- 17 Oct, 2019 40 commits
-
-
Fabrice Gasnier authored
[ Upstream commit dcb10920 ] End of conversion may be handled by using IRQ or DMA. There may be a race when two conversions complete at the same time on several ADCs. EOC can be read as 'set' for several ADCs, with: - an ADC configured to use IRQs. EOCIE bit is set. The handler is normally called in this case. - an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA request instead. It's then automatically cleared by DMA read. But the handler gets called due to status bit is temporarily set (IRQ triggered by the other ADC). So both EOC status bit in CSR and EOCIE control bit must be checked before invoking the interrupt handler (e.g. call ISR only for IRQ-enabled ADCs). Fixes: 2763ea05 ("iio: adc: stm32: add optional dma support") Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Fabrice Gasnier authored
[ Upstream commit 31922f62 ] Move STM32 ADC registers definitions to common header. This is precursor patch to: - iio: adc: stm32-adc: fix a race when using several adcs with dma and irq It keeps registers definitions as a whole block, to ease readability and allow simple access path to EOC bits (readl) in stm32-adc-core driver. Fixes: 2763ea05 ("iio: adc: stm32: add optional dma support") Signed-off-by:
-
Bartosz Golaszewski authored
[ Upstream commit e735244e ] When emulating open-drain/open-source by not actively driving the output lines - we're simply changing their mode to input. This is wrong as it will then make it impossible to change the value of such line - it's now considered to actually be in input mode. If we want to still use the direction_input() callback for simplicity then we need to set FLAG_IS_OUT manually in gpiod_direction_output() and not clear it in gpio_set_open_drain_value_commit() and gpio_set_open_source_value_commit(). Fixes: c663e5f5 ("gpio: support native single-ended hardware drivers") Cc: stable@vger.kernel.org Reported-by:
Kent Gibson <warthog618@gmail.com> Signed-off-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> [Bartosz: backported to v5.3, v4.19] Signed-off-by:
-
Brian Norris authored
[ Upstream commit 442f1e74 ] Commit 4b708b7b ("firmware: google: check if size is valid when decoding VPD data") adds length checks, but the new vpd_decode_entry() function botched the logic -- it adds the key length twice, instead of adding the key and value lengths separately. On my local system, this means vpd.c's vpd_section_create_attribs() hits an error case after the first attribute it parses, since it's no longer looking at the correct offset. With this patch, I'm back to seeing all the correct attributes in /sys/firmware/vpd/... Fixes: 4b708b7b ("firmware: google: check if size is valid when decoding VPD data") Cc: <stable@vger.kernel.org> Cc: Hung-Te Lin <hungte@chromium.org> Signed-off-by:
Brian Norris <briannorris@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Guenter Roeck <groeck@chromium.org> Link: https://lore.kernel.org/r/20190930214522.240680-1-briannorris@chromium.orgSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Dan Carpenter authored
commit 518a8671 upstream. The "mode" and "level" variables are enums and in this context GCC will treat them as unsigned ints so the error handling is never triggered. I also removed the bogus initializer because it isn't required any more and it's sort of confusing. [akpm@linux-foundation.org: reduce implicit and explicit typecasting] [akpm@linux-foundation.org: fix return value, add comment, per Matthew] Link: http://lkml.kernel.org/r/20190925110449.GO3264@mwanda Fixes: 3cadfa2b ("mm/vmpressure.c: convert to use match_string() helper") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
David Rientjes <rientjes@google.com> Reviewed-by:
Matthew Wilcox <willy@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Enrico Weigelt <info@metux.net> Cc: Kate Stewart <kstewart@linuxfoundation.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Michal Hocko authored
commit b0f53dbc upstream. Partially revert 16db3d3f ("kernel/sysctl.c: threads-max observe limits") because the patch is causing a regression to any workload which needs to override the auto-tuning of the limit provided by kernel. set_max_threads is implementing a boot time guesstimate to provide a sensible limit of the concurrently running threads so that runaways will not deplete all the memory. This is a good thing in general but there are workloads which might need to increase this limit for an application to run (reportedly WebSpher MQ is affected) and that is simply not possible after the mentioned change. It is also very dubious to override an admin decision by an estimation that doesn't have any direct relation to correctness of the kernel operation. Fix this by dropping set_max_threads from sysctl_max_threads so any value is accepted as long as it fits into MAX_THREADS which is important to check because allowing more threads could break internal robust futex restriction. While at it, do not use MIN_THREADS as the lower boundary because it is also only a heuristic for automatic estimation and admin might have a good reason to stop new threads to be created even when below this limit. This became more severe when we switched x86 from 4k to 8k kernel stacks. Starting since 6538b8ea ("x86_64: expand kernel stack to 16K") (3.16) we use THREAD_SIZE_ORDER = 2 and that halved the auto-tuned value. In the particular case 3.12 kernel.threads-max = 515561 4.4 kernel.threads-max = 200000 Neither of the two values is really insane on 32GB machine. I am not sure we want/need to tune the max_thread value further. If anything the tuning should be removed altogether if proven not useful in general. But we definitely need a way to override this auto-tuning. Link: http://lkml.kernel.org/r/20190922065801.GB18814@dhcp22.suse.cz Fixes: 16db3d3f ("kernel/sysctl.c: threads-max observe limits") Signed-off-by:
Michal Hocko <mhocko@suse.com> Reviewed-by:
"Eric W. Biederman" <ebiederm@xmission.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Pavel Shilovsky authored
commit 0b3d0ef9 upstream. Mark inode for force revalidation if LOOKUP_REVAL flag is set. This tells the client to actually send a QueryInfo request to the server to obtain the latest metadata in case a directory or a file were changed remotely. Only do that if the client doesn't have a lease for the file to avoid unneeded round trips to the server. Cc: <stable@vger.kernel.org> Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Pavel Shilovsky authored
commit c82e5ac7 upstream. Currently the client indicates that a dentry is stale when inode numbers or type types between a local inode and a remote file don't match. If this is the case attributes is not being copied from remote to local, so, it is already known that the local copy has stale metadata. That's why the inode needs to be marked for revalidation in order to tell the VFS to lookup the dentry again before openning a file. This prevents unexpected stale errors to be returned to the user space when openning a file. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Pavel Shilovsky authored
commit 30573a82 upstream. Currently if the client identifies problems when processing metadata returned in CREATE response, the open handle is being leaked. This causes multiple problems like a file missing a lease break by that client which causes high latencies to other clients accessing the file. Another side-effect of this is that the file can't be deleted. Fix this by closing the file after the client hits an error after the file was opened and the open descriptor wasn't returned to the user space. Also convert -ESTALE to -EOPENSTALE to allow the VFS to revalidate a dentry and retry the open. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Harshad Shirwadkar authored
commit b84477d3 upstream. scale_up wakes up waiters after scaling up. But after scaling max, it should not wake up more waiters as waiters will not have anything to do. This patch fixes this by making scale_up (and also scale_down) return when threshold is reached. This bug causes increased fdatasync latency when fdatasync and dd conv=sync are performed in parallel on 4.19 compared to 4.14. This bug was introduced during refactoring of blk-wbt code. Fixes: a7905043 ("blk-rq-qos: refactor out common elements of blk-wbt") Cc: stable@vger.kernel.org Cc: Josef Bacik <jbacik@fb.com> Signed-off-by:
Harshad Shirwadkar <harshadshirwadkar@gmail.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Steve MacLean authored
commit b59711e9 upstream. During perf inject --jit, JIT_CODE_MOVE records were injecting MMAP records with an incorrect filename. Specifically it was missing the ".so" suffix. Further the JIT_CODE_LOAD record were silently truncating the jr->load.code_index field to 32 bits before generating the filename. Make both records emit the same filename based on the full 64 bit code_index field. Fixes: 9b07e27f ("perf inject: Add jitdump mmap injection support") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by:
Steve MacLean <Steve.MacLean@Microsoft.com> Acked-by:
Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Brian Robbins <brianrob@microsoft.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com> Cc: John Keeping <john@metanate.com> Cc: John Salem <josalem@microsoft.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: Tom McDonald <thomas.mcdonald@microsoft.com> Link: http://lore.kernel.org/lkml/BN8PR21MB1362FF8F127B31DBF4121528F7800@BN8PR21MB1362.namprd21.prod.outlook.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Ian Rogers authored
commit 7d4c85b7 upstream. The 'test_dir' variable is assigned to the 'release' array which is out-of-scope 3 lines later. Extend the scope of the 'release' array so that an out-of-scope array isn't accessed. Bug detected by clang's address sanitizer. Fixes: 07bc5c69 ("perf tools: Make fetch_kernel_version() publicly available") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by:
Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lore.kernel.org/lkml/20190926220018.25402-1-irogers@google.comSigned-off-by:
-
Ard Biesheuvel authored
commit c05f8f92 upstream. The kernel command line option efivar_ssdt= allows the name to be specified of an EFI variable containing an ACPI SSDT table that should be loaded into memory by the OS, and treated as if it was provided by the firmware. Currently, that code will always iterate over the EFI variables and compare each name with the provided name, even if the command line option wasn't set to begin with. So bail early when no variable name was provided. This works around a boot regression on the 2012 Mac Pro, as reported by Scott. Tested-by:
Scott Talbert <swt@techie.net> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: <stable@vger.kernel.org> # v4.9+ Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Dave Young <dyoung@redhat.com> Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Cc: Jerry Snitselaar <jsnitsel@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Lukas Wunner <lukas@wunner.de> Cc: Lyude Paul <lyude@redhat.com> Cc: Matthew Garrett <mjg59@google.com> Cc: Octavian Purdila <octavian.purdila@intel.com> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Cc: linux-integrity@vger.kernel.org Fixes: 475fb4e8 ("efi / ACPI: load SSTDs from EFI variables") Link: https://lkml.kernel.org/r/20191002165904.8819-3-ard.biesheuvel@linaro.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
David Frey authored
commit 82f30156 upstream. When an end-of-conversion interrupt is received after performing a single-shot reading of the light sensor, the driver was waking up the result ready queue before checking opt->ok_to_ignore_lock to determine if it should unlock the mutex. The problem occurred in the case where the other thread woke up and changed the value of opt->ok_to_ignore_lock to false prior to the interrupt thread performing its read of the variable. In this case, the mutex would be unlocked twice. Signed-off-by:
David Frey <dpfrey@gmail.com> Reviewed-by:
Andreas Dannenberg <dannenberg@ti.com> Fixes: 94a9b7b1 ("iio: light: add support for TI's opt3001 light sensor") Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Hans de Goede authored
commit 97291741 upstream. Since commit 9bcf15f7 ("iio: adc: axp288: Fix TS-pin handling") we preserve the bias current set by the firmware at boot. This fixes issues we were seeing on various models, but it seems our old hardcoded 80ųA bias current was working around a firmware bug on at least one model laptop. In order to both have our cake and eat it, this commit adds a dmi based list of models where we need to override the firmware set bias current and adds the one model we now know needs this to it: The Lenovo Ideapad 100S (11 inch version). Fixes: 9bcf15f7 ("iio: adc: axp288: Fix TS-pin handling") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Marco Felsch authored
commit c62dd449 upstream. Since commit 0f7ddcc1 ("iio:adc:ad799x: Write default config on probe and reset alert status on probe") the error path is wrong since it leaves the vref regulator on. Fix this by disabling both regulators. Fixes: 0f7ddcc1 ("iio:adc:ad799x: Write default config on probe and reset alert status on probe") Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Reviewed-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Andreas Klinger authored
commit 4043ecfb upstream. Fix bug in sampling function hx711_cycle() when interrupt occures while PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of the sensor is entered which in turn leads to a wrong measurement. Switch off interrupts during a PD_SCK high period and move query of DOUT to the latest point of time which is at the end of PD_SCK low period. This bug exists in the driver since it's initial addition. The more interrupts on the system the higher is the probability that it happens. Fixes: c3b2fdd0 ("iio: adc: hx711: Add IIO driver for AVIA HX711") Signed-off-by:
Andreas Klinger <ak@it-klinger.de> Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Navid Emamdoost authored
commit 80b15db5 upstream. In vt6655_probe, if vnt_init() fails the cleanup code needs to be called like other error handling cases. The call to device_free_info() is added. Fixes: 67013f2c ("staging: vt6655: mac80211 conversion add main mac80211 functions") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191004200319.22394-1-navid.emamdoost@gmail.comSigned-off-by:
-
Navid Emamdoost authored
commit 5bdea606 upstream. In fbtft_framebuffer_alloc the error handling path should take care of releasing frame buffer after it is allocated via framebuffer_alloc, too. Therefore, in two failure cases the goto destination is changed to address this issue. Fixes: c296d5f9 ("staging: fbtft: core support") Signed-off-by:
Dan Carpenter <dan.carpenter@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190930030949.28615-1-navid.emamdoost@gmail.comSigned-off-by:
-
Bruce Chen authored
commit e91aafcb upstream. When toggling the level trigger to emulate the edge trigger, the EIC offset is incorrect without adding the corresponding bank index, thus fix it. Fixes: 7bf0d7f6 ("gpio: eic: Add edge trigger emulation for EIC") Cc: stable@vger.kernel.org Signed-off-by:
Bruce Chen <bruce.chen@unisoc.com> Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
-
Alexander Usyskin authored
commit f8204f0d upstream. The fixed MKHI client on PCH 6 gen platforms does not support fw version retrieval. The error is not fatal, but it fills up the kernel logs and slows down the driver start. This patch disables requesting FW version on GEN6 and earlier platforms. Fixes warning: [ 15.964298] mei mei::55213584-9a29-4916-badf-0fb7ed682aeb:01: Could not read FW version [ 15.964301] mei mei::55213584-9a29-4916-badf-0fb7ed682aeb:01: version command failed -5 Cc: <stable@vger.kernel.org> +v4.18 Cc: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20191004181722.31374-1-tomas.winkler@intel.comSigned-off-by:
-
Tomas Winkler authored
commit 4d86dfd3 upstream. Add Comet Point devices IDs for Comet Lake U platforms. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 726b55d0 upstream. The driver was accessing its struct usb_device in its release() callback without holding a reference. This would lead to a use-after-free whenever the device was disconnected while the character device was still open. Fixes: fef526ca ("USB: legousbtower: remove custom debug macro") Cc: stable <stable@vger.kernel.org> # 3.12 Signed-off-by:
Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191009153848.8664-5-johan@kernel.orgSigned-off-by:
-
Johan Hovold authored
commit 0b074f69 upstream. The driver would return with a nonzero open count in case the reset control request failed. This would prevent any further attempts to open the char dev until the device was disconnected. Fix this by incrementing the open count only on successful open. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit cd81e6fa upstream. The driver is using its struct usb_device pointer as an inverted disconnected flag, but was setting it to NULL before making sure all completion handlers had run. This could lead to a NULL-pointer dereference in a number of dev_dbg and dev_err statements in the completion handlers which relies on said pointer. Fix this by unconditionally stopping all I/O and preventing resubmissions by poisoning the interrupt URBs at disconnect and using a dedicated disconnected flag. This also makes sure that all I/O has completed by the time the disconnect callback returns. Fixes: 9d974b2a ("USB: legousbtower.c: remove err() usage") Fixes: fef526ca ("USB: legousbtower: remove custom debug macro") Fixes: 4dae9963 ("USB: legotower: remove custom debug macro and module parameter") Cc: stable <stable@vger.kernel.org> # 3.5 Signed-off-by:
-
Johan Hovold authored
commit 33a78132 upstream. Fix a potential deadlock if disconnect races with open. Since commit d4ead16f ("USB: prevent char device open/deregister race") core holds an rw-semaphore while open is called and when releasing the minor number during deregistration. This can lead to an ABBA deadlock if a driver takes a lock in open which it also holds during deregistration. This effectively reverts commit 78663ecc ("USB: disconnect open race in legousbtower") which needlessly introduced this issue after a generic fix for this race had been added to core by commit d4ead16f ("USB: prevent char device open/deregister race"). Fixes: 78663ecc ("USB: disconnect open race in legousbtower") Cc: stable <stable@vger.kernel.org> # 2.6.24 Reported-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com Tested-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com Signed-off-by:
-
Johan Hovold authored
commit 1d427be4 upstream. Make sure to check for short transfers when retrieving the version information at probe to avoid leaking uninitialised slab data when logging it. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Yoshihiro Shimoda authored
commit 4d599cd3 upstream. According to usb_ep_set_halt()'s description, __usbhsg_ep_set_halt_wedge() should return -EAGAIN if the IN endpoint has any queue or data. Otherwise, this driver is possible to cause just STALL without sending a short packet data on g_mass_storage driver, and then a few resetting a device happens on a host side during a usb enumaration. Fixes: 2f98382d ("usb: renesas_usbhs: Add Renesas USBHS Gadget") Cc: <stable@vger.kernel.org> # v3.0+ Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1569924633-322-3-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
-
Yoshihiro Shimoda authored
commit 1aae1394 upstream. The commit 97664a20 ("usb: renesas_usbhs: shrink spin lock area") had added a usbhsg_pipe_disable() calling into __usbhsg_ep_set_halt_wedge() accidentally. But, this driver should not call the usbhsg_pipe_disable() because the function discards all queues. So, this patch removes it. Fixes: 97664a20 ("usb: renesas_usbhs: shrink spin lock area") Cc: <stable@vger.kernel.org> # v3.1+ Signed-off-by:
-
Jacky.Cao@sony.com authored
commit 2636d49b upstream. The power budget for SuperSpeed mode should be 900 mA according to USB specification, so set the power budget to 900mA for dummy_start_ss which is only used for SuperSpeed mode. If the max power consumption of SuperSpeed device is larger than 500 mA, insufficient available bus power error happens in usb_choose_configuration function when the device connects to dummy hcd. Signed-off-by:
Jacky Cao <Jacky.Cao@sony.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/16EA1F625E922C43B00B9D82250220500871CDE5@APYOKXMS108.ap.sony.comSigned-off-by:
-
Johan Hovold authored
commit 177238c3 upstream. Add missing bulk-in endpoint sanity check to prevent uninitialised stack data from being reported to the system log and used as endpoint addresses. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+5630ca7c3b2be5c9da5e@syzkaller.appspotmail.com Signed-off-by:
Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20191003070931.17009-1-johan@kernel.orgSigned-off-by:
-
Johan Hovold authored
commit eb7f5a49 upstream. Make sure to stop all I/O on disconnect by adding a disconnected flag which is used to prevent new I/O from being started and by stopping all ongoing I/O before returning. This also fixes a potential use-after-free on driver unbind in case the driver data is freed before the completion handler has run. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> # 7bbe990cSigned-off-by:
-
Johan Hovold authored
commit d51bdb93 upstream. Since commit c2b71462 ("USB: core: Fix bug caused by duplicate interface PM usage counter") USB drivers must always balance their runtime PM gets and puts, including when the driver has already been unbound from the interface. Leaving the interface with a positive PM usage counter would prevent a later bound driver from suspending the device. Fixes: c2b71462 ("USB: core: Fix bug caused by duplicate interface PM usage counter") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Reinhard Speyerer authored
commit dfbac2f4 upstream. Add support for the serial ports of Cinterion CLS8 devices. T: Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=00b0 Rev= 3.18 S: Manufacturer=GEMALTO S: Product=USB Modem C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
Reinhard Speyerer <rspmn@arcor.de> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Daniele Palmas authored
commit 5eb3f4b8 upstream. This patch adds the following Telit FN980 compositions: 0x1050: tty, adb, rmnet, tty, tty, tty, tty 0x1051: tty, adb, mbim, tty, tty, tty, tty 0x1052: rndis, tty, adb, tty, tty, tty, tty 0x1053: tty, adb, ecm, tty, tty, tty, tty Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Beni Mahler authored
commit 357f16d9 upstream. Both devices added here have a FTDI chip inside. The device from Echelon is called 'Network Interface' it is actually a LON network gateway. ID 0403:8348 Future Technology Devices International, Ltd https://www.eltako.com/fileadmin/downloads/de/datenblatt/Datenblatt_PL-SW-PROF.pdf ID 0920:7500 Network Interface https://www.echelon.com/products/u20-usb-network-interfaceSigned-off-by:
Beni Mahler <beni.mahler@gmx.net> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 7d7e21fa upstream. Fix NULL-pointer dereferences on open() and write() which can be triggered by a malicious USB device. The current URB allocation helper would fail to initialise the newly allocated URB if the device has unexpected endpoint descriptors, something which could lead NULL-pointer dereferences in a number of open() and write() paths when accessing the URB. For example: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:usb_clear_halt+0x11/0xc0 ... Call Trace: ? tty_port_open+0x4d/0xd0 keyspan_open+0x70/0x160 [keyspan] serial_port_activate+0x5b/0x80 [usbserial] tty_port_open+0x7b/0xd0 ? check_tty_count+0x43/0xa0 tty_open+0xf1/0x490 BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:keyspan_write+0x14e/0x1f3 [keyspan] ... Call Trace: serial_write+0x43/0xa0 [usbserial] n_tty_write+0x1af/0x4f0 ? do_wait_intr_irq+0x80/0x80 ? process_echoes+0x60/0x60 tty_write+0x13f/0x2f0 BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:keyspan_usa26_send_setup+0x298/0x305 [keyspan] ... Call Trace: keyspan_open+0x10f/0x160 [keyspan] serial_port_activate+0x5b/0x80 [usbserial] tty_port_open+0x7b/0xd0 ? check_tty_count+0x43/0xa0 tty_open+0xf1/0x490 Fixes: fdcba53e ("fix for bugzilla #7544 (keyspan USB-to-serial converter)") Cc: stable <stable@vger.kernel.org> # 2.6.21 Reviewed-by:
-
Randy Dunlap authored
commit a553add0 upstream. Call uart_unregister_driver() conditionally instead of unconditionally, only if it has been previously registered. This uses driver.state, just as the sh-sci.c driver does. Fixes this null pointer dereference in tty_unregister_driver(), since the 'driver' argument is null: general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI RIP: 0010:tty_unregister_driver+0x25/0x1d0 Fixes: 238b8721 ("[PATCH] serial uartlite driver") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: stable <stable@vger.kernel.org> Cc: Peter Korsgaard <jacmet@sunsite.dk> Link: https://lore.kernel.org/r/9c8e6581-6fcc-a595-0897-4d90f5d710df@infradead.orgSigned-off-by:
-
Johan Hovold authored
commit 58ecf131 upstream. The driver was using its struct usb_interface pointer as an inverted disconnected flag, but was setting it to NULL before making sure all completion handlers had run. This could lead to a NULL-pointer dereference in a number of dev_dbg, dev_warn and dev_err statements in the completion handlers which relies on said pointer. Fix this by unconditionally stopping all I/O and preventing resubmissions by poisoning the interrupt URBs at disconnect and using a dedicated disconnected flag. This also makes sure that all I/O has completed by the time the disconnect callback returns. Fixes: 2824bd25 ("[PATCH] USB: add ldusb driver") Cc: stable <stable@vger.kernel.org> # 2.6.13 Signed-off-by:
-
Johan Hovold authored
commit 93ddb1f5 upstream. The driver was accessing its struct usb_interface in its release() callback without holding a reference. This would lead to a use-after-free whenever the device was disconnected while the character device was still open. Fixes: 66e3e591 ("usb: Add driver for Altus Metrum ChaosKey device (v2)") Cc: stable <stable@vger.kernel.org> # 4.1 Signed-off-by:
-
