- 08 Sep, 2022 8 commits
-
-
Sylwester Dziedziuch authored
Previously changing mac address gives false negative because ip link set <interface> address <MAC> return with RTNLINK: Permission denied. In iavf_set_mac was check if PF handled our mac set request, even before filter was added to list. Because this check returns always true and it never waits for PF's response. Move iavf_is_mac_handled to wait_event_interruptible_timeout instead of false. Now it will wait for PF's response and then check if address was added or rejected. Fixes: 35a2443d ("iavf: Add waiting for response from PF in set mac") Signed-off-by:
Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Co-developed-by:
Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by:
Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by:
Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Ding Hui authored
There are problems if allocated queues less than Traffic Classes. Commit a632b2a4 ("ice: ethtool: Prohibit improper channel config for DCB") already disallow setting less queues than TCs. Another case is if we first set less queues, and later update more TCs config due to LLDP, ice_vsi_cfg_tc() will failed but left dirty num_txq/rxq and tc_cfg in vsi, that will cause invalid pointer access. [ 95.968089] ice 0000:3b:00.1: More TCs defined than queues/rings allocated. [ 95.968092] ice 0000:3b:00.1: Trying to use more Rx queues (8), than were allocated (1)! [ 95.968093] ice 0000:3b:00.1: Failed to config TC for VSI index: 0 [ 95.969621] general protection fault: 0000 [#1] SMP NOPTI [ 95.969705] CPU: 1 PID: 58405 Comm: lldpad Kdump: loaded Tainted: G U W O --------- -t - 4.18.0 #1 [ 95.969867] Hardware name: O.E.M/BC11SPSCB10, BIOS 8.23 12/30/2021 [ 95.969992] RIP: 0010:devm_kmalloc+0xa/0x60 [ 95.970052] Code: 5c ff ff ff 31 c0 5b 5d 41 5c c3 b8 f4 ff ff ff eb f4 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 89 d1 <8b> 97 60 02 00 00 48 8d 7e 18 48 39 f7 72 3f 55 89 ce 53 48 8b 4c [ 95.970344] RSP: 0018:ffffc9003f553888 EFLAGS: 00010206 [ 95.970425] RAX: dead000000000200 RBX: ffffea003c425b00 RCX: 00000000006080c0 [ 95.970536] RDX: 00000000006080c0 RSI: 0000000000000200 RDI: dead000000000200 [ 95.970648] RBP: dead000000000200 R08: 00000000000463c0 R09: ffff888ffa900000 [ 95.970760] R10: 0000000000000000 R11: 0000000000000002 R12: ffff888ff6b40100 [ 95.970870] R13: ffff888ff6a55018 R14: 0000000000000000 R15: ffff888ff6a55460 [ 95.970981] FS: 00007f51b7d24700(0000) GS:ffff88903ee80000(0000) knlGS:0000000000000000 [ 95.971108] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 95.971197] CR2: 00007fac5410d710 CR3: 0000000f2c1de002 CR4: 00000000007606e0 [ 95.971309] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 95.971419] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 95.971530] PKRU: 55555554 [ 95.971573] Call Trace: [ 95.971622] ice_setup_rx_ring+0x39/0x110 [ice] [ 95.971695] ice_vsi_setup_rx_rings+0x54/0x90 [ice] [ 95.971774] ice_vsi_open+0x25/0x120 [ice] [ 95.971843] ice_open_internal+0xb8/0x1f0 [ice] [ 95.971919] ice_ena_vsi+0x4f/0xd0 [ice] [ 95.971987] ice_dcb_ena_dis_vsi.constprop.5+0x29/0x90 [ice] [ 95.972082] ice_pf_dcb_cfg+0x29a/0x380 [ice] [ 95.972154] ice_dcbnl_setets+0x174/0x1b0 [ice] [ 95.972220] dcbnl_ieee_set+0x89/0x230 [ 95.972279] ? dcbnl_ieee_del+0x150/0x150 [ 95.972341] dcb_doit+0x124/0x1b0 [ 95.972392] rtnetlink_rcv_msg+0x243/0x2f0 [ 95.972457] ? dcb_doit+0x14d/0x1b0 [ 95.972510] ? __kmalloc_node_track_caller+0x1d3/0x280 [ 95.972591] ? rtnl_calcit.isra.31+0x100/0x100 [ 95.972661] netlink_rcv_skb+0xcf/0xf0 [ 95.972720] netlink_unicast+0x16d/0x220 [ 95.972781] netlink_sendmsg+0x2ba/0x3a0 [ 95.975891] sock_sendmsg+0x4c/0x50 [ 95.979032] ___sys_sendmsg+0x2e4/0x300 [ 95.982147] ? kmem_cache_alloc+0x13e/0x190 [ 95.985242] ? __wake_up_common_lock+0x79/0x90 [ 95.988338] ? __check_object_size+0xac/0x1b0 [ 95.991440] ? _copy_to_user+0x22/0x30 [ 95.994539] ? move_addr_to_user+0xbb/0xd0 [ 95.997619] ? __sys_sendmsg+0x53/0x80 [ 96.000664] __sys_sendmsg+0x53/0x80 [ 96.003747] do_syscall_64+0x5b/0x1d0 [ 96.006862] entry_SYSCALL_64_after_hwframe+0x65/0xca Only update num_txq/rxq when passed check, and restore tc_cfg if setup queue map failed. Fixes: a632b2a4 ("ice: ethtool: Prohibit improper channel config for DCB") Signed-off-by:
Ding Hui <dinghui@sangfor.com.cn> Reviewed-by:
Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by:
-
Dave Ertman authored
In the IDC callback that is accessed when the aux drivers request a reset, the function to unplug the aux devices is called. This function is also called in the ice_prepare_for_reset function. This double call is causing a "scheduling while atomic" BUG. [ 662.676430] ice 0000:4c:00.0 rocep76s0: cqp opcode = 0x1 maj_err_code = 0xffff min_err_code = 0x8003 [ 662.676609] ice 0000:4c:00.0 rocep76s0: [Modify QP Cmd Error][op_code=8] status=-29 waiting=1 completion_err=1 maj=0xffff min=0x8003 [ 662.815006] ice 0000:4c:00.0 rocep76s0: ICE OICR event notification: oicr = 0x10000003 [ 662.815014] ice 0000:4c:00.0 rocep76s0: critical PE Error, GLPE_CRITERR=0x00011424 [ 662.815017] ice 0000:4c:00.0 rocep76s0: Requesting a reset [ 662.815475] BUG: scheduling while atomic: swapper/37/0/0x00010002 [ 662.815475] BUG: scheduling while atomic: swapper/37/0/0x00010002 [ 662.815477] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs rfkill 8021q garp mrp stp llc vfat fat rpcrdma intel_rapl_msr intel_rapl_common sunrpc i10nm_edac rdma_ucm nfit ib_srpt libnvdimm ib_isert iscsi_target_mod x86_pkg_temp_thermal intel_powerclamp coretemp target_core_mod snd_hda_intel ib_iser snd_intel_dspcfg libiscsi snd_intel_sdw_acpi scsi_transport_iscsi kvm_intel iTCO_wdt rdma_cm snd_hda_codec kvm iw_cm ipmi_ssif iTCO_vendor_support snd_hda_core irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hwdep snd_seq snd_seq_device rapl snd_pcm snd_timer isst_if_mbox_pci pcspkr isst_if_mmio irdma intel_uncore idxd acpi_ipmi joydev isst_if_common snd mei_me idxd_bus ipmi_si soundcore i2c_i801 mei ipmi_devintf i2c_smbus i2c_ismt ipmi_msghandler acpi_power_meter acpi_pad rv(OE) ib_uverbs ib_cm ib_core xfs libcrc32c ast i2c_algo_bit drm_vram_helper drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm_ttm_helpe r ttm [ 662.815546] nvme nvme_core ice drm crc32c_intel i40e t10_pi wmi pinctrl_emmitsburg dm_mirror dm_region_hash dm_log dm_mod fuse [ 662.815557] Preemption disabled at: [ 662.815558] [<0000000000000000>] 0x0 [ 662.815563] CPU: 37 PID: 0 Comm: swapper/37 Kdump: loaded Tainted: G S OE 5.17.1 #2 [ 662.815566] Hardware name: Intel Corporation D50DNP/D50DNP, BIOS SE5C6301.86B.6624.D18.2111021741 11/02/2021 [ 662.815568] Call Trace: [ 662.815572] <IRQ> [ 662.815574] dump_stack_lvl+0x33/0x42 [ 662.815581] __schedule_bug.cold.147+0x7d/0x8a [ 662.815588] __schedule+0x798/0x990 [ 662.815595] schedule+0x44/0xc0 [ 662.815597] schedule_preempt_disabled+0x14/0x20 [ 662.815600] __mutex_lock.isra.11+0x46c/0x490 [ 662.815603] ? __ibdev_printk+0x76/0xc0 [ib_core] [ 662.815633] device_del+0x37/0x3d0 [ 662.815639] ice_unplug_aux_dev+0x1a/0x40 [ice] [ 662.815674] ice_schedule_reset+0x3c/0xd0 [ice] [ 662.815693] irdma_iidc_event_handler.cold.7+0xb6/0xd3 [irdma] [ 662.815712] ? bitmap_find_next_zero_area_off+0x45/0xa0 [ 662.815719] ice_send_event_to_aux+0x54/0x70 [ice] [ 662.815741] ice_misc_intr+0x21d/0x2d0 [ice] [ 662.815756] __handle_irq_event_percpu+0x4c/0x180 [ 662.815762] handle_irq_event_percpu+0xf/0x40 [ 662.815764] handle_irq_event+0x34/0x60 [ 662.815766] handle_edge_irq+0x9a/0x1c0 [ 662.815770] __common_interrupt+0x62/0x100 [ 662.815774] common_interrupt+0xb4/0xd0 [ 662.815779] </IRQ> [ 662.815780] <TASK> [ 662.815780] asm_common_interrupt+0x1e/0x40 [ 662.815785] RIP: 0010:cpuidle_enter_state+0xd6/0x380 [ 662.815789] Code: 49 89 c4 0f 1f 44 00 00 31 ff e8 65 d7 95 ff 45 84 ff 74 12 9c 58 f6 c4 02 0f 85 64 02 00 00 31 ff e8 ae c5 9c ff fb 45 85 f6 <0f> 88 12 01 00 00 49 63 d6 4c 2b 24 24 48 8d 04 52 48 8d 04 82 49 [ 662.815791] RSP: 0018:ff2c2c4f18edbe80 EFLAGS: 00000202 [ 662.815793] RAX: ff280805df140000 RBX: 0000000000000002 RCX: 000000000000001f [ 662.815795] RDX: 0000009a52da2d08 RSI: ffffffff93f8240b RDI: ffffffff93f53ee7 [ 662.815796] RBP: ff5e2bd11ff41928 R08: 0000000000000000 R09: 000000000002f8c0 [ 662.815797] R10: 0000010c3f18e2cf R11: 000000000000000f R12: 0000009a52da2d08 [ 662.815798] R13: ffffffff94ad7e20 R14: 0000000000000002 R15: 0000000000000000 [ 662.815801] cpuidle_enter+0x29/0x40 [ 662.815803] do_idle+0x261/0x2b0 [ 662.815807] cpu_startup_entry+0x19/0x20 [ 662.815809] start_secondary+0x114/0x150 [ 662.815813] secondary_startup_64_no_verify+0xd5/0xdb [ 662.815818] </TASK> [ 662.815846] bad: scheduling from the idle thread! [ 662.815849] CPU: 37 PID: 0 Comm: swapper/37 Kdump: loaded Tainted: G S W OE 5.17.1 #2 [ 662.815852] Hardware name: Intel Corporation D50DNP/D50DNP, BIOS SE5C6301.86B.6624.D18.2111021741 11/02/2021 [ 662.815853] Call Trace: [ 662.815855] <IRQ> [ 662.815856] dump_stack_lvl+0x33/0x42 [ 662.815860] dequeue_task_idle+0x20/0x30 [ 662.815863] __schedule+0x1c3/0x990 [ 662.815868] schedule+0x44/0xc0 [ 662.815871] schedule_preempt_disabled+0x14/0x20 [ 662.815873] __mutex_lock.isra.11+0x3a8/0x490 [ 662.815876] ? __ibdev_printk+0x76/0xc0 [ib_core] [ 662.815904] device_del+0x37/0x3d0 [ 662.815909] ice_unplug_aux_dev+0x1a/0x40 [ice] [ 662.815937] ice_schedule_reset+0x3c/0xd0 [ice] [ 662.815961] irdma_iidc_event_handler.cold.7+0xb6/0xd3 [irdma] [ 662.815979] ? bitmap_find_next_zero_area_off+0x45/0xa0 [ 662.815985] ice_send_event_to_aux+0x54/0x70 [ice] [ 662.816011] ice_misc_intr+0x21d/0x2d0 [ice] [ 662.816033] __handle_irq_event_percpu+0x4c/0x180 [ 662.816037] handle_irq_event_percpu+0xf/0x40 [ 662.816039] handle_irq_event+0x34/0x60 [ 662.816042] handle_edge_irq+0x9a/0x1c0 [ 662.816045] __common_interrupt+0x62/0x100 [ 662.816048] common_interrupt+0xb4/0xd0 [ 662.816052] </IRQ> [ 662.816053] <TASK> [ 662.816054] asm_common_interrupt+0x1e/0x40 [ 662.816057] RIP: 0010:cpuidle_enter_state+0xd6/0x380 [ 662.816060] Code: 49 89 c4 0f 1f 44 00 00 31 ff e8 65 d7 95 ff 45 84 ff 74 12 9c 58 f6 c4 02 0f 85 64 02 00 00 31 ff e8 ae c5 9c ff fb 45 85 f6 <0f> 88 12 01 00 00 49 63 d6 4c 2b 24 24 48 8d 04 52 48 8d 04 82 49 [ 662.816063] RSP: 0018:ff2c2c4f18edbe80 EFLAGS: 00000202 [ 662.816065] RAX: ff280805df140000 RBX: 0000000000000002 RCX: 000000000000001f [ 662.816067] RDX: 0000009a52da2d08 RSI: ffffffff93f8240b RDI: ffffffff93f53ee7 [ 662.816068] RBP: ff5e2bd11ff41928 R08: 0000000000000000 R09: 000000000002f8c0 [ 662.816070] R10: 0000010c3f18e2cf R11: 000000000000000f R12: 0000009a52da2d08 [ 662.816071] R13: ffffffff94ad7e20 R14: 0000000000000002 R15: 0000000000000000 [ 662.816075] cpuidle_enter+0x29/0x40 [ 662.816077] do_idle+0x261/0x2b0 [ 662.816080] cpu_startup_entry+0x19/0x20 [ 662.816083] start_secondary+0x114/0x150 [ 662.816087] secondary_startup_64_no_verify+0xd5/0xdb [ 662.816091] </TASK> [ 662.816169] bad: scheduling from the idle thread! The correct place to unplug the aux devices for a reset is in the prepare_for_reset function, as this is a common place for all reset flows. It also has built in protection from being called twice in a single reset instance before the aux devices are replugged. Fixes: f9f5301e ("ice: Register auxiliary device to provide RDMA") Signed-off-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by:
Helena Anna Dubel <helena.anna.dubel@intel.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from rxrpc, netfilter, wireless and bluetooth subtrees. Current release - regressions: - skb: export skb drop reaons to user by TRACE_DEFINE_ENUM - bluetooth: fix regression preventing ACL packet transmission Current release - new code bugs: - dsa: microchip: fix kernel oops on ksz8 switches - dsa: qca8k: fix NULL pointer dereference for of_device_get_match_data Previous releases - regressions: - netfilter: clean up hook list when offload flags check fails - wifi: mt76: fix crash in chip reset fail - rxrpc: fix ICMP/ICMP6 error handling - ice: fix DMA mappings leak - i40e: fix kernel crash during module removal Previous releases - always broken: - ipv6: sr: fix out-of-bounds read when setting HMAC data. - tcp: TX zerocopy should not sense pfmemalloc status - sch_sfb: don't assume the skb is still around after enqueueing to child - netfilter: drop dst references before setting - wifi: wilc1000: fix DMA on stack objects - rxrpc: fix an insufficiently large sglist in rxkad_verify_packet_2() - fec: use a spinlock to guard `fep->ptp_clk_on` Misc: - usb: qmi_wwan: add Quectel RM520N" * tag 'net-6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits) sch_sfb: Also store skb len before calling child enqueue net: phy: lan87xx: change interrupt src of link_up to comm_ready net/smc: Fix possible access to freed memory in link clear net: ethernet: mtk_eth_soc: check max allowed hash in mtk_ppe_check_skb net: skb: export skb drop reaons to user by TRACE_DEFINE_ENUM net: ethernet: mtk_eth_soc: fix typo in __mtk_foe_entry_clear net: dsa: felix: access QSYS_TAG_CONFIG under tas_lock in vsc9959_sched_speed_set net: dsa: felix: disable cut-through forwarding for frames oversized for tc-taprio net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet net: usb: qmi_wwan: add Quectel RM520N net: dsa: qca8k: fix NULL pointer dereference for of_device_get_match_data tcp: fix early ETIMEDOUT after spurious non-SACK RTO stmmac: intel: Simplify intel_eth_pci_remove() net: mvpp2: debugfs: fix memory leak when using debugfs_lookup() ipv6: sr: fix out-of-bounds read when setting HMAC data. bonding: accept unsolicited NA message bonding: add all node mcast address when slave up bonding: use unspecified address if no available link local address wifi: use struct_group to copy addresses wifi: mac80211_hwsim: check length for virtio packets ... -
Linus Torvalds authored
Commit d4252071 ("add barriers to buffer_uptodate and set_buffer_uptodate") added proper memory barriers to the buffer head BH_Uptodate bit, so that anybody who tests a buffer for being up-to-date will be guaranteed to actually see initialized state. However, that commit didn't _just_ add the memory barrier, it also ended up dropping the "was it already set" logic that the BUFFER_FNS() macro had. That's conceptually the right thing for a generic "this is a memory barrier" operation, but in the case of the buffer contents, we really only care about the memory barrier for the _first_ time we set the bit, in that the only memory ordering protection we need is to avoid anybody seeing uninitialized memory contents. Any other access ordering wouldn't be about the BH_Uptodate bit anyway, and would require some other proper lock (typically BH_Lock or the folio lock). A reader that races with somebody invalidating the buffer head isn't an issue wrt the memory ordering, it's a serialization issue. Now, you'd think that the buffer head operations don't matter in this day and age (and I certainly thought so), but apparently some loads still end up being heavy users of buffer heads. In particular, the kernel test robot reported that not having this bit access optimization in place caused a noticeable direct IO performance regression on ext4: fxmark.ssd_ext4_no_jnl_DWTL_54_directio.works/sec -26.5% regression although you presumably need a fast disk and a lot of cores to actually notice. Link: https://lore.kernel.org/all/Yw8L7HTZ%2FdE2%2Fo9C@xsang-OptiPlex-9020/Reported-by:
kernel test robot <oliver.sang@intel.com> Tested-by:
Fengwei Yin <fengwei.yin@intel.com> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: stable@kernel.org Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efiLinus Torvalds authored
Pull EFI fixes from Ard Biesheuvel: "A couple of low-priority EFI fixes: - prevent the randstruct plugin from re-ordering EFI protocol definitions - fix a use-after-free in the capsule loader - drop unused variable" * tag 'efi-urgent-for-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: efi: capsule-loader: Fix use-after-free in efi_capsule_write efi/x86: libstub: remove unused variable efi: libstub: Disable struct randomization -
Toke Høiland-Jørgensen authored
Cong Wang noticed that the previous fix for sch_sfb accessing the queued skb after enqueueing it to a child qdisc was incomplete: the SFB enqueue function was also calling qdisc_qstats_backlog_inc() after enqueue, which reads the pkt len from the skb cb field. Fix this by also storing the skb len, and using the stored value to increment the backlog after enqueueing. Fixes: 9efd2329 ("sch_sfb: Don't assume the skb is still around after enqueueing to child") Signed-off-by:
Toke Høiland-Jørgensen <toke@toke.dk> Acked-by:
Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20220905192137.965549-1-toke@toke.dkSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Arun Ramadoss authored
Currently phy link up/down interrupt is enabled using the LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function, phy link is determined using the T1_MODE_STAT_REG register comm_ready bit. comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status. Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set first but comm_ready bit takes some time to set based on local and remote receiver status. As per the current implementation, interrupt is triggered using link_up but the comm_ready bit is still cleared in the read_status function. So, link is always down. Initially tested with the shared interrupt mechanism with switch and internal phy which is working, but after implementing interrupt controller it is not working. It can fixed either by updating the read_status function to read from LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for comm_ready bit. But the validation team recommends the use of comm_ready for link detection. This patch fixes by enabling the comm_ready bit for link_up in the LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in LAN87xx_INTERRUPT_MASK register. Fixes: 8a1b415d ("net: phy: added ethtool master-slave configuration support") Signed-off-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220905152750.5079-1-arun.ramadoss@microchip.comSigned-off-by:
-
- 07 Sep, 2022 12 commits
-
-
Hyunwoo Kim authored
A race condition may occur if the user calls close() on another thread during a write() operation on the device node of the efi capsule. This is a race condition that occurs between the efi_capsule_write() and efi_capsule_flush() functions of efi_capsule_fops, which ultimately results in UAF. So, the page freeing process is modified to be done in efi_capsule_release() instead of efi_capsule_flush(). Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by:
Hyunwoo Kim <imv4bel@gmail.com> Link: https://lore.kernel.org/all/20220907102920.GA88602@ubuntu/Signed-off-by:
Ard Biesheuvel <ardb@kernel.org>
-
Yacan Liu authored
After modifying the QP to the Error state, all RX WR would be completed with WC in IB_WC_WR_FLUSH_ERR status. Current implementation does not wait for it is done, but destroy the QP and free the link group directly. So there is a risk that accessing the freed memory in tasklet context. Here is a crash example: BUG: unable to handle page fault for address: ffffffff8f220860 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD f7300e067 P4D f7300e067 PUD f7300f063 PMD 8c4e45063 PTE 800ffff08c9df060 Oops: 0002 [#1] SMP PTI CPU: 1 PID: 0 Comm: swapper/1 Kdump: loaded Tainted: G S OE 5.10.0-0607+ #23 Hardware name: Inspur NF5280M4/YZMB-00689-101, BIOS 4.1.20 07/09/2018 RIP: 0010:native_queued_spin_lock_slowpath+0x176/0x1b0 Code: f3 90 48 8b 32 48 85 f6 74 f6 eb d5 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 05 48 63 f6 48 05 00 c8 02 00 48 03 04 f5 00 09 98 8e <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 32 RSP: 0018:ffffb3b6c001ebd8 EFLAGS: 00010086 RAX: ffffffff8f220860 RBX: 0000000000000246 RCX: 0000000000080000 RDX: ffff91db1f86c800 RSI: 000000000000173c RDI: ffff91db62bace00 RBP: ffff91db62bacc00 R08: 0000000000000000 R09: c00000010000028b R10: 0000000000055198 R11: ffffb3b6c001ea58 R12: ffff91db80e05010 R13: 000000000000000a R14: 0000000000000006 R15: 0000000000000040 FS: 0000000000000000(0000) GS:ffff91db1f840000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffff8f220860 CR3: 00000001f9580004 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> _raw_spin_lock_irqsave+0x30/0x40 mlx5_ib_poll_cq+0x4c/0xc50 [mlx5_ib] smc_wr_rx_tasklet_fn+0x56/0xa0 [smc] tasklet_action_common.isra.21+0x66/0x100 __do_softirq+0xd5/0x29c asm_call_irq_on_stack+0x12/0x20 </IRQ> do_softirq_own_stack+0x37/0x40 irq_exit_rcu+0x9d/0xa0 sysvec_call_function_single+0x34/0x80 asm_sysvec_call_function_single+0x12/0x20 Fixes: bd4ad577 ("smc: initialize IB transport incl. PD, MR, QP, CQ, event, WR") Signed-off-by:
Yacan Liu <liuyacan@corp.netease.com> Reviewed-by:
Tony Lu <tonylu@linux.alibaba.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Lorenzo Bianconi authored
Even if max hash configured in hw in mtk_ppe_hash_entry is MTK_PPE_ENTRIES - 1, check theoretical OOB accesses in mtk_ppe_check_skb routine Fixes: c4f033d9 ("net: ethernet: mtk_eth_soc: rework hardware flow table management") Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Menglong Dong authored
As Eric reported, the 'reason' field is not presented when trace the kfree_skb event by perf: $ perf record -e skb:kfree_skb -a sleep 10 $ perf script ip_defrag 14605 [021] 221.614303: skb:kfree_skb: skbaddr=0xffff9d2851242700 protocol=34525 location=0xffffffffa39346b1 reason: The cause seems to be passing kernel address directly to TP_printk(), which is not right. As the enum 'skb_drop_reason' is not exported to user space through TRACE_DEFINE_ENUM(), perf can't get the drop reason string from the 'reason' field, which is a number. Therefore, we introduce the macro DEFINE_DROP_REASON(), which is used to define the trace enum by TRACE_DEFINE_ENUM(). With the help of DEFINE_DROP_REASON(), now we can remove the auto-generate that we introduced in the commit ec43908d ("net: skb: use auto-generation to convert skb drop reason to string"), and define the string array 'drop_reasons'. Hmmmm...now we come back to the situation that have to maintain drop reasons in both enum skb_drop_reason and DEFINE_DROP_REASON. But they are both in dropreason.h, which makes it easier. After this commit, now the format of kfree_skb is like this: $ cat /tracing/events/skb/kfree_skb/format name: kfree_skb ID: 1524 format: field:unsigned short common_type; offset:0; size:2; signed:0; field:unsigned char common_flags; offset:2; size:1; signed:0; field:unsigned char common_preempt_count; offset:3; size:1; signed:0; field:int common_pid; offset:4; size:4; signed:1; field:void * skbaddr; offset:8; size:8; signed:0; field:void * location; offset:16; size:8; signed:0; field:unsigned short protocol; offset:24; size:2; signed:0; field:enum skb_drop_reason reason; offset:28; size:4; signed:0; print fmt: "skbaddr=%p protocol=%u location=%p reason: %s", REC->skbaddr, REC->protocol, REC->location, __print_symbolic(REC->reason, { 1, "NOT_SPECIFIED" }, { 2, "NO_SOCKET" } ...... Fixes: ec43908d ("net: skb: use auto-generation to convert skb drop reason to string") Link: https://lore.kernel.org/netdev/CANn89i+bx0ybvE55iMYf5GJM48WwV1HNpdm9Q6t-HaEstqpCSA@mail.gmail.com/Reported-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Menglong Dong <imagedong@tencent.com> Signed-off-by:
-
Lorenzo Bianconi authored
Set ib1 state to MTK_FOE_STATE_UNBIND in __mtk_foe_entry_clear routine. Fixes: 33fc42de ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries") Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Fixes for Felix DSA driver calculation of tc-taprio guard bands This series fixes some bugs which are not quite new, but date from v5.13 when static guard bands were enabled by Michael Walle to prevent tc-taprio overruns. The investigation started when Xiaoliang asked privately what is the expected max SDU for a traffic class when its minimum gate interval is 10 us. The answer, as it turns out, is not an L1 size of 1250 octets, but 1245 octets, since otherwise, the switch will not consider frames for egress scheduling, because the static guard band is exactly as large as the time interval. The switch needs a minimum of 33 ns outside of the guard band to consider a frame for scheduling, and the reduction of the max SDU by 5 provides exactly for that. The fix for that (patch 1/3) is relatively small, but during testing, it became apparent that cut-through forwarding prevents oversized frame dropping from working properly. This is solved through the larger patch 2/3. Finally, patch 3/3 fixes one more tc-taprio locking problem found through code inspection. ==================== Signed-off-by: -
Vladimir Oltean authored
The read-modify-write of QSYS_TAG_CONFIG from vsc9959_sched_speed_set() runs unlocked with respect to the other functions that access it, which are vsc9959_tas_guard_bands_update(), vsc9959_qos_port_tas_set() and vsc9959_tas_clock_adjust(). All the others are under ocelot->tas_lock, so move the vsc9959_sched_speed_set() access under that lock as well, to resolve the concurrency. Fixes: 55a515b1 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
Experimentally, it looks like when QSYS_QMAXSDU_CFG_7 is set to 605, frames even way larger than 601 octets are transmitted even though these should be considered as oversized, according to the documentation, and dropped. Since oversized frame dropping depends on frame size, which is only known at the EOF stage, and therefore not at SOF when cut-through forwarding begins, it means that the switch cannot take QSYS_QMAXSDU_CFG_* into consideration for traffic classes that are cut-through. Since cut-through forwarding has no UAPI to control it, and the driver enables it based on the mantra "if we can, then why not", the strategy is to alter vsc9959_cut_through_fwd() to take into consideration which tc's have oversize frame dropping enabled, and disable cut-through for them. Then, from vsc9959_tas_guard_bands_update(), we re-trigger the cut-through determination process. There are 2 strategies for vsc9959_cut_through_fwd() to determine whether a tc has oversized dropping enabled or not. One is to keep a bit mask of traffic classes per port, and the other is to read back from the hardware registers (a non-zero value of QSYS_QMAXSDU_CFG_* means the feature is enabled). We choose reading back from registers, because struct ocelot_port is shared with drivers (ocelot, seville) that don't support either cut-through nor tc-taprio, and we don't have a felix specific extension of struct ocelot_port. Furthermore, reading registers from the Felix hardware is quite cheap, since they are memory-mapped. Fixes: 55a515b1 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by:
-
Vladimir Oltean authored
The blamed commit broke tc-taprio schedules such as this one: tc qdisc replace dev $swp1 root taprio \ num_tc 8 \ map 0 1 2 3 4 5 6 7 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \ base-time 0 \ sched-entry S 0x7f 990000 \ sched-entry S 0x80 10000 \ flags 0x2 because the gate entry for TC 7 (S 0x80 10000 ns) now has a static guard band added earlier than its 'gate close' event, such that packet overruns won't occur in the worst case of the largest packet possible. Since guard bands are statically determined based on the per-tc QSYS_QMAXSDU_CFG_* with a fallback on the port-based QSYS_PORT_MAX_SDU, we need to discuss what happens with TC 7 depending on kernel version, since the driver, prior to commit 55a515b1 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port"), did not touch QSYS_QMAXSDU_CFG_*, and therefore relied on QSYS_PORT_MAX_SDU. 1 (before vsc9959_tas_guard_bands_update): QSYS_PORT_MAX_SDU defaults to 1518, and at gigabit this introduces a static guard band (independent of packet sizes) of 12144 ns, plus QSYS::HSCH_MISC_CFG.FRM_ADJ (bit time of 20 octets => 160 ns). But this is larger than the time window itself, of 10000 ns. So, the queue system never considers a frame with TC 7 as eligible for transmission, since the gate practically never opens, and these frames are forever stuck in the TX queues and hang the port. 2 (after vsc9959_tas_guard_bands_update): Under the sole goal of enabling oversized frame dropping, we make an effort to set QSYS_QMAXSDU_CFG_7 to 1230 bytes. But QSYS_QMAXSDU_CFG_7 plays one more role, which we did not take into account: per-tc static guard band, expressed in L2 byte time (auto-adjusted for FCS and L1 overhead). There is a discrepancy between what the driver thinks (that there is no guard band, and 100% of min_gate_len[tc] is available for egress scheduling) and what the hardware actually does (crops the equivalent of QSYS_QMAXSDU_CFG_7 ns out of min_gate_len[tc]). In practice, this means that the hardware thinks it has exactly 0 ns for scheduling tc 7. In both cases, even minimum sized Ethernet frames are stuck on egress rather than being considered for scheduling on TC 7, even if they would fit given a proper configuration. Considering the current situation, with vsc9959_tas_guard_bands_update(), frames between 60 octets and 1230 octets in size are not eligible for oversized dropping (because they are smaller than QSYS_QMAXSDU_CFG_7), but won't be considered as eligible for scheduling either, because the min_gate_len[7] (10000 ns) minus the guard band determined by QSYS_QMAXSDU_CFG_7 (1230 octets * 8 ns per octet == 9840 ns) minus the guard band auto-added for L1 overhead by QSYS::HSCH_MISC_CFG.FRM_ADJ (20 octets * 8 ns per octet == 160 octets) leaves 0 ns for scheduling in the queue system proper. Investigating the hardware behavior, it becomes apparent that the queue system needs precisely 33 ns of 'gate open' time in order to consider a frame as eligible for scheduling to a tc. So the solution to this problem is to amend vsc9959_tas_guard_bands_update(), by giving the per-tc guard bands less space by exactly 33 ns, just enough for one frame to be scheduled in that interval. This allows the queue system to make forward progress for that port-tc, and prevents it from hanging. Fixes: 297c4de6 ("net: dsa: felix: re-enable TAS guard band mode") Reported-by:Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by:
-
chen zhang authored
The variable "has_system_memory" is unused in function ‘adjust_memory_range_protection’, remove it. Signed-off-by:
chen zhang <chenzhang@kylinos.cn> Signed-off-by:
-
David Howells authored
When trying to get a file lock on an AFS file, the server may return UAEAGAIN to indicate that the lock is already held. This is currently translated by the default path to -EREMOTEIO. Translate it instead to -EAGAIN so that we know we can retry it. Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Jeffrey E Altman <jaltman@auristor.com> cc: Marc Dionne <marc.dionne@auristor.com> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/166075761334.3533338.2591992675160918098.stgit@warthog.procyon.org.uk/Signed-off-by:
-
git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fix from Russell King: "Just one fix for now for the AMBA bus code from Isaac Manjarres" * tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 9229/1: amba: Fix use-after-free in amba_read_periphid()
-
- 06 Sep, 2022 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofsLinus Torvalds authored
Pull erofs fixes from Gao Xiang: - Fix return codes in erofs_fscache_{meta_,}read_folio error paths - Fix potential wrong pcluster sizes for later non-4K lclusters - Fix in-memory pcluster use-after-free on UP platforms * tag 'erofs-for-6.0-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs: erofs: fix pcluster use-after-free on UP platforms erofs: avoid the potentially wrong m_plen for big pcluster erofs: fix error return code in erofs_fscache_{meta_,}read_folio -
jerry.meng authored
add support for Quectel RM520N which is based on Qualcomm SDX62 chip. 0x0801: DIAG + NMEA + AT + MODEM + RMNET T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0801 Rev= 5.04 S: Manufacturer=Quectel S: Product=RM520N-GL S: SerialNumber=384af524 C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
jerry.meng <jerry-meng@foxmail.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/tencent_E50CA8A206904897C2D20DDAE90731183C05@qq.comSigned-off-by:
-
Christian Marangi authored
of_device_get_match_data is called on priv->dev before priv->dev is actually set. Move of_device_get_match_data after priv->dev is correctly set to fix this kernel panic. Fixes: 3bb0844e ("net: dsa: qca8k: cache match data to speed up access") Signed-off-by:
Christian Marangi <ansuelsmth@gmail.com> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20220904215319.13070-1-ansuelsmth@gmail.comSigned-off-by:
-
Neal Cardwell authored
Fix a bug reported and analyzed by Nagaraj Arankal, where the handling of a spurious non-SACK RTO could cause a connection to fail to clear retrans_stamp, causing a later RTO to very prematurely time out the connection with ETIMEDOUT. Here is the buggy scenario, expanding upon Nagaraj Arankal's excellent report: (*1) Send one data packet on a non-SACK connection (*2) Because no ACK packet is received, the packet is retransmitted and we enter CA_Loss; but this retransmission is spurious. (*3) The ACK for the original data is received. The transmitted packet is acknowledged. The TCP timestamp is before the retrans_stamp, so tcp_may_undo() returns true, and tcp_try_undo_loss() returns true without changing state to Open (because tcp_is_sack() is false), and tcp_process_loss() returns without calling tcp_try_undo_recovery(). Normally after undoing a CA_Loss episode, tcp_fastretrans_alert() would see that the connection has returned to CA_Open and fall through and call tcp_try_to_open(), which would set retrans_stamp to 0. However, for non-SACK connections we hold the connection in CA_Loss, so do not fall through to call tcp_try_to_open() and do not set retrans_stamp to 0. So retrans_stamp is (erroneously) still non-zero. At this point the first "retransmission event" has passed and been recovered from. Any future retransmission is a completely new "event". However, retrans_stamp is erroneously still set. (And we are still in CA_Loss, which is correct.) (*4) After 16 minutes (to correspond with tcp_retries2=15), a new data packet is sent. Note: No data is transmitted between (*3) and (*4) and we disabled keep alives. The socket's timeout SHOULD be calculated from this point in time, but instead it's calculated from the prior "event" 16 minutes ago (step (*2)). (*5) Because no ACK packet is received, the packet is retransmitted. (*6) At the time of the 2nd retransmission, the socket returns ETIMEDOUT, prematurely, because retrans_stamp is (erroneously) too far in the past (set at the time of (*2)). This commit fixes this bug by ensuring that we reuse in tcp_try_undo_loss() the same careful logic for non-SACK connections that we have in tcp_try_undo_recovery(). To avoid duplicating logic, we factor out that logic into a new tcp_is_non_sack_preventing_reopen() helper and call that helper from both undo functions. Fixes: da34ac76 ("tcp: only undo on partial ACKs in CA_Loss") Reported-by:Nagaraj Arankal <nagaraj.p.arankal@hpe.com> Link: https://lore.kernel.org/all/SJ0PR84MB1847BE6C24D274C46A1B9B0EB27A9@SJ0PR84MB1847.NAMPRD84.PROD.OUTLOOK.COM/Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Reviewed-by:
-
- 05 Sep, 2022 12 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Arnd Bergmann: "These are the expected fixes for the SoC tree. I have let the patches pile up a little too long, so this is bigger than I would have liked. - Minor build fixes for Broadcom STB and NXP i.MX8M SoCs as well\ as TEE firmware - Updates to the MAINTAINERS file for the PolarFire SoC - Minor DT fixes for Renesas White Hawk and Arm Versatile and Juno platforms - A fix for a missing dependnecy in the NXP DPIO driver - Broadcom BCA fixes to the newly added devicetree files - Multiple fixes for Microchip AT91 based SoCs, dealing with self-refresh timings and regulator settings in DT - Several DT fixes for NXP i.MX platforms, dealing with incorrect GPIO settings, extraneous nodes, and a wrong clock setting" * tag 'soc-fixes-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (45 commits) soc: fsl: select FSL_GUTS driver for DPIO ARM: dts: at91: sama5d2_icp: don't keep vdd_other enabled all the time ARM: dts: at91: sama5d27_wlsom1: don't keep ldo2 enabled all the time ARM: dts: at91: sama7g5ek: specify proper regulator output ranges ARM: dts: at91: sama5d2_icp: specify proper regulator output ranges ARM: dts: at91: sama5d27_wlsom1: specify proper regulator output ranges ARM: at91: pm: fix DDR recalibration when resuming from backup and self-refresh ARM: at91: pm: fix self-refresh for sama7g5 soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugs ARM: configs: at91: remove CONFIG_MICROCHIP_PIT64B ARM: ixp4xx: fix typos in comments arm64: dts: renesas: r8a779g0: Fix HSCIF0 interrupt number tee: fix compiler warning in tee_shm_register() arm64: dts: freescale: verdin-imx8mp: fix atmel_mxt_ts reset polarity arm64: dts: freescale: verdin-imx8mm: fix atmel_mxt_ts reset polarity arm64: dts: imx8mp: Fix I2C5 GPIO assignment on i.MX8M Plus DHCOM arm64: dts: imx8mm-venice-gw7901: fix port/phy validation arm64: dts: verdin-imx8mm: add otg2 pd to usbphy soc: imx: gpcv2: Assert reset before ungating clock arm64: dts: ls1028a-qds-65bb: don't use in-band autoneg for 2500base-x ... -
Gao Xiang authored
During stress testing with CONFIG_SMP disabled, KASAN reports as below: ================================================================== BUG: KASAN: use-after-free in __mutex_lock+0xe5/0xc30 Read of size 8 at addr ffff8881094223f8 by task stress/7789 CPU: 0 PID: 7789 Comm: stress Not tainted 6.0.0-rc1-00002-g0d53d2e882f9 #3 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Call Trace: <TASK> .. __mutex_lock+0xe5/0xc30 .. z_erofs_do_read_page+0x8ce/0x1560 .. z_erofs_readahead+0x31c/0x580 .. Freed by task 7787 kasan_save_stack+0x1e/0x40 kasan_set_track+0x20/0x30 kasan_set_free_info+0x20/0x40 __kasan_slab_free+0x10c/0x190 kmem_cache_free+0xed/0x380 rcu_core+0x3d5/0xc90 __do_softirq+0x12d/0x389 Last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x97/0xb0 call_rcu+0x3d/0x3f0 erofs_shrink_workstation+0x11f/0x210 erofs_shrink_scan+0xdc/0x170 shrink_slab.constprop.0+0x296/0x530 drop_slab+0x1c/0x70 drop_caches_sysctl_handler+0x70/0x80 proc_sys_call_handler+0x20a/0x2f0 vfs_write+0x555/0x6c0 ksys_write+0xbe/0x160 do_syscall_64+0x3b/0x90 The root cause is that erofs_workgroup_unfreeze() doesn't reset to orig_val thus it causes a race that the pcluster reuses unexpectedly before freeing. Since UP platforms are quite rare now, such path becomes unnecessary. Let's drop such specific-designed path directly instead. Fixes: 73f5c66d ("staging: erofs: fix `erofs_workgroup_{try_to_freeze, unfreeze}'") Reviewed-by:
Yue Hu <huyue2@coolpad.com> Reviewed-by:
Chao Yu <chao@kernel.org> Link: https://lore.kernel.org/r/20220902045710.109530-1-hsiangkao@linux.alibaba.comSigned-off-by:
Gao Xiang <hsiangkao@linux.alibaba.com>
-
Yue Hu authored
Actually, 'compressedlcs' stores compressed block count rather than lcluster count. Therefore, the number of bits for shifting the count should be 'LOG_BLOCK_SIZE' rather than 'lclusterbits' although current lcluster size is 4K. The value of 'm_plen' will be wrong once we enable the non 4K-sized lcluster. Signed-off-by:
-
Sun Ke authored
If erofs_fscache_alloc_request fail and then goto out, it will return 0. it should return a negative error code instead of 0. Fixes: d435d532 ("erofs: change to use asynchronous io for fscache readpage/readahead") Signed-off-by:
Sun Ke <sunke32@huawei.com> Reviewed-by:
Jingbo Xu <jefflexu@linux.alibaba.com> Reviewed-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetoothDavid S. Miller authored
Luiz Augusto von Dentz says: ==================== bluetooth pull request for net: - Fix regression preventing ACL packet transmission ==================== Signed-off-by: -
Christophe JAILLET authored
There is no point to call pcim_iounmap_regions() in the remove function, this frees a managed resource that would be release by the framework anyway. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Greg Kroah-Hartman authored
When calling debugfs_lookup() the result must have dput() called on it, otherwise the memory will leak over time. Fix this up to be much simpler logic and only create the root debugfs directory once when the driver is first accessed. That resolves the memory leak and makes things more obvious as to what the intent is. Cc: Marcin Wojtas <mw@semihalf.com> Cc: Russell King <linux@armlinux.org.uk> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: netdev@vger.kernel.org Cc: stable <stable@kernel.org> Fixes: 21da57a2 ("net: mvpp2: add a debugfs interface for the Header Parser") Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
David Lebrun authored
The SRv6 layer allows defining HMAC data that can later be used to sign IPv6 Segment Routing Headers. This configuration is realised via netlink through four attributes: SEG6_ATTR_HMACKEYID, SEG6_ATTR_SECRET, SEG6_ATTR_SECRETLEN and SEG6_ATTR_ALGID. Because the SECRETLEN attribute is decoupled from the actual length of the SECRET attribute, it is possible to provide invalid combinations (e.g., secret = "", secretlen = 64). This case is not checked in the code and with an appropriately crafted netlink message, an out-of-bounds read of up to 64 bytes (max secret length) can occur past the skb end pointer and into skb_shared_info: Breakpoint 1, seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208 208 memcpy(hinfo->secret, secret, slen); (gdb) bt #0 seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208 #1 0xffffffff81e012e9 in genl_family_rcv_msg_doit (skb=skb@entry=0xffff88800b1f9f00, nlh=nlh@entry=0xffff88800b1b7600, extack=extack@entry=0xffffc90000ba7af0, ops=ops@entry=0xffffc90000ba7a80, hdrlen=4, net=0xffffffff84237580 <init_net>, family=<optimized out>, family=<optimized out>) at net/netlink/genetlink.c:731 #2 0xffffffff81e01435 in genl_family_rcv_msg (extack=0xffffc90000ba7af0, nlh=0xffff88800b1b7600, skb=0xffff88800b1f9f00, family=0xffffffff82fef6c0 <seg6_genl_family>) at net/netlink/genetlink.c:775 #3 genl_rcv_msg (skb=0xffff88800b1f9f00, nlh=0xffff88800b1b7600, extack=0xffffc90000ba7af0) at net/netlink/genetlink.c:792 #4 0xffffffff81dfffc3 in netlink_rcv_skb (skb=skb@entry=0xffff88800b1f9f00, cb=cb@entry=0xffffffff81e01350 <genl_rcv_msg>) at net/netlink/af_netlink.c:2501 #5 0xffffffff81e00919 in genl_rcv (skb=0xffff88800b1f9f00) at net/netlink/genetlink.c:803 #6 0xffffffff81dff6ae in netlink_unicast_kernel (ssk=0xffff888010eec800, skb=0xffff88800b1f9f00, sk=0xffff888004aed000) at net/netlink/af_netlink.c:1319 #7 netlink_unicast (ssk=ssk@entry=0xffff888010eec800, skb=skb@entry=0xffff88800b1f9f00, portid=portid@entry=0, nonblock=<optimized out>) at net/netlink/af_netlink.c:1345 #8 0xffffffff81dff9a4 in netlink_sendmsg (sock=<optimized out>, msg=0xffffc90000ba7e48, len=<optimized out>) at net/netlink/af_netlink.c:1921 ... (gdb) p/x ((struct sk_buff *)0xffff88800b1f9f00)->head + ((struct sk_buff *)0xffff88800b1f9f00)->end $1 = 0xffff88800b1b76c0 (gdb) p/x secret $2 = 0xffff88800b1b76c0 (gdb) p slen $3 = 64 '@' The OOB data can then be read back from userspace by dumping HMAC state. This commit fixes this by ensuring SECRETLEN cannot exceed the actual length of SECRET. Reported-by:Lucas Leong <wmliang.tw@gmail.com> Tested: verified that EINVAL is correctly returned when secretlen > len(secret) Fixes: 4f4853dc ("ipv6: sr: implement API to control SR HMAC structure") Signed-off-by:
David Lebrun <dlebrun@google.com> Signed-off-by:
-
David S. Miller authored
Hangbin Liu says: ==================== bonding: fix lladdr finding and confirmation This patch set fixed 3 issues when setting lladdr as bonding IPv6 target. Please see each patch for the details. v2: separate the patch to 3 parts ==================== Signed-off-by: -
Hangbin Liu authored
The unsolicited NA message with all-nodes multicast dest address should be valid, as this also means the link could reach the target. Also rename bond_validate_ns() to bond_validate_na(). Reported-by:
LiLiang <liali@redhat.com> Fixes: 5e1eeef6 ("bonding: NS target should accept link local address") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Hangbin Liu authored
When a link is enslave to bond, it need to set the interface down first. This makes the slave remove mac multicast address 33:33:00:00:00:01(The IPv6 multicast address ff02::1 is kept even when the interface down). When bond set the slave up, ipv6_mc_up() was not called due to commit c2edacf8 ("bonding / ipv6: no addrconf for slaves separately from master"). This is not an issue before we adding the lladdr target feature for bonding, as the mac multicast address will be added back when bond interface up and join group ff02::1. But after adding lladdr target feature for bonding. When user set a lladdr target, the unsolicited NA message with all-nodes multicast dest will be dropped as the slave interface never add 33:33:00:00:00:01 back. Fix this by calling ipv6_mc_up() to add 33:33:00:00:00:01 back when the slave interface up. Reported-by:
-
Hangbin Liu authored
When ns_ip6_target was set, the ipv6_dev_get_saddr() will be called to get available source address and send IPv6 neighbor solicit message. If the target is global address, ipv6_dev_get_saddr() will get any available src address. But if the target is link local address, ipv6_dev_get_saddr() will only get available address from our interface, i.e. the corresponding bond interface. But before bond interface up, all the address is tentative, while ipv6_dev_get_saddr() will ignore tentative address. This makes we can't find available link local src address, then bond_ns_send() will not be called and no NS message was sent. Finally bond interface will keep in down state. Fix this by sending NS with unspecified address if there is no available source address. Reported-by:
-
- 04 Sep, 2022 4 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Fix handling of PCI domains in /proc on 32-bit systems using the recently added support for numbering buses from zero for each domain. - A fix and a revert for some changes to use READ/WRITE_ONCE() which caused problems with KASAN enabled due to sanitisation calls being introduced in low-level paths that can't cope with it. - Fix build errors on 32-bit caused by the syscall table being misaligned sometimes. - Two fixes to get IBM Cell native machines booting again, which had bit-rotted while my QS22 was temporarily out of action. - Fix the papr_scm driver to not assume the order of events returned by the hypervisor is stable, and a related compile fix. Thanks to Aneesh Kumar K.V, Christophe Leroy, Jordan Niethe, Kajol Jain, Masahiro Yamada, Nathan Chancellor, Pali Rohár, Vaibhav Jain, and Zhouyi Zhou. * tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register() Revert "powerpc/irq: Don't open code irq_soft_mask helpers" powerpc: Fix hard_irq_disable() with sanitizer powerpc/rtas: Fix RTAS MSR[HV] handling for Cell Revert "powerpc: Remove unused FW_FEATURE_NATIVE references" powerpc: align syscall table for ppc32 powerpc/pci: Enable PCI domains in /proc when PCI bus numbers are not unique powerpc/papr_scm: Fix nvdimm event mappings
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull kvm fixes from Paolo Bonzini: "s390: - PCI interpretation compile fixes RISC-V: - fix unused variable warnings in vcpu_timer.c - move extern sbi_ext declarations to a header x86: - check validity of argument to KVM_SET_MP_STATE - use guest's global_ctrl to completely disable guest PEBS - fix a memory leak on memory allocation failure - mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES - fix build failure with Clang integrated assembler - fix MSR interception - always flush TLBs when enabling dirty logging" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: check validity of argument to KVM_SET_MP_STATE perf/x86/core: Completely disable guest PEBS via guest's global_ctrl KVM: x86: fix memoryleak in kvm_arch_vcpu_create() KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES KVM: s390: pci: Hook to access KVM lowlevel from VFIO riscv: kvm: move extern sbi_ext declarations to a header riscv: kvm: vcpu_timer: fix unused variable warnings KVM: selftests: Fix ambiguous mov in KVM_ASM_SAFE() KVM: selftests: Fix KVM_EXCEPTION_MAGIC build with Clang KVM: VMX: Heed the 'msr' argument in msr_write_intercepted() kvm: x86: mmu: Always flush TLBs when enabling dirty logging kvm: x86: mmu: Drop the need_remote_flush() function
-
Nick Desaulniers authored
-Wformat was recently re-enabled for builds with clang, then quickly re-disabled, due to concerns stemming from the frequency of default argument promotion related warning instances. commit 258fafcd ("Makefile.extrawarn: re-enable -Wformat for clang") commit 21f9c8a1 ("Revert "Makefile.extrawarn: re-enable -Wformat for clang"") ISO WG14 has ratified N2562 to address default argument promotion explicitly for printf, as part of the upcoming ISO C2X standard. The behavior of clang was changed in clang-16 to not warn for the cited cases in all language modes. Add a version check, so that users of clang-16 now get the full effect of -Wformat. For older clang versions, re-enable flags under the -Wformat group that way users still get some useful checks related to format strings, without noisy default argument promotion warnings. I intentionally omitted -Wformat-y2k and -Wformat-security from being re-enabled, which are also part of -Wformat in clang-16. Link: https://github.com/ClangBuiltLinux/linux/issues/378 Link: https://github.com/llvm/llvm-project/issues/57102 Link: https://www.open-std.org/jtc1/sc22/wg14/www/docs/n2562.pdfSuggested-by:
Justin Stitt <jstitt007@gmail.com> Suggested-by:
Nathan Chancellor <nathan@kernel.org> Suggested-by:
Youngmin Nam <youngmin.nam@samsung.com> Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Reviewed-by:
Masahiro Yamada <masahiroy@kernel.org> Reviewed-by:
-
