matthew.s.atwood@intel.com> Signed-off-by:
-
José Roberto de Souza authored
All of this places don't need to intel_psr_enabled() that will lock psr mutex, check state and unlock. Instead it can directly check PSR state in intel_crtc_state, the only place that was not possible was intel_read_dp_vsc_sdp() but since "drm/i915/display: Fill PSR state during hardware configuration read out" it is possible. Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
José Roberto de Souza authored
So far if we had a mismatch between the state asked and what was programmed in hardware for PSR, this mismatch would go unnoticed. So here adding the PSR to the hardware configuration readout, EDP_PSR_CTL and EDP_PSR2_CTL can't be directly read because its state flips due to other factors like frontbuffer modifications and CRC. Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
Werner Sembach authored
When encoder validation of a display mode fails, retry with less bandwidth heavy YCbCr420 color mode, if available. This enables some HDMI 1.4 setups to support 4k60Hz output, which previously failed silently. AMDGPU had nearly the exact same issue. This problem description is therefore copied from my commit message of the AMDGPU patch. On some setups, while the monitor and the gpu support display modes with pixel clocks of up to 600MHz, the link encoder might not. This prevents YCbCr444 and RGB encoding for 4k60Hz, but YCbCr420 encoding might still be possible. However, which color mode is used is decided before the link encoder capabilities are checked. This patch fixes the problem by retrying to find a display mode with YCbCr420 enforced and using it, if it is valid. Signed-off-by:
Werner Sembach <wse@tuxedocomputers.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210510133349.14491-4-wse@tuxedocomputers.com
-
Werner Sembach authored
Couples the decission between RGB and YCbCr420 mode and the check if the port clock can archive the required frequency. Other checks and configuration steps that where previously done in between can also be done before or after. This allows for are cleaner implementation of retrying different color encodings. A slight change in behaviour occurs with this patch: If YCbCr420 is not allowed but display is YCbCr420 only it no longer fails, but just prints an error and tries to fallback on RGB. Signed-off-by:
-
Werner Sembach authored
Moves some checks that later will be performed 2 times to an own function. This avoids duplicate code later on. Signed-off-by:
-
- 10 May, 2021 4 commits
-
-
Lucas De Marchi authored
Instead of poluting the normal code path in intel_display.c, make intel_bios.c handle the brokenness of the VBT. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210430223808.1078010-5-lucas.demarchi@intel.com
-
Lucas De Marchi authored
Direction on gen9+ was to stop reading the straps and only rely on the VBT for marking the port presence. This happened while dealing with WaIgnoreDDIAStrap and instead of using it as a WA, it should now be the normal flow. See commit 885d3e5b ("drm/i915/display: fix comment on skl straps"). For gen 10 it's hard to say if this will work or not since I can't test it, so leave it with the same behavior as before. For PCH_TGP we should still rely on the VBT to make ports E and F not available. v2 (Ville): - use display ver >= 9 to make it consistent with the rest of the driver instead of checking for == 9 - also handle CNL and only initialize port F if it is IS_CNL_WITH_PORT_F. Eventually CNL may be removed, but while it isn't let's keep it consistent everywhere Signed-off-by:
-
Lucas De Marchi authored
Direction on gen >= 9 was to stop using straps and rely on VBT indicating if the port is present or not. Remove FIXME comment since this will never be "fixed". Signed-off-by:
-
Lucas De Marchi authored
Since commit 45c0673a ("drm/i915/bios: start using the intel_bios_encoder_data directly") we lookup the devdata for each port in intel_ddi_init() and just return if the port is not present in VBT (or if we didn't create a fake devdata for it if VBT is not available). So in intel_display.c we don't have to check intel_bios_is_port_present(), just rely on the check in intel_ddi_init(). v2: Rebase on commit 45c0673a ("drm/i915/bios: start using the intel_bios_encoder_data directly") re-using that check in intel_ddi_init() instead of adding a new one. Signed-off-by:
-
- 07 May, 2021 11 commits
-
-
Imre Deak authored
Enable padding of DPT FB strides to POT, using the FB remapping logic. Signed-off-by:
-
Imre Deak authored
The specification only requires DPT FB strides to be POT aligned, but there seems to be also a minimum of 8 stride tile requirement. Scanning out FBs with < 8 stride tiles will result in pipe faults (even though the stride is POT aligned). Signed-off-by:
-
Imre Deak authored
The latest specification removed the support for 90/270 FB rotation on ADL_P, even though legacy Y-tiled surfaces are supported. Align the code accordingly. Signed-off-by:
-
José Roberto de Souza authored
Alderlake-P have a new stride restriction when using DPT and it is used by non linear framebuffers. Stride needs to be a power of two to take full DPT rows, but stride is a parameter set by userspace. What we could do is use a fake stride when doing DPT allocation so HW requirements are met and userspace don't need to be changed to met this power of two restrictions but this change will take a while to be implemented so for now adding this restriction in driver to reject atomic commits that would cause visual corruptions. BSpec: 53393 Acked-by:
-
Juha-Pekka Heikkilä authored
XE_LPD supports plane strides up to 128KB. Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Signed-off-by:
Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com> Signed-off-by:
-
José Roberto de Souza authored
GTT remapping allow us to have planes with strides larger than HW supports but DPT + GTT remapping is still not properly handled so falling back to plane HW limitations for now. This patch can be dropped when DPT + GTT remapping is correctly handled but until then we need this limitation for all display13 platforms to avoid pipe faults. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Clint Taylor <Clinton.A.Taylor@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Suggested-by:
-
Ville Syrjälä authored
Add support for DPT (display page table). DPT is a slightly peculiar two level page table scheme used for tiled scanout buffers (linear uses direct ggtt mapping still). The plane surface address will point at a page in the DPT which holds the PTEs for 512 actual pages. Thus we require 1/512 of the ggttt address space compared to a direct ggtt mapping. We create a new DPT address space for each framebuffer and track two vmas (one for the DPT, another for the ggtt). TODO: - Is the i915_address_space approaach sane? - Maybe don't map the whole DPT to write the PTEs? - Deal with remapping/rotation? Need to create a separate DPT for each remapped/rotated plane I guess. Or else we'd need to make the per-fb DPT large enough to support potentially several remapped/rotated vmas. How large should that be? Signed-off-by:
Bommu Krishnaiah <krishnaiah.bommu@intel.com> Cc: Wilson Chris P <Chris.P.Wilson@intel.com> Cc: Tang CQ <cq.tang@intel.com> Cc: Auld Matthew <matthew.auld@intel.com> Reviewed-by:
Wilson Chris P <Chris.P.Wilson@intel.com> Signed-off-by:
-
Clinton Taylor authored
Add ADL-P to the device_info table and support MACROS. Bspec: 49185, 55372, 55373 Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Clinton Taylor authored
Add 18 known PCI device IDs Bspec: 55376 Cc: Caz Yokoyama <caz.yokoyama@intel.com> Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Matt Roper authored
Let's start preparing for upcoming platforms that will use an XE_LPD design. v2: - Use the now-preferred "XE_LPD" term to refer to this design - Utilize DISPLAY_VER() rather than a feature flag - Drop unused mbus_size field (Lucas) v3: - Adjust for dbuf.{size,slice_mask} (Ville) Signed-off-by: -
Ville Syrjälä authored
When scanning out NV12 if we at any time have the plane enabled while the scaler is disabled we get a pretty catastrophic underrun. Let's reorder the operations so that we try to avoid that happening even if our vblank evade fails and the scaler enable/disable and the plane enable/disable get latched during two diffent frames. This takes care of the most common cases. I suppose there is still at least a theoretical possibility of hitting this if one plane takes the scaler away from another plane before the second plane had a chance to set up another scaler for its use. But that is starting to get a bit complicated, especially since the plane commit order already has to be carefully sequenced to avoid any dbuf overlaps. So plugging this 100% may prove somewhat hard... Cc: Cooper Chiou <cooper.chiou@intel.com> Signed-off-by:
Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
-
